ETC Paradigm P-LCD Series Installation Manual

Page 1
ETC® Installation Guide
Unison Paradigm Touchscreen Rack Panel
.cnI ,slortnoC ertaehT cinortcelE4 fo 1 egaPlenaP kcaR neercshcuoT mgidaraP nosinU
Corpora te Headquarters
3031 P leasant View Road, P.O. Box 620979 , Middleton, Wisconsin 53562-0 979 USA Tel +608 831 411 6 Fax +608 836 1736
Unit 26-28, Vi ctoria Industrial Estate, Victoria Road, London W3 6UU, UK Tel +44 (0)20 88 96 1000 Fax +44 (0)20 8896 20 00
Rome, IT
Via Ennio Quirino Visconti, 11, 00193 Rome, Italy Tel +39 (06) 32 111 683 Fax +4 4 (0)20 8896 2000
Holzkir chen , DE
Ohms trasse 3, 83607 Holzkirc hen, Germa ny Tel +49 (80 24) 47 00-0 Fa x +49 (80 24 ) 47 00-3 00
Hong Kon g
Rm 1801, 18/F, Tower 1 Ph ase 1, Enterpr ise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kon g Tel +852 2799 122 0 Fax +852 2799 9325
Service:
(Amer icas) service@e tcconnect.com (UK) service@etceur ope.com (DE) techserv-ho ki@etcconnect.co m (Asia) service@etcasia.com
Web:
www.etcconnect.com
Copyright © 2009 ETC. All Rights Reserve d. Product inf ormation and specifications subject to change.
7184M21 20
Rev B Rel eased 200 9-12
ETC intends this d ocument to be provided in its entirety.
Overview
The Unison® Paradigm™ Touchscreen uses a high-resolution, 7”-wide screen, color liquid-crystal display (LCD) that is bright and easy to read, with controllable back lights. The Touchscreen is installed in a rack panel, which is shipped separately. The Touchscreen is also available in locking cover and wall mount configurations. The Touchscreen is powered by either LinkPower and Auxiliary power or PoE (Power Over Ethernet 802.3af).
Echelon® LinkPower® (LinkConnect) control network utilizing Belden 8471 (or approved equal) and 24 Vdc Auxiliary power (two 16 AWG 1.5mm2) wires.
PoE (Power over Ethernet 802.3af) utilizing Category 5 cable (or approved equal).
All control wiring should be installed and terminated by a qualified installer and should follow standard wiring installation practices. Leave approximately 10 inches (254mm) of wiring in the backbox for connection and to allow slack for future service needs. For more information about terminating Cat5 cable, refer to the ETC Ethernet Cat5 Termination Kit Setup Guide.
Installing the Collar
Installation should follow local codes and standard practices. Ensure that all wiring is installed correctly. The touchscreen is su
pplied with an installation kit which includes the necessary hardware and
electrical supplies.
Step 1: Slide the collar into the rack panel.
Step 2: Install and tighten four M4 x 20mm collar mount screws through the collar into the rack
panel.
Paradigm Touchscreen Model
noitpircseDledoM
P-LCD-RBB Paradigm Touchscreen rack panel
Note:
It is important to orient the rack panel with the cutout on the right side to provide better cable access between the Touchscreen and the Termination PCB. As well the collar should be installed with the double mounting pin on the top.
Page 2
ETC Installation Guide
Paradigm P-LCD Series
Unison Paradigm Touchscreen Rack Panel Page 2 of 4 Electronic Theatre Controls, Inc.
Installing the Termination PCB
The printed circuit board (PCB) assembly is designed to accommodate either Ethernet or LON connections. Prior to installing the PCB, terminate all necessary wiring. The PCB is installed on the back side of the rack panel.
The PCB consists of three parts:
• PCB with female RJ11, LinkPower connector, 24 Vdc (Aux) connector, and ground spade
• RJ45 with punch down wire termination
• Mounting bracket and screws
Connecting Ethernet
Step 1: Terminate the network wiring in the RJ45 punch down strip using a standard 110 punch
down tool (not provided). Reference the connector label for the CAT5e wire termination color code. The punch down connector provides insulation displacement. Do not strip the wires.
Step 2: Snap the RJ45 connector into the bracket.
Connecting LinkPower and Auxiliary Power
Use the provided WAGO CAGE CLAMP® connectors to terminate the wiring to the provided LinkPower (black and white twisted pair) and Auxiliary power (red and black twisted pair) and ground wire pigtails. Strip the ends of each wire (both installed control wires and pigtail wires) approximately 3/8” (10mm).
Step 1: Terminate the installed LinkPower wiring to the white and black LinkPower pigtail. Using
two Wago connectors connect (typically white) installed wire(s) with white pigtail wire and connect the (typically black) installed wire(s) with black pigtail wire as shown below.
CAUTION:
Only one network type may be connected to the touchscreen. Damage will occur if both power types, Auxiliary power and PoE, are connected to the Touchscreen.
ETC requires that all backboxes are grounded in accordance with local electrical codes.
The RJ11 connection must be used to provide a ground connection from the backbox to the touchscreen even when Ethernet connectivity is used.
Note:
All Ethernet terminations must follow IEEE 802.3 and be terminated to the T568B standard.
Ground spade
PCB
24 Vdc Aux
power
connector
RJ45
Mounting bracket
ULP connector
RJ45 Ethernet with
(PoE to Touchscreen)
RJ11 connector
(provides LinkPower and
Aux power to Touchscreen)
topology of a single
station installation
topology of multiple stations installed in
series
Installed control wire
Pigtail wire
Installed control wire Installed control wire to next station Pigtail wire
Page 3
ETC Installation Guide
Paradigm P-LCD Series
Unison Paradigm Touchscreen Rack Panel Page 3 of 4 Electronic Theatre Controls, Inc.
Step 2: Plug the LinkPower connector into the two pin LinkPower receptacle on the termination
PCB.
Step 3: Terminate the installed Auxiliary power wire to the red and black Auxiliary power pigtail
wires. Using two Wago connectors connect the (typically red) installed wire(s) with red pigtail wire and connect the (typically black) installed wire(s) with black pigtail wire.
Step 4: Plug the Auxiliary power connector into the two pin Aux power receptacle on the
termination PCB.
Installing the Termination PCB to the Rack Panel
Step 1: Position the PCB on the four standoffs on the back of the rack panel and secure with two
M3x10mm pan head screws on the RJ11 side of the PCB only.
Step 2: Place the bracket and RJ45 assembly (if used) on top of the PCB. Secure the PCB to the
backbox through the remaining holes in the PCB with two M3x10mm pan head screws.
Step 3: A ground connection is required for all Touchscreen assemblies. Using one three position
Wago connector, connect the (typically green and yellow) installed wire(s) with the ground wire pigtail (with attached spade), provided in the installation kit, and the ground wire attached to the rack panel.
Note:
The termination PCB can be installed in any orientation to accommodate wiring.
Installed ground wire Ground wire pigtail (spade connector to the termination PCB) Ground wire pigtail (ring terminal connected to the rear rack panel)
Page 4
ETC Installation Guide
Paradigm P-LCD Series
Unison Paradigm Touchscreen Rack Panel Page 4 of 4 Electronic Theatre Controls, Inc.
Installing the Touchscreen
Step 1: Install the RJ11 control cable provided in the installation kit to the RJ11 jack on the
termination PCB. Also attach the RJ45 control cable if PoE will be used for communication and power.
Step 2: Plug the other end of the cable(s) into the receptacles on the Touchscreen. Step 3: Hold the Touchscreen at a slight angle and insert the top first and hook the bracket onto
the double pins on each side of the collar.
Step 4: To move the Touchscreen from the service position to the operation position, lift up at the
bottom and rotate the bottom inward.
Step 5: Push firmly in and down on the bottom corners of the bezel until it audibly snaps onto the
collar. When properly installed, the Touchscreen should not easily unsnap from the collar.
Step 6: To open or remove the Touchscreen, insert a flat bladed screwdriver into the pry slots and
unsnap the Touchscreen from the collar. Then lift the bottom upward slightly and rotate outward.
Indicators
After the Touchscreen has been powered up, the appropriate LEDs on the service panel on the bottom of the Touchscreen illuminate. The LCD displays a startup screen a few seconds after booting.
I/O Indicators
Reset - when pressed, resets the Portable LCD software
Mode - press once for Setup menu. Press and hold for 4 seconds to calibrate the Touchscreen
PoE - indicates when the Touchscreen is powered by Power over Ethernet 802.3af
Aux - indicates the Touchscreen is powered (Aux 24 Vdc)
Act - application activity is detected
Svc - when pressed, sends the stations Neuron ID to the connected processor
Svc - service pin indicator
Data (LON) - indicates LON network activity
Link - indicates when the Ethernet interface has a valid link to the network
Data (NET) - indicates Ethernet network activity
Note:
The RJ11 cable provides the ground connection to the rack panel and must always be installed.
Service position
Operating position
The Touchscreen bracket is designed for two positions, service and operation. When installed so that the pins are in the first slots on the bracket, the Touchscreen is angled at the bottom for service.
SD card slot
USB Port
Pry slot
Pry slot
Loading...