Escalade sports B9706 User Manual
OWNER'SOWNER'S
OWNER'S
OWNER'SOWNER'S
MANUMANU
MANU
MANUMANU
ALAL
AL
ALAL
WARNING
FAILURE TO FOLLOW THESE
WARNINGS MAY RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
Owner must ensure that all
players know and follow these
rules for safe operation of the
! Do not dunk on this unit
! Do not hang from any part of the unit,
including the backboard, rim, or net.
! Do not slide, climb, or play on pole.
! Keep organic material away from
pole base. Grass, litter, etc. could
cause corrosion and /or deterioration.
! Check pole system twice a year for
signs of corrosion (rust, pitting,
chipping). Remove rust and/or loose
paint completely and repaint with
exterior enamel paint. If rust has
penetrated through the steel
anywhere, replace pole immediately.
! Check unit before each use for loose
hardware, excessive wear, and signs
of corrosion and repair before using.
! During play, use extreme caution to
keep players face away from the
backboard, rim, and net.
! Wear a mouthguard when playing to
avoid dental injuries.
! When adjusting height, keep hands
and fingers away from moving parts.
! During play, do not wear jewelry
(rings, watches, necklaces, etc.).
Objects may entangle in net.
unit.
ADJUSTABLE BASKETBALL POLEADJUSTABLE BASKETBALL POLE
ADJUSTABLE BASKETBALL POLE
ADJUSTABLE BASKETBALL POLEADJUSTABLE BASKETBALL POLE
WITHWITH
WITH
WITHWITH
PROPRO
“
PRO
PROPRO
STYLESTYLE
STYLE”
STYLESTYLE
BREAKAWAY
MODEL NUMBER
B9706
Thank you for buying our basketball pole. We try hard to ensure that our products are of high quality and
free of manufacturing defects and of missing parts. However, if you have any problems with your
basketball pole, such as a manufacturing defect or a missing part, please DO NOT RETURN IT TO THE
STORE. Call us at:
TOLL FREE 1-800-426-1421
(THIS IS A CONSUMER ONLY NUMBER)
FAX: (812) 467-1399
Or write us at:
CUSTOMER SERVICE DEPT., P.O. Box 889, Evansville, IN 47706
Please provide model number, serial number, and/or part number of the product and/or part when you call or
write. These numbers can be found on the product, packaging, or in this owner's manual.
To make assembly of your basketball pole
easier, use the Hardware Identifier on page
2 to identify and sort all fasteners.
Do not tighten hardware until instructed to do so. If
hardware is tightened too soon, mounting holes may not
align and parts may not fit together. Leave locknuts
slightly loose until you are instructed to tighten them.
Read this manual all the way through before
starting to put up your pole. Then read each
step completely before beginning that step.
Some smaller parts may be
shipped inside larger tubes.
Check inside tubes before
assembling or ordering parts.
IMPORTANT! Use the illustration below to identify
the correct pole sections. Once sections are
seated together, you will NOT be able to pull
them apart!
1
2L-6543-00
To put up your pole, you will need the following tools:
" Post Hole Digger " Shovel " Level " Ladder " Tape Measure " Phillips and Flat Blade Screwdrivers
" Hammer " Gravel " Two adjustable wrenches OR two 1/2" Wrenches and One 9/16" Wrench
" Besides these tools, you will need approximately 1.6 cubic feet (three 80 lb. bags) of concrete to set your pole in the ground.
2
ASSEMBLY INSTRUCTIONS:
1. Before putting any of the pole tubes together, mark the
two lower pole sections (#2) 4¼ inches from their top
(tapered) end. (See Figure 1)
2. Insert one lower pole section (#2) into the flanged
end of the other lower pole section (#2) snugly.
Pound the poles on a piece of wood to secure. Hit
the poles until there is no more movement or until
the bottom end of the upper and middle poles
reaches the 4¼ inch mark on the middle and lower
poles respectively. Hit tubes a minimum of seven
times. This is a friction-locking joint and requires no
hardware. NOTE: You may have to turn poles
upside down and pound top to completly seat.
Figure 1
Insert the lower pole section (#2) into the flanged
end of the upper pole section (#3) snugly. Seat
together as done for lower pole sections (#2).
Figure 2
4. Next, attach the clamp assembly to the pole as follows:
wrap slider shim (#28) around middle pole section (space
in shim must face rear of the pole). Then attach both clamp
halves to pole around shim by inserting bolt (#29) through
one clamp half (#27), through the pull tube (#19) (flat part
of pull tube faces pole. See Figure 3), through the other
clamp half, spacer (#26), washer (#8), and knob (#24).
Tighten knob until the clamp halves seat together
securely. See Figure 3.
3. Now measure down from middle hole in top pole
102 inches, and make a mark on bottom pole. You
will use this measurement later. See figure 2.
3
Figure 3
Loading...