FilmScan35 Professional
-Patent pending-
User Manual
Version 1.01
April 2010
Index
I. Unpack FilmScan35 Professional Scanner.............................2
II. Install film into the film holder.............................................3
III. Quick Start..........................................................................7
IV. Operation Guide................................................................12
V. Specification......................................................................37
-1-
I. Unpack FilmScan35 Professional
FilmScan35 Professional Negative/Slide Film Holder User Manual
USB power core USB/Video cable Roll Film Holder Clean brush
Note
We strongly suggest using a clean, dry, non-alcohol
cotton swab to clean the glass surface periodically
to produce a clear image during operation.
Clean dust from FilmScanner back light, to use the
clean brush to wipe the dust.
Dust or dirt from the negative, slide films and
cover trays may affect the scanned image quality,
please make sure the materials are cleaned before
inserting into the scanner.
Please find recommend, processional purger from photo store to clean the dust on
films if any to avoid damaging the only one copy of old films.
-2-
II. Install film into the film holder
●
Install the Slide into holder
1. Open the slide holder as illustrated
2. Put slide into positive slide slot 3. Close the film holder
●
Install the Negative Film into holder
1. Open the film holder as illustrated
-3-
2. Install film into negative film slot 3. Close the film holder
●
Install the Roll Film into holder:
1. Take out the roll film holder from package
2. Insert roll film into film slot 3. Pull out the roll film in another side
-4-
Note
Figure 1
Figure 2
To avoid mirror image, follow the serial numbers (from left to right) on top of film
when install negative film into holder
If the image is upside down [see fig.2], the image can be corrected by Flip function in
hard key of device before capture, or enter playback edit menu after capture [see
fig.3 and fig.4].
-5-
<Up> then <Down>
button to perform
Flip
Flip
●
Press hard key on top of device in live view
Figure 3
●
Playback mode menu
Figure 4
-6-
III. Quick Start
Right/+ button
Film Slot
OK button
SD card Slot
Left/- button
Power button
USB port
TV out jack
Power status LED
-7-
1. Put Film onto the film cartridge
2. Insert the film cartridge into FilmScan35 Professional
-8-
3. Connect USB cable to FilmScan35 Professional
4. Turn on Device by power button
-9-
5. Press OK button to capture the image
6. Follow the menu on display for scanning
-10-
7. After finished the capture, take out the SD card which stored capture
images
8. Or read picture from PC by MSDC mode
-11-
IV. Operation Guide
Capture
Playback
Film Type
USB mode
Setting
Capture
Home: Main menu
●
●
●
●
●
Capture: capture mode (default)
Playback: playback mode
Film Type: define the film type which loaded in cartridge
USB mode: MSDC (Mass Storage Device Class) mode
Setting: TV out and format option
1. Capture
After welcome page, above menu will remains for 5 sec. User can press up/down button
for desired menu. Or system will auto enter Capture mode if there is no action during this
5 second period.
-12-
1.1 Capture: <Up>/<Down> (Hard Key)
<Up> Right/Up
<Down>
Left/Down
<Up>
<Down>
<OK> Go Next
button
●
●
Press <Down> button to enter Brightness/Color adjustment (see Chapter 1.3)
Press <Up> button to enter Mirror/Flip adjustment (see Chapter 1.2)
-13-
1.2 Capture: <Up>/<Down> - Mirror/Flip (Hard Key)
<Up> Right/Up
<Down>
Left/Down
<Up>
<Down>
<OK> Go Back
to 1.1Capture
button
●
Press <Up> button to change image left to right
●
Press <Down> button to upside down image
-14-
1.3 Capture: <Up>/<Down> - Brightness/Color (Hard Key)
<Up> Right/Up
<Down>
Left/Down
<Up>
<Down>
<OK> Go Back
to 1.1Capture
button
●
●
Press <Up> button to enter Brightness adjustment (See Chapter 1.4)
Press <Down> button to enter Color adjustment (See Chapter 1.5)
-15-
1.4 Capture: <Up>/<Down> - Brightness (Hard Key)
<Up> Right/Up
<Down>
Left/Down
<Up>
<Down>
<OK> Go Back
to 1.1Capture
button
●
●
Press <Up> button to increase Brightness with ranges of -3 to 3
Press <Down> button to decrease Brightness with ranges of -3 to 3
-16-
1.5 Capture: <Up>/<Down> - Color Red (Hard Key)
<Up> Right/Up
<Down>
Left/Down
<Up>
<Down>
<OK> Go Next
to Color Green
button
●
●
Press <Up> button to increase red color with ranges of -3 to 3
Press <Down> button to decrease red color with ranges of -3 to 3
-17-
1.6 Capture: <Up>/<Down> - Color Green (Hard Key)
<Up> Right/Up
<Down>
<Up>
<Down>
<OK> Go Next
to Color Blue
button
●
●
Press <Up> button to increase green color with ranges of -3 to 3
Press <Down> button to decrease green color with ranges of -3 to 3
-18-
1.7 Capture: <Up>/<Down> - Color Blue (Hard Key)
<Up> Right/Up
<Down>
Left/Down
<Up>
<Down>
<OK> Go Back
to 1.1Capture
button
●
●
Press <Up> button to increase blue color with ranges of -3 to 3
Press <Down> button to decrease blue color with ranges of -3 to 3
-19-
1.8 Capture mode
Live view indicator
(flashing at 0.5sec rate)
Save
Rotate +90
Cancel
Rotate -90
Home
Selected image
Once enter capture mode, there will be a red indicator on left top corner to indicate it is
in live view mode. When the film cartridge is inserted into the scanner slot, the image
always shows the positive image according to previous defined Film Type (after power on.
the Film Type is default to negative film). Reconfirm the film position through the display
before press OK button.
1.9 Capture: Edit Menu
●
●
●
(this is for adjusting the user who took the portrait picture)
●
●
Save: save captured image
Rotate +90: continue rotate +90 degrees
Rotate -90: continue rotate -90 degrees
Cancel: cancel any editing with this image
Home: Back to main menu
-20-
1.10 Live View -> Capture/Edit Menu
Save
Live View Capture/Edit Menu
OK
OK
Once press OK button in live view, the edit menu will be appeared. When user press OK
button again, the current image will be saved into SD card. The display will return to live
view again.
1.11 Capture: Save
Once user press OK button on top of FilmScan35-II-2.4-TV out, preview (live view) image
will be selected and shown on the TFT which will take between 3-4 second with 4 icons
shown on the left side of the screen. Save icon will be highlighted for user to confirm the
saving by OK button. After the above step, display goes back to live view mode (preview).
-21-
1.12 Capture: Rotate +/-90 degrees
OK
Playback
/captured image
User can apply the up/down button for further editing (rotate +90/-90). Once user
confirm rotate +90 degrees, they can press the OK button, the image will be rotate +90
degrees and cursor will remain at Save. Press OK button again will save the rotated
image to SD card and screen will return to live view. For continuously rotate +90 degrees,
move cursor to rotate again and press OK.
1.13 Capture: Cancel
Or select Cancel and press OK button to cancel any of the editing step with present
selected image and FilmScan35-II-2.4-TV out goes to live view mode (nothing will be
saved onto the SD card).
-22-
1.14 Capture: Home
Next image in
film cartridge
OK
Go back to main menu, press OK button when select Home icon.
1.15 Exit from Edit mode back to Capture mode (Live View)
Once User presses OK button for save or cancel option, display will return to capture
mode/live view. Then, user can move the film cartridge to next target film to capture.
-23-
1.16 Memory full
OK
SD card locked
indicator
Once the internal memory or SD card is full, user can see a SD card full once press OK
button. User has to down load the images to PC or replace another SD card for continue
capture.
1.17 SD card locked
If the SD was locked, once press the OK button, a SD Card locked icon displays on screen.
Please do slide the switch of SD card to unlock before insert into device.
-24-
1.18 SD card error
SD card error
indicator
If scanner cannot detect SD card in good condition, a warning icon with question mark
will be shown on display. Please try to format the SD card or replace another proper SD
card for continue further operation. (Refer to Setting section on page 31.)
FULL
-25-
2. Playback
Playback
Press Down button to Playback mode when power on FilmScan35-II-2.4-TV out or access
the main menu by Home icon if during operation. Press OK button to confirm the
selection.
2.1 Playback: Auto Slide Show
Slide show mode
Once user enter playback mode (default to slide show), 2.4 TFT will auto display all
images stored in SD card with 2 seconds interval from previous captured image. User can
also stop the slide show mode by press OK button.
-26-
2.2 Playback: Edit Menu
Save
Hom
Rotate +90
Exit
Delete
Rotate -90
Mirror
Flip
●
●
●
●
●
●
●
●
Rotate +90: captured image rotate +90 degrees
Rotate -90: captured image rotate -90 degrees
Mirror: change image left to right
Flip: upside down image
Exit: returns to Slide show
Delete: delete this picture stored in SD card
Save: save the modified image onto SD card
Home: returns to main menu
2.3 Playback: Slide mode -> Edit mode
User can interrupt (stop) the slide show mode to stand alone playback mode (single
picture playback) by press OK button. (Pause slide show) Then user is able to scroll each
picture by up/down button. Once user select the picture stored in SD card which intended
to be modified, then use OK button again to bring out the edit mode for modification
-27-
2.4 Slide Show -> Single picture -> Edit mode
Pausse
OK
OK
Single picture mode
Use Up/Down button
to scroll picture to be modified
OK
Slide show mode Edit mode
2.5 Playback: Rotate/Mirror/Flip/Save
If user wants to Rotate +90 degrees by OK button, the image will be rotate +90 degrees
and cursor will remains at Save. Press OK button again to save modified result and next
picture will be shown (N+1). For continuously Rotate +90 degrees, move cursor to Rotate
again and press OK. (Same for Rotate -90, Mirror, and Flip function)
-28-
2.6 Playback: Exit
OK
OK
Once user select the EXIT function in edit menu, the display will go back to slide show
starting with the current picture in internal memory or SD card without saving any
change of present picture
2.7 Playback: Delete
Delete will delete the present selected picture and next picture will be shown (N+1).
Cursor goes to Exit icon. If user intend to process continuously delete, just move to delete
icon again and press OK to confirm.
-29-
2.8 Playback: Home
OK
OK
Go back to main menu, press OK button when select Home icon
2.9 Playback: No Picture
If there’s no picture inside internal memory or SD card when enter playback mode, a No
picture symbol will show on display.
-30-
3. Film Type
Slide film
B&W Negative
Color Negative
film
Film Type
Change film type definition by enter Film Type menu when power on FilmScan35-II-2.4-TV
out or access the main menu by Home icon if during operation. Press down button for
Film Type and press OK to confirm.
3.1 Film Type: Select Film Type
●
Negative film: select Negative film when cartridge loaded with negative film
●
Slide: select Slide type when load slide in holder
●
B&W film: select B&W when cartridge loaded with Black&White negative film
-31-
3.2 Film Type: Example
Color Negative
film
B&W
Negative film
Slide
Loaded
Into
Cartridge
-32-
4. USB Mode
USB mode
After finished capture, user can download the stored images from internal memory or SD
card to PC by selecting USB mode. Press OK button when connect USB cable to PC,
FilmScan35-II-2.4-TV out becomes a mass storage device. User can review or edit images
once PC detected the external storage device. Or just take out the SD card from device
into PC to read the images directly.
4.1 USB Mode: Status
Once user select USB mode, FilmScan35-II-2.4-TV out becomes a mass storage device and
then a status icon shows on display, then user can find an external USB disk device from
my computer and review the images in internal memory or SD card with PC.
-33-
5. Setting Mode.
Setting mode
TV out
Format
Exit
The setting mode covers TV out and format option. User can connect the device to TV
and finish the operation with TV display. Moreover, the scanned images can be playback
on TV display to share with family.
If the SD card was formatted by the other devices and not readable by scanner, user can
apply the format function in scanner to correct required format.
5.1 Setting Mode
●
●
●
TV out: select NTSC or PAL according to required interface
Format: format internal memory or SD card
Exit: returns to main menu
-34-
5.2 Setting: TV out
OK
OK
When user want to switch the display from on device LCD to TV display, user can connect
device to TV and select PAL or NTSC as required in TV out menu by OK button. Then, the
TV display will show the same option for scanning operation. Or directly enter playback
mode to slide show captured images on TV.
5.3 Setting: Format
If the internal memory or SD card requires format by scanner, user can enter format
mode by press OK button. The default setting will be cancel format. User can press OK
button again to cancel the format or select confirm icon to confirm format the memory.
Note
If there’s no SD card inside device, the internal memory will be formatted once process
Format. Instead, if SD card is inserted in device, SD card will be formatted.
-35-
Good bye page
-36-
V. Specification
Image Sensor:
9 mega CMOS sensor
Lens:
Precision TM Glass Element Fixed Focus
LCD:
2.4’’ Color TFT LCD (2.5” optional)
Internal memory:
24MB NAND Flash (for saving images)
Focus Range:
Fixed focus
Exposure Control:
6 levels of control
Color Balance:
6 levels of control
Scan Quality:
2,400 dpi
Data Conversion:
10 bits per color channel
Scan Method:
Single pass
Light Source:
Back light (3 white LEDs)
Interface:
USB 2.0, TV-out (video 3.5mm jack)
USB Configuration:
Mass Storage Device Class/MSDC
Power:
5V adapter, or USB power
Dimensions:
82x86x152mm
Weight:
0.41kg
External memory:
SD/MMC compatible
-37-
NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment under FCC rules.
- 38 -
Loading...