Escalade sports P1261 User Manual

OWNER’S MANUAL

HERITAGE 8FT. DROP POCKET POOL TABLE

MODEL NO. P1261

1. READ THIS MANUAL CAREFULLY BEFORE STARTING ASSEMBLY.
Read each step completely before beginning each step.

2. SOME SMALLER PARTS MAY BE SHIPPED INSIDE LARGER PARTS. CHECK INSIDE ALL PARTS
AND CARTONS BEFORE ASSEMBLING OR ORDERING PARTS.

3. USE THE HARDWARE IDENTIFIER TO IDENTIFY AND SORT ALL FASTENERS. CHECK ALL CARTONS
FOR KITS. ALL HARDWARE IS NOT LOCATED IN ONE KIT.

THIS TABLE IS CONTAINED IN THREE SEPARATE CONTAINERS:

PLEASE DO NOT RETURN PRODUCT TO THE STORE!

Contact Escalade® Sports customer service department at:

Phone: [phone] Toll Free !

Fax: [phone]Toll Free !

E-mail: [e-mail]

Mailing Address: Escalade® Sports, PO Box 889, Evansville, IN 47706

Please visit our World Wide Web site at:

www.escaladesports.com

On-Line Trouble Shooting Frequently Asked Questions

Technical Assistance On-Line Parts Requests

Additional Escalade® Sports Product Information

Escalade® Sports products may be manufactured and/or licensed under the following patents.
D446275
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2L-6805-00

CAUTION

THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLOTH IS EXTREMELY FLAMMABLE AND UNDER
PRESSURE
CHILDREN
AREA

To ensure safety, do not attempt to assemble system without following instruc­tions carefully. Proper and complete assembly, use, and supervision is essential for
proper operation and to reduce the risk of accident or injury. A high prob­ability of serious injury exists if this system is not installed, maintained, and
operated properly.

! CAREFULLY READ CAUTIONS ON SPRAY ADHESIVE CONTAINER! KEEP OUT OF THE REACH OF

! DO NOT USE OR STORE NEAR HEAT SOURCE, FLAMES, SPARKS OR WHEN SMOKING! WORK

MUST BE WELL VENTILATED. OPEN DOORS AND WINDOWS WHEN USING SPRAY ADHESIVE.

Tools Needed: (Not Included)

• Hammer (Claw Type)

• Needle Nose Pliers

• Standard Screwdriver

• Phillips Screwdriver

• Power Screwdriver
(optional but very helpful)

NOTE: Rails are made with cushion rubber at a height that requires standard 2 1/4” diameter balls.
Your dealer has a complete line Billiard Accessories.

NOTE: This table adds weight to any floor. Be sure floor can withstand this kind of weight. If floor sags,
table will be impossible to level.

• Putty Knife

• Tape Measure

• Sanding Block

• Awl or 8d Nail

• Scissors or Sharp Knife

• Sandpaper (80 grit)

• 3/8” Open End Wrench

• 7/16” Open End Wrench

• 1/2” Open End Wrench

• Hammer (Small Ball Peen Type)

• Carpenters Level or 36” Straight Edge

• Rachet with 3/8” and 1/2” sockets

ASSEMBLE TWO LEG PEDESTALS AS FOLLOWS:

1. Begin by opening hardware kits and sort hardware.

Attach two tube brackets #21 to each leg #20 using
screws #30 and the pre-drilled starter holes in leg #20.
(See Figure 1)

Figure 2

Figure 1

Figure 3

2. Connect two legs #20 together by putting two cross tubes #22

over tube brackets #21 between legs. Secure each tube with four
screws #29. See figure 2. Repeat for other two legs #20. NOTE:

Attach top tube first, with screws #29, from one side and
top of tube. Attach bottom tube second with screws #29
from same side as top tube and bottom of tube.

3. Set up leg assemblies so that screws attaching cross tubes face

each other. See figure 3.

Page

3

Figure 4

5. Attach beam #15 by using three bolts #40, six washers #50, and three

locknuts #49 for each of the legs post #20. Place one washer between
the bolts and leg and one between beam and locknuts. Tighten these
bolts securely. (See figure 4)

6. Attach other beam #15 to the other side the same way. (See figure 4)

Make sure the holes in the edge of the beams #15 are on the top of

the beams when attached.

7. Place the frame in its final location. Square

the base frame assembly by measuring
diagonally from the corner of one beam to
the opposite corner of the other beam. (See
Figure 5) Nudge the frame until both diago­nals are equal (within 1/16 inch).

8. Go back and tighten all loose screws, nuts

and bolts.

Top View

Page

4

Figure 5

Figure 6

9. Place long slats #16 (50 inches long) and short slats #17 (36 inches long) across table from beam to beam as shown

in figure 6. Make sure to use the two shorter slats #17 on the ends of the beams and the two longer slats #16 in the center
as shown. Insert four dowel connectors #36 into the four holes in the side of each of the beams #15 these holes should be
closer to the top of the beams #4. (See Detail A). Attach the slats #16, and #17 to the wooden beams #15 by placing
screws #18 through the slats and into the dowel connectors #36 that are in the beams #15 and tighten, make sure not to

over tighten them. (See figure 4 and detail A))

HINT: When holes are lined up, the slot in the dowel connector should be vertical. After holes line up, insert screws #18 into

slats and down into dowel connectors. It is recommended to start the screws by hand and not forcing them with power tools
until you are sure threads are engaged properly. Do not tighten completely yet.

10. Attach cross supports #22 to inside surface of legs, as shown in figure 6, using four screws #45 for each cross support. NOTE:
No pilot holes are provided for screws #45. Hold cross support approximately 1/2" from top of leg and drive
screws #45 through holes in cross support and into leg.

Figure 7

11. Square up the long slats #16 by measuring

diagonally, similar to the method used ear­lier to square up base frame. (See Figure 7)
After squaring up slats, tighten all the screws
holding slats #16 and #17 to the beams.

Top View

Page

5