Ergotron WorkFit-P User Manual
1 of 8
888-45-300-G-00 rev. C • 11/13
Reduce.Reuse.Recycle
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Nederlands
Benutzerhandbuch - Deutsch
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド : 日本語
用户指南 : 汉语
www.ergotron.com
5-15 lbs
(2.27-6.8 kg)
Important!
You will need to adjust this product after installation is complete.
Make sure all your equipment is properly installed on the
product before attempting adjustments. This product should
move smoothly and easily through the full range of motion and
stay where you set it. If movements are too easy or di cult or if
product does not stay in desired positions, follow the adjustment
instructions to create smooth and easy movements. Depending
on your product and the adjustment, it may take many turns to
notice a di erence. Any time equipment is added or removed from
this product, resulting in a change in the weight of the mounted
load, you should repeat these adjustment steps to ensure safe and
optimum operation.
0.78"-2.56" (20-65mm)
0.5"-2.5"
(13-64mm)
WorkFit-P
ENGLISH
CAUTION: DO NOT EXCEED MAXIMUM LISTED
WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
2 of 8
888-45-300-G-00 rev. C • 11/13
WARNING
ENGLISH
Warning! Stored Energy Hazard: The arm mechanism is under tension
and will move up rapidly, on its own, as soon as attached equipment is
removed. For this reason, DO NOT remove equipment unless the arm has
been moved to the highest position! Failure to follow this instruction may
result in serious personal injury and/or equipment damage!
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure
mounting surface is strong enough to handle mounted product and equipment.
These symbols alert users of a safety condition that
demands attention. All users should be able to
recognize and understand the signi cance of the following Safety Hazards if encountered on the product
or within the documentation. Children who are not
able to recognize and respond appropriately to Safety
Alerts should not use this product without adult
supervision!
Hazard Symbols Review
Safety
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly
installed on the product before attempting adjustments. This product should move smoothly and easily through the full
range of motion and stay where you set it. If movements are too easy or di cult or if product does not stay in desired
positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the
adjustment, it may take many turns to notice a di erence. Any time equipment is added or removed from this product,
resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and
optimum operation.
Symbol Signal Word Level of Hazard
NOTE
A NOTE indicates important information that helps you
make better use of this product.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
WARNING
A WARNING indicates either potential for property damage, personal injury, or death.
ELECTRICAL
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury, re
and/or death.
3 of 8
888-45-300-G-00 rev. C • 11/13
ABC D E
1
2
3
4
5
6
1x
1x
1x
1x
1x
1x
2x
4x
4x
1x
1x
5mm
8mm
13mm
M4 x 14mm
M4 x 8mm
4 mm
2.5 mm
1x
1x
1x
2x
20”
360˚
180˚
1x
1x 1x
ENGLISH
Components
Tools Needed
Features
Loading...