Page 1
MODELNO.
SLGU / SLLV Range
874/2012
LAMP REPLACEMENT:
1. Switch o the electricity at the mains.
2. Pull the bezel o the front of the tting.
3. Pull the bezel o the front of the bulb
4. Turn the lamp anti-clockwise to remove from the
lampholder.
5. Fit a new lamp.
REPLACEMENT LAMP TyPE:
• MAINS requires 1 x GU10 PAR16 energy saving lamp
(not included)
• LOW VOLTAGE requires
saving lamp (not included)
• Fittings are rated at 50W max.
Issue 2013
1 x GU5.3 MR16 energy
FOR PRODUCT ADVICE:
• T: 01933 673 144
• F: 01933 678 083
• E: [email protected]
CLEANING:
Clean this light tting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
Do not use any chemical or abrasive cleaners.
EVENTUALLy, yOU MAy WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
IF yOU ExPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
0.5M
Visit our website:
www.eterna-lighting.co.uk
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
GU10
Pack contents:
1 x Fitting
Model:
SLGUCR / SLGUSN / SLGUWH
SLLVCR / SLLVSN / SLLVWH
Mains / Low Voltage IP65 Shower Light
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
GU5.3
Page 2
READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product contains glass, care must be taken when
assembling, tting or handling to prevent personal
injury or damage to the product.
This light tting must be installed by a competent
person in accordance with the Building Regulations
making reference to the current edition of the
IEE Wiring Regulations (BS7671). The Building
Regulations may be obtained from OPSI or viewed
and downloaded from www.communities.gov.uk
following the link for Building Regulations.
As the buyer, installer and/or user of this produc t it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
This product is designed and constructed according
to the principles of the appropriate British Standard
and is intended for normal domestic service. Use of
this tting in any other environment, for example
where prolonged periods of use may be expected
and/or higher than normal ambient temperatures,
may result in a foreshortened working life.
Switch o the mains before commencing installation
and remove the appropriate circuit fuse.
When working at heights, please use a suitable
platform.
Suitable for indoor use only.
This product is suitable for use in living areas, and
Bathroom zones 1 and 2 (see diagram below and
current IEE Wiring Regulations for details). If being
tted in a bathroom a 30mA RCD must be used.
Bathroom Zones Diagram
ZONE 1
ZONE 2
ZONE 2
225cm
60cm
radius
from tap
This product is suitable for installation on surfaces
with normal ammability e.g. wood, plasterboard,
masonry. It is not suitable for use on highly
ammable sur faces (e.g. polystyrene, textiles).
ZONE 0
60cm240cm
If installing/mounting a light tting to a plastic
ceiling, you must seek advice from the ceiling
manufacturer regarding the type and specication
of light ttings that may be used. Light ttings that
generate and retain heat such as halogen downlights
or ush ttings with incandescent lamps, may
damage or discolour a plastic ceiling.
Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
Do not cover the t ting with any insulating materials.
The lamp must be positioned so that there is at least
0.5m (500mm) between the bulb and any illuminated
surface. Spotlights should be positioned well away
from curtains and beds to ensure this distance is
maintained.
Do not attach to surfaces which are damp, freshly
painted or otherwise electrically conductive (e.g.
metallic surfaces).
If the location of your new t ting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the Building
Regulations making reference to the current edition
of the IEE Wiring Regulations (BS7671).
This product is designed for permanent connection
to xed wiring: this should be either a suitable
lighting circuit (protected with a 5 or 6 Amp MCB or
fuse) or a fused spur (with a 3 Amp fuse) via a fused
connection unit. We recommend that the supply
incorporates a switch for ease of operation.
Make connections to the electrical supply in
accordance with the following code:
Live: Brown or Red
Neutral: Blue or Black
When making connections, ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation. Wrap loose terminal blocks well with
insulating tape.
This tting is double insulated; do not connect any
part to ear th.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out:
these tests are specied in the Wiring Regulations
(BS7671) referred to in the Building Regulations.
INSTALLATION:
01. Choose the location for your new tting
according to the conditions listed above.
02. Cut a hole of 70mm diameter in your ceiling,
Fig 1.
03. Undo the screw in the centre of the terminal
block and lift o the cover.
04. Make the connections to your mains supply. Note
that the terminals are not polarised i.e. you may
connect either Live or Neutral (Brown or Blue)
wires to either terminal.
05. Attach the bracket complete with terminal block
to the body of the tting and secure using the
screw supplied, Fig 2.
06. Holding the spring clips upwards and with the
lampholder hanging down through the middle,
oer the body of the tting into the hole and
allow the springs to pull the tting up to the
ceiling, Fig 3.
07. Fit a suitable lamp to the lampholder, insert and
turn clockwise until it stops.
08. Clip the lamp into the three clips in the back of
the bezel, Fig 4.
09. Press the bezel, complete with lamp, up into the
tting until pressed fully up to your ceiling, Fig 5.
10. Restore the power and switch on.
Fig 3
Hole
Fig 1
ø70mm
Fig 2
Fig 4
Fig 5
Loading...