Escalade sports G01609 User Manual

We strive to ensure that our products are of the highest quality

and free of manufacturing defects or missing parts. However, if

you have any problems with your new product,

DO NOT RETURN IT TO THE STORE,

please contact us toll free @:

1-866-556-2759

FAX: [phone]

[e-mail]

Or write to:

Escalade Sports

Customer Service Department

P.O. Box 889

Evansville IN 47706

Please have your model number when inquiring about parts.

When contacting Escalade Sports please provide your model number , serial number (if
applicable), and part number if requesting a replacement part. These numbers are
located on the product, packaging, and in this owners manual.

Y our Model Number _______________________

© 2003 Escalade Sports

G01609

1

For Customer Service Call 1-866-556-2759

I

MPORTANT! READ THIS MANUAL ALL THE
WAY THROUGH BEFORE BEGINNING TO
PUT YOUR GAME TABLE TOGETHER! THEN
READ EACH STEP BEFORE STARTING
THAT STEP.

TWO ADULTS ARE REQUIRED TO ASSEMBLE

THIS GAME TABLE

Tools Required:

Allen Wrench H11 and H12 Included with the Hardware Kit
Phillips Screwdriver
Furniture Polish and Cloth

An electric screwdriver is helpful in assembly. However, please set at low torque and use
extreme caution with an electric screwdriver because you could overtighten the hardware
and strip the screws.

Assembly Tips

Make sure you understand the following tips before you begin to assemble your soccer table.

1. When installing parts that have more than one bolt, start ALL the bolts in that part by
hand before tightening anything.

2. Some drawings or images in this manual may not look exactly like your product. Please
read and understand the text before starting each assembly step.

READ AND FOLLOW ALL ASSEMBLY, OPERA TION, AND

SAFETY INSTRUCTIONS CAREFULLY . AT LEAST TWO

ADULTS ARE NEEDED TO PUT THIS GAME TABLE

TOGETHER.

© 2003 Escalade Sports

2

For Customer Service Call 1-866-556-2759

© 2003 Escalade Sports

3

For Customer Service Call 1-866-556-2759

© 2003 Escalade Sports

4

For Customer Service Call 1-866-556-2759

© 2003 Escalade Sports

5

For Customer Service Call 1-866-556-2759

1. Find a clean, level place to begin the assembly of your soccer table. We
recommend building the table on the box top to protect the parts during
assembly.

2. Place one side panel P1

UPSIDE DOWN

with the finished side facing out

as shown in FIGURE 1. The ball entry hole will be closest to the floor.

3. Align the rods as shown in FIGURE 1. Please note the location of the hole
that is near one end of each rod. This is the handle end of the rod. There
will be four handles on each side of the table. It is critical that you set the
rods as shown below so the table will be correct when flipped over .

Figure 1

Please set the rods as shown noting
the location of the hole / handle end.

© 2003 Escalade Sports

CAUTION:

6

For Customer Service Call 1-866-556-2759

4. Once you are sure you have the rods set up correctly, slide the other side
panel P1 onto the rods as shown in FIGURE 2.

5. Set the playfield P3 into the grooves in the side panels as shown in
FIGURE 2.

Figure 2

© 2003 Escalade Sports

7

For Customer Service Call 1-866-556-2759

6. Using the Allen wrench provided H11 attach the end panels P2 using bolts
H3 and washers H4 as shown in FIGURE 3. Remember to start all hardware
by hand before you tighten anything.

7. Next center the playfield in the cabinet and attach the playfield to using
screws H9 as shown in FIGURE 3. Do not over tighten these screws.

8. Once you have the playfield set, place the playfield support braces P6 on the
playfield and slide the playfield support rods H10 through the side panels and
down the groove of the playfield support brace. Secure the playfield support
rods with finishing nuts H5 and washers H8 as shown in FIGURE 3. Tighten
all hardware at this time.

Figure 3

© 2003 Escalade Sports

8

For Customer Service Call 1-866-556-2759

9. Using the Allen wrench provided H11 attach the legs P4 and P5 using bolts
H1 and washers H2 as shown in FIGURE 4. Have a helper hold the cross
bar P13 between the legs as you attach them to the table. See DETAIL for
FIGURE 4. Remember to start all hardware by hand before you tighten
anything.

10. Center the goal P12 over the opening in the end panel and attach using
screws H7 as shown in FIGURE 4. Repeat for both ends of the table.

Figure 4

DETAIL

THIS STEP REQUIRES TWO OR MORE ADULTS.

VERY CAREFULLY TURN THE TABLE OVER AND SET IT ON

ITS LEGS. BE CAREFUL, THE TABLE IS VERY HEAVY

AND THE RODS WILL SLIDE. DO NOT LIFT THE TABLE BY

HOLDING ONTO THE RODS.

© 2003 Escalade Sports

9

For Customer Service Call 1-866-556-2759