Escalade sports G01606 User Manual

We strive to ensure that our products are of the highest quality

and free of manufacturing defects or missing parts. However, if

you have any problems with your new product,

DO NOT RETURN IT TO THE STORE,

please contact us toll free @:

1-866-556-2759

FAX: 1-866-873-3531

foosball@escaladesports.com

Or write to:

Escalade Sports

Customer Service Department

P.O. Box 889

Evansville IN 47706

Please have your model number when inquiring about parts.

When contacting Escalade Sports please provide your model number , serial number (if applicable), and part number if requesting a replacement part. These numbers are located on the product, packaging, and in this owners manual.

Y our Model Number _______________________

G01606

For Customer Service Call 1-866-556-2759

MPORTANT! READ THIS MANUAL ALL THE WAY THROUGH BEFORE BEGINNING TO PUT YOUR GAME TABLE TOGETHER! THEN READ EACH STEP BEFORE STARTING THAT STEP.

TWO ADULTS ARE REQUIRED TO ASSEMBLE

THIS GAME TABLE

Tools Required:

Allen Wrench H13 Included with the Hardware Kit Philips Screwdriver Furniture Polish and Cloth

An electric screwdriver is helpful in assembly. However, please set at low torque and use extreme caution with an electric screwdriver because you could overtighten the hardware and strip the screws.

Assembly Tips

Make sure you understand the following tips before you begin to assemble your soccer table.

1. When installing parts that have more than one bolt, start ALL the bolts in that part by hand before tightening anything.

2. Some drawings or images in this manual may not look exactly like your product. Please read and understand the text before starting each assembly step.

READ AND FOLLOW ALL ASSEMBLY, OPERA TION, AND

SAFETY INSTRUCTIONS CAREFULLY . AT LEAST TWO

ADULTS ARE NEEDED TO PUT THIS GAME TABLE

TOGETHER.

For Customer Service Call 1-866-556-2759

1. Find a clean, level place to begin the assembly of your soccer table. We recommend building the table on the box top to protect the parts during assembly.

2. Attach the end panel top P3 to the end panel base P2 using screws H1 as shown in FIGURE 1. Repeat this step for both end panels.

Figure 1

3. Work up side down with the ball entry hole closest to the floor and the end panel tops on the floor . Use the Allen W rench provided H13 and attach the previously made assemblies to one side panel P1 using bolts H2, washers H3, and barrel nuts H4 as shown in FIGURE 2. Use a screwdriver to align the barrel nuts. Remember to start all hardware by hand and do not tighten at this time.

CAUTION:

DO NOT TIGHTEN

HARDWARE AT

Figure 2

For Customer Service Call 1-866-556-2759

4. Align the rods as shown in FIGURE 3. Please note the location of the hole that is near one end of each rod. This is the handle end of the rod. There will be four handles on each side of the table. It is critical that you set the rods as shown below so the table will be correct when flipped over .

Figure 3

CAUTION:

Set the rods as shown noting the location of the hole / handle end.

5. Slide the playfield P4 into the cabinet assembly as shown in FIGURE 4.

Figure 4

For Customer Service Call 1-866-556-2759

6. Using the Allen Wrench provided H13, attach the other side panel to the cabinet assembly using screws H2, washers H3 and barrel nuts H4 as shown in FIGURE 5. Again leave the hardware hand tight.

7. Place the playfield support braces P5 on the bottom of the playfield as shown. Slide the cabinet rods H6 through the side panels and down the groove in the support braces. Secure with locknut H7 and washer H3 as shown in FIGURE 5.

8. Tighten all hardware at this time.

9. Secure the playfield with screws H5. Use caution not to overtighten these screws.

Figure 5

For Customer Service Call 1-866-556-2759

+ 19 hidden pages

Escalade sports G01606 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual