Ericsson 19A705860P1, 19A705860P2, 19A705870P1, 19A705870P2 Maintenance Manual

Page 1
Printed in U.S.A.
MAINTENANCE MANUAL
CELLULAR HANDSETS
19A705860P1 & P2 (Basic)
19A705870P1 & P2 (Extended Features)
TABLE OF CONTENTS
Page
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
TEST SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
OUTLINE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
IC DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SPECIFICATIONS
POWER SUPPLY
Nominal 12.5 Vdc Range 10 to 16 Vdc
No failure or lack of function within this range.
CURRENT DRAIN (CU Power)
On Hook, No Audio Less than 25 mA Rated Audio 100 mA
OPERATING TEMPERATURE RANGE
Nominal 24°C Operating Range -30°C to +60°C
VCC VOL TA GE
At 25°C 5.0 Vdc to 5.4 Vdc, typical At 30°C 5.5 Vdc to 5.9 Vdc, typical At 70°C 5.0 Vdc to 4.6 Vdc, typical
ERICSSONZM
Ericsson GE Mobile Communications Inc.
Mountain View Road Lynchburg Virginia 24502
LBI-38412A
Page 2
DESCRIPTION
The handsets, shown in Figure 1, consists of a single printed
circuit board containing the following:
Numerical and function keypad
Liquid Crystal Display
All audio and logic circuitry
The printed circuit board conta ins t he micr ophone pream pli­fier, earpiece amplifier, speaker amplifier, keypad switches, a microcomputer and LCD driver, receive and transmit data buff­ers, a 5 volt regulator and backlight LED’s and circuitry.
Although the Basic (19A705860P1) and Extended (19A705870P1) models of the handset differ in external appear­ance, they are the same electronically. The Extended model has one extra key "
A-Z
" and indicators for
"HORN", "LOCK"
and
"MUTE"
.
Audio from the electret microphone (B1) is amplified by U1-A and passed to the transmit audio path of the radio.
Four bit microcomputer U5 (MB88543) scans the keypad and controls the LCD. The microcomputer also controls the LED backlighting of the display and keypad. When a key is pressed on the keypad, an ASCII code is generated by the microcomputer and serially transmitted to the mobile. The key release and a hookswitch change also send ASCII codes to the mobile. At power-up the handset sends a code to identify itself. The handset receives commands from the mobile to control the display (indi­cators, alpha and numeric characters) control the call timer , turn backlight on or off and interrogates status of han dset or hook­switch.
TEST SPECIFICATIONS
MICROPHONE
1.
Sensitivity
- An input level of 97 dB SPL produces
an output of 150 mV rms ± 5 dB. [
dB SP
L =
20
LOG 10 (P/Po
): P is the rms sound pressure in
Pascals and Po =
2 X 10
-5
Pascal]
2.
Distortion
- For an input signal of less than 1% distortion, the output distortion does not exceed 3% from 300 Hz to 3000 Hz.
RECEIVER
1.
Off Hook Sensitivity
- A one (1) kHz, 100 mV rms input signal produces an output of 94 ± 3 dB SPL, measured at the artificial ear.
2.
Distortion
- For an input signal of 100 mV rms with less than 1% distortion, the output distortion is less than 5% as measured at the artificial ear from 300 Hz to 3000 Hz.
3.
Ear Protection
- An audio limiter is provided to ensure that the maximum acoustic output does not exceed 120 dB SPL.
4.
On Hook Sensitivity
- A 1 kHz tone, 100 mV rms input signal produces an output of 80 ± 6 dB SPL as measured in the free field.
SIDETONE LEVEL
The acoustic to acoustic sidetone response is such that a 1000 Hz, 97 dB SPL transmit audio input signal produces 85 ± 6 dB SPL at the artificial ear.
ON/OFF
There is a momentary switch in the handset that is sensed in the mobile to control the 12 V supply to the handset.
SERIAL DATA
The serial data format is a pseudo RS-232 format. Specifi­cally, it is an asynchronous serial bus operating between Vcc and 0 volts.
Baud Rate
300 ±5%
Bit Pattern
One (1) start two (2) stop, eight (8) data and no parity .
Format
0 to Vcc inverted with Vcc being a no data condition.
Vcc
4.5 to 6.0 Vdc
Keypad Data
High-Open Collector drive less than 50 mA current drain.
Display Data
High Open Collector drive less than 50
mA current drain
Low 0.8 V maximum
Copyright © January 1991, Ericsson GE Mobile Communications Inc.
Figure 1 - Basic (19A705860P1) And E xtended (19A705870P1) Handsets
LBI-38412
1
Page 3
HANDSET TEST
HANDSET
To test the handset by itself, loop the keypad serial line to the Display serial line by connecting P1-1 to P1-3 on a test connector (refer to Figure 2). Apply nominal +12V to P1-5 and ground P1-2. Attach the connector on the handset cord to the test connector and turn the power on.
HANDSET SELFTEST
The handset test consists of tests of:
RAM
, display, back­light, call timer, keypad, hookswitch and serial communica­tions.
The test sequence is as follows:
Step Procedure Display
1. Power Up With
SELFTEST
Loopback connected.
2. After 1.6 seconds
RAM RAM PASS
or
test is complete
RAM FAIL
3. Start display test Step All segments through Display and common 0
After 1.6 seconds All segments
and common 2
After 1.6 seconds All segments
and common 3
After 1.6 seconds All segments
and common 1
After 1.6 seconds segments 2, 6, 10,
14, 18, 22, 26, 30 and all commons
After 1.6 seconds segments 0, 4, 8,
12, 16, 20, 24, 28 and all commons
After 1.6 seconds segments 3, 7, 11,
15, 19, 23, 27, 31 and all commons
After 1.6 seconds segments 1, 5, 9,
13, 17, 21, 25, 29 and all commons
4. Backlight T es t BACKLITE
After 1.6 seconds LITE ON
After 1.6 seconds LITE OFF
5. Call Timer Runn i ng 000 00 0 Any key, e x cept
END
,
will stop the
CALL
TIMER
and go to the
keypad test.
6. Keypad Test (Audio can be tested here) Any key can be pushed in any order:
Push 1 KEY 1
Push 2 KEY 2
..... ....
Push 0 KEY 0
Push END End key pad test
Push CLR KEY CLR
Push SND KEY SND
Push STO KEY STO
Push FCN KEY FCN
Push RCL KEY RCL
Push A-Z KEY ALP
Push VOL + KEY VUP
Push VOL - KEY VDN
On Hook to Off Hook OFF HOOK
Off Hook to On Hook ON HOOK
The
END
key ends the
Keypad tes t
7.
RAM
status (70=pass, 71=fail) is sent on the key pad serial line
8. Serial communications test (Audio can be tested here)
Serial communication is tested by pushing keys and displaying as follows:
With entries scrolling across the display, as many keys as needed can be pushed (F is key release)
F KEY: 0 F0F 1F0F1F 2 F0F1F2F 3 0F1F2F3F 4 1F2F3F4F 5 2F3F4F5F 6 3F4F5F6F 7 4F5F6F7F 8 5F6F7F8F 9 6F7F8F9F VOL - 7F8F9FAF VOL +
ROAM
Indicator Flash STORE 8F9FAFCF SEND 9FAFCF-F * AFCF-FHF # CF-FHF?F A-Z -FHF?F*F FCN HF?F*FAF A ?F*FAFBF B *FAFBFCF C AFBFCFDF PTT BFCFDFEF PTT Released CFDFEFGF On Hook FDFEFGFH Off Hook DFEFGFHI RCL FEFGFHI F END EFGFHI FF CLR FGFHI FFF
9. To complete the test, power down and remove the Loopback.
Figure 2 - Test Connection
LBI-38412
2
Page 4
OUTLINE DIAGRAM
IC DATA
BACK SI DEKEYPAD SIDE
(BP0303645D, Sheet 5) (BP0303645D, Sheet 1)
(BP0303645, Sheet 6) (BP0303645, Sheet 2)
OPERATIONAL AMPLIFIER U1 A29/UL0303551A0145 (MC4558)
AUDIO POWER AMPLIFIER U2 A29/UL0303548A0149 (LM386)
VOLTAGE REGULATOR U3 A29/UL3031586A0149 (LM317)
MICROCOMPUTER U5 A29/UL0303551A0145 (MB88543)
HEX INVERTERS U4 A29/UC0303549A0145 (74HC04)
LBI-38412
3
Page 5
SCHEMATIC DIAGRAM
(DX0303651, Sh. 1, Rev. B)
LBI-38412
4
Page 6
PART S LIST
LBI-38412
5
Loading...