Page 1
888-33-332-W-02 rev.G • 11/15
1 of 12
WorkFit-S, Dual
A 6 - 14 lbs (2.7-6.4 kg)
B 6 - 14 lbs (2.7-6.4 kg)
C < 5 lbs (2.3 kg)
A+B+C+D
< 25 lbs (11.3 kg)
D < 5 lbs (2.3 kg)
Includes
Constant Force™
Technology
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド:日本語
用户指南 : 汉语
ENGLISH
For the latest User Installation Guide please visit: www.ergotron.com
User's Guide
CAUTION: DO NOT EXCEED MAXIMUM LISTED
WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
Page 2
888-33-332-W-02 rev.G • 11/15
2 of 12
ENGLISH
These symbols alert users of a safety condition that demands attention. All users should
be able to recognize and understand the
signifi cance of the following Safety Hazards
if encountered on the product or within the
documentation. Children who are not able
to recognize and respond appropriately to
Safety Alerts should not use this product without adult supervision!
Hazard Symbols
Review
Symbol Signal Word Level of Hazard
NOTE
A NOTE indicates important information that helps you
make better use of this product.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
WARNING
A WARNING indicates either potential for property damage, personal injury, or death.
ELECTRICAL
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury, re
and/or death.
Safety
Important! You will need to adjust this product after installation is complete. Make sure all your equipment
is properly installed on the product before attempting adjustments. This product should move smoothly
and easily through the full range of motion and stay where you set it. If movements are too easy or
diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create
smooth and easy movements. Depending on your product and the adjustment, it may take many turns to
notice a difference. Any time equipment is added or removed from this product, resulting in a change in
the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum
operation.
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong
enough to handle mounted product and equipment.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow
these instructions may result in equipment damage or personal injury.
CAUTION! Tipping Hazard. Support the stand until the clamp is securely tightened. Failure to follow these
instructions may result in the stand tipping over causing possible equipment damages and or personal injury.
Page 3
888-33-332-W-02 rev.G • 11/15
3 of 12
1
2
4
12
11
ENGLISH
GREEN ARROWS MARK IMPORTANT ADJUSTMENT POINTS
After installation, adjust product to properly handle added weight.
To view a video on this adjustment procedure, go to
install.ergotron.com
Important! You will need to adjust this product after installation is complete. Make sure all your equipment
is properly installed on the product before attempting adjustments. This product should move smoothly
and easily through the full range of motion and stay where you set it. If movements are too easy or
diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create
smooth and easy movements. Depending on your product and the adjustment, it may take many turns to
notice a difference. Any time equipment is added or removed from this product, resulting in a change in
the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum
operation.
Follow Steps 1 - 8 for Installation
Page 4
888-33-332-W-02 rev.G • 11/15
4 of 12
AB
1
2
3
4
5
6
7
8
9
10
11
12
13
14mm
M4 x 10mm
M4 x 8mm
M4 x 10mm
8x
12x
4x
3x
2x
2x
M4 x 5mm
3x
M6 x 6mm
1x
1x
2x
1x
1x
3x
M5 x 14mm
7.5˚
18"
(45.7 cm)
1x
2x
1x
4mm
3mm
2x
1x
1x
4x
1x
1x
M4x12mm
2x
M5 x 12mm
1x
4.8"
(122 mm)
68˚
ENGLISH
Components
Tools Needed
Features & Specifi cations
Page 5
888-33-332-W-02 rev.G • 11/15
5 of 12
0.47" - 1.38" (12 - 35 mm) 1.46" - 2.4" (37 - 60 mm)
4mm
1
123
ENGLISH
Page 6
888-33-332-W-02 rev.G • 11/15
6 of 12
2
4mm
4x
M6 x 6mm
3x
M5 x 14mm
3mm
3
ab
ENGLISH
CAUTION! Tipping Hazard. Support the stand
until the clamp is securely tightened. Failure
to follow these instructions may result in
the stand tipping over causing possible
equipment damages and or personal injury.
Page 7
888-33-332-W-02 rev.G • 11/15
7 of 12
2x
M5 x 12mm
5
4
2x
1x
a b c
ENGLISH
Page 8
888-33-332-W-02 rev.G • 11/15
8 of 12
7
8
M4 x 10mm
M4 x 10mm
4x
4x
3.5˚
8.5˚
6
0°
M4 x 8mm
2x
b
4x
4x
M4x10mm
M4x12mm
a
ENGLISH
Page 9
888-33-332-W-02 rev.G • 11/15
9 of 12
9
10
2x
1x
M4 x 5mm
M4 x 5mm
1x
3x
2x
1x
2x
ENGLISH
Center total width of mounted equipment on stand.
Page 10
888-33-332-W-02 rev.G • 11/15
10 of 12
A
14mm
WARNING
A primary mechanism within the
tower is under tension and can
be hazardous to people
exposed to it under certain
extreme conditions. DO NOT
open the tower; DO NOT attempt
to service the cart/stand. DO NOT
remove safety guards or labels
designed to protect or inform of
possible hazards. Only
Ergotron-approved installers may
service or otherwise modify
cart/stand. Failure to heed this
Warning may result in serious
Personal Injury and Damage both
to the cart/stand and equipment.
STORED ENERGY HAZARD!
DO NOT OPEN TOWER OR REMOVE
SAFETY GUARD!
822-959-00
11
ENGLISH
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
Adjustment may take up to: 72 full 360° revolutions
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
Page 11
888-33-332-W-02 rev.G • 11/15
11 of 12
B
C
4mm
12
a
b
4x
M5 x 8mm
ENGLISH
Adjustment may take up to: 115 full 360° revolutions
How to attach optional CPU holder ordered separately
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
Page 12
888-33-332-W-02 rev.G • 11/15
12 of 12
© 2015 Ergotron, Inc. All rights reserved.
ENGLISH
Learn more about ergonomic computer use at:
www.computingcomfort.org
Set Your Workstation to Work For YOU!
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists fl at.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain fl at.
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
Loading...