Escalade Sports G03605 User Manual

We strive to ensure that our products are of the highest quality

and free of manufacturing defects or missing parts. However, if

you have any problems with your new product,

DO NOT RETURN IT TO THE STORE,

please contact us toll free @:

1-866-556-2758

FAX: [phone]

[e-mail]

Or write to:

Escalade Sports

Customer Service Department

P.O. Box 889

Evansville IN 47706

Please have your model number when inquiring about parts.

When contacting Escalade S port s please provide your model number, serial number (if
applicable), and part number if requesting a replacement part. These numbers are
located on the product, packaging, and in this owners manual.

Y our Model Number _______________________

© 2003 Escalade Sports

G03605

1

For Customer Service Call 1-866-556-2758

IMPORTANT! READ THIS MANUAL ALL THE
WAY THROUGH BEFORE BEGINNING TO
PUT YOUR GAME TABLE TOGETHER! THEN
READ EACH STEP BEFORE STARTING
THAT STEP.

TWO ADULTS ARE REQUIRED TO ASSEMBLE

THIS GAME TABLE

Tools Required:

Wrench H6 Included with the Hardware Kit
Philips Screwdriver
Furniture Polish and Cloth

An electric screwdriver is helpful in assembly. However, please set at low torque and use
extreme caution with an electric screwdriver because you could overtighten the hardware
and strip the screws.

Assembly Tips

Make sure you understand the following tips before you begin to assemble your soccer table.

1. When installing parts that have more than one bolt, start ALL the bolts in that part by
hand before tightening anything.

2. Some drawings or images in this manual may not look exactly like your product. Please
read and understand the text before starting each assembly step.

READ AND FOLLOW ALL ASSEMBL Y, OPERA TION, AND

SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO

ADULTS ARE NEEDED TO PUT THIS GAME TABLE

TOGETHER.

© 2003 Escalade Sports

2

For Customer Service Call 1-866-556-2758

© 2003 Escalade Sports

3

For Customer Service Call 1-866-556-2758

1. Find a clean, level place to begin the assembly of your hockey table. We
recommend building the table on the box top to protect the parts during
assembly. Place the main cabinet P1 on the ground with the playing surface
facing down.

2. Using the wrench provided H6, attach the legs P2 to the main cabinet P1
using bolts H1, washers H2, and nuts H3 as shown in FIGURE 1. Leave
the hardware HANDTIGHT at this point.
Repeat this step for all four legs.

CAUTION:

DO NOT TIGHTEN LEG

HARDWARE AT THIS

TIME.

Figure 1

© 2003 Escalade Sports

4

For Customer Service Call 1-866-556-2758

3. Attach the end panels P3 to the inside of the legs using screws H4 as
shown in FIGURE 2. Make sure to center the panel and have it towards
the bottom of the legs as shown.

4. Attach the spreader P4 to the inside of the legs using screws H4 as shown
in FIGURE 2. Make sure to center the panel vertically on the legs as shown.

Figure 2

MAIN CABINET NOT SHOWN

5. T ighten all hardware at this time.

THIS STEP REQUIRES TWO OR MORE ADULTS.

VERY CAREFULLY TURN THE TABLE OVER AND SET IT ON
ITS LEGS. BE CAREFUL, THE TABLE IS VERY HEAVY.

FOR CLARITY.

© 2003 Escalade Sports

5

For Customer Service Call 1-866-556-2758

6. Feed the phone type plugs from under the table through the large holes in
the rail and plug them into the bottom of the electronics P5 as shown in
FIGURE 3. Attach the electronics P6 to the main cabinet using screws H5 as
shown in FIGURE 3.

Figure 3

Note: See page 7 for Operation of the Electroinics.

7. After you have attached the electronic unit, set the table where you want it
in your Game Room. Plug the cord into a suitable 120v household outlet
and turn the motor on by turning the switch that is built intothe cord.

© 2003 Escalade Sports

6

For Customer Service Call 1-866-556-2758