Eufy Eufycam 2K Indoor Pan & Tilt User manual

Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are

trademarks of Anker Innovations Limited, registered in the United States and other

countries. All other trademarks are the property of their respective owners.

51005002218 V01

QUICK
START GUIDE

eufy Indoor Cam 2K Pan & Tilt

Table of Contents

What’s Included 01

Product Overview 02

Setting up the System 03

Mounting the Indoor Cam 05

Powering on the Indoor Cam 10

Notice 11

Customer Service 16

WHAT’S INCLUDED

PRODUCT OVERVIEW

eufy Indoor Cam 2K Pan & Tilt × 1
Model: T8410
Mounting Plate × 1
USB Cable × 1
USB Adapter × 1
Mounting Screw Pack × 1
User Manual × 1

English

eufy Indoor Cam 2K Pan & Tilt

1

2

3

5

6

1

Lens
Microphone

2

SD card slot

3

Status LED

4

4

7

Speaker

5

6

Power input

7

SYNC button

English

0201

SETTING UP THE SYSTEM

1. Download the eufy Security app from the App Store
(iOS devices) or Google Play (Android devices).

2. Sign up a eufy Security account. Go to the app
homepage. Tap
Pan 2K to your system.

3. Follow the on-screen instructions to complete the
setup.

English

Add Device

, and add the IndoorCam

LED Status

LED Status Description

Breathing blue Ready for setup
Solid blue Powered on and working properly
Blinking red Disconnected from the internet

Blinking red once Motion or sound detected

Solid red

Solid bluish violet System is initializing
Flashing blue and red

alternately

Working properly with someone
viewing the live stream or
recording event

Firmware upgrade in progress

English

0403

MOUNTING THE INDOOR CAM

Select a Location for Mounting

The camera can be placed on a table, shelf, or can be mounted
on a wall or ceiling. Select a location and height where you can
get the desired view, and can reach a power outlet easily.

• Disconnect the Indoor Cam from the power
outlet before mounting.

• Keep the eufy Indoor Cam at least 0.7 ft / 20 cm
away from walls or anything that may obstruct the

view. Do this to avoid infrared reection which

can have a negative impact on the night vision
performance.

English

> 20CM

> 20CM

English

0605

Mount the Indoor Camera

To mount the eufy Indoor Cam on the ceiling, follow the steps
below:

1. Place the positioning
card against the
ceiling and then
mark the points at
which drilling will be
required.

2. Drill holes with a
5/16” (8 mm) drill
bit.

English

Ceiling

Ceiling

3. Align the holes on the mounting plate with those in the
ceiling. Insert the anchors into the holes; anchors are
necessary for walls that are made out of hard materials such
as concrete, brick, or stucco. Fix the screws with a Phillips­head screwdriver to fasten the mounting plate to the ceiling.

Ceiling

4. Align the grooves with the mounting plate and rotate the eufy
Indoor Cam clockwise until it clicks into place.

Ceiling

English

0807

To mount the eufy Indoor Cam on a wall, we recommend using
the mounting bracket (not provided) as the illustration below.

English

POWERING ON THE INDOOR CAM

Connect the eufy Indoor Cam to a power outlet using the
provided USB cable and USB adapter. After being powered on,
the eufy Indoor Cam will be connected to the system. When it
is successfully connected, the status LED will turn solid blue.

Rotate the eufy Indoor Cam to adjust the view and check it
using the live stream which you can access in the eufy Security
app. You are now all set to use your eufy Indoor Cam.

Tip:

For troubleshooting, check Help on the eufy Security app. Refer
to the app page for LED indicator status.

English

1009

NOTICE

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.

Warning:

Changes or modications not expressly approved by the

party responsible for compliance could void the user's authority
to operate the equipment.

Note:

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more
of the following measures: (1) Reorient or relocate the receiving

English

antenna. (2) Increase the separation between the equipment and
receiver. (3) Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. (4) Consult
the dealer or an experienced radio/ TV technician for help.

FCC Radio Frequency Exposure Statement

The device has been evaluated to meet general RF exposure

requirements. The device can be used in xed/mobile exposure

condition. The min separation distance is 20cm.
Notice: Shielded cables
All connections to other computing devices must be made using

shielded cables to maintain compliance with FCC regulations.
The following importer is the responsible party
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone:[phone]

This product complies with the radio interference

requirements of the European Community.

Declaration of Conformity

Hereby, Anker Innovations Limited declares that this device is in
compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU.For the declaration of
conformity, visit the Web site:https://www.eufylife.com/.

1211

English

This product can be used across EU member states.
Due to the used enclosure material, the product shall only be

connected to a USB Interface of version 2.0 or higher.
The adapter shall be installed near the equipment and shall be

easily accessible.
Do not use the Device in the environment at too high or too low

temperature, never expose the Device under strong sunshine or
too wet environment.

The suitable temperature for T8410 and accessories is 0°C-40°C.
When charging, please place the device in an environment that has

a normal room temperature and good ventilation.
It is recommended to charge the device in an environment with a

temperature that ranges from 5°C~25°C
Please ensure to use only the charger offered by the manufacturer.

Using unauthorized charger may cause danger and violate the
authorization of the device and the guarantee article.

This charger is for indoor use only.
The charger type is TEKA012-0502000EU , output voltage/current

is 5Vdc/2A. The plug considered as disconnect device of adapter.
RF exposure information: The Maximum Permissible Exposure

(MPE) level has been calculated based on a distance of d=20 cm
between the device and the human body. To maintain compliance
with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.

English

CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS

Wi-Fi Operating Frequency Range:2412~2472MHz ; Wi-Fi Max
Output Power:14.46dBm(ERIP)

Bluetooth Operating Frequency Range:2402~2480MHz; Bluetooth
Max Output Power:0.64dBm(EIRP)

The following importer is the responsible party (contact for EU
matters only)

Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road, Tyseley,

Birmingham, B11 2AA, United Kingdom

This product is designed and manufactured with high

quality materials and components, which can be recycled
and reused.

This symbol means the product must not be discarded

as household waste, and should be delivered to an
appropriate collection facility for recycling. Proper
disposal and recycling helps protect natural resources,
human health and the environment. For more information
on disposal and recycling of this product, contact your
local municipality, disposal service, or the shop where you
bought this product.

English

1413

IC Statement

This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.

IC RF Statement:

When using the product, maintain a distance of 20cm from the
body to ensure compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20

cm du corps an de vous conformer aux exigences en matière

d'exposition RF.

English

CUSTOMER SERVICE

• Warranty

12-month Limited Warranty

• Call Us

United States [phone] Mon-Fri 9AM-5PM (PT)
United Kingdom [phone] Mon-Fri 6AM-11AM
(GMT)
Germany [phone] Mon-Fri 6:00-11:00

• Email Us

Customer Support: [e-mail]

Anker Innovations Limited
Room 1318-19,Hollywood Plaza,610 Nathan

Road,Mongkok,Kowloon,Hong Kong

English

1615

Inhaltsverzeichnis

IM LIEFERUMFANG

Im Lieferumfang 18

Produktübersicht 19

Einrichten des Systems 20

Montage der Indoor Cam 22

Einschalten der Indoor Cam 27

Kundendienst 29

1 eufy Indoor Cam 2K Pan & Tilt
Modell：T8410
1 Montageplatte
1 USB-Ladekabel
1 USB-Netzteil
1 Paket Befestigungsschrauben
1 Benutzerhandbuch

Deutsch 18

PRODUKTÜBERSICHT

EINRICHTEN DES SYSTEMS

eufy Indoor Cam 2K Pan & Tilt

1

2

3

4

5

6

7

1. Laden Sie die eufy Security-App aus dem App Store
(iOS-Geräte) oder bei Google Play (Android) herunter.

2. Richten Sie ein eufy Security-Konto ein. Navigieren
Sie zur Startseite der App.Tippen Sie auf "Gerät
hinzufügen", und fügen Sie die IndoorCam Pan 2K zu

1

Objektiv
Mikrofon

2

SD-Kartensteckplatz

3

Status-LED

4

19 Deutsch Deutsch 20

Lautsprecher

5

6

Stromeingang

7

SYNC-Taste

Ihrem System hinzu.

3. Befolgen Sie die Bildschirmanweisungen, um die
Einrichtung abzuschließen.

LED-Status

LED-Status Beschreibung

Blau an-/abschwellend Bereit zur Einrichtung
Leuchtet blau Eingeschaltet und in Funktion
Blinkt rot Vom Internet getrennt

Blinkt einmal rot Bewegung oder Geräusch erkannt

Leuchtet rot

Leuchtet blau-violett System wird initialisiert
Blinkt abwechselnd blau

und rot

21 Deutsch Deutsch 22

In Funktion, Live-Stream oder die
Aufzeichnung eines Ereignisses wird
betrachtet

Firmware-Aktualisierung wird
durchgeführt

MONTAGE DER INDOOR CAM

Auswählen des Montageorts

Die Kamera kann auf einem Tisch oder in einem Regal aufgestellt
oder an der Wand oder Decke montiert werden. Wählen Sie einen
Standort nahe an einer Steckdose und eine Höhe aus, von wo aus
Sie die gewünschte Ansicht erhalten.

Montage der Indoor Cam

• Trennen Sie die Indoor Cam vor der Montage von
der Steckdose.

• Halten Sie die eufy Indoor Cam mindestens 20 cm
von Wänden oder allen anderen Objekten entfernt,
die die Sicht behindern könnten. Dies ist erforderlich,

um Infrarot-Reexionen zu vermeiden, die sich

negativ auf die Nachtsichtleistung auswirken können.

> 20CM

> 20CM

23 Deutsch Deutsch 24

Um die eufy Indoor Cam an der Decke zu montieren, führen Sie
die folgenden Schritte aus:

1. Halten Sie die
Montageschablone
gegen die Decke und
markieren Sie dann
die Punkte, an denen
gebohrt werden
muss.

2. Bohren Sie die
Löcher mit einem
8-mm-Bohrer.

Ceiling

Ceiling