Ergotron 45-270-216 User Manual

2" - 8"

(102 - 203 mm)

User's Guide

StyleView Sit Stand Combo System, with

Worksurface and Medium CPU Holder

6-18 lbs*

(2.7-8.2 kg)

< 40 lbs (18 kg)

20"

(508mm)

1-4 lbs

(0.45-1.8 kg)

* The Combo Arm can be modi ed to mount displays up to 25 lbs (11.3 kg), however display lift and tilt motion will not be possible if

this option is chosen. Refer to special instructions on page 13.

25˚

360˚

5"

(127mm)

5˚

90˚

8"

(202mm)

180˚

ENGLISH

For the latest User Installation Guide please visit: www.ergotron.com

User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska

ユーザーガイド:日本語

用户指南 : 汉语

888-45-206-W-04 rev.N • 10/14

1 of 22

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly
installed on the product before attempting adjustments. This product should move smoothly and easily through the
full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in
desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your
product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed
from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps
to ensure safe and optimum operation.

Tools Needed

ENGLISH

10mm

2

1

1/4”

11 mm
13 mm
7/16"

Stud Finder

Ø 7/32" (5.6 mm)

Ø 3/8" (10 mm)

Concrete Wall Mounting

Ø 1/2" (12.8 mm)

HOLLOW WALL

2 of 22

888-45-206-W-04 rev.N • 10/14

Components

AB C D E

1x

1

2x

2x

2x

1x

1x

1x

2x

3x

1x

2x

2

1x

1x

1x

3

M8 x 16mm

1x

4x

1x

1x
1x

1x

1x

1x

4

1x

8mm

7x

7x

2x

4x

2x

ENGLISH

8x

8x

5

6

7

8

9

2x

M5 x 15mm

1x

1x

1x

2x

M4 x 10mm

10x

10x

4x

10x

M4 x 10mm

1x

M4 x 8mm

2x

M4 x 6mm

4x

M6 x 70mm

M4.2 x 25mm

10x

1/4-20 x 2"

6 mm

1x

4x

M4 x 10mm

Optional Weight Capacity Modi cation Fasteners

4x

1x

M3.5 x 8mm

1x

3 mm

M10 x 18mm

4x

10x

M6

2x

M6 x 10mm

2x

M10 x 16mm

888-45-206-W-04 rev.N • 10/14

3 of 22

Mounting Height for Ergonomic Workstation

1

This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5’3”-5’9” (160­175cm).

If user heights are di erent than this, you should change mounting height to accommodate user heights. (Change mounting
height one inch for every one inch di erence in user heights).

Mounting height assumes there is a 6” (152
mm) distance between the center of your
monitor mounting holes and the top of the
screen. If your distance is smaller, you should
increase mounting height accordingly, if your
distance is larger, you should decrease your
mounting height accordingly.

< 27.5”

(699mm)

28.5”

(724mm)

21”

(533 mm)

6”

(152 mm)

5’3”-5’9”

(160-175cm)

ENGLISH

Determine mounting location:

Front view with arm pushed back against the wall.

11.9”
(301mm)

9.2”

(232mm)

12.5”

(318mm)

17”

(430mm)

Top view showing range of motion when pulled out from the wall.

31.9”

(810mm)

22.7”

(575mm)

9.5”
(241mm)

4 of 22

888-45-206-W-04 rev.N • 10/14

2

Concrete Wall Mounting

10x

10x

10x

M6

Ø 3/8" (10 mm)

6

10x

10x

Studs ≥ 25

gauge steel

Sheetrock

≥ 5/8"

Stud spacing

≤ 16"

Ø 1/2"

1/4-20 x 2"

HOLLOW WALL

ENGLISH

8

WARNING: Because surfaces vary widely and the ultimate mounting method is out of Ergotron’s control, it is imperative that you consult with

appropriate engineering, architectural or construction professional to ensure that your Ergotron mounting solution is mounted properly to handle applied loads.

888-45-206-W-04 rev.N • 10/14

5 of 22

2

Concrete Wall Mounting

WARNING:

Mounting holes must be at least 3-1/8” (80mm) deep and must be located within solid

concrete, not mortar or covering material. If you drill into an area of concrete that is

not solid, reposition mounting holes until both anchors can be fully inserted into solid

concrete!

a

ENGLISH

b

x 10

c

3-1/8"
(80 mm)

x 10

WARNING:

Anchors that are not fully set in solid concrete will not support the applied load

resulting in an unstable, unsafe condition which could lead to personal injury

and/or property damage. Consult a construction professional if you have any

doubt about what this means in regard to your particular situation.

6 of 22

888-45-206-W-04 rev.N • 10/14

d

10x

123

e

10x

M6

10x

M6 x 70mm

10mm

ENGLISH

10mm

CAUTION: Make sure the wall mount bracket is level,

 ush and snug to the wall surface. DO NOT OVERTIGHT-

EN THE BOLTS.

888-45-206-W-04 rev.N • 10/14

3

10

7 of 22