Page 1
User's Guide
StyleView Sit Stand Combo System
with Small CPU Holder
For the latest User Installation Guide please visit: www.ergotron.com
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
www.ergotron.com |
888-45-207-W-02 rev. K • 01/19
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
|
China: 400-120-3051
|
English
Japan: japansupport@ergotron.com
1 of 23
Page 2
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly
installed on the product before attempting adjustments. This product should move smoothly and easily through the
full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in
desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your
product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed
from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps
to ensure safe and optimum operation.
1.38" - 3.75"
(35-95 mm)
< 50 lbs (22.7 kg)
20"
(508mm)
5"
(127mm)
25˚
5˚
6-18 lbs*
(2.7-8.2 kg)
1-4 lbs
(0.45-1.8 kg)
360˚
180˚
* The Combo Arm can be modi ed to mount displays up to 25 lbs (11.3
kg), however display lift and tilt motion will not be possible if this option
is chosen. Refer to special instructions on page 14.
Tools Needed
1/4”
Stud Finder
2 of 23
2
1
Ø 7/32" (5.6 mm)
Ø 3/8" (10 mm)
Concrete Wall Mounting
90˚
10mm
11 mm
13 mm
7/16"
Ø 1/2" (12.8 mm)
HOLLOW WALL
-10˚
11mm
1/4"
> 3"
888-45-207-W-02 rev. K • 01/19
Page 3
Components
AB C D E
1x
1
2x
2x
2x
1x
1x
2x
3x
1x
2
1x
1x
1x
3
M8 x 16mm
1x
4x
1x
5x
7x
2x
2x
1x
1x
1x
1x
8x
8x
4
1x
8mm
1x
5
6
7
8
9
4x
2x
M5 x 15mm
1x
1x
1x
M4 x 8mm
10x
M6 x 70mm
10x
1/4-20 x 2"
10x
4x
M4 x 10mm
Flat Head Pan Head
2x
M4 x 6mm
4x
M4 x 10mm
Optional Weight Capacity Modi cation Fasteners
4x
M4.2 x 25mm
10x
6 mm
1x
4x
1x
M3.5 x 8mm
1x
3 mm
M10 x 18mm
4x
10x
M6
2x
M6 x 10mm
2x
M10 x 16mm
888-45-207-W-02 rev. K • 01/19
3 of 23
Page 4
Mounting Height for Ergonomic Workstation
1
This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5’3”-5’9” (160175cm).
If user heights are di erent than this, you should change mounting height to accommodate user heights. (Change mounting
height one inch for every one inch di erence in user heights).
Mounting height assumes there is a 6” (152 mm)
distance between the center of your monitor
mounting holes and the top of the screen. If your
distance is smaller, you should increase mounting
height accordingly, if your distance is larger, you
should decrease your mounting height accordingly.
< 31.5”
(800mm)
32.5”
(826mm)
21”
(533 mm)
6”
(152 mm)
5’3”-5’9”
(160-175cm)
Determine mounting location:
Front view with arm pushed back against the wall.
(712mm)
(478mm)
8.1”
(206mm)
8.9”
(226mm)
9.4”
12.3”
(311mm)
16.8”
(425mm)
(238mm)
Top view showing range of motion when pulled out from the wall.
28”
18.8”
4 of 23
888-45-207-W-02 rev. K • 01/19
Page 5
2
Concrete Wall Mounting
10x
10x
10x
M6
Ø 3/8" (10 mm)
6
10x
10x
Studs ≥ 25
gauge steel
Sheetrock
≥ 5/8"
Stud spacing
≤ 16"
Ø 1/2"
1/4-20 x 2"
8
WARNING: Because surfaces vary widely and the ultimate mounting method is out of Ergotron’s control, it is imperative that you consult with
appropriate engineering, architectural or construction professional to ensure that your Ergotron mounting solution is mounted properly to handle applied loads.
888-45-207-W-02 rev. K • 01/19
5 of 23
Page 6
2
Concrete Wall Mounting
WARNING:
Mounting holes must be at least 3-1/8” (80mm) deep and must be located within solid
concrete, not mortar or covering material. If you drill into an area of concrete that is
not solid, reposition mounting holes until both anchors can be fully inserted into solid
concrete!
a
b
x 10
c
3-1/8"
(80 mm)
x 10
WARNING:
Anchors that are not fully set in solid concrete will not support the applied load
resulting in an unstable, unsafe condition which could lead to personal injury
and/or property damage. Consult a construction professional if you have any
doubt about what this means in regard to your particular situation.
6 of 23
888-45-207-W-02 rev. K • 01/19
Page 7
d
10x
123
e
10x
M6
10x
M6 x 70mm
10mm
10mm
CAUTION: Make sure the wall mount bracket is level,
ush and snug to the wall surface. DO NOT OVERTIGHT-
EN THE BOLTS.
888-45-207-W-02 rev. K • 01/19
3
10
7 of 23
Page 8
2
HOLLOW WALL
Studs ≥ 25
gauge steel
Sheetrock
≥ 5/8"
Stud spacing
acb
Requires minimum material thickness of 5/8” (16 mm).
≤ 16"
10x
8 of 23
888-45-207-W-02 rev. K • 01/19
Page 9
HOLLOW WALL
2
d
10x
e
10x
1
1/4-20 x 2"
2
34
CAUTION: Make sure the wall mount bracket is level,
ush and snug to the wall surface. DO NOT OVERTIGHT-
EN THE BOLTS.
888-45-207-W-02 rev. K • 01/19
3
10
9 of 23
Page 10
3
a
4x
b
M10 x 18mm
M6 x 10mm
c
3 mm
d
¼"
6 mm
NOTE: Fasteners may unwind due to vibration caused by movement of mounting solution over time. Inspect mounting solution
for loose fasteners on a routine basis. If desired, apply a light duty
thread locking adhesive to fasteners before installation to prevent
back-out.
10 of 23
888-45-207-W-02 rev. K • 01/19
Page 11
4
a
bc d
2x
M10 x 16mm
M6 x 10mm
3 mm
e f
12x
6 mm
g
i
2x
h
888-45-207-W-02 rev. K • 01/19
11 of 23
Page 12
5
1x
M8 x 16mm
1x
1x
1x
1x
13 mm
6
2x
M5 x 15mm
3 mm
12 of 23
888-45-207-W-02 rev. K • 01/19
Page 13
7
a
b
f
g
c
4x
d
h
i
e
888-45-207-W-02 rev. K • 01/19
13 of 23
Page 14
Optional Weight Capacity Modi cation
Optional Weight Capacity Modi cation for Displays 18 - 25 lbs (8.2 - 11.3 kg) Only!
IMPORTANT: with this option display lift and tilt motion are no longer possible. To accomodate extra weight, the display is xed at one of three heights (spaced
2.5" (64 mm) apart), and display tilt is xed at 20°. If mounting a display 18 lbs (8.2 kg) or less, skip to next page.
i
ii
a
a c
b
1x
M4 x 8mm
b
Flat Head
1x
2x
M4 x 6mm
Pan Head
1x
20˚
14 of 23
888-45-207-W-02 rev. K • 01/19
Page 15
8
0˚
1x
M3.5 x 8mm
75mm
4x
M4 x 10mm
9
100mm
4x
888-45-207-W-02 rev. K • 01/19
15 of 23
Page 16
10
NOTE: Leave enough slack in cable to allow full range of motion.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to
follow these instructions may result in equipment damage or personal injury.
bca
edf
g
h
ij
16 of 23
888-45-207-W-02 rev. K • 01/19
Page 17
k
NOTE: Make sure cables can slide in and out through
covers and cable channels.
l
m
2x
7x
5x
11
12
888-45-207-W-02 rev. K • 01/19
2x
12
17 of 23
Page 18
13
a
2x
4x
4x
M4.2 x 25mm
2x 2x
Ø 7/32" (xx mm)
.21875
2x
CAUTION: Make sure there is enough clearance between back of mounted component and cable
channel. Failure to allow clearance space may result in personal injury and equipment damage.
b
2x
2x 2x
cd
12 3
Flush with drywal
1x 1x
M4.2 x 25mm M4.2 x 25mm
f
ghe
2x
18 of 23
888-45-207-W-02 rev. K • 01/19
Page 19
ik
2x
14
ab
c
d
15
888-45-207-W-02 rev. K • 01/19
19 of 23
Page 20
16
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
Adjustment Step
a
Lift – Up and down
1/4”
8mm
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
20 of 23
888-45-207-W-02 rev. K • 01/19
Page 21
b
Lift – Up and down
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
11mm
> 3"
1/4"
lowered, then you'll need to decrease
Lift Strength:
c
Tilt – Forward and Backward
If this product moves too easily, then
you'll need to increase friction:
Decrease Friction
If this product is too diffi cult to move,
then you'll need to decrease friction:
Increase Friction
888-45-207-W-02 rev. K • 01/19
21 of 23
Page 22
d
Arm Swing – Side-to-side
Increase Friction
If this product moves too easily, then
you'll need to increase friction:
Decrease Friction
If this product is too diffi cult to move,
then you'll need to decrease friction:
13 mm
e
Keyboard Storage Keyboard Use Set Keyboard Angle to -10 degrees
90˚
-10˚
22 of 23
888-45-207-W-02 rev. K • 01/19
Page 23
f
3 mm
Set Your Workstation to Work For YOU!
Learn more about ergonomic computer use at:
www.computingcomfort.org
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists at.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain at.
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
www.ergotron.com |
© 2014 Ergotron, Inc. All rights reserved.
888-45-207-W-02 rev. K • 01/19
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
|
China: 400-120-3051
|
Japan: japansupport@ergotron.com
23 of 23
Loading...