Escalade sports G05952 User Manual

We strive to ensure that our products are of the highest quality

and free of manufacturing defects or missing parts. However, if

you have any problems with your new product,

DO NOT RETURN IT TO THE STORE,

please contact us toll free @:

1-866-556-2759

FAX: [phone]

[e-mail]

Or write to:

Escalade Sports

Customer Service Department

P.O. Box 889

Evansville IN 47706

Please have your model number when inquiring about parts.

When contacting Escalade Sports please provide your model number , serial number (if
applicable), and part number if requesting a replacement part. These numbers are
located on the product, packaging, and in this owners manual.

Y our Model Number _______________________

G05952

IMPORTANT! READ THIS MANUAL ALL THE
W AY THROUGH BEFORE BEGINNING TO PUT
YOUR GAME TABLE TOGETHER! THEN READ
EACH STEP BEFORE ST AR TING THA T STEP.

TWO ADULTS ARE REQUIRED TO ASSEMBLE

THIS GAME TABLE

Tools Needed

Philips Screwdriver
Adjustable Wrench or Socket Set
Furniture Polish and Cloth

An electric screwdriver is helpful in assembly. However, please use extreme caution with an electric
screwdriver because you could overtighten the hardware and strip the screws.

IMPORTANT!

Make sure you understand the following tips before you begin to assemble your soccer table.

1. When installing parts that have more than one bolt, start ALL the bolts in that part by hand
before tightening anything.

2. When the table is complete the Goalie Rod should be on your left when standing on either side
of the table. The assembly is done with the table up-side-down. This means everything is
opposite until the table is turned right-side-up.

3. If your table model has push on type handles you cannot pull them off once installed. Make sure
the rods are correct and you are installing the handle on the correct end of the rod.

4. Do not tighten hardware until the instructions indicate so.

5. Do not overtighten hardware, as you could damage the finish on the table

6. Some drawings or images in this manual may not look exactly like your product.

7. You can apply spray furniture polish to a cloth and wipe down the rods to make them slide
more easily in the bearings.

READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND

SAFETY INSTRUCTIONS CAREFULL Y. AT LEAST TWO

ADULTS ARE NEEDED T O PUT THIS GAME TABLE

TOGETHER!

© 2002 Escalade Sports

2 For Customer Service Call 1-866-556-2759

© 2002 Escalade Sports

3 For Customer Service Call 1-866-556-2759

© 2002 Escalade Sports

4 For Customer Service Call 1-866-556-2759

© 2002 Escalade Sports

5 For Customer Service Call 1-866-556-2759

© 2002 Escalade Sports

6 For Customer Service Call 1-866-556-2759

© 2002 Escalade Sports

7 For Customer Service Call 1-866-556-2759

Before starting your table assembly you need to assemble the players onto the rods.

Use the parts listed on page 6 of this manual and assemble in the order shown below .

Start with one color and assemble one team first. You will need one 5 player rod C1, one 2 player
rod C3 and two 3 player rods C2. First identify the handle end of the rod, the handle end of the rod
has a hole close to the end of the rod.

Holding the rod from the handle end assemble the players as shown in the diagram above. Use the
number of players needed for the rod you are working on. Remember to face all players the same
direction as you install them on the rod.

© 2002 Escalade Sports

8 For Customer Service Call 1-866-556-2759

1. Find a clean, level place to begin the assembly of your
game table. We recommend building the table on the
box top to protect the parts during assembly.

2. Place one side panel P3
side facing out as shown. The ball entry hole will be
closest to the floor.

upside down

with the finished

Figure 1

3. Align the rods as shown in Figure 1. Choose one team to be color # 1 and one team to be color # 2. The handle end of
the rod has a hole close to the end of the rod. There will be four handles (one team) on each side of the table. Remember,
the goalie rod is always in your left hand when the table is in the upright position and you are working upside down so it will
be opposite during assembly.

Figure 2

4. Once you are sure you have the players set
up correctly, slide the other side panel P3 on
the other end of the rods as shown.

5. Set the playfield P5 onto the assembly with
the graphics facing down. Insert the playfield
into the groves on the side panels.

6. Place the playfield support braces P7 on the
bottom of the playfield as shown in Figure 3.
Slide the playfield support rods H11 through
the side panel and the grove in the support
braces. Secure with washers H4 and finishing
nut H5.

DO NOT TIGHTEN AT THIS TIME!

7. Attach the two end panel tops P4A as shown in
Figure 3 using bolts H1 and washers H2.

Remember to start all bolts by hand first
before you tighten anything.

Figure 3

© 2002 Escalade Sports

MAKING SURE END PANELS ARE STRAIGHT
TIGHTEN ALL HARDWARE AT THIS TIME.

8. Center the playfield P5 and secure to the end
panels using screws H8. DO NOT OVER

TIGHTEN SCREWS.

9 For Customer Service Call 1-866-556-2759