Page 1
User's Guide
400 Series Flat Panel Monitor Arm
Rotate Mount Double Pivot P/L
< 23lbs. (10.44 kg)
www.ergotron.com |
888-45-031-01 rev. G • 09/19
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
|
China: 400-120-3051
|
Japan: japansupport@ergotron.com
1 of 10
Page 2
Hazard Symbols
Symbol Signal Word Level of Hazard
Review
These symbols alert users of a safety condition that demands attention. All users should
be able to recognize and understand the
signifi cance of the following Safety Hazards
if encountered on the product or within the
documentation. Children who are not able
to recognize and respond appropriately to
Safety Alerts should not use this product without adult supervision!
Safety
Important! You will need to adjust this product after installation is complete. Make sure all your
equipment is properly installed on the product before attempting adjustments. This product should
move smoothly and easily through the full range of motion and stay where you set it. If movements
are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment
instructions to create smooth and easy movements. Depending on your product and the adjustment,
it may take many turns to notice a diff erence. Any time equipment is added or removed from this
product, resulting in a change in the weight of the mounted load, you should repeat these adjustment
steps to ensure safe and optimum operation.
NOTE
CAUTION
WARNING
ELECTRICAL
A NOTE indicates important information that helps you
make better use of this product.
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
A WARNING indicates either potential for property damage, personal injury, or death.
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury, re
and/or death.
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong
enough to handle mounted product and equipment.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow
these instructions may result in equipment damage or personal injury.
2 of 10
888-45-031-01 rev. G • 09/19
Page 3
Components
AB CD
1
2
3
4
1x
1x
4x
#8-32
4x
M4 x 10mm
75-100mm
1x
3/32"
1x 4x 2x
1/8"
#10-24x3/8"
1x
4x 2x
3/16"
4x
M4 x 10mm
#6-32x1/2"
Mounting Height for Ergonomic Workstation
This mounting height is a recommendation for an ergonomic workstation that accommodates user
heights of 5’1” - 5'11". If user heights are di erent than this, you should change mounting height to
accommodate user heights. (Change mounting height one inch for every one inch di erence in user heights).
6”
(152 mm)
Mounting height assumes
there is a 6” (152 mm)
distance between the center
of your monitor mounting
holes and the top of
the screen. If your
distance is smaller, you
should increase mounting
height accordingly,
if your distance
is larger, you should
decrease your mounting
height accordingly.
44”
(1118mm)
5’1” - 5’11”
(156-180cm)
CAUTION: DO NOT EXCEED
MAXIMUM LISTED WEIGHT
CAPACITY. SERIOUS INJURY
OR PROPERTY DAMAGE MAY
OCCUR!
< 23lbs. (10.44 kg)
888-45-031-01 rev. G • 09/19
3 of 10
Page 4
1
Attach arm to wall.
a
THIS
SIDE
UP
4x
#10-24x3/8"
NOTE: Fasteners may unwind due to
vibration caused by movement of
mounting solution over time.
Inspect mounting solution for loose
fasteners on a routine basis. If desired,
apply a light duty thread locking adhesive to fasteners before installation to
prevent back-out.
b
cd
1/8"
4 of 10
888-45-031-01 rev. G • 09/19
Page 5
2
Attach monitor to arm.
75 mm x 75 mm
100 mm x 100 mm
a
4x
#8-32
4x
4x
3/32"
M4 x 10mm
b
M4 x 10mm
888-45-031-01 rev. G • 09/19
4x
M4 x 10mm
4x
M4 x 10mm
5 of 10
Page 6
3
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a diff erence. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
a
b
Double Pivot Arm
Mounted Weight Arm
lbs (kgs) Setting
<5 (<2.3) A
6-7 (2.7-3.2) B
8-9 (3.6-4.1) C
10-11 (4.5-5.0) D
12-14 (5.4-6.4) E
15-16 (6.8-7.3) F
17-18 (7.7-8.2) G
19-20 (8.6-9.1) H
21-22 (9.5-10.0) I
23 (10.4) J
-- -- K
NOTE: Continue with adjustmentstep b only if correct
arm counterbalance was not achieved in step a.
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
6 of 10
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
888-45-031-01 rev. G • 09/19
Page 7
4
a
5
a
b
1/2" (12.7mm)
1/2" (12.7mm)
Increase Friction
If this product moves too easily, then
you'll need to increase friction:
Decrease Friction
If this product is too diffi cult to move,
then you'll need to decrease friction:
b
1/2"
(12.7mm)
Increase Friction
If this product moves too easily, then
you'll need to increase friction:
Decrease Friction
If this product is too diffi cult to move,
then you'll need to decrease friction:
c
c
888-45-031-01 rev. G • 09/19
7 of 10
Page 8
5
b
a
Increase Friction
If this product moves too
easily, then you'll need to
increase friction:
Decrease Friction
If this product is too diffi cult
to move, then you'll need to
decrease friction:
c
6
b
1/2" (12.7mm)
a
1x
#6-32x1/2"
c
8 of 10
888-45-031-01 rev. G • 09/19
Page 9
7
NOTE: Leave enough slack in cable to allow full range of motion.
Caution: To avoid the potential to pinch cables it is important to follow the cable routing
instructions in this manual. Failure to follow these instructions may result in equipment
damage or personal injury.
bcda
efg
8
Attach covers.
How to remove covers.
a
a
b
b
c
c
888-45-031-01 rev. G • 09/19
9 of 10
Page 10
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics
For the latest User Installation Guide please visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
www.ergotron.com |
© 2015 Ergotron, Inc. All rights reserved.
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
10 of 10
|
China: 400-120-3051
|
Japan: japansupport@ergotron.com
888-45-031-01 rev. G • 09/19
Loading...