Euroflex M4S User Manual

M4S

HYBRID FLOOR STEAMER

All in One Steam Cleaner

INSTRUCTION MANUAL

Before using this product, please read the instructions and keep it for future references.

IMPORTANT SAF

When using an electrical appliance, basic safety
precautions should always be observed, including the
following:
Read all instructions before using this appliance.

WARNING! To reduce the risk of fi re, electrical shock,

or injury:

1. This appliance is authorized for household/domestic
use only.

2. Do not charge or use outdoors or on wet surfaces. Do
not immerse the fl oor steamer in water or other liquids.

3. Do not allow fl oor steamer to be used as a toy. Close
attention is necessary when used by or near children.
Do not leave Steamer unattended. Always unplug
unit when not in use.

4. Use only as described and for the uses described
in this manual. Use only manufacturer’s approved
and supplied parts and accessories. Use of other
accessories is not recommended and will void the
warranty.

5. Always make sure the Handle Assembly is in the upright
position before plugging in or unplugging. Keep cord
away from heated surfaces (e.g., cooking surfaces)
and sharp edges and corners.

6. Do not use if power cord or plug has been damaged,
or if any part of appliance has been dropped,
damaged, left outdoors, or dropped in water. Do not
attempt to disassemble or repair appliance. Return it
to manufacturer or an authorized service center for
examination or repair.

7. Do not wrap cord too tightly around appliance. Never
carry by the cord or yank to disconnect from an outlet.
To unplug, always grasp plug to remove from outlet –
do not pull on cord.

8. Do not handle the cord or the appliance with wet
hands or bare feet.

2

Safety Instruction

ETY INSTRUCTION

9. Look closely at steamer and follow all labels and
marking instructions.

10. Do not put any objects into openings. Do not use with any
opening blocked.

11. Keep hair, loose clothing, fi ngers and all parts of body
away from openings and moving parts.

12. Before fi lling with water or emptying, always place
Handle Assembly in upright position, unplug the
appliance and allow it to briefl y cool down. Always
turn the Boiler Cap slowly to open the water tank – this
will allow any remaining steam to escape gradually.

13. Use caution while emptying the appliance. Contact
with hot water or steam may cause burns.

14. To unlock the steam cleaner,
press the safety button on the
right side (1).

.

At the end of use it is
recommended to lock the
appliance pressing the button
on the left side (2).

15. Never use cleaning solutions, perfumes, oils or other

chemical substances other than tap or distilled/
demineralized water in the Steamer. Use of chemicals
may damage Steamer and will void the warranty.

16. Be sure Boiler Cap is (and remains) closed during use.

17. When in use, never turn the appliance on its side. Do

not direct steam at people, animals or other electrical
equipment (i.e, inside an oven).

18. Do not operate around fl ammable or combustible

liquids such as gasoline or in areas where fumes may
be present.

Safety Instruction

3

IMPORTANT SAF

19. The Steamer is not intended for space heating
purposes.

20. To reduce the likelihood of circuit overload, do
not operate another high wattage appliance on
the same circuit. Plug in to a standard (220-240V,
50/60Hz) electrical outlet.

ATTENTION! This appliance is equipped with a 3-prong
grounded power cord. Insert only into a 3-prong
grounded electrical outlet. Do not try to remove the
contacts of the grounded connection.

21. Do not use extension cords or outlets with inadequate
voltage. Use only heavy duty, high-rated extensions
cords.

22. Store appliance indoors in a cool, dry place.

23. If appliance is damaged, it must be repaired by
manufacturer in order to avoid safety issues to the
operator.

24. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of appliance by a
person responsible for their safety.

25. Read and follow all important notices in this guide.

CAUTIONS

• Extreme care should be taken when opening the
Boiler Cap as it may become hot during use and
escaping steam can cause scalding.

4

Safety Instruction

ETY INSTRUCTION

CAUTIONS

•Do not use your Floor Steamer without a Hard Surface
Pad or Carpet Glide & Pad attached to the system.

•Never leave your Floor Steamer in one spot on any
surface for any period of time. Make sure that the Floor
Steamer Handle Assembly is in the full “UP POSITION”
when not in use - this turns the Steamer Off.

Save your back

No need to
press hard

The steamer
does the
work for you

.

*IMPORTANT*

Please read all of the instructions for use and Important Safety
Instructions carefully. Remove and discard all packaging
materials and keep them out of the reach of children.

Eurofl ex relieves itself of any liability for damages that shall be
the result of improper use of the appliance, not in conformity
with what’s written in this instruction manual.

Attention: the photographs and/or drawings in this document are for illustrative
purposes only. Actual appliance and the accessories may vary due to product

enhancement.
Safety Informations in Digital Format: www.plastecs.it/warning

Safety Instruction

5

One (1) Floor Steamer

1

Product Description

3

4

2

11

1 - Steam Handle with Switch
2 - Locking Buttons
3 - Cord Winders
4 - Cleaning Hose Clamp
5 - Measuring Cup (pre-marked)
6 - Boiler Cap
7 - Steam Ready Indicator Light
(green)
8 - Power Indicator Light
(orange)
9 - Power Cord
10 - Steam Nozzles
11 - Extension Tube

9

12 - Funnel
13 - Carpet Slider Microfi ber Pad
14 - Carpet Glider
15 - Microfi ber Floor Pads
16 - Parking Pad

10

5

3

2

6

Technical Data
Adapter Input: 220-240V~50/60Hz

Cord Length: 7 meters/23 feet
Power: 1200 watts
Boiler: Stainless Steel
Boiler Capacity: 0.6 liter/20 ounces

7

8

12

14

15

16

13

PARKING PAD

6

Product Description

Product Description

1

4

7

2

5

8

3

6

9

ACCESSORIES

1 - Detail Nozzle
2 - Nylon Small Brushes
3 - Window Cleaner
4 - Small Brush Adapter
5 - Small Brush
6 - Fitted Microfi ber Pad for Small Brush
7 - Scraper
8 - Grout Brush
9 - Accessory Bag

Product Description

7

1 FLOOR STEAMER MODE

Assembly of Parts & Preparation of Steamer

Make sure all parts are in the box (see pg 6-7).

Before Use

IMPORTANT! FOLLOW THESE INSTRUCTIONS CAREFULLY.
WARNING! Always ensure steam switch is off and not

steaming when attaching an accessory to the unit.

A. Attach Handle to Steamer

Attention! The lower Extension Tube has the cord support pointing down.

The upper Extension Tube has the cord support pointing upwards.

• Insert the lower Extension Tube into the Floor Steamer
Base and press fi rmly in place (as shown in Fig. A).

• Insert the upper Extension Tube into the lower extension
tube and press fi rmly in place (as shown in Fig. B).

• Insert the Handle Extension Tube into the upper extension
tube and press fi rmly in place (as shown in Fig. C).

8

Before Use

B. Attach Cleaning Pads to Steamer
WARNING! To prevent fl oor damage, ALWAYS attach either the

Microfi ber Floor Pad or the Carpet Glide Accessory with Carpet
Pad when using your Floor Steamer. NEVER USE WITHOUT EITHER
OF THESE ATTACHMENTS AFFIXED TO THE MACHINE.

ATTACHING SCRUBBING FLOOR PAD
Scrubbing Floor Pad – Place Microfi ber Floor Pad

face down on the fl oor, wide side forward, with
center Scrub Strip facing down (and positioned to
match metal heat plate on bottom of Base-see “A”).
Hold Floor Steamer about 2” above Pad and gently
place Floor Steamer on the Pad. Firmly press down
to ensure Pad is adhered to the Floor Steamer.

A -

Heat Plate on
bottom of Base
boosts the cleaning
performance.

ATTACHING CARPET GLIDE WITH CARPET PAD

Place Carpet Glide face up on fl oor. Center and
place Carpet Pad on top of Carpet Glide. Hold
Floor Steamer over Carpet Glide and gently lower
the Steamer onto the Glide. Make sure the 4 clips
on Glide are around the outside of the Steamer
Base and using hands, attach the 4 clips of the
Carpet Glide to the Steamer Base.

Before Use

USE ON HARDWOOD FLOORS – For hardwood fl oors,
use only on “sealed” hardwood surfaces.
Move Steamer forward and backward while
cleaning, carefully observing the amount of steam
used, as too much water could cause damage.

*IMPORTANT NOTE ABOUT LINOLEUM FLOORING*

Steam can cause wax to be stripped from, and consequently damage, some
varieties of linoleum fl ooring. ALWAYS test a small, inconspicuous portion of the
fl oor BEFORE using steam to ensure that your linoleum fl oor does not have this
issue. For some varieties of linoleum or vinyl fl oors the fl oor steamer is harder to
push forward and back.

NOTE: See “Maintenance & Cleaning” for care and cleaning instructions for

Microfi ber Pads.

Before Use

9

C. Filling Boiler with Water
WARNINGS:

• Carefully read all instructions before removing Boiler Cap.

• Always unplug appliance before fi lling the Boiler.

Before Use

*IMPORTANT*

Use ordinary tap water. Distilled or demineralized water is recommended
if tap water is too hard. DO NOT add detergents, perfumes, oils, or other

chemical substances to the Boiler. The product warranty will be null and
void if anything other than water is added to the Boiler.

Follow these instructions to avoid overfi lling the Boiler:

• Be sure appliance is unplugged from the
electrical power outlet, and has cooled for

at least 5 minutes before fi lling with water.

• Make sure Handle Assembly is in the
upright “off” position. Remove Boiler Cap

by turning it counterclockwise.

200 ml

A

100 ml

N

B

I

T

(

x

M

a

• Pour in 600 mls of water using
the Measuring Cup and Filler
Funnel provided – fi ll cup to the
“200 ml” marking three times.

K

A

)

Be careful not to overfi ll the
Boiler. Please note that excess

200 ml

T

N

A

x

a

M

(

00 ml

1

water will be fl ushed out during
use if the Boiler is overfi lled,
resulting in wet fl oors.

10

• Replace Boiler Cap by turning it clockwise. Do not tighten
Boiler Cap too much – fi nger tightening is suffi cient to lock the
steam in the Boiler. If using cold water, heating time is about
3-5 minutes. If using warm water, heating time is reduced.

*IMPORTANT*

• Do not overfi ll the Boiler as excess water will be fl ushed out
of the Boiler before dry steam will emit.

• If re-fi lling the Boiler while Steamer has been in use, be sure
to allow Steamer to cool for at least 5 minutes and loosen
Boiler Cap slowly to allow any excess steam to escape
before completely removing Cap. (See page 12, “Refi lling
Boiler During Use” for detailed instructions.)

Before Use

2 Using Your Floor Steamer

A. Using the Parking Pad

You can use the Parking Pad if the Steamer is warm or hot.

CAUTIONS

The Parking Pad is provided to prevent fl oor
damage that can result from leaving a hot steamer
resting on the same spot for too long. ALWAYS
place Floor Steamer on the Parking Pad when not
in use, or while it is cooling before storage.

B. Starting the Appliance

• Be sure Boiler is fi lled with water and
Boiler Cap is securely in place.

• Insert the plug into a-3 prong grounded
electrical outlet (orange Power
Indicator Light will illuminate).

• Keeping the handle in the upright “Off”
position, wait until the (green) Steam
Ready Indicator Light illuminates.

Once Boiler is fi lled and the green Steam Ready Indicator Light
glows, Steamer is ready to clean the fl oors.

Using Your Floor Steamer

PARKING PAD

PLEASE NOTE: The green Steam Ready Indicator Light may turn on and off

C. Using Steam

• Press the button on the right

during use. This is normal and not a fault.

FRONT

side of the handle to unlock the
appliance.

• To emit steam from the underside
of the Steamer, press the FRONT
button on the handle.

You will fi nd that your Floor Steamer can easily
clean most hard surfaces and fl oors using the
steam from the underside alone.

NOTE: Some recondensed water may be emitted when the handle is fi rst pulled

down after fi lling. This is normal.

RIGHT

BUTTON

Using Your Floor Steamer

11

D. Using Steam (continued)

• To emit steam from the front
nozzles and the maximum
steam from the underside of
the steamer, press the REAR
button on the handle.

• IMPORTANT: at the end of
the cleaning task, press the
button on the left side to
lock the appliance in safety
mode.

Using Your Floor Steamer

*IMPORTANT*

The Steam Nozzles are meant to be used in steam “bursts” and should never be used
on a sustained basis. The Steam Nozzles will loosen especially diffi cult debris and will
assist in cleaning hard to reach areas such as fl oor edges.

NOTE: Your Steamer will not need refi lling for about 20-25 minutes

of usage.

The Floor Steamer will stop producing steam when the Boiler is
empty. When this happens unplug and store unit or refi ll with water
per instructions (below).

NOTE: If the Floor or Carpet Pad becomes too wet or too dirty,

replace with a clean, dry Pad and continue cleaning.

E. Refi lling Boiler During Use

When the Floor Steamer has run out of water, there will be no more
steam coming out of the unit. At this stage it is time to refi ll the Boiler.

Follow the refi lling instructions below.

*IMPORTANT*

The Floor Steamer has a Boiler that should not be overfi lled. To avoid the
potential for overfi lling, only refi ll the Boiler when it is completely run out of
water and only add 600ml. Always follow the practice of using the Floor
Steamer until it has run out of water and then refi ll 600ml only.

If fl oor cleaning is completed and water remains in the Boiler, the Floor
Steamer can be stored with the remaining water in the Boiler, there will be
no harm done to the unit. At the next cleaning session simply heat up the
unit and use the water already in the Boiler, then refi ll when empty.

Or alternatively at the next cleaning session, open the Boiler Cap when the
unit is still cold and pour out the water and then refi ll (if this alternative method
is used, it is recommended that only 500ml of water is added, because the
unit will not completely drain when the water is poured out from the Boiler).

12

Using Your Floor Steamer

WARNING: Let Steamer cool 5 minutes before opening Boiler Cap. Use

a

care when opening Boiler Cap as it may still be hot and steam may
escape, causing burns. If Boiler is still hot, water may spurt out during
refi lling which can also cause burns.

• Unplug the appliance from the electrical power outlet. This will stop

the Steamer from continuing to heat up.

• Slowly turn the Boiler Cap counterclockwise, ensuring that no
steam is present.

• Be sure Steamer has cooled 5 minutes before refi lling with water.

The product warranty will be null and void if
anything other than water is added to the
Boiler.

Using Your Floor Steamer

• Pour in 600 mls of water using the Measuring
Cup and Filler Funnel provided – fi ll the

200 ml

T

N

A

M

(

00 ml

1

Measuring Cup to the 200 ml marking 3
times. Be careful not to overfi ll the Boiler.

• Replace Boiler Cap by turning it clockwise.
Do not tighten Boiler Cap too much – fi nger
tightening is suffi cient to lock the steam in
the Boiler.

• Insert plug into 3-prong electrical outlet. Wait for green Steam
Ready Indicator Light to turn on. Steamer is ready to use once
again.

REMINDERS

• Always use ordinary tap water.

• If tap water is too hard, use distilled or demineralized water to avoid
the risk of mineral deposits and sediment from forming.

• Do not add detergents, perfumes, oils or other chemical substances to
the Boiler. This will damage the Steamer and void the warranty.

• The green Steam Ready Indicator Light may turn on and off during use.
This is normal and not a fault.

*IMPORTANT*

Do not overfi ll the Boiler as excess water will be fl ushed out of the Boiler
before dry steam will emit.

Using Your Floor Steamer

13

3 PORTABLE STEAM CLEANER MODE

Multipurpose Portable Steam Cleaner

The Hybrid Floor Steamer is a 2 in 1 model
that converts into a multipurpose portable
steam cleaner with just one click. The
portable steam cleaner features include:

1. Lightweight and portable unit.

2. Ergonomic steam handle for easy of use.

Cleaner Accessories

3. Versatile and quick change accessories.

4. On/off control.

5. Security locking button.

6. Cleans many areas such as bathrooms,
kitchens, pet areas and more.

14

Accessories - Attachment & Descriptions
A. Always use the Parking Pad
B. Attach Handle to Steamer

To use: Hold down the locking button on the

Steam handle while sliding it in an Extension
Tube. Be sure the locking button lines up with
the hole on the Extension Tube and button
locks in place.

To attach Extension Tubes together: Press
down the locking button while sliding Tubes
together. Be sure button and hole line up
and button locks in place.

To disconnect Extension Tubes: Press the
locking button and pull the two sections
apart.

Cleaner Accessories

C. Attach Extension Tube to Brush Adapter

Once the desired Brush is attached
to the Brush Adapter, press the
locking button on the Extension Tube
while sliding the Tube in the Brush
Adapter. Ensure the locking button
and the hole on the Brush Adapter
line up.

D. Attach Extension Tube or Steam Handle to Detail Nozzle

The Detail Nozzle provides a powerful
steam jet very useful for cleaning hard
to reach areas. It is ideal for blasting
dirt out of tight areas, cleaning door
and window tracks, shutters and
sanitary fi xtures.

To use: Slide and lock Detail Nozzle on
the Steam Handle or Extension Tube.

E. Attach Grout Brush to Detail Nozzle

The Grout Brush is designed to clean
the grout in between tiles. Use on fl oors
grouted, backsplashes and in showers.

To use: Push the Grout Brush on the
end of the Detail Nozzle.
(Detail Nozzle should be connected to
the Steam Handle or Extension Tubes.)

Cleaner Accessories

F. Attach Extension Tube or Steam Handle to Window Cleaner

The Window Cleaner is very useful for
cleaning large windows and glass.

To use: Connect Window Cleaner to
Steam Handle or Extension Tube(s) for
hard to reach surfaces. Apply steam
liberally, rub with soft spongy edge,
then remove excess water and dirt
with Window Cleaner Blade. Wipe dirt
from Window Cleaner blade.

CAUTION: When cleaning windows, always avoid any sudden changes
in temperature to prevent glass breakage or cracks.

Cleaner Accessories

15

G. Attach Nylon Detail Brush to Detail Nozzle

The Nylon Brush is used to help scrub
particularly tough dirt.

To use: Push the Nylon Brush on the
end of the Detail Nozzle. (Detail
Nozzle should be connected to the
Steam Handle or Extension Tubes.

H . Attach Scraper to Detail Nozzle

Cleaner Accessories

The Scraper is best for removing
small amounts of wallpaper and
also anything that can be scraped
from a fl at surface, e.g., grease
deposits in an oven. It is also useful
when defrosting freezers.

To use: Push the Scraper on the end of the Detail Nozzle. (Detail
Nozzle should be connected to the Steam Handle or Extension
Tubes.)

*CLICK

*CLICK

16

I. Connecting Brush Adapter to Small Brush

The Small Brush attaches either to
the extension tube(s) or the steam
handle and is used to clean smaller
areas that the Floor Steamer cannot
easily reach, such as corners of
fl oors, stairs and around furniture
legs.

To use: Attach Small Brush to Small Brush Adapter. Attach Extension
Tube or steam handle to Adapter by pressing the locking button
while sliding Tube or handle into Brush Adapter. Be sure button and
hole line up (see images “B” and “C” above) and button locks in
place.

180°

Cleaner Accessories

J. Attaching Microfi ber Pad to Small Brush

A fi tted Microfi ber Pad should be placed over the bristles of the
Small Brush to clean smooth surfaces such as kitchen cupboards,
splash backs, countertops, etc. Fit the Small Microfi ber Pad over
the Small Brush as shown below.

Steam Release

4

To release steam from the Steam
Handle, press the button on FRONT.
Steam will continue to be released
while the button is pressed.
To stop the steam, stop pressing the
button.

IMPORTANT: When the Steam Cleaner has run out of water, steam,

output will cease. Follow refi ll instructions (page 12) to use
your Steam Cleaner again.

FRONT

Cleaner Accessories

To move the steam cleaner
around simply grab the
base at the top of the arch
as shown in the image.

WARNING

While using the appliance
as a portable steam
cleaner, keep the arch
perpendicular (upright) to
the body of the appliance to
avoid the ejection of steam
from the front nozzles.

Cleaner Accessories

17

5

Turning Steam Cleaner Off

• To turn Steam Cleaner off, press the Power Switch and

unplug the electrical cord from the power outlet.

• Any remaining water can be left in the unit.

REMINDERS

• We recommend distilled or demineralised water as the best
way to care for and utilize your Steam Cleaner.

Using Your Floor Steamer

• If tap water is too hard, use distilled or demineralized water to
avoid the risk of staining pale colored fabrics.

• Do not add detergents, perfumes, oils or other chemical
substances.

6

Cleaning Steam Cleaner

We recommend you periodically clean the Steam Cleaner to
prevent the accumulation of calcium, mineral deposits and other
sediment caused by the use of tap water. After every 10-15 refi lls,
fi ll the Boiler three-quarters full of hot tap water, shake several
times and empty out the water into a sink.
Repeat several times to ensure that the Boiler is fl ushed of any
calcium or mineral deposits. Wipe the Steam Cleaner with a
damp cloth and dry.

NEVER HOLD THE STEAM CLEANER UNDER THE TAP TO FILL.
Use the fi lling cup provided to fi ll the Boiler.

Maintenance & Cleaning

If distilled or demineralised water is regularly used in the Steam
Cleaner, cleaning of the Boiler can be done less frequently.
In some areas tap water is very hard, it is recommended that
the Boiler is cleaned more frequently if hard water is used.

18

Using Your Floor Steamer - Maintenance & Cleaning

The cleaning of the Boiler and Steamer is the sole responsibility
of the appliance owner. Calcium, mineral deposits and other
sediments left to build up in the Steam Cleaner causing it to
fail and/or the steam pathways in the Steam Cleaner to block,
is not covered by the product warranty. Users must follow the
cleaning instructions above.

If the Steam Cleaner and Boiler is not cleaned according to
the instructions above and the product fails and/or the steam
pathways are blocked, the appliance owner should send the
product for servicing by contacting the Customer Support Line.

The Steam Cleaner is intended for domestic household use
only. It is not intended for commercial use. Any use other
than for domestic household purposes will void the product
warranty.

7

Replacement of Brushes, Microfi ber Pads
and Accessories

Maintenance & Cleaning

The Nylon Brushes and the fi tted Microfi ber Pad for the Small
Brush provided with the Steam Cleaner are to get you started
using your Steam Cleaner. As these brushes and microfi ber
pads become dirty or wear out, replacement brushes and
microfi ber pads can be purchased from the retailer from
which you purchased your Steam Cleaner and/or from most
other electrical appliance retail outlets.

It is normal to have replacements of the brushes and microfi ber
pads close at hand when doing cleaning as the brushes wear
out or the microfi ber pads become dirty.

Any of the other accessory tools are replaceable by
contacting the Customer Support Line.

Maintenance & Cleaning

19

8

Steam Cleaner Tips & Reminders

Steam cleaning allows the user to clean chemical-free by using
the power of steam, in place of harsh chemical-based cleaners.
The heat from the steam softens and loosens dirt on surfaces,
while the steam pressure lifts the dirt away. All that is left to do
is to wipe the surface to remove the dirt and moisture using a
cloth (preferably with a microfi ber cloth).

Tips & Reminders

TIP: to get the best cleaning results use a microfi ber cloth to
wipe the dirt and moisture from the surface being cleaned.
Microfi ber is designed to pick up and hold dirt, a great aid
in lifting and removing the dirt that the steam cleaner has
softened and loosened. Also, Microfi ber requires moisture to
glide over surfaces, the steam cleaner provides moisture that
the Microfi ber needs to glide. Microfi ber and Steam, a great
cleaning combination!

Making Contact with Surfaces

The steam is at its hottest just as it leaves the nozzle/accessory.
This is the area of the steam output that should be used to
clean to achieve maximum performance. All accessories
should make direct contact with the surfaces being cleaned
to transfer the heat from the Steam Cleaner to the surface in
order to soften and loosen dirt. If the accessory being used
does not make contact with the surface, the desired results
may not be achieved. If assistance is required contact our
Customer Support Line.

TIP: steam will clean hard, sealed, non-porous surfaces in
place of harsh chemical-based cleaners and detergents.
For soft furnishings such as carpets, rugs, lounges, children’s
toys etc, steam will refresh and deodorise the fi bres. Steam is
not used to clean carpets, other than to spot clean. To clean
carpets proper carpet cleaning equipment should be used.

20

Tips & Reminders

Water

Use ordinary tap water for all cleaning. In hard water areas,
we recommend distilled or demineralised water to reduce the
formation of calcium and other mineral deposits in the Steam
Cleaner. Use distilled or demineralised water when steaming light
coloured fabrics to eliminate the possibility of hard water stains.

IMPORTANT: Do not add cleaning solutions, perfumes, oils or
any other chemicals to the water used in the Boiler.

Temperature

The temperature in the stainless steel Boiler reaches about 130°C.
The steam temperature just outside the tip of the nozzle/accessory
is between 105°C and 115°C. The temperature of the steam falls
to 38°C at a distance of 25cm from nozzle. This Steam Cleaner
produces a drier steam which cools very rapidly to avoid burns
and injuries. Steam must make direct contact with surfaces for it
to clean effectively.

TIP: the hot steam can be used to kill dust mites in soft furnishings
and mattresses. The Steam Cleaner is ideal for asthma sufferers,
persons with skin sensitivities and anyone with chemical
sensitivities.

Tips & Reminders

Tips & Reminders

21

9

Microfi ber Pad Care & Cleaning

Your Microfi ber Pads are designed for hundreds of uses. Clean
Pads regularly, either by hand washing (using mild soap
and warm water) or in your clothes washer on a delicate
cycle, cool water. Never use fabric softener or bleach. We
recommend letting Pads air dry to maintain maximum long
term effectiveness.

Replacement pads are available at most retail outlets or on
our website at www.eurofl ex.com.au.

Microfi ber washing instructions – ULTRA MICROFIBER

Maintenance & Cleaning

MICROFIBER FLOOR PAD

50% Polyester / 50% Polyamide

Hand wash only
Tumble dry low or air dry
No bleach / No fabric so ener

CARPET PAD

80% Polyester / 20% Polyamide

Hand wash only
Tumble dry low or air dry
No bleach / No fabric so ener

22

Maintenance & Cleaning

Troubleshooting

10

ISSUES POSSIBLE CAUSES SOLUTIONS

Steam is not coming out of
the Steam Nozzles

The Hard Surface Floor Pad
is not adhering to Steamer

The Cleaning Pads are
ge ng soaked (too wet).
Why?

The steam seems to be
making my fl oor too wet

Improper Handle Assembly Call Customer Service to receive instruc ons to correct

Not enough pressure was
applied when a aching Pad

Floor Pad requires replacing
due to age of the Floor Pad

Boiler is overfi lled Let Steamer run un l excess water ceases. -OR- Remove

Green “Steam Ready Indica­tor Light” is not illuminated

Front Steam Jets are being
used too frequently

The Cleaning Pad is too wet
(saturated with moisture)

the problem

Posi on Steamer about 2” above Pad and FIRMLY press
it down onto the Pad

Replacement Floor Pads can be purchased at most
electrical appliance retail outlets

some water from Boiler once the Boiler has cooled
down completely

Wait for green “Steam Ready Indicator Light” to
illuminate

Only use Front Steam Jets in short bursts for cleaning
tougher dirt or to clean hard to reach areas

Replace the wet Pad with a dry, clean Pad and con nue
cleaning

IMPORTANT QUESTION:
Q: Do I always need to use a Microfi ber Pad when cleaning with

my Floor Steamer?
A. YES! It is critically important to ALWAYS use your Microfi ber

Pads. The Floor Steamer should NEVER be used without either a
Hard Surface Floor Pad or Carpet Glide with Carpet Pad.

Troubleshooting

Troubleshooting

23

Customer Support

Customers needing assistance with their Floor Steamer can call the Customer Support Line on
the phone numbers listed below. Customers should also call the Customer Support Line if they
require product arranty repair or post-warranty product servicing.Our friendly Customer Service
Team can assist you with getting the best cleaning results from your Floor Steamer, they are full

of helpful steam cleaning tips, too.

Customer Support Line

AUSTRALIA 1800 663 866

NEW ZEALAND 0800 666 783

Euroflex Australia Pty Ltd

79 Furniss Road

DARCH WA 6065

AUSTRALIA

TEL: [phone]
Email: [e-mail]
Website: www.euroflex.com.au

Euroflex New Zealand Ltd

c/- Dubins

137 Glenfield Road

Birkenhead Auckland 0626

NEW ZEALAND

TEL: [phone]
Email: [e-mail]
Website: www.euroflex.com.au

Plastecs SRL

Via dei Colli, 59

31058 Susegana (TV)

ITALY

Tel: [phone]

Email: [e-mail]

Website: www.euroflex-appliances.com

SC1M1 04/2019