Built with Anthro-DNA™
User's Guide
The Peanut
Product Part#
The Peanut PT1GMPW3
The Peanut for Tablets PT2GMPW3
NOTE: The Peanut, Tall, is shown. The tablet and keyboard are not included.
For the latest User Installation Guide please visit: www.ergotron.com
300-5611-00 rev. B • 06/16
1 of 2
01
02
03
05
06
TOOLS
The Peanut comes with these tools:
• 3-way wrench
Not provided, but suggested:
• 7/16" nut driver
• 3/8" nut driver
04
07
08
For Peanut for Tablets:
10
09
PARTS LIST
Before beginning assembly of The Peanut, please review
the parts list to verify that your shipment is complete.
Product Quantity Part Number
01 Shelf 1
for The Peanut 225-4834-00
for The Peanut for Tablets 225-4837-00
02 Handle (installed on shelf) 1 125-5411-00
03 Column Assembly 1
for The Peanut 500-1108-00
for The Peanut for Tablets 500-1109-00
04 Cable Sleeve 1 280-5056-00
05 Base 1 225-4833-00
06 Casters, Non-locking 2 150-5117-00
07 Casters, Locking 2 150-5118-00
08 1/4-20 Nylock Nut 24 325-5259-00
09 VESA Tilt Assembly 1 835-5639-00
for Peanut for Tablets
10 Easel Assembly 1 835-5640-00
for Peanut for Tablets
11 #10-24 x 0.75" Flat Head Screw 2 325-5270-00
for Peanut for Tablets (not shown)
2 of 4
300-5611-00 rev. B • 06/16
STEP 1 - ATTACH THE CASTERS TO THE BASE
Lay the base upside down on work surface or oor.
Align the mounting holes in each caster plate with the bolts sticking
out of the base. Locking casters (with tabs as shown) attach to the
longer base legs.
Attach each caster with four nylock nuts using a 7/16" nut driver.
1/4-20 Nylock Nuts
325-5259-00
STEP 2 - ATTACH BASE TO THE COLUMN
Align mounting holes in base with bolts
sticking out of the bottom of the
column.
Attach the base with four nylock nuts
using a 7/16" nut driver.
1/4-20 Nylock Nuts
325-5259-00
Locking Casters
STEP 3 - ATTACH SHELF TO COLUMN AND CABLE SLEEVE
Stand the column up on its casters.
Align mounting holes on column with
bolts in shelf so the handle is over the
locking casters.
Attach the shelf with four nylock nuts
using a 7/16" nut driver.
Slip the Cable Sleeve over the tube and
press into place.
1/4-20 Nylock Nuts
325-5259-00
STEP 4 - ATTACH VESA MOUNT TO COLUMN
Rotate VESA plate on mounting assembly so it can lay at.
Align mounting holes in mounting assembly with holes in top of
column.
Attach VESA mounting assembly with two hex bolts using 1/8" hex key.
#10-24 x 0.75” Flat-hd Screw
325-5270-00
300-5611-00 rev. B • 06/16
3 of 2
STEP 5A - ATTACH DEVICE HOLDER TO VESA PLATE
Align device holder with the VESA plate so the four threaded studs on
the holder line up with four holes on the plate.
Attach the device holder to the plate with four acorn nuts using your
3/8" driver.
To adjust the device holder, loosen the adjustment knobs at the back of
the device holder, slide the top of the holder into position, then tighten
the knobs.
3/8” Acorn Nut
325-5023-00
STEP 5B - ATTACH TABLET CASE TO VESA PLATE
Align the holes in the back of your tablet case with the four outer holes
in the VESA mount.
Attach monitor with mounting screws that come with the case.
CONGRATULATIONS! YOUR CART ASSEMBLY IS COMPLETE!
For Warranty visit: www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
© 2016 Ergotron, Inc. All rights reserved.
All trademarks are the property of their respective companies. Anthro is a registered trademark and brand of Ergotron Inc.
Anthro-DNA is a trademark of Ergotron Inc.
4 of 4
300-5611-00 rev. B • 06/16
Loading...