Eufy Motion Sensor User Manual

User Manual

Motion Sensor

Anker Innovations Limited. All rights reserved.
are trademarks of Anker Innovations Limited, registered in the United States and
other countries. All other trademarks are the property of their respective owners.

Model: T8910
51005002023 V01

eufy Security and eufy Security Logo

TABLE OF

CONTENTS

What’s Included

Product Overview

Mounting the Motion Sensor

02 10

03 11

05 14

Specications

Notice

Customer Service

English

01

WHAT’S INCLUDED

PRODUCT OVERVIEW

For Motion Sensor Installation

Motion Sensor T8910

Welcome Card

Mount

Mounting Screws

CR123A Battery

User Manual

3M Adhesive Strip

Battery Compartment

LED Indicator

Motion Sensor

SYNC Button

Installing Batteries

Remove the battery compartment lid on the Motion Sensor and insert the provided
CR123A battery.

English English

02

03

Adding Motion Sensor to Your System

Make sure you've completed the setup of your eufy Security HomeBase.

Note:

Follow the onscreen instructions on the Eufy Security app to add your motion sensor.

1.

Choose

Add Device

, then select

Motion Sensor

to add it to your system.

3.

The LED indicator turns solid blue to indicate the pairing is successful.

LED Status Description

Blinking blue continuously Waiting to connect

Solid blue for 5s Paired successfully

Off Failed to connect to the HomeBase

The LED indicator, device name and timer can be customized on the eufy

Note:

Security app.

MOUNTING THE MOTION
SENSOR

Find a Location for Mounting

The motion sensor can be installed on a wall. To get optimal detection coverage,

2.

Press and hold the SYNC button for 2 seconds until the LED indicator blinks
blue. The Motion Sensor is waiting to pair.

English English

04

consider the following factors before mounting the motion sensor:

• Determine the area of detection and ensure there is an unobstructed eld of
view

• Determine the height and tilt angle

• Avoid direct sources of heat or sunshine, curtains, plants, or pets.

Ideally, the motion sensor should be installed on a wall facing the door through which
people are likely to enter. We recommend placing the motion sensor close to a
corner to get the optimal detection coverage.

05

You can also install the motion sensor in your garage, dining room, or basement.

2-2.5 m

2-2.5 m

Height and Tilt Angle

The motion sensor should be mounted 2m / 6
with a tilt angle of preferably 20º downwards. If you have a large pet weighing more
than 50 lb, change to a 10º downwards tilt.

With Pets

10°

₇

ft to 2.5m / 8⅕ ft above the oor

/

⁴

No Pets

20°

To better detect the area where people may break in, rotate the motion sensor
horizontally up to 30º.

Sensitivity

The sensitivity can be adjusted based on the room size. The default setting is medium
sensitivity.

English English

06

07

Mount the Motion Sensor

1.

There are two methods of mounting the motion sensor at the selected location:

• Use the 3M adhesive strip:

Snap the adjustable wall mount onto the motion sensor base.

①

Stick the adhesive strip on the back of the sensor, remove the lm, and stick

②

the motion sensor on the wall.

Rotate the motion sensor to adjust the detection coverage.

③

Drill holes at each marking. No need to drill a pilot hole in the wooden walls.

②

Insert anchors into the holes, and fix the mount onto the wall with the

③

1 2

• Use the provided screws:

Place the mount against the wall and use a pencil to mark the desired

①

location for mounting.

English English

08

provided screws. No anchors are needed on wooden walls.

Clip the motion sensor back onto the mount.

④

Rotate the motion sensor to adjust the detection coverage.

⑤

09

Use the Motion Sensor

After the motion sensor is installed, the alarm will be triggered once movement is
detected within the motion sensor’s coverage area.

When the motion sensor is working, its LED indicator shows as below:

LED Status Description

Blinking blue Movement detected while the HomeBase is connected

Blinking red Movement detected while the HomeBase is not connected

When the motion sensor is in the test mode, the LED indicator shows as below:

LED Status Description

Solid red Enter the test mode successfully

Blinking red for 1 second

Off Failed to enter the test mode

Movement detected when the motion sensor is in the test
mode

Replace the Battery

When the motion sensor’s battery is low, the LED indicator shows as below. ou
should replace the battery to keep the motion sensor working.

LED Status Description

Blinking blue Movement detected while the HomeBase is connected

Blinking red Movement detected while the HomeBase is not connected

SPECIFICATIONS

Battery: 1× CR123A battery

Operating Temperature: -10ºC - 40ºC /14°F - 104°F

Storage Temperature: -20ºC - 60ºC /-4°F - 140°F

English English

10

11

NOTICE

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

Changes or modications not expressly approved by the party responsible

Warning:

for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class

Note:

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the
separation between the equipment and receiver. (3) Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected. (4) Consult
the dealer or an experienced radio/ TV technician for help.

FCC Radio Frequency Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The device

can be used in xed / mobile exposure condition. The min separation distance is 20cm.

Shielded cables

Notice:

All connections to other computing devices must be made using shielded cables to
maintain compliance with FCC regulations.

The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: [phone]

This product complies with the radio interference requirements of the European

Community.

English English

12

Declaration of Conformity

Hereby, Anker Innovations Limited declares that this device is in compliance with
the essential requirements and other relevant provisions of Directive 2014/53/EU.
For the declaration of conformity, visit www.eufylife.com.

Do not use the Device in the environment at too high or too low temperature, never
expose the Device under strong sunshine or too wet environment.
The suitable temperature for the product and accessories is -10°C-40°C.

RF exposure information: The Maximum Permissible Exposure (MPE) level has been
calculated based on a distance of d=20 cm between the device and the human body.
To maintain compliance with RF exposure requirement, use product that maintain a
20cm distance between the device and the human body.

CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
SUB-1G Frequency range: 866~866.8MHz (for EU) ; 920~920.8MHz (for US)
Max Output Power: 6.496dBm (ERIP)

This product is designed and manufactured with high quality materials and

components, which can be recycled and reused.

This symbol means the product must not be discarded as household waste,

and should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health
and the environment. For more information on disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you bought this product.

IC Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions:

(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause

undesired operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:

(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si

13

le brouillage est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

IC RF Statement

When using the product, maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.

Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de

vous conformer aux exigences en matière d'exposition RF.

FCC ID: 2AOKB-T8910 IC: 23451-T8910

Anker Innovations Limited

Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

CUSTOMER SERVICE

Warranty

12-month limited warranty

[phone] Mon-Fri 9AM-5PM (PT)

[phone] Mon-Fri 6AM-11AM (GMT)

[phone] Mon-Fri 6:00-11:00

Customer Support: [e-mail]

English English

14

15