Escalade sports G05951 User Manual

We strive to ensure that our products are of the highest quality

and free of manufacturing defects or missing parts. However, if

you have any problems with your new product,

DO NOT RETURN IT TO THE STORE,

please contact us toll free @:

1-866-556-2759

FAX: [phone]

[e-mail]

Or write to:

Escalade Sports

Customer Service Department

P.O. Box 889

Evansville IN 47706

Please have your model number when inquiring about parts.

When contacting Escalade Sports please provide your model number , serial number (if
applicable), and part number if requesting a replacement part. These numbers are
located on the product, packaging, and in this owners manual.

Y our Model Number _______________________

G05951

IMPORTANT! READ THIS MANUAL ALL THE
W AY THROUGH BEFORE BEGINNING TO PUT
YOUR GAME TABLE TOGETHER! THEN READ
EACH STEP BEFORE ST AR TING THA T STEP.

TWO ADULTS ARE REQUIRED TO ASSEMBLE

THIS GAME TABLE

Tools Needed

Philips Screwdriver
Adjustable Wrench or Socket Set
Furniture Polish and Cloth

An electric screwdriver is helpful in assembly. However, please use extreme caution with an electric
screwdriver because you could overtighten the hardware and strip the screws.

IMPORTANT!

Make sure you understand the following tips before you begin to assemble your soccer table.

1. When installing parts that have more than one bolt, start ALL the bolts in that part by hand
before tightening anything.

2. When the table is complete the Goalie Rod should be on your left when standing on either side
of the table. The assembly is done with the table up-side-down. This means everything is
opposite until the table is turned right-side-up.

3. If your table model has push on type handles you cannot pull them off once installed. Make sure
the rods are correct and you are installing the handle on the correct end of the rod.

4. Do not tighten hardware until the instructions indicate so.

5. Do not overtighten hardware, as you could damage the finish on the table

6. Some drawings or images in this manual may not look exactly like your product.

7. You can apply spray furniture polish to a cloth and wipe down the rods to make them slide
more easily in the bearings.

READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND

SAFETY INSTRUCTIONS CAREFULL Y. AT LEAST TWO

ADULTS ARE NEEDED T O PUT THIS GAME TABLE

TOGETHER!

© 2002 Escalade Sports

2 For Customer Service Call 1-866-556-2759

© 2002 Escalade Sports

3 For Customer Service Call 1-866-556-2759

© 2002 Escalade Sports

4 For Customer Service Call 1-866-556-2759

© 2002 Escalade Sports

5 For Customer Service Call 1-866-556-2759

© 2002 Escalade Sports

6 For Customer Service Call 1-866-556-2759

1. Find a clean, level place to begin the assembly
of your game table. We recommend building the
table on the box top to protect the parts during
assembly.

Figure 1

2. Place one side panel P1
finished side facing out as shown. The ball entry
hole will be closest to the floor. Attach the end
panels P3 to the side panel using bolts H3 and
washers H2 as shown in Figure 1.

upside down

with the

Do not tighten at this time.

Leave hand tight until you complete

the following steps.

Figure 2

3. Align the rods as shown in Figure 2. Choose one team to be color # 1 and one team to be color # 2. The handle end of
the rod has a hole close to the end of the rod. There will be four handles (one team) on each side of the table. Remember,
the goalie rod is always in your left hand when the table is in the upright position and you are working upside down so it will
be opposite during assembly.

In the following steps start all hardware

by hand before you tighten anything.

4. Set the playfield P4 in place with the graphics
facing down as shown in Figure 3.

Figure 3

© 2002 Escalade Sports

7 For Customer Service Call 1-866-556-2759

Figure 4

5. Slide the other side panel P1 onto the rods as
shown in Figure 4. Attach the side panel with
bolts H3 and washers H2.

MAKING SURE END PANELS ARE STRAIGHT
TIGHTEN ALL HARDWARE AT THIS TIME.

6. Center the playfield P4 and secure to the end
panels using screws H9 as shown in Figure 4.

7. Place the playfield supports P5 onto the playfield.
Slide the cabinet rods H10 through the side panel,
down the channel of the playfield supports and
through the other side panel. Attach cabinet
rods using washers H7 and finishing nuts H6.

Figure 5

Figure 6

8. Set the main cabinet P9 upside down on a clean
surface as shown in Figure 6.

9. Attach the legs P10 to the main cabinet using
bolts H1 and washers H7 as shown in Figure 6.

© 2002 Escalade Sports

8 For Customer Service Call 1-866-556-2759

Figure 7

THIS STEP REQUIRES TWO OR MORE ADULTS.

VERY CAREFULLY TURN THE TABLE OVER AND
SET IT ON ITS LEGS. BE CAREFUL, THE TABLE
IS VERY HEAVY.

10. Carefully turn over the previously assembled soccer table as shown in Figure 7. Attach the rod handles P7 to the ends of the
rods that have a hole close to the end. Attach the rod end caps P8 to the other end of the rods. Attach the ball entry cup P2
to the side panels using screws H4. Next attach the soccer scorers P6 to the end panels using screws H5.

Figure 8

11. Carefully place the soccer table on the billiard table as shown in Figure 8. If the table does not fit squarely on the billiard table
you will need to loosen the H3 bolts that hold the end and side panels together on the soccer table to adjust it to fit the billiard
table.

© 2002 Escalade Sports

9 For Customer Service Call 1-866-556-2759