Ergotron 24-392-026 User Manual
™
WorkFit
Dual
User's Guide
A
Includes
Constant Force™
Technology
English
For the latest User Installation Guide please visit: www.ergotron.com
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
www.ergotron.com |
888-45-297-W-03 rev.N • 12/18
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
|
China: 400-120-3051
|
Japan: japansupport@ergotron.com
1 of 16
Safety
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted product and
equipment.
Adjust the height of your desk (or chair and footrest) to allow the keyboard to lower to your sitting elbow height for ergonomic computing.
Arm lowers along an arc.
Pull Arm toward you as
you lower from the
highest position.
827-975
CAUTION! Tipping Hazard. Support the stand until the clamp is securely
tightened. Failure to follow these instructions may result in the stand tipping
over causing possible equipment damages and or personal injury.
Arm lowers along an arc. Pull arm towards you as you lower from the highest
position.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these
instructions may result in equipment damage or personal injury.
Caution:
DO NOT route cables on top of arm. Failure to follow these instructions may result in equipment damage and/
or personal injury.
<
25
A+B+C+D
A
B
C
D
0.78"-2.56" (20-65mm)
6 - 14 lbs
(2.72-6.35 kg)
6 - 14 lbs
(2.72-6.35 kg)
< 5 lbs
(2.27 kg)
< 2 lbs
(0.9 kg)
lbs (11.3 kg)
A+B=
Important! You will need to adjust this product after
installation is complete. Make sure all your equipment
is properly installed on the product before attempting
adjustments. This product should move smoothly and
easily through the full range of motion and stay where you
set it. If movements are too easy or diffi cult or if product
does not stay in desired positions, follow the adjustment
instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take
many turns to notice a difference. Any time equipment is
added or removed from this product, resulting in a change
in the weight of the mounted load, you should repeat these
adjustment steps to ensure safe and optimum operation.
9-
20 lbs (4.1-9.1 kg)
2 of 16
0.78"-2.56" (20-65mm)
0.5"-2.5" (13-64mm)
888-45-297-W-03 rev.N • 12/18
360˚
5"
(127 mm)
20"
(508 mm)
85˚
ABCDEF
1
1x
1x
1x
2x
12x
M4 x 10mm
1x
2
1x
1x
3
8mm
4
1x
1x
1/4”
2x
5
2x
M5 x 35mm
6
1x
7
1x
M4 x 5mm
2x
M4 x 8mm
4x
1x
2x
M4x16mm
4x
M6 x 6mm
1x
4 mm
2x
1x
8x
M4 x 10mm
2x
8x
M6 x 45mm
1x
888-45-297-W-03 rev.N • 12/18
1/4"
3 of 16
1
Arm Extension and Desk Size:
The keyboard tray is designed to extend over the edge of your desk. You can expand the extension of the arm if
you need to based on your desk size. To determine if you need to expand your arm extension, refer to the 4 desk
dimensions below:
9.5"
(250 mm)
10"
(260 mm)
12.75"
(320 mm)
9.5"
(250 mm)
CLAMP
CAUTION: Base must be completely on desk surface.
Failure to follow these instructions may result in
equipment damage or personal injury.
GROMMET HOLE
6
6
12"
(300 mm)
With Expanded Arm Extension With Expanded Arm Extension
To expand the arm extension, follow instructions on
next page.
12.75"
(320 mm)
9.5"
(250 mm)
CLAMP
CLAMP
1 2
3 4
Grommet hole can
10"
(260 mm)
be located anywhere
along this arch.
12.75"
(320 mm)
GROMMET HOLE
GROMMET HOLE
Top View
To expand the arm extension, follow instructions on next page.
9.5"
(250 mm)
55
4 of 16
18"
(460 mm)
12.75"
(320 mm)
Grommet hole can
be located anywhere
along this arch.
16"
(410 mm)
(410 mm)
12.75"
(320 mm)
16"
12.75"
(320 mm)
Top View
888-45-297-W-03 rev.N • 12/18
How to expand the arm extension.
bcda
180˚
d1 d2 d3
Remove the 4 screws at the
base using the provided 4mm
hex wrench.
Flip the base around (turn
180 degrees.
180˚
Re-insert the 4 screws and tighten
with the 4mm hex wrench.
4 mm
888-45-297-W-03 rev.N • 12/18
5 of 16
Loading...