Escalade sports P1087 User Manual

OWNER'S

MANUAL

OWNER'S

MANUAL

SERVICE

DROP POCKET 8 FT. SLATE

HOME POOL TABLE

Thank you for buying our product. We try hard to insure that our products
are of high quality and free of problems, such as manufacturing defects or
missing parts. However, if you have any problems with your new product,
please call us at:

Or write us at:

CUSTOMER SERVICE DEPARTMENT

P.O. Box 889, Evansville, IN 47706

MODEL NO.

P1087

WARRANTY

Or E-mail us at: [e-mail]

Please provide model number, serial number, and/or part number of the
product and/or part when you call or write. These numbers can be found on
the product, packaging, and/or in this Owner’s Manual.

ONE YEAR WARRANTY ON POOL TABLE

Manufacturer warrants to the original retail purchaser, this product to be free from
defects in material and workmanship for a period of one (1) year from the date of
purchase.

TEN YEAR WARRANTY ON SLATE SURFACE

For ten (10) years from the date of purchase, we will repair the playing surface of
this table, free of charge, if it fails to remain flat, within a tolerance of ± 20/1000 of
an inch, measuring from any flat plane within the playing surface. Note: Cloth not
included in warranty.

Should this product become defective due to material or workmanship within the
warranty period, contact our Customer Service Department. This warranty is not
transferable and does not cover normal wear and tear, or damage caused by improper
handling, installation or use of this product. This warranty is also void if product is
in any way abused, damaged, or modified from its original state, or if used for other
than indoor residential use. This warranty gives you specific legal rights, and you
may have other rights which vary from state to state.

2L-6638-00

IMPORTANT! READ THIS MANUAL
ALL THE WAY THROUGH BEFORE
BEGINNING TO PUT YOUR POOL
TABLE TOGETHER! THEN READ
EACH STEP BEFORE STARTING THAT
STEP.

This table has been inspected to insure proper fit. The bed is made of ¾ inch thick slate.
Carefully unpack and examine each shipping container and its packing material before
discarding to assure all parts have been removed. Some smaller parts may be shipped inside
larger parts. Check inside parts before assembling.

This table is contained in three separate containers:

Container #1. . . . . . Three slate pieces

Container #2. . . . . . Contains this owner's manual, leg assemblies, hardware kits, corner & side caps,

corner posts, playfield spots, slate shims, glue and grout kit and drop pockets.

Container #3. . . . . . Contains long and short slats; beams, top rails; aprons; playfield cloth, and

additional hardware

Tools Needed ! Carpenter's level & 36'' Straight Edge

! 3/8" Open End Wrench ! Hammer (Small Ball Peen Type) ! Needle Nose Pliers
! 7/16" Open End Wrench ! Tape Measure ! Standard Screwdriver
! 1/2" Open End Wrench ! Sanding Block ! Phillips Screwdriver
! Putty Knife ! Power Screwdriver (optional BUT very ! Scissors
! Awl or 8d Nail helpful)

In addition to the assembly tools listed above, it would be useful to have a rachet with 3/8, 7/16 and 1/2 sockets
and an electric screwdriver.

NOTE: Rails are made with cushion rubber at a height that requires 2 ¼" diameter balls. Your dealer has a complete

line of Billiard Accessories.

NOTE: This table adds weight to any floor. Be sure floor can withstand this kind of weight. If floor sags, table will

be impossible to level!

THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLOTH IS
EXTREMELY FLAMMABLE AND UNDER PRESSURE! CAREFULLY
READ CAUTIONS ON SPRAY ADHESIVE CONTAINER! KEEP OUT

OF REACH OF CHILDREN! DO NOT USE OR STORE NEAR HEAT
SOURCE, FLAMES, SP ARKS OR WHEN SMOKING! WORK AREA
MUST BE WELL VENTILATED. OPEN DOORS AND WINDOWS
WHEN USING SPRAY ADHESIVE.

2

3

Figure 1

1. Attach wood facades #14 to Leg Post #19 by inserting
two screws #32 and two washers #21 through holes in
leg and into pilot holes in facade. Bottom of leg and
facade should be flush. Tighten securely and repeat for
the remaining three leg assemblies. See Figure 1.

2. Attach Leg Panel #13 to leg post by butting one end
to wood facade #1, and making sure the bottom is
flush with the leg post. Wood grain faces out.
Fasten with three screws #22. Attach the other end
of the leg panel to another leg assembly, making
sure the facade faces out.

Repeat for the other leg assembly.

Figure 2

Figure 3

3. Attach the wooden beam #15 by
using four bolts #27, eight wash­ers #50, and four locknuts #49
as shown. Make sure that the
holes in beam #15 face up as
shown. (Figure 3)

4

Figure 4

Detail A

Detail B

4. Place slats #16 and #17 across table from beam to beam as shown in figure 4.
Make sure to use the two shorter slats #17 on the ends of the beams and the two
longer slats #16 in the center as shown. Insert four dowel connectors #36 into the
holes in side of each of the beams #15 (See Figure 4 and Detail B), these holes
should be closer to the top of the beams #15. To attach slats #16 and #17 to the
wooden beams #15, see the following procedure noted: "Hint"

HINT: If the screwdriver slot in the dowel connector #36 is straight up and down,
and you can see the threaded bolt hole in the dowel connector #36 through the hole in the top of beam #15, the
dowel connector #36 is lined up. (See detail A) It is recommended to start the bolts by hand and not force them
with power tools until you are sure threads are engaged properly. After holes line up, insert screws #18 into slats
and down into dowel connectors (See detail B). Do not tighten completely yet.

5. Square up long slats #16 by measuring diagonally from end
to end as shown in figure 5. Check to make sure the table
is square. Then tighten screws into the dowel connectors.

Figure 5

5