Page 1
IEZ / ITZV4
Micro-ATX Intel 810E
Micro-ATX Intel 810
Socket 370 Motherboard
User’s Guide
Model : IEZ / ITZV4
Manual Version : English, version 1.0
Release Date : JAN 14, 2000
Page 2
CopyrightCopyright
Copyright
CopyrightCopyright
Copyright 2000 by this company. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in
a retrieval system or translated into any language in any form or by any means,
electronic, mechanical, magnetic, optical, manual or otherwise, without the prior
written consent of the copyright holders.
The contents of this publication are subject to change. This company reserves
the right to alter the contents of this publication at any time and without notice.
The contents of this publication may contain inaccuracies or typographical errors
and is supplied for informational use only.
Intel and Pentium are registered trademarks of Intel Corporation.
OS/2 and IBM are registered trademarks of Intemational Business Machines.
c
UserUser
¯¯
¯s
¯¯
Notice Notice
Notice
Notice Notice
User
UserUser
Windows and MS-DOS are registered trademarks of Microsoft Corporation.
AWARD is a registered trademark of Award Software Inc.
Other brand, corporate, and product names may or may not be registered trademarks
or copyright of their respective companies.
Page 3
FCC & DOC Compliance
Federal communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following
two conditions:
! This device may not cause harmful interference.
! This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generatesm uses and can radiate radio frequency
energy and, if not installed and used in accordance with the manufacturer’s
instructions, may cause harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
! Re-orient or relocate the receiving antenna.
! Increase the separation between the equipment and the receiver.
! Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
! Consult the dealer or an experienced radio/TV technician for help.
Warning! The use of shielded cables for the connection of the monitor to
the graphics card is required to assure compliance with FCC regulations
Changes or modifications to this authority to operate this equipment.
Page 4
CONTENTS
General Description
Manual Features / Package Check List........................................................I
SECTION 1: PRODUCT INFORMATION
1-1 Mainboard Specifications..............................................................1-2
1-2 Mainboard Layout..........................................................................1-3
SECTION 2: HARDWARE INSTALLATION
2-1 Jumper Settings.............................................................................2-1
2-2 Connectors....................................................................................2-3
2-3 Game / Audio Connector...........................................................2-7
2-4 System Memory Installation................................................................2-8
SECTION 3: CMOS SETUP UTILITY
3-1 BIOS Setup Main Menu.....................................................................3-1
3-2 Standard CMOS Setup......................................................................3-2
3-3 Adcanced BIOS Features.........................................................................3-4
3-4 Advanced Chipset Features .............................................................3-8
3-5 Integrated Peripherals................................................................3-11
3-6 Power Management Setup........................................................... 3-15
3-7 PnP/PCI Configurations.......................................................3-18
3-8 PC Health Status......................................................................... 3-19
3-9 Frequency/Voltage Control.............................................................. 3-19
3-10 Load Fail-Safe Defaults.....................................................................3-21
3-11 Load Optimized Defaults..............................................................3-21
3-12 Set Supervisor/Use Password.....................................................3-22
3-13 Save & Exit Setup...................................................................3-22
3-14 Exit Without Saving...........................................................................3-22
SECTION 4: SOFTWARE UTILITY
4-1 VIA V x D Setup Program.....................................................................4-1
4-2 VIA Audio Setup Program...................................................................4-1
4-3 VIA Chipset Driver Setup Program........................................................4-2
4-4 VIA Hardware Monitor System V1.05....................................................4-2
Page 5
General DescriptionGeneral Description
General Description
General DescriptionGeneral Description
Thanks for purchasing
chipset (North Bridge FW82810E & South Bridge FW82801AA). The 810E chipset provides
stability and value with Intel graphics performance and smart integration.
is Intel 810(North Bridge FW82810 & South Bridge FW82801AA). It is a highly integrated
chipset designed for the basic graphics / multimedia PC platform.
provide you perfect function to be the same with your system operation and end user.
This user’s manual contains all the information and features that show you how to use
IEZ / ITZV4 IEZ / ITZV4
the
IEZ / ITZV4 motherboard. Please take a moment to familiarize yourself with the design
IEZ / ITZV4 IEZ / ITZV4
and organization of this manual.
Manual FeaturesManual Features
Manual Features
Manual FeaturesManual Features
This manual is divided into the following four sections:
Section 1: Product InformationSection 1: Product Information
Section 1: Product Information
Section 1: Product InformationSection 1: Product Information
A brief overview of what comes in the mainboard package, the mainboard layout an the
specification it appears.
Section 2: Hardware InstallationSection 2: Hardware Installation
Section 2: Hardware Installation
Section 2: Hardware InstallationSection 2: Hardware Installation
IEZ / ITZV4 Socket 370 IEZ / ITZV4 Socket 370
IEZ / ITZV4 Socket 370 mainboard.
IEZ / ITZV4 Socket 370 IEZ / ITZV4 Socket 370
IEZ IEZ
IEZ is
IEZ IEZ
based on Intel 810E
ITZV4ITZV4
ITZV4 chipset
ITZV4ITZV4
IEZ / ITZV4IEZ / ITZV4
IEZ / ITZV4
IEZ / ITZV4IEZ / ITZV4
T ell you the usage of the mainboard jumpers and the connectors.
Section 3: CMOS Setup UtilitySection 3: CMOS Setup Utility
Section 3: CMOS Setup Utility
Section 3: CMOS Setup UtilitySection 3: CMOS Setup Utility
A summary of the mainboard CMOS (BIOS) Setting.
Section 4: BIOS / Software UtilitySection 4: BIOS / Software Utility
Section 4: BIOS / Software Utility
Section 4: BIOS / Software UtilitySection 4: BIOS / Software Utility
Introduction of some useful mainboard BIOS / Software utility .
Package Check ListPackage Check List
Package Check List
Package Check ListPackage Check List
IEZ / ITZV4 IEZ / ITZV4
This
IEZ / ITZV4 mainboard package contains the following items. Please inspect the
IEZ / ITZV4 IEZ / ITZV4
package contents and confirm that every thing is there. If anything is missing or damaged,
call your vendor for instructions before operating.
The Package includes:
! One
! One Floppy Interface Cable
! One IDE Interface Cable
! One Motherboard Resource CD
IEZ / ITZV4 IEZ / ITZV4
IEZ / ITZV4 mainboard
IEZ / ITZV4 IEZ / ITZV4
IEZ / ITZV4 Motherboard User’s Manual
I
Page 6
I Product Information
SECTION 1
Product InformaProduct Information
Product Information
P
1-1 Mainboard Specifications
Form Factor Micro ATX form fac tor
Boa rd Siz e 24.4c m x 19.0cm
Supports Socket 370 CPU--Celeron(PPGA) & Coppermine(FC-PGA)
CPU
System Me mory DIMM 16 8-pi n x 2 , SD RAM ma xim um 512MB
Chipset
Expansion Slots
Seri al Port Two seri al p or ts U ATR 1655 0 c omp ati ble
Para lle l Por t
Floppy In terfa ce
Ide Int erfa ce
USB Port
PS/2 M ou se PS/2 m ou se s up ported by c onn ec tor o nbo ard
PS/2 Keyboard PS/2 Ke yb oar d sup po r ted b y c on nec tor o nbo ar d
Sou nd Fu nc tio n ON-I CH A ud io Codec AC'9 7
Fuse Support Recoverable fuse for USB,KB & MOUSE
RTC and B a tter y
Power Connector ATX
Wake up F unc tio n
Hardware Monitor
BIOS
LED In dic at o r
Sup port s FS B 66 . 8/7 3/1 00/103/118/ 12 4/13 3/137/140 / 15 0MHz
Supports CPU type/clock by jumperless BIOS set up
Int el 8 10 / 810 E Chips ets incl udi ng:
-Intel 82810(ITZV4) / Intel 82810E(IEZ)--GMCH
-In tel 8 280 1A A IC H
-In tel 8 280 2A B FW H
3 x PC I sl ots
1 x IS A sl ot
1 x AMR c onn ect or fo r MC '97
One p arallel port suppo rt s:
-SPP-standard parallel port
-EPP-enhanced parallel port
-ECP -ext emd ed capabi lit ies po r t
Suppor t dr iv ers inc he s/f o rma t w ith:
-3. 5 in che s-7 20K B/1.44MB/ 2 .88M B
-5. 25 i nch es -360KB/1.2 MB
Dual Ide Int e rfac e s upport 4 x IDE HD D or CDRO M
Support PIO Mode 4, ULTRA DMA/33 & ULTRA DM A/66
Two USB po r ts sup ported
Sup port USB L ega cy Keyb oar d fun cti on
Built in IC H
Lithium(CR- 20 32) b at te ry
LAN wake up
RTC Alarm wake up
3 Fan s peed Moni tor
4 Po si tiv e Voltage Inputs , 2 intrinsic vol tag e mo nitoring
Over t emp er a tur e i ndi ca te o ut pu t
Auto ma tic Pow er on volta ge d et ec ti on b eep
Award BIOS
Supports APM, DMI and ACPI
Sup port s S TR( Sus pen d To RAM)
Supports virus warni ng
Sup port s Flash / U pgra de B I OS fu nctions
System Power LED
HDD acti vity L ED
System S us pen d L ED
IEZ / ITZV4 Motherboard User’s Manual
1-1
Page 7
I Product Information
1-21-2
1-2
1-21-2
Motherboard LayoutMotherboard Layout
Motherboard Layout
Motherboard LayoutMotherboard Layout
JumpersJumpers
Jumpers
JumpersJumpers
1. JP2 CPU Clock Frequency
2. JP 1 Clear CMOS
3. CON13 COM2
4. CON16 IrDA
5. CON11, CON12 CD_IN
IEZ / ITZV4 Motherboard User’s Manual
1-2
Page 8
I Product Information
Expansion SocketsExpansion Sockets
Expansion Sockets
Expansion SocketsExpansion Sockets
1. DIMM 1 Support 168-pin DIMM Memory
2. DIMM 2 Support 168-pin DIMM Memory
Expansion SlotsExpansion Slots
Expansion Slots
Expansion SlotsExpansion Slots
1. C PU Socket 370 CPU
2. PCI slot1 to slot3 32-bit PCI Bus Expansion slot
3. ISA slot ISA Bust Expansion slot
3. AMR AMR Expansion Slot for MC97 Devices
ConnectorsConnectors
Connectors
ConnectorsConnectors
1. IDE 1 Primary IDE Connector
2. IDE 2 Secondary IDE Connector
3. Floppy Floppy Drive Connector
4. Panel - PowerOn ATX Power on
- Reset Reset Swithch Connector
- HDD Led HDD Led Connector
- Power Led ATX Power Led Connector
- Speaker Chassis Speaker Connector
- KEYLOCK Keyboard Lock Switch Connector
5. Sys Fan System Fan Connector
6. CPU Fan CPU Fan Connector
7. ATX Power ATX Power Connector
8. COM2 COM2 Connector
9. CD Audio CD-IN Connector
10. Joystick Game / Audio Connector
11. Printer Ptinter (Parallel) Port Connector
12. USB Universal Serial Bus Port1 and Port2
13. PS/2 Mouse PS/2 Mouse & Keyboard Connectors
IEZ / ITZV4 Motherboard User’s Manual
1-3
Page 9
SECTON 2
HARDWARE INSTALLATION
This section gives you a step-by step procedure on how to install your system. Follow each
section accordingly.
2- 1 Jumper Settings
Please refer the following figures for the locations of the jumpers on the mainboard.
2-1.1 CMOS Clear Setting
JP1 Clear CMOS
Clear CMOS
To clear CMOS,please follow the steps below:
1. Power off the system and unplug the chassis AC power cord.
2. Short JP1 at pin 2-3 for few seconds.
3. Set JP1 back to its Normal position at pin 1-2.
4. Plug the AC power cord to the chassis.
5. Power on the system and load the BIOS setup default.
Normal
(Default)
IEZ / ITZV4 Motherboard User’s Manual
2-1
Page 10
II. HARDWARE INSTALLATION
2-1.2 CPU Type Setting
Static Precautions
Static electricity can be a serious damage to the electronic components on this mainboard.
To avoid damage caused by electrostatic discharge, observe the following precautions:
- Don’t removes the motherboard from its anti-static packaging until you are ready to
install it into a computer case.
- Before you handle the motherboard in any way, touch a grounded, antistatic surface,
such as an unpainted portion of the system chassis, for a few seconds to discharge
any built-up static electricity.
- Handle add-in cards and modules by the edges or mounting bracket.
CPU Setting
After installing the CPU, you must set the clock selection jumpers to match the frequency of
the CPU. Find the jumpers labeled JP2 set the jumpers (from 1 to 8 jumpers, we call them as
FS0, FS1, FS2 and FS3) according to the figure below and table for CPU frequency. JP2’ s
jumpers from 9 to 12 (we call them as FS4 and FS5) are used for over-clock, we also
recommend them to users.
""
"
""
CPU Frequency
FS5
FS4
FS3
FS2
FS1
FS0
IEZ / ITZV4 Motherboard User’s Manual
2-2
Page 11
II. HARDWARE INSTALLATION
Remarks:
This motherboard belongs to jumperless and its Clock Ratio has been Set in
the BIOS. If the user need to change any ratio, please reset in the BIOS.
!!
!
!!
Clock Frequency:
FS3 FS2 FS1 FS0
CPU
(MHz)
PCICL K
(MHz)
Short Short Short Short 66.80 33.40
Short Short Short Open 68.00 34.00
Short Short Open Short 100.30 33.43
Short Short Open Open 103.00 34.33
Short Open Short Short 133.73 33.43
Short Open Short Open 145.00 36.25
Short Open Open Short 133.73 33.43
Short Open Open Open 137.33 34.33
Open Short Short Short 140.00 35.00
Open Short Short Open 140.00 46.67
Open Short Open Short 118.00 39.33
Open Short Open Open 124.00 41.33
Open Open Short Short 133.70 44.57
"!"!
"!
"!"!
Open Open Short Open 137.00 45.67
Open Open Open Short 150.00 37.50
Open Open Open Open 72.50 36.25
OVER-CLOCK Select :OVER-CLOCK Select :
OVER-CLOCK Select :
OVER-CLOCK Select :OVER-CLOCK Select :
JP2
FS5
FS4
I
IEZ / ITZV4 Motherboard User’s Manual
JP2
JP2 FS4 FS5 FREQUENCY
JP2-I SHORT OPEN 66/100
JP2-II OPEN SHORT 100/133
II
2-3
Page 12
II. HARDWARE INSTALLATION
2-2 Connectors
2-2.1 Panel Connector
- PWR LED
- SPEAKER
- KEY LOCK
- HDD LED
- RESET
- PWR ON
2-2.2 Power Connector
Connect the 20-pin ATX power supply cable to this power connector. Make sure the
right plug-in direction and the power supply is off before connecting or disconnecting
the power cable.
Remark: We suggest that users use 5 V STB and power source current
should be over 0.7A, otherwise it will affect system boot up.
ATX Power LED Connector (3 pins)
Chassis Speaker Connector (4 pins)
Key Lock Connector (2 pins)
HDD LED Connector (2 pins)
Reset Switch Connector (2 pins)
ATX Power Switch Connector (2 pins)
ATX Power Connector
IEZ / ITZV4 Motherboard User’s Manual
2-4
Page 13
II. HARDWARE INSTALLATION
2-2.3 Fan Connector
Connect the CPU and System fan cables to the fan connectors shown below.
The fan connectors are marked as: SYS FAN & CPU FAN on the motherboad.
2-2.4 PS/2 Mouse and Keyboard Connectors
Connect the PS/2 mouse and keyboard to the onboard 6-pin Mini-Din connector
shown as below.
PS/2 Mouse
PS/2 Keyboard
2-2.5 USB Device Connector
Connect your USB device(s) to the onboard USB connector shown as below.
Top: USB1
Bottom: USB2
IEZ / ITZV4 Motherboard User’s Manual
2-5
Page 14
II. HARDWARE INSTALLATION
2-2.6 Serial Device (COM1/COM2), VGA and Printer Connectors
Connector your serial device(s) to the onboard serial connectors marked as COM1
and COM2. Connect the 15-pins VGA Monitor Output marked as VGA to your system
monitor or other VGA compatible devices. Connect your local printer to the onboard
25-pin printer connector marked shown as below.
COM2
PRINTER
COM1 VGA
2-2.7 Floppy Drive Connector
Connect the floppy drive cable to the onboard 34-pin floppy drive connector marked
as FDD.
FDD
2-2.8 IrDA Connector
Connect your IR devices to the onboard IrDA connectors shown as below.
1
2
3
4
5
IR
Pin Description
1 +5V
2NC
3 IRRX
4 GND
5 IRTX
IEZ / ITZV4 Motherboard User’s Manual
2-6
Page 15
II. HARDWARE INSTALLATION
2-2.9 IDE Hard Disk Connector
Connect your IDE devices to the onboard 40-pin IDE connectors marked as IDE1 and
IDE2.
IDE 1
2 40
1 39
IDE 2
2 40
1 39
SECONDARY IDE
2 40
1 39
PRIMARY IDE
2 40
1 39
It is suggested that you connect the IDE devices to your IDE cables as the figure shown
above. Each IDE channel, either Primary or Secondary, supports two IDE devices which
must be set differently to master mode and slave mode.
2-3 Game / Audio Connector and CD IN Connectors
Connect the game device onboard marked as JOYSTICK. CD connectors onboard
marked as CD IN are for CD-ROM connector and.
JOYSTICK
Line
Line
out
in
Mic in
CD IN
CON 11/CON 12
IEZ / ITZV4 Motherboard User’s Manual
2-7
Page 16
II. HARDWARE INSTALLATION
2-4 System Memory Installation
There are 2 pieces 168-pin DIMM (Dual Inline Memory Module) sockets on the
mainboard which support SDRAM and EDO DRAM memory.
There are 2x168-pin DIMM slots
(DIMM1, DIMM2) that allow you to
install the system memory max
up to 512MB SDRAM.
♦ To ensure reliability, it is recommended to use PC 100 SDRAM or PC 133 SDRAM
for your high clock SDRAM performance requirement.
♦ If you are using low clock SDRAMs, you should set the SDRAM clock option of
the BIOS’s Chipset Feature Setup to HCLK-33 to ensure stability.
♦ DIMM Sizes supported:
♦ T otal Memory Size = DIMM1 + DIMM2, maximum up to 512MB.
8MB, 16MB, 32MB, 64MB, 128MB.8MB, 16MB, 32MB, 64MB, 128MB.
8MB, 16MB, 32MB, 64MB, 128MB.
8MB, 16MB, 32MB, 64MB, 128MB, 256MB.8MB, 16MB, 32MB, 64MB, 128MB.
IEZ / ITZV4 Motherboard User’s Manual
2-8
Page 17
III CMOS SETUP UTILITY
SECTION 3
CMOS SETUP UTILITY
The rest of this manual is intended to guide you through the process of configuring your system
using Setup.While the BIOS is in control, the Setup program can be activated by pressing the
<Del>key during the POST (Power On Self-Test).If the message disappears before you respond
and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or
pressing the “RESET” button on the system case. You may also restart by simultaneously
pressing <Ctrl>, <Alt>, and <Delete> keys.
3-1 BIOS Setup Main Menu
Once you enter the BIOS setup utility, the Main Menu will appear on the screen. The Main Menu
allows you to select from several setup functions . the arrow keys to select among the items
and press <Enter> to accept and enter the submenu.
CMOS Setup Utility - Copyright ( C ) 1984-2000 Award Software
!
Standard CMOS Features
!
Frequency/Voltage Control
!
Advanced BIOS Features Load Fail -Safe Defaults
!
Advanced Chipset Features Load Optimized Defaults
!
Integrated Peripherals Set Supervisor Password
!
Power Management Setup Set User Password
!
PnP/PCI Configurations Save & Exit Setup
!
PC Health Status Exit Without Saving
Esc : Quit ↑ ↓ ← → : Select Item
F10 : Save & Exit Setup
Abandon all Datas
The main menu includes the following main setup categories, which defines basic information
about your system. Below are the keyboard function keys you can use under the menu.
Menu function keys:
↑↑
↓↓
←→←→
↑
↓
←→
↑↑
↓↓
←→←→
: To Move around the screen. An item is highlighted if it is selected.
: General Help on setup.
F1
: Save CMOS Changes & Exit.
: To select or enter a submenu.
F10
ENTER
: Main Menu: quit without saving changes.
ESC
IEZ / ITZV4 Motherboard User’s Manual
3-1
Page 18
III CMOS SETUP UTILITY
3-2 Standard CMOS Setup
The items in Standard CMOS Setup Menu are divided into 10 categories. Each category
includes none, one or more than one setup items. Use the arrow keys to highlight the item and
then use the / <PgUp> / <PgDn> keys to select the value you want in each item.
↑ ↓ ← →
Standard CMOS Features
Date (mm : dd : yy):
Time (hh : mm: ss):
!
IDE Primary Master
!
IDE Primary Slave
!
IDE Secondary Master
!
IDE Secondary Slave
Drive A
Drive B
Video
Halt On
Base Memory
Extended Memory
Total Memory
↑↓← →
Move Enter: Select +/-/PU/PD: Value F10:Save E SC: Exit F1:General Help
F5:Previous Values F6:Fail-safe defaults F7:Optimized Defaults
""
" Date & Time
""
To set the date and time, highlight the date area.Press/<PgUp>/<PgDn>
to set the current date. The date format is month: Jan. ~ Dec; date: 1 ~ 31; year:
1994 ~ 2079; hour: 00 ~ 23; and second: 00 ~ 59.
" IDE Primary Master
" IDE Primary Slave
"
IDE Secondary MasterIDE Secondary Master
IDE Secondary Master
IDE Secondary MasterIDE Secondary Master
" IDE Secondary Slave
Mon, Feb 8 1999
16:19:20
Press Enter None
Press Enter None
Press Enter None
Press Enter None
1.44M, 3.5 in.
None
EGA/VGA
All, But Keyboard
640K
30720K
31744K
Item Help
Me nu Level
Change the day, month,
year and century
!
↑ ↓ ← →
Press <Enter> to enter the submenu of detailed options, the following table shows
the IDE primary master submenu.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
IDE Primary Maste r
IDE HDD Aut o-Detection
ID E Primary Ma s ter
Access Mod e
Capacity
Cylinder
Head
Precomp
Landi ng Zone
Sector
↑↓←→
Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe defaults F7:Optimized Defaults
IEZ / ITZV4 Motherboard User’s Manual
Press Enter
Auto
Auto
0 MB
0
0
0
0
0
3-2
Item Help
Menu Level
To au to-detect the HDD's size,
head… on this c hannel
!!
Page 19
III CMOS SETUP UTILITY
""
" IDE HDD Auto-detection
""
IDE HDD Auto-detection: Press enter to auto - detect the HDD on the channel.
" IDE Primary Master
IDE Primary Master: Selecting ‘manual’ lets you set the remaining fields on
- None the screen. Selects the type of fixed disk. “User Type”
- Auto will let you select the number of cylinders, heads, etc.
- Manual Note: PRECOMP=65535 means NONE!
" Access Mode
Access Mode: Choose the access mode for this hard disk.
- Normal
- LBA
- Large
- Auto Default: Auto
If detection is successful, it fills the remaining feilds
on the menu.
Default: Auto
"
CapacityCapacity
Capacity
CapacityCapacity
Capacity:Capacity:
Capacity: Disk drive capacity (approximated). Note that this size
Capacity:Capacity:
- Auto display your is usually slightly greater thanthe size of the formatted
drive size disk given by a disk checking program.
The following options are selectable only
item is set to 'Manual' and Access Mode is set to "Normal":
Cylinder
Head
Precomp
Landing zone
Sector
Min = 0
Max = 65535
Min = 0
Max = 255
Min = 0
Max = 65535
Min = 0
Max = 65535
Min = 0
Max = 255
if the 'IDE Primary Master'
Set the number of cylinders for this
ha rd di sk.
Set the number of read/write heads
Warning: Setting a value of 65535
me an s n o ha rd d i sk
Number of sectors per track
IEZ / ITZV4 Motherboard User’s Manual
3-3
Page 20
III CMOS SETUP UTILITY
""
"
""
Drive A / Drive BDrive A / Drive B
Drive A / Drive B
Drive A / Drive BDrive A / Drive B
Drive A / B: Select the floppy drive type installed in your system. The
- None available options for Drive A and Drive B are: 360KB 5.25”,
- 360KB 5.25” 1.2MB 5.25”, 720KB 3.5” 1.44MB 3.5”, 2.88MB 3.5” and
- 1.2MB 5.25” NONE.
- 720KB 3.5”
- 1.44MB 3.5” Default: Drive A 1.44MB 3.5
- 2.88MB 3.5” Drive B None
""
"
""
VideoVideo
Video
VideoVideo
Video:Video:
Video: Select the video display card type installed in your system.
Video:Video:
- EGA / VGA The available types are: EGA/VGA, CGA 40, CGA80 and
- CGA40 Mono.
- CGA80
- Mono
""
"
""
Halt OnHalt On
Halt On
Halt OnHalt On
Default: EGA/VGADefault: EGA/VGA
Default: EGA/VGA
Default: EGA/VGADefault: EGA/VGA
Halt On: This item defines the operation of the system POST (Power
- All Errors On Self-Test). You can use this item to select which kind of
- No Errors errors will cause the system to halt during POST.
- All, But keyboard
- All, But Diskette
- All, But Disk / Key Default: All, But Keyboard
3-3 Advanced BIOS Features
This section allows you to configure your system for basic operation.
CMOS Setup Utility – Copyright © 1984 – 2000 Award Software
Virus Warning Enabled
CPU Internal Cache Enabled
External Cache Enabled
CPU L2 Cache ECC Checking Enabled
Quick Power O n S elf Test Disabled
First Boot device Floppy
Second Boot device HDD-0
Third Boot device LS/ZIP
Boot other device Enabled
Swap Floppy Drive Disabled
Boot Up Floppy Seek Enabled
Boot Up NumLock Status Off
Gate A20 Option Fast
Type matic Rate Settin g Disa ble d
Typematic Rate (Chars/Sec) 6
Typematic Delay (Msec) 25 0
Security Option Setup
OS Se lec t For DRAM > 64MB Non - O S2
Report No FDD For WIN 95 No
↑↓←→
Move Enter: Select +/-/PU/PD: Value F10:Save ES C: Exit F1:General Help
F5:Previous Values F6:Fail-safe defaults F7:Optimized Defaults
Advanced BIOS Features
IEZ / ITZV4 Motherboard User’s Manual
3-4
Item Help
Menu Level
Allows you to choose the VIRUS
warning feature for IDE Hard Disk
boot sector protection. If this
function is enabled and someone
attempt to write data into this area,
BIOS will show a warning m essage
on screen and alarm beep
!
Page 21
III CMOS SETUP UTILITY
!!
! Virus Warning
!!
Virus Warning: If this function enabled and someone attempt to write
- Enabled data into this area, BIOS will automatically show a
- Disabled warming message on screen and alarm beep.
!!
! CPU internal / external cache
!!
CPU internal / external cache: These two items controls Enable / Disable the
- Enabled CPU internal / external cache.
- Disabled
!!
! CPU L2 Cache ECC Checking
!!
CPU L2 Cache ECC Checking: This item allows you to enable / disable CPU
- Enabled L2 Cache ECC Checking.
- Disabled
Default: Disabled
Default: Enabled
Default: Enabled
!!
! Quick Power On Self Test
!!
Quick Power On Self Test: This item speeds up Power On Self Test
- Enabled (POST) after you power up the computer.
- Disabled If it is set to Enable, BIOS will shorten or
skip some check items during POST.
Default: Disabled
!!
!
!!
First / Second / Third / Boot Other DeviceFirst / Second / Third / Boot Other Device
First / Second / Third / Boot Other Device
First / Second / Third / Boot Other DeviceFirst / Second / Third / Boot Other Device
First / Second / Third / Boot Other Device:First / Second / Third / Boot Other Device:
First / Second / Third / Boot Other Device:
First / Second / Third / Boot Other Device:First / Second / Third / Boot Other Device:
- Floppy The BIOS attempts to load the operating
- LS / ZIP system from the devices in the sequence
- HDD-0/1/2/3 selected in these items.
- SCSI
- CDROM
--
- LAN
--
Default: Default:
Default:
Default: Default:
- Disabled
- Enabled
!!
!
!!
Swap Floppy DriveSwap Floppy Drive
Swap Floppy Drive
Swap Floppy DriveSwap Floppy Drive
Swap Floppy Drive:Swap Floppy Drive:
Swap Floppy Drive: If the system has two floppy drives, choose
Swap Floppy Drive:Swap Floppy Drive:
FirstFirst
""
First
"
FirstFirst
""
SecondSecond
Second
SecondSecond
ThirdThird
""
Third
"
ThirdThird
""
OtherOther
""
Other
"
OtherOther
""
floppyfloppy
floppy
floppyfloppy
""
HDD-O,HDD-O,
"
HDD-O,
""
HDD-O,HDD-O,
LS/ZIPLS/ZIP
LS/ZIP
LS/ZIPLS/ZIP
EnabledEnabled
Enabled
EnabledEnabled
,,
,
,,
,,
,
,,
- Enabled enable to assign physical drive B to logical
- Disabled drive A and vice-versa.
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
IEZ / ITZV4 Motherboard User’s Manual
3-5
Page 22
III CMOS SETUP UTILITY
""
"
""
Boot Up Floppy SeekBoot Up Floppy Seek
Boot Up Floppy Seek
Boot Up Floppy SeekBoot Up Floppy Seek
Boot Up Floppy Seek:Boot Up Floppy Seek:
Boot Up Floppy Seek: Seeks disk drives during boot up.
Boot Up Floppy Seek:Boot Up Floppy Seek:
- Enabled
- Disabled
Default: EnabledDefault: Enabled
Default: Enabled
Default: EnabledDefault: Enabled
""
"
""
Boot Up NumLock StatusBoot Up NumLock Status
Boot Up NumLock Status
Boot Up NumLock StatusBoot Up NumLock Status
Boot Up NumLock Status:Boot Up NumLock Status:
Boot Up NumLock Status: Selects power on state for NumLock.
Boot Up NumLock Status:Boot Up NumLock Status:
- Off
-On
Default: offDefault: off
Default: off
Default: offDefault: off
""
"
""
Gate A20 OptionGate A20 Option
Gate A20 Option
Gate A20 OptionGate A20 Option
Gate A20 Option:Gate A20 Option:
Gate A20 Option: Normal-a pin in the keyboard controller controls
Gate A20 Option:Gate A20 Option:
- Normal Gate A20. Fast-lets chipset control Gate A20
- Fast
Default: FastDefault: Fast
Default: Fast
Default: FastDefault: Fast
""
"
""
TT
ypematic Rate Settingypematic Rate Setting
T
ypematic Rate Setting
TT
ypematic Rate Settingypematic Rate Setting
TT
ypematic Rate Setting:ypematic Rate Setting:
T
ypematic Rate Setting: Keystrokes repeat at a rate determined by the
TT
ypematic Rate Setting:ypematic Rate Setting:
- Enabled keyboard controller, when enabled, the
- Disabled typematic rate and typematic delay can be
selected.
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
""
"
""
TT
ypematic Rate (Chars/Sec)ypematic Rate (Chars/Sec)
T
ypematic Rate (Chars/Sec)
TT
ypematic Rate (Chars/Sec)ypematic Rate (Chars/Sec)
TT
ypematic Rate (Chars/Sec):ypematic Rate (Chars/Sec):
T
ypematic Rate (Chars/Sec): Sets the number of times a second to repeat a
TT
ypematic Rate (Chars/Sec):ypematic Rate (Chars/Sec):
- 6 key stroke repeat a key stroke when you hold
- 8 the key down.
-10
-12
Default: 6Default: 6
Default: 6
Default: 6Default: 6
-15
-20
-24
-30
IEZ / ITZV4 Motherboard User’s Manual
3-6
Page 23
III CMOS SETUP UTILITY
""
"
""
TT
ypematic Delay (Msec)ypematic Delay (Msec)
T
ypematic Delay (Msec)
TT
ypematic Delay (Msec)ypematic Delay (Msec)
TT
ypematic Delay (Msec):ypematic Delay (Msec):
T
ypematic Delay (Msec): Select the delay time after the key is held
TT
ypematic Delay (Msec):ypematic Delay (Msec):
- 250 down held down before it begins to repeat
- 500 the key strokes.
- 750
- 1000
Default: 250Default: 250
Default: 250
Default: 250Default: 250
""
"
""
Security optionSecurity option
Security option
Security optionSecurity option
Security option:Security option:
Security option: Select whether the password is required
Security option:Security option:
- Setup every time when you enter setup. Setup -
- System The system will boot up. System - The
system will not boot and access to setup
will be denied if the correct password the
correct password is not entered at theprompt.
Default: SetupDefault: Setup
Default: Setup
Default: SetupDefault: Setup
""
"
""
OS Select for DRAM > 64MBOS Select for DRAM > 64MB
OS Select for DRAM > 64MB
OS Select for DRAM > 64MBOS Select for DRAM > 64MB
OS Select for DRAM > 64MB:OS Select for DRAM > 64MB:
OS Select for DRAM > 64MB: Select OS2 only if you are running OS/2
OS Select for DRAM > 64MB:OS Select for DRAM > 64MB:
- Non-OS/2 operating system with greater than 64MB
- OS/2 of RAM on the system.
Default: Non-OS/2Default: Non-OS/2
Default: Non-OS/2
Default: Non-OS/2Default: Non-OS/2
""
"
""
Report No FDD for WIN 95Report No FDD for WIN 95
Report No FDD for WIN 95
Report No FDD for WIN 95Report No FDD for WIN 95
Report No FDD for WIN 95:Report No FDD for WIN 95:
Report No FDD for WIN 95: Whether report no FDD for WIN 95 or not.
Report No FDD for WIN 95:Report No FDD for WIN 95:
-Yes
-No
Default: NoDefault: No
Default: No
Default: NoDefault: No
IEZ / ITZV24 Motherboard User’s Manual
3-7
Page 24
y
III CMOS SETUP UTILITY
3- 4 Advanced Chipset Features
This item allows you to configure the system based on the specific features of the chipset.
This chipset manages bus speed and access to system memory recources, and external
cache. It must be stated that these items should never need to be altered.The default settings
have been chosen because they provide you the best operating conditions for your system.
The only time you might consider making any changes if you discovered that the datas were
being lost while control your system.
CMOS Setup Utility – Copyright © 1984 – 2000 Award Software
Advanced Chi pset Feat ures
SDRAM CAS Latency Time 2
SDRAM Cycle Time Tras/Trc 6/8
SDRAM RAS-to-CAS Delay 3
SDRAM RAS Precharge Time 3
System BIOS Cacheable Disabled
Video BIOS Cacheable Disabled
Memory Hole At 15M-16M Disabled
CPU Latency Timer Disabled
Delayed Transaction Enabled
On-Chip Video Window Size 64MB
Use VGA BIOS in VBU Block Enabled
Local Memory Frequency 100 Mhz
* Onboard Display Cache Setting *
CAS# Latency 3
Paging Mode Control Open
RAS-to-CAS Override b
RAS# Timing Fast
RAS# Precharge Timing Fast
↑↓←→
Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults F7:Optimized Defaults
""
"
""
SDRAM CAS Latency TimeSDRAM CAS Latency Time
SDRAM CAS Latency Time
SDRAM CAS Latency TimeSDRAM CAS Latency Time
SDRAM CAS Latency Time:SDRAM CAS Latency Time:
SDRAM CAS Latency Time: When synchronous DRAM is installed, the
SDRAM CAS Latency Time:SDRAM CAS Latency Time:
CAS# LT
Menu Level
Item Hel p
!
- 3 number of clock cycles of CASlatency
- 2 depends on the DRAM timing
Default: 3Default: 3
Default: 3
Default: 3Default: 3
""
"
""
SDRAM Cycle TSDRAM Cycle T
SDRAM Cycle T
SDRAM Cycle TSDRAM Cycle T
SDRAM Cycle TSDRAM Cycle T
SDRAM Cycle T
SDRAM Cycle TSDRAM Cycle T
ime Time T
ime T
ime Time T
ime Time T
ime T
ime Time T
ras/Tras/T
rcrc
ras/T
rc
ras/Tras/T
rcrc
ras/Tras/T
rc:rc:
ras/T
rc: Select the number of SCLKs for an access
ras/Tras/T
rc:rc:
- 6/8
- 5/7
Default: 6/8Default: 6/8
Default: 6/8
Default: 6/8Default: 6/8
""
"
""
SDRAM RAS-to-CAS DelaySDRAM RAS-to-CAS Delay
SDRAM RAS-to-CAS Delay
SDRAM RAS-to-CAS DelaySDRAM RAS-to-CAS Delay
SDRAM RAS-to-CAS Delay:SDRAM RAS-to-CAS Delay:
SDRAM RAS-to-CAS Delay: When synchronous DRAM is installed in the
SDRAM RAS-to-CAS Delay:SDRAM RAS-to-CAS Delay:
- 3 system, this field lets you insert a timing delay
- 2 between the as CAS and RAS strobe signals,
used DRAM is written to, read from,or
refreshed.
Default: 3Default: 3
Default: 3
Default: 3Default: 3
IEZ / ITZV4 Motherboard User’s Manual
3-8
Page 25
III CMOS SETUP UTILITY
""
"
""
SDRAM RAS Precharge TimeSDRAM RAS Precharge Time
SDRAM RAS Precharge Time
SDRAM RAS Precharge TimeSDRAM RAS Precharge Time
SDRAM RAS Precharge Time:SDRAM RAS Precharge Time:
SDRAM RAS Precharge Time: If an insufficient number of cycles is alllowed
SDRAM RAS Precharge Time:SDRAM RAS Precharge Time:
- 3 for the RAS to accumulate its charge before
- 2 DRAM refresh, the refresh may be incomplete
and theDRAM may fail to retain data.
Default: 3Default: 3
Default: 3
Default: 3Default: 3
""
"
""
System BIOS CacheableSystem BIOS Cacheable
System BIOS Cacheable
System BIOS CacheableSystem BIOS Cacheable
System BIOS Cacheable:System BIOS Cacheable:
System BIOS Cacheable: Selecting Enabled allows caching of the system
System BIOS Cacheable:System BIOS Cacheable:
- Enabled BIOS ROM at F0000h-FFFFFh, resulting in better
- Disabled system performance.
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
""
"
""
Video BIOS CacheableVideo BIOS Cacheable
Video BIOS Cacheable
Video BIOS CacheableVideo BIOS Cacheable
Video BIOS Cacheable:Video BIOS Cacheable:
Video BIOS Cacheable: Select Enabled allows caching of the video
Video BIOS Cacheable:Video BIOS Cacheable:
- Enabled BIOS, resulting in better system performance.
- Disabled
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
""
"
""
Memory Hole At 15M - 16MMemory Hole At 15M - 16M
Memory Hole At 15M - 16M
Memory Hole At 15M - 16MMemory Hole At 15M - 16M
Memory Hole At 15M - 16M:Memory Hole At 15M - 16M:
Memory Hole At 15M - 16M: When this area is reserved, it cannot be
Memory Hole At 15M - 16M:Memory Hole At 15M - 16M:
- Enabled cached. The user information of peripherals
- Disabled that need to use this area of system memory
usually discusses their memory requirements.
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
""
"
""
CPU Latency TimerCPU Latency Timer
CPU Latency Timer
CPU Latency TimerCPU Latency Timer
CPU Latency TimerCPU Latency Timer
CPU Latency Timer This option allows you to Enabled/Disabled CPU
CPU Latency TimerCPU Latency Timer
- Enabled latency Timer.
- Disabled
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
""
"
""
Delayed TDelayed T
Delayed T
Delayed TDelayed T
Delayed TDelayed T
Delayed T
Delayed TDelayed T
ransactionransaction
ransaction
ransactionransaction
ransaction:ransaction:
ransaction: Select Enabled to support compliance with PCI
ransaction:ransaction:
- Enabled spec i f i c a ti o n v e r si o n 2 . 1
- Disabled
Default: EnabledDefault: Enabled
Default: Enabled
Default: EnabledDefault: Enabled
IEZ / ITZV4 Motherboard User’s Manual
3-9
Page 26
III CMOS SETUP UTILITY
""
"
""
On-chip Video Window SizeOn-chip Video Window Size
On-chip Video Window Size
On-chip Video Window SizeOn-chip Video Window Size
On-chip Video Window Size:On-chip Video Window Size:
On-chip Video Window Size: Select the on-chip video window size for VGA
On-chip Video Window Size:On-chip Video Window Size:
- Enabled drive use.
- 32MB
--
- 64MB
--
""
" Use VGA BIOS in VBU Block Let you determine whether use VGA BIOS in
""
Default: 64MBDefault: 64MB
Default: 64MB
Default: 64MBDefault: 64MB
- Enabled VBU Block or not.
- Disabled
"
Local Memory FrequencyLocal Memory Frequency
Local Memory Frequency
Local Memory FrequencyLocal Memory Frequency
Local Memory FrequencyLocal Memory Frequency
Local Memory Frequency Normally, the local memory frequency equals
Local Memory FrequencyLocal Memory Frequency
Default: EnabledDefault: Enabled
Default: Enabled
Default: EnabledDefault: Enabled
- 100MHz CPU frequency. But this item letyou choose
- 133MHz local memory frequency, which means you
can let local memory and CPU work in different
frequency.
Default: 100MHzDefault: 100MHz
Default: 100MHz
Default: 100MHzDefault: 100MHz
"
CAS # LatencyCAS # Latency
CAS # Latency
CAS # LatencyCAS # Latency
CAS # Latency:CAS # Latency:
CAS # Latency: Select the local memory clock periods.
CAS # Latency:CAS # Latency:
-3
-2
Default: 3Default: 3
Default: 3
Default: 3Default: 3
"
Paging Mode ControlPaging Mode Control
Paging Mode Control
Paging Mode ControlPaging Mode Control
Paging Mode Control:Paging Mode Control:
Paging Mode Control: Select the paging mode control.
Paging Mode Control:Paging Mode Control:
- Open
- Close
"
RAS-to-CAS OverrideRAS-to-CAS Override
RAS-to-CAS Override
RAS-to-CAS OverrideRAS-to-CAS Override
RAS-to-CAS Override:RAS-to-CAS Override:
RAS-to-CAS Override: Select the display cache clock periods control.
RAS-to-CAS Override:RAS-to-CAS Override:
Default: OpenDefault: Open
Default: Open
Default: OpenDefault: Open
- By CAS # LT
- Override
"
RAS # TimingRAS # Timing
RAS # Timing
RAS # TimingRAS # Timing
RAS # Timing:RAS # Timing:
RAS # Timing: This item controls RAS#active to Protegra, and
RAS # Timing:RAS # Timing:
Default: By CAS # LDefault: By CAS # L
Default: By CAS # L
Default: By CAS # LDefault: By CAS # L
TT
T
TT
- Fast refresh to RAS# active delay (in local memory
- Slow clocks).
Default: FastDefault: Fast
Default: Fast
Default: FastDefault: Fast
"
RAS # Precharge TimingRAS # Precharge Timing
RAS # Precharge Timing
RAS # Precharge TimingRAS # Precharge Timing
RAS # Precharge Timing:RAS # Precharge Timing:
RAS # Precharge Timing: This item controls RAS# precharge (in local
RAS # Precharge Timing:RAS # Precharge Timing:
- Fast memory clocks).
- Slow
Default: FastDefault: Fast
Default: Fast
Default: FastDefault: Fast
IEZ / ITZV4 Motherboard User’s Manual
3-10
Page 27
_____________________________
III CMOS SETUP UTILITY
3-5 Integrated Peripherals
C M O S Se tu p Utility – C o p yr ig h t © 1 9 84 – 2 0 00 A w ar d S of tw ar e
OnChip Pri mary PCI IDE
OnChip Secondary PCI IDE
ID E Primary Maste r PIO
ID E Primary Slave PIO
IDE Secondary Master PIO
IDE Secondary Slave PIO
ID E Primary Maste r UDMA
ID E Primary Slave UDMA
IDE Secondary Master UDMA
IDE Secondary Slave UD M A
USB Controller
USB Keyboard S upport
Init Display First
AC97 Audi o
AC97 Modem
ID E HDD Block Mode
KBC i nput cloc k
Power On Function
∗
KB Power ON Password
∗ Hot Key Power On
Onboard FD C Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
∗ UR2 Duplex mode
Onboard Paral le l Por t
Parall el Port Mode
∗ ECP M ode Use DMA
Game Port Addres s
Midi P ort Addres s
Midi P ort IRQ
↑↓←→
Mov e Enter: Select +/-/P U/PD: Value F 10:Sav e ESC: Exit F 1:General Help
F5:Previous Values F6:Fail-safe defaults F7:Optimized Defaults
"
On-Chip Primary / Secondary PCI IDEOn-Chip Primary / Secondary PCI IDE
On-Chip Primary / Secondary PCI IDE
On-Chip Primary / Secondary PCI IDEOn-Chip Primary / Secondary PCI IDE
On-Chip Primary / Secondary PCI IDE:On-Chip Primary / Secondary PCI IDE:
On-Chip Primary / Secondary PCI IDE:
On-Chip Primary / Secondary PCI IDE:On-Chip Primary / Secondary PCI IDE:
Integrated Peripherals
Enabl ed
Enabl ed
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Enabl ed
Dis abled
PC I Sl ot
Auto
Auto
Enabl ed
8MHz
Hot Key
Enter
Ctrl-F1
Enabl ed
3F8/IRQ4
2F8/IRQ3
Normal
Half
378/ IRQ7
SPP
3
201
330
10
Item Help
Menu Level
!
- Enabled The integrated peripheral controller contains
- Disabled an IDE interface with support for two IDE
channels. Select Enabled to activate each
channel separately.
Default: EnabledDefault: Enabled
Default: Enabled
Default: EnabledDefault: Enabled
"
IDE Primary / Secondary Master / Slave PIOIDE Primary / Secondary Master / Slave PIO
IDE Primary / Secondary Master / Slave PIO
IDE Primary / Secondary Master / Slave PIOIDE Primary / Secondary Master / Slave PIO
IDE Primary / Secondary Master / Slave PIO:IDE Primary / Secondary Master / Slave PIO:
IDE Primary / Secondary Master / Slave PIO:
IDE Primary / Secondary Master / Slave PIO:IDE Primary / Secondary Master / Slave PIO:
- Auto The four IDE PIO fields let you set a PIO mode
- Mode 0 for each of the four IDE devices that IDE
- Mode 1 interface support onboard. Mode 0 through 4
- Mode 2 provide successively increased performance.
- Mode 3 In Auto mode, the system automatically
- Mode 4 determines the best mode for each device.
Default: AutoDefault: Auto
Default: Auto
Default: AutoDefault: Auto
"
IDE Primary / Secondary Master / Slave UDMAIDE Primary / Secondary Master / Slave UDMA
IDE Primary / Secondary Master / Slave UDMA
IDE Primary / Secondary Master / Slave UDMAIDE Primary / Secondary Master / Slave UDMA
IDE Primary / Secondary Master / Slave UDMA:IDE Primary / Secondary Master / Slave UDMA:
IDE Primary / Secondary Master / Slave UDMA:
IDE Primary / Secondary Master / Slave UDMA:IDE Primary / Secondary Master / Slave UDMA:
- Auto If your hard drive and system software both
- Disabled support Ultra DMA 33, select Auto to enable
BIOS support.
DefaDefa
ult: Autoult: Auto
Defa
ult: Auto
DefaDefa
ult: Autoult: Auto
IEZ / ITZV4 Motherboard User’s Manual
3-11
Page 28
III CMOS SETUP UTILITY
! USB Controller
USB Controller:USB Controller:
USB Controller: Select Enabled if your system contains a
USB Controller:USB Controller:
- Enabled Universal Seria Bus (USB) controller and
- Disabled you have a USB peripheral.
Default: EnabledDefault: Enabled
Default: Enabled
Default: EnabledDefault: Enabled
!
USB Keyboard SupportUSB Keyboard Support
USB Keyboard Support
USB Keyboard SupportUSB Keyboard Support
USB Keyboard Support:USB Keyboard Support:
USB Keyboard Support: Select Enabled if your system contains a
USB Keyboard Support:USB Keyboard Support:
- Enabled universal Serial Bus (USB) controller and
- Disabled you have a USB keyboard.
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
!
Init Display FirstInit Display First
Init Display First
Init Display FirstInit Display First
Init Display First:Init Display First:
Init Display First: This item allows you to decide to active
Init Display First:Init Display First:
- PCI Slot whether PCI slot or on-chip VGA first.
- Onboard
Default: PCI SlotDefault: PCI Slot
Default: PCI Slot
Default: PCI SlotDefault: PCI Slot
!
AC 97 Audio / ModemAC 97 Audio / Modem
AC 97 Audio / Modem
AC 97 Audio / ModemAC 97 Audio / Modem
AC 97 Audio / Modem:AC 97 Audio / Modem:
AC 97 Audio / Modem: This item allows you to decide to enable/
AC 97 Audio / Modem:AC 97 Audio / Modem:
- Auto disable the 810 chipset family to support
- Disabled AC 97 audio / modem.
Default: AutoDefault: Auto
Default: Auto
Default: AutoDefault: Auto
!
IDE HDD Block ModeIDE HDD Block Mode
IDE HDD Block Mode
IDE HDD Block ModeIDE HDD Block Mode
IDE HDD Block Mode:IDE HDD Block Mode:
IDE HDD Block Mode: If your IDE hard drive supports block mode
IDE HDD Block Mode:IDE HDD Block Mode:
- Enabled (most new drives do), select Enabled for
- Disabled automatic detection of the optimal number of
block read / write per sector the drive can
support.
Default: EnabledDefault: Enabled
Default: Enabled
Default: EnabledDefault: Enabled
!
KBC input clockKBC input clock
KBC input clock
KBC input clockKBC input clock
KBC input clock:KBC input clock:
KBC input clock: Set the KBC input clock.
KBC input clock:KBC input clock:
- 8MHz
- 12MHz
Default: 8MHzDefault: 8MHz
Default: 8MHz
Default: 8MHzDefault: 8MHz
!
POWER ON FunctionPOWER ON Function
POWER ON Function
POWER ON FunctionPOWER ON Function
POWER ON Function:POWER ON Function:
POWER ON Function: Set the power on function mode for power on.
POWER ON Function:POWER ON Function:
- Password
- Hot KEY
- Mouse Left / Right
Default: Any KEYDefault: Any KEY
Default: Any KEY
Default: Any KEYDefault: Any KEY
- Any KEY
- Botton Only
- Keyboard 98
IEZ / ITZV4 Motherboard User’s Manual
3-12
Page 29
III CMOS SETUP UTILITY
"
KB Power ON PasswordKB Power ON Password
KB Power ON Password
KB Power ON PasswordKB Power ON Password
KB Power ON Password:KB Power ON Password:
KB Power ON Password: If Power On Function is set Password,this
KB Power ON Password:KB Power ON Password:
option let you set KB Power OnPassword.
Press <Enter> and enter your password.
"
Hot Key Power ONHot Key Power ON
Hot Key Power ON
Hot Key Power ONHot Key Power ON
Hot Key Power ON:Hot Key Power ON:
Hot Key Power ON: This option let you choose Power ON Key
Hot Key Power ON:Hot Key Power ON:
- Ctrl-F1 from <Ctrl-F1> to <Ctrl-F12>.
~ Ctrl-F12
Default: Ctrl-F1Default: Ctrl-F1
Default: Ctrl-F1
Default: Ctrl-F1Default: Ctrl-F1
"
Onboard FDC ControllerOnboard FDC Controller
Onboard FDC Controller
Onboard FDC ControllerOnboard FDC Controller
Onboard FDC Controller:Onboard FDC Controller:
Onboard FDC Controller: Select Enabled if your system has a floppy
Onboard FDC Controller:Onboard FDC Controller:
- Enabled disk controller (FDC) installed on the system
- Disabled board and you wish to use it. If you install an
add-in FDC or the system has no floppy drive,
select Disabled in this field.
Default: EnabledDefault: Enabled
Default: Enabled
Default: EnabledDefault: Enabled
"
Onboard Serial Port 1/2Onboard Serial Port 1/2
Onboard Serial Port 1/2
Onboard Serial Port 1/2Onboard Serial Port 1/2
Onboard Serial Port 1/2:Onboard Serial Port 1/2:
Onboard Serial Port 1/2: Select a logical COM port name and matching
Onboard Serial Port 1/2:Onboard Serial Port 1/2:
- Auto address for the first and second serial ports.
- Disabled Select an address and corresponding interrut
- 3F8/IRQ4 for the first and second serial ports.
- 2F8/IRQ3
- 3E8/IRQ4
- 2E8/IRQ3
Default: Por1 3F8/IRQ4Default: Por1 3F8/IRQ4
Default: Por1 3F8/IRQ4
Default: Por1 3F8/IRQ4Default: Por1 3F8/IRQ4
Port2 2F8/IRQ3Port2 2F8/IRQ3
Port2 2F8/IRQ3
Port2 2F8/IRQ3Port2 2F8/IRQ3
"
UART Mode SelectUART Mode Select
UART Mode Select
UART Mode SelectUART Mode Select
UART Mode Select:UART Mode Select:
UART Mode Select: Let you choose UART Mode.
UART Mode Select:UART Mode Select:
- Normal
- IrDA
- ASKIR
"
Onboard Parallel PortOnboard Parallel Port
Onboard Parallel Port
Onboard Parallel PortOnboard Parallel Port
Onboard Parallel Port:Onboard Parallel Port:
Onboard Parallel Port: Select a logical LPT port address and
Onboard Parallel Port:Onboard Parallel Port:
Default: NormalDefault: Normal
Default: Normal
Default: NormalDefault: Normal
- 378/IRQ7 corresponding interrupt for the physical
- 278/IRQ5 parallel port.
- 3BC/IRQ7
Default: 378/IRQ7Default: 378/IRQ7
Default: 378/IRQ7
Default: 378/IRQ7Default: 378/IRQ7
- Disabled
IEZ / ITZV4 Motherboard User’s Manual
3-13
Page 30
III CMOS SETUP UTILITY
!
Parallel Port ModeParallel Port Mode
Parallel Port Mode
Parallel Port ModeParallel Port Mode
Parallel Port Mode:Parallel Port Mode:
Parallel Port Mode: Select an operating mode for the on board
Parallel Port Mode:Parallel Port Mode:
- SPP parallel (printer) port.
- EPP
- ECP
- ECP+EPP
!
Game Port AddressGame Port Address
Game Port Address
Game Port AddressGame Port Address
Game Port Address:Game Port Address:
Game Port Address: Select an address for game port.
Game Port Address:Game Port Address:
- Disabled
- 201
- 209
! Midi Port Address
Midi Port Address: Select an address for Midi Port.
- Disabled
- 330
- 300
- 290 Default: 330
Default: SPPDefault: SPP
Default: SPP
Default: SPPDefault: SPP
Default: 201Default: 201
Default: 201
Default: 201Default: 201
!
Midi Port IRQMidi Port IRQ
Midi Port IRQ
Midi Port IRQMidi Port IRQ
Midi Port IRQ:Midi Port IRQ:
Midi Port IRQ: Select a corresponding interrupt for Midi Port.
Midi Port IRQ:Midi Port IRQ:
- 5
-10 Default: 10
IEZ / ITZV4 Motherboard User’s Manual
3-14
Page 31
___________________________
III CMOS SETUP UTILITY
3-6 Power Management Setup
The Power Management Setup allows you to configure your system effectively save
energy while operating in a manner consistent with your own style of computer use.
ACPI functio n
ACPI Suspend Type
Power Management
Video Off Method
Video Off In Suspend
Suspend Type
MODEM Use IRQ
Suspend Mode
HDD Power Down
Soft-Off b y P W R -BTTN
Power On by Ring
Resume by Alarm
∗ Date (of M onth) Alarm
∗ Time (hh:mm:ss:) Alarm
** Reload Global Timer Events **
Primar y IDE 0
Primar y IDE 1
Seconda ry IDE 0
Seconda ry IDE 1
FDD, COM, LPT Port
PCI PIR Q [A -D ]#
↑↓←→
F5 :Previo us Val ues F6 :Fail -sa fe def aults F7 :Opti mized D efault s
" ACPI Function
ACPI Function: This opotion allows you to enable/disable the Advance
− Enabled Configuration and power Interface which offers
− Disabled improved power management
CMO S Setup Utility – Copyright © 1984 – 2000 Award Softw are
Power Management Setup
Enabled
S3 ( STR)
User De fin e
DPMS
Yes
P wrOn S uspend
3
Disabled
Disabled
Instant-Off
Enabled
Disabled
0
0 0 0
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Move Enter : Sel ect +/- /PU/PD: Val ue F10:Sav e ESC: Exit F1:General Hel p
Item Help
Menu Le vel
!
" ACPI Suspend Type
ACPI Suspend Type: Select type for ACPI Suspend.
− S1 (POS)
− S3 (STR) Default: S1 (POS)
""
" Power Management
""
Power Management: This category allows you to select the type(or degree)
− User Define of power directly related to the following modes:
− Min Saving HDD Power Down; Doze Mode; Suspend Mode.
− Max Saving User Define allows you to set each mode individually.
IEZ / ITZV4 Motherboard User’s Manual
Default: Enabled
When not disabled, each of the ranges are from 1min.
to 1 hr. except for HDD Power Down which ranges
from 1 min. to 15 min. and disable.
Default: User DefineDefault: User Define
Default: User Define
Default: User DefineDefault: User Define
3-15
Page 32
III CMOS SETUP UTILITY
""
"
""
Video Off MethodVideo Off Method
Video Off Method
Video Off MethodVideo Off Method
Video Off Method:Video Off Method:
Video Off Method: Determines the manner in which the monitor is blanded
Video Off Method:Video Off Method:
- V/H SYNC+Blank System turns off vertical and horizontal synchroniza
- DPMS tion ports and writes blanks to the video buffer. Select
- Blank Screen this option if your monitor supports.System only writes
blanks to the video buffer.
Default: DPMSDefault: DPMS
Default: DPMS
Default: DPMSDefault: DPMS
""
"
""
Video Off In SuspendVideo Off In Suspend
Video Off In Suspend
Video Off In SuspendVideo Off In Suspend
Video Off In Suspend:Video Off In Suspend:
Video Off In Suspend: Setup whether video off in suspend or not.
Video Off In Suspend:Video Off In Suspend:
-Yes
-No
Default: YDefault: Y
Default: Y
Default: YDefault: Y
""
"
""
Suspend TSuspend T
Suspend T
Suspend TSuspend T
Suspend TSuspend T
Suspend T
Suspend TSuspend T
ypeype
ype
ypeype
ype:ype:
ype: This item lets you select a method of global system
ype:ype:
eses
es
eses
- Stop Grant suspend.
- PwrOn Suspend
Default: PwrOn SuspendDefault: PwrOn Suspend
Default: PwrOn Suspend
Default: PwrOn SuspendDefault: PwrOn Suspend
""
"
""
Modem Use IRQModem Use IRQ
Modem Use IRQ
Modem Use IRQModem Use IRQ
Modem Use IRQ:Modem Use IRQ:
Modem Use IRQ: Name the interrupt request (IRQ) line assigned to the
Modem Use IRQ:Modem Use IRQ:
- NA modem (if any) on your system.
- 3,4,5,7,9,10,11 Select IRQ always awakens the system.
""
"
""
Suspend ModeSuspend Mode
Suspend Mode
Suspend ModeSuspend Mode
Suspend ModeSuspend Mode
Suspend Mode After the selected period of system inactivity,
Suspend ModeSuspend Mode
- 1/2/4/8/12/20/30/40Min all devices except the CPU shut off.
- 1 Hour
- Disabled
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
""
"
""
HDD Power DownHDD Power Down
HDD Power Down
HDD Power DownHDD Power Down
HDD Power DownHDD Power Down
HDD Power Down After the selected period of drive inactivity,
HDD Power DownHDD Power Down
- 1/2/3/4/5/6/7/8/9 the hard disk drive powers down while all
/10/11/12/13/14/15 Min other devices remain active.
- Disabled
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
IEZ / ITZV4 Motherboard User’s Manual
3-16
Page 33
III CMOS SETUP UTILITY
!!
!
!!
Soft-Off by PWR-BTTNSoft-Off by PWR-BTTN
Soft-Off by PWR-BTTN
Soft-Off by PWR-BTTNSoft-Off by PWR-BTTN
Soft-Off by PWR-BTTNSoft-Off by PWR-BTTN
Soft-Off by PWR-BTTN When Enabled, turning the system off with the on/off
Soft-Off by PWR-BTTNSoft-Off by PWR-BTTN
- Instant-Off button places the system in a very low-power-usage
- Delay 4 Sec. state, with only enough circuitry receiving power to
detect power button activity or Resume by Ring
activity.
Default: Instant-OffDefault: Instant-Off
Default: Instant-Off
Default: Instant-OffDefault: Instant-Off
!!
!
!!
Power On by RingPower On by Ring
Power On by Ring
Power On by RingPower On by Ring
Power On by RingPower On by Ring
Power On by Ring Setup whether Power on by ring or not.
Power On by RingPower On by Ring
- Enabled
- Disabled
!!
!
!!
Resume by AlarmResume by Alarm
Resume by Alarm
Resume by AlarmResume by Alarm
Resume by AlarmResume by Alarm
Resume by Alarm Set whether resume by alarm or not.
Resume by AlarmResume by Alarm
Default: EnabledDefault: Enabled
Default: Enabled
Default: EnabledDefault: Enabled
- Enabled
- Disabled
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
!!
!
!!
Primary/Secondary IDE 0 / IDE 1Primary/Secondary IDE 0 / IDE 1
Primary/Secondary IDE 0 / IDE 1
Primary/Secondary IDE 0 / IDE 1Primary/Secondary IDE 0 / IDE 1
Primary/Secondary IDE 0 / IDE 1:Primary/Secondary IDE 0 / IDE 1:
Primary/Secondary IDE 0 / IDE 1:
Primary/Secondary IDE 0 / IDE 1:Primary/Secondary IDE 0 / IDE 1:
- Enabled This option allows you determine whether enable
- Disabled Primary/Secondary IDE 0/IDE 1 or not.
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
!!
!
!!
FDD,COM,LPT PortFDD,COM,LPT Port
FDD,COM,LPT Port
FDD,COM,LPT PortFDD,COM,LPT Port
FDD,COM,LPT PortFDD,COM,LPT Port
FDD,COM,LPT Port This option allows you set whether enable FDD, COM,
FDD,COM,LPT PortFDD,COM,LPT Port
- Enabled LPT Port or not.
- Disabled
!!
!
!!
PCI PIRQ[A-D]#PCI PIRQ[A-D]#
PCI PIRQ[A-D]#
PCI PIRQ[A-D]#PCI PIRQ[A-D]#
PCI PIRQ[A-D]#PCI PIRQ[A-D]#
PCI PIRQ[A-D]# This option lets you set PCI PIRQ [A-D]#.
PCI PIRQ[A-D]#PCI PIRQ[A-D]#
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
- Enabled
- Disabled
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
IEZ / ITZV4 Motherboard User’s Manual
3-17
Page 34
III CMOS SETUP UTILITY
3-73-7
3-7
3-73-7
This section describes configuring the PCI bus system. PCI- Personal Computer
PnP/PCI ConfigurationsPnP/PCI Configurations
PnP/PCI Configurations
PnP/PCI ConfigurationsPnP/PCI Configurations
I I
Interconnect,
I I
is a system which allows I/O devices to operate at speeds nearing the speed of CPU itself
using when communicates with its own special components.This section covers some very
technical items and it is strongly recommended that only experienced users should make any
changes to the default settings.
CMOS Setup Utili ty - Copyright © 1984-2000 Award Software
PNP OS Installed No
Reset Co nfiguration Data Disabled
Res ources Contro lled By Auto(ESCD)
* IRQ Resources
* DMA Resources
* Memory Resources
PCI/V GA Pa lette Snoop Disabled
"#$ %
: Move Enter:Select +/-/PU/ PD:Value F10:Save ESC:Exit F1: General Help
F5:Previ ous Values F6: Fail-Saf e Defaul ts F7:Optimized D efaults
PnP/PCI Configurations
Press Enter
Menu Level
Item Help
!
&&
&
&&
Reset Configuration DataReset Configuration Data
Reset Configuration Data
Reset Configuration DataReset Configuration Data
Reset Configuration DataReset Configuration Data
Reset Configuration Data Normally , you leave this field Disabled. Select Enabled
Reset Configuration DataReset Configuration Data
- Enabled to reset Extended System Configuration Data (ESCD)
- Disabled when you exit Setup if you have installed a new add-on
and the system reconfiguration has caused such a
serious conflict that the operating system cannot boot.
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
&&
&
&&
Resources controlled ByResources controlled By
Resources controlled By
Resources controlled ByResources controlled By
Resources controlled ByResources controlled By
Resources controlled By The Plug and Play AwardBIOS can automatically
Resources controlled ByResources controlled By
- Auto(ESCD) configure all the boot and Plug and Play compatible
- Manual devices. If you select Auto, all the interrupt request
(IRQ) and DMA assignment fields disappear, as the
BIOS automatically assigns them.
Default: Auto(ESCD)Default: Auto(ESCD)
Default: Auto(ESCD)
Default: Auto(ESCD)Default: Auto(ESCD)
&&
&
&&
PCI/VGA Palette SnoopPCI/VGA Palette Snoop
PCI/VGA Palette Snoop
PCI/VGA Palette SnoopPCI/VGA Palette Snoop
PCI/VGA Palette SnoopPCI/VGA Palette Snoop
PCI/VGA Palette Snoop Leave this field at Disabled.
PCI/VGA Palette SnoopPCI/VGA Palette Snoop
--
- Enabled
--
--
- Disabled
--
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
IEZ / ITZV4 Motherboard User’s Manual
3-18
Page 35
III CMOS SETUP UTILITY
3-83-8
3-8
3-83-8
3-93-9
3-9
3-93-9
PC Health StatusPC Health Status
PC Health Status
PC Health StatusPC Health Status
This option show you some statistics including current system temp, current CPU1
temp, current CPUFAN1, FAN2 speed etc. which indicate your PC health status.
CMOS Setup Utility - Copyright © 1984-2000 Award Software
Voltage 0 1.45v
Voltage 1 0.97v
Voltage 2 2.76v
Voltage 3 6.85v
Voltage 4 11.26
Voltage 5 (-) 16.96v
Voltage 6 (-) 8.77v
Voltage 7 8.00v
Voltage Battery 3.45v
Temperature 1 28c
Temperature 2 54c
Fan 1 speed ORPM
Fan 2 speed ORPM
"#$%
: Move Enter:Selec t +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimiz ed Defaults
Frequency/VFrequency/V
Frequency/V
Frequency/VFrequency/V
oltage Controloltage Control
oltage Control
oltage Controloltage Control
CMOS Setup Utilit y - Copyright © 1984-2000Award Software
PC Health Status
Frequency / Voltage Control
Menu Level
Item Help
!
Auto Detect DIMM/PCI Clk Enabled Item Help
Spread Spectrum Disabled
Hos t CPU/DIMM/PCI Clock Defau lt
CPU Clock Ratio X 3
"#$%
: Move Enter:Select +/-/PU/PD:Value F10: Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Saf e Defaults F7:Optimized Defaults
&&
&
&&
Auto Detect DIMM/PCI ClkAuto Detect DIMM/PCI Clk
Auto Detect DIMM/PCI Clk
Auto Detect DIMM/PCI ClkAuto Detect DIMM/PCI Clk
Auto Detect DIMM/PCI Clk:Auto Detect DIMM/PCI Clk:
Auto Detect DIMM/PCI Clk: To reduce the occurrence of electromagnetic
Auto Detect DIMM/PCI Clk:Auto Detect DIMM/PCI Clk:
Menu Level
!
- Enabled interference (EMI), the BIOS detects the
- Disabled presence or absence of components in DIMM
and PCI slots and turns off system clock
generator pulses to empty slots.
Default: EnabledDefault: Enabled
Default: Enabled
Default: EnabledDefault: Enabled
IEZ / ITZV4 Motherboard User’s Manual
3-19
Page 36
III CMOS SETUP UTILITY
&&
&
&&
Spread SpectrumSpread Spectrum
Spread Spectrum
Spread SpectrumSpread Spectrum
Spread Spectrum:Spread Spectrum:
Spread Spectrum: When the system clock generator pulses, the
Spread Spectrum:Spread Spectrum:
- Enabled extreme values of the pulse generate excess
- Disabled EMI. Enabling pulse spectrum spread modula
tion changes the extreme values from spikes
to flat curves, thus reducing EMI. This benefit
may in some cases be outweighed by
problems with timing-critical devices, such as
a clock-sensitive SCSI device.
Default: DisabledDefault: Disabled
Default: Disabled
Default: DisabledDefault: Disabled
&&
&
&&
Host CPU/DIMM/PCI ClockHost CPU/DIMM/PCI Clock
Host CPU/DIMM/PCI Clock
Host CPU/DIMM/PCI ClockHost CPU/DIMM/PCI Clock
Host CPU/DIMM/PCI Clock:Host CPU/DIMM/PCI Clock:
Host CPU/DIMM/PCI Clock: Setup Host CPU/DIMM/PCI Clock
Host CPU/DIMM/PCI Clock:Host CPU/DIMM/PCI Clock:
- Default
- 66/100/33MHz
- 68/102/34MHz
- 75/112/37MHz
Default: DefaultDefault: Default
Default: Default
Default: DefaultDefault: Default
&&
&
&&
CPU Clock RatioCPU Clock Ratio
CPU Clock Ratio
CPU Clock RatioCPU Clock Ratio
CPU Clock RatioCPU Clock Ratio
CPU Clock Ratio Setup CPU Clock Ratio,you can choose from
CPU Clock RatioCPU Clock Ratio
- x3 x3/x3.5/x4/x4.5/x5/x5.5/x6/x6.5/x7/x7.5/x8.
- x3.5
-x4
Default: x3Default: x3
Default: x3
Default: x3Default: x3
- x4.5
-x5
- x5.5
-x6
- x6.5
-x7
- x7.5
-x8
IEZ / ITZV4 Motherboard User’s Manual
3-20
Page 37
III CMOS SETUP UTILITY
3-103-10
3-10
3-103-10
Load Fail-Safe DefaultsLoad Fail-Safe Defaults
Load Fail-Safe Defaults
Load Fail-Safe DefaultsLoad Fail-Safe Defaults
This option allows you load Fail-Safe Defaults settings. To load setup default, press <Y> key
to confirm the operation when you see the below display.
C M O S Setu p Utilit y - C op y ri g ht © 1984 -1999 A w ard Software
!
S tand ard CMO S Features
!
A dvanced BIO S F eatures Load F ail - Safe D efaults
!
A dvanced C hipset Features Load O ptim ized Defaults
!
Integrated Per ipherals S et Sup ervisor P assw ord
!
P ower Managem en t Set User Passwo rd
!
PnP/PCI Configura tion Save & Exit Setup
!
P C H e alth S tatus Exit Without Saving
ESC: Quit
F 1 0 : Sa v e & Exit S e t u p
3-13-1
11
3-1
3-13-1
Load Optimized DefaultsLoad Optimized Defaults
1
Load Optimized Defaults
11
Load Optimized DefaultsLoad Optimized Defaults
Lo a d F ail - Sa fe D efa u lts (Y /N )? N
Lo a d F a il - S afe D e fa u lts
!
Freque ncy/voltage con trol
: S elect Item
This option allows you load Optimized Defaults settings to optimize your system. To load
optimized default, press <Y> key to confirm the operation when you see the below display.
CMOS Setup Utility - Copyright © 1984-1999 Award Software
!
St an da r d CMO S Featur es
!
Advanced BI OS Features Load Fail - Safe Defaults
!
Advanced Chipset Features
!
Integrated Peripherals Set Su pervisor Password
!
Power Management S et User Password
!
PnP/PCI Configuration Save & Exit Setup
!
PC Health Status Exit Without Saving
ESC: Quit
F1 0 : Save & Exit Setup
Load Optimized Defaults (Y/N)?
Load Optimized Defaults
!
Fr equency/voltage control
Load Optimized Defaults
: Select Item
IEZ / ITZV4 Motherboard User’s Manual
3-21
Page 38
III CMOS SETUP UTILITY
3-123-12
3-12
3-123-12
Password prevents unauthorized use of your computer. If you set a password, the system
prompts for the correct password before boot or access to setup. The main difference
between Supervisor Password and User Password is the privilege. Because Supervisor
Password allows you to modify all CMOS setup but User password only some of them.
Their steps all as follows:
1. Highlight the item Set Supervisor Password / Set User Password on the main menu
2. The password dialog box will appear.
3. If you are installing a new password, carefully type in the password. Press ENTER
4. The system will ask you to confirm the new password by asking you to type it in a
5. If you typed the password correctly, the password will be installed.
[NOTE][NOTE]
[NOTE]
[NOTE][NOTE]
if you forget your password, or you want to cancel your password, you can do theif you forget your password, or you want to cancel your password, you can do the
if you forget your password, or you want to cancel your password, you can do the
if you forget your password, or you want to cancel your password, you can do theif you forget your password, or you want to cancel your password, you can do the
steps as the following:steps as the following:
steps as the following:
steps as the following:steps as the following:
Set Supervisor/User PasswordSet Supervisor/User Password
Set Supervisor/User Password
Set Supervisor/User PasswordSet Supervisor/User Password
and press ENTER.
after you have typed in the password. If you are deleting a password that is already
installed just press ENTER when the password dialog box appears.
second time. Carefully type the password again and press ENTER, or just press
ENTER if you are deleting a password that is already installed.
(1)(1)
(1)
(1)(1)
(2)(2)
(2)
(2)(2)
3-133-13
3-13
3-133-13
Highlight this item and press ENTER to save the changes that you have made in the setup utility
and exit the setup program. When the Save and Exit dialog box appears, press <Y> to save
and exit, or press <N> to return to the setup main menu.
3-143-14
3-14
3-143-14
Use this option to exit setup utility without saving the CMOS value changes.
Save & Exit SetupSave & Exit Setup
Save & Exit Setup
Save & Exit SetupSave & Exit Setup
Exit Without SavingExit Without Saving
Exit Without Saving
Exit Without SavingExit Without Saving
Password forgotten:Password forgotten:
Password forgotten:
Password forgotten:Password forgotten:
i. Turn off the system.
ii. Short JP1 at Pin 2-3 for a few seconds to clear CMOS.
iii. Set the JP1 back to Pin 1-2.
iv. Power on the system.
Clear Password:Clear Password:
Clear Password:
Clear Password:Clear Password:
Clear your password by key in the password you installed
before, then goto password setting to press ENTER twice.
IEZ / ITZV4 Motherboard User’s Manual
3-22
Page 39
IV SOFTWAR UTILITY
SECTION 4
SOFTW ARE UTILITY
The support software for this motherboard is supplied in a CD. All the support programs are
stored in separate folders, so you can find the program you need easily enough. We recomend
you to choose the program which you need most, it will assist your computer system to high
performance. The support software contains the following programs:
' Intel VGA Driver Program
' Intel chipset Driver Program
' Audio Codec Driver Program
4-14-1
4-1
4-14-1
4-24-2
4-2
4-24-2
4-34-3
4-3
4-34-3
Intel VGA Driver ProgramIntel VGA Driver Program
Intel VGA Driver Program
Intel VGA Driver ProgramIntel VGA Driver Program
♦♦
♦
♦♦
Intel chipset Driver ProgramIntel chipset Driver Program
Intel chipset Driver Program
Intel chipset Driver ProgramIntel chipset Driver Program
♦♦
♦ Driver files location:
♦♦
♦ ♦
♦ Driver files location:
♦ ♦
Driver files location: Driver files location:
Driver files location:
Driver files location: Driver files location:
Intel VGA Driver Program: \Video\810VGA
Intel chipset Driver Program: \Ide\810\intelinf
Please run “SETUP.EXE” file in the directory “intelinf”,
then run “SETUP.EXE” file in the directory “infinst”.
Audio Codec Driver ProgramAudio Codec Driver Program
Audio Codec Driver Program
Audio Codec Driver ProgramAudio Codec Driver Program
Audio Codec Driver Program:\Audio\810 Audio
\Ide\810\infinst
IEZ / ITZV4 Motherboard User’s Manual
4-1
Loading...