Page 1
™
WorkFit
Single LCD Mount, LD
A
User's Guide
Includes
Constant Force™
Technology
For the latest User Installation Guide please visit: www.ergotron.com
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
www.ergotron.com |
888-45-298-W-02 rev.M • 12/18
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
|
China: 400-120-3051
|
English
Japan: japansupport@ergotron.com
1 of 16
Page 2
Safety
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted product and
equipment.
Adjust the height of your desk (or chair and footrest) to allow the keyboard to lower to your sitting elbow height for ergonomic computing.
Arm lowers along an arc.
Pull Arm toward you as
you lower from the
highest position.
827-975
CAUTION! Tipping Hazard. Support the stand until the clamp is securely
tightened. Failure to follow these instructions may result in the stand tipping
over causing possible equipment damages and or personal injury.
Arm lowers along an arc. Pull arm towards you as you lower from the highest
position.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these
instructions may result in equipment damage or personal injury.
Caution:
DO NOT route cables on top of arm. Failure to follow these instructions may result in equipment damage and/
or personal injury.
<
20
5 - 15 lbs
(2.3-6.8 kg)
< 5 lbs
(2.27 kg)
C
lbs (9.1 kg)
< 2 lbs
(0.9 kg)
Important! You will need to adjust this product after
installation is complete. Make sure all your equipment
is properly installed on the product before attempting
adjustments. This product should move smoothly and
easily through the full range of motion and stay where you
set it. If movements are too easy or diffi cult or if product
does not stay in desired positions, follow the adjustment
instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take
many turns to notice a difference. Any time equipment is
added or removed from this product, resulting in a change
in the weight of the mounted load, you should repeat these
adjustment steps to ensure safe and optimum operation.
A+B+C
A
B
0.78"-2.56" (20-65mm)
2 of 16
0.78"-2.56" (20-65mm)
0.5"-2.5" (13-64mm)
888-45-298-W-02 rev.M • 12/18
Page 3
5"
(127 mm)
20˚
10˚
20"
(508 mm)
ABCDEF
1x
1
1x
2
1x
1x
1x
85˚
1x
M5 x 8mm
1x
M3 x 6mm
360˚
8x
M4 x 10mm
4x
3
4
1x
4x
1x
5
1x
6
1x
7
1x
1x
1x
2x
2x
M4x16mm
M6 x 45mm
8x
8mm
1x
2x
M4 x 10mm
1x
4 mm
1/4”
M5 x 35mm
888-45-298-W-02 rev.M • 12/18
1/4"
3 of 16
Page 4
1
Arm Extension and Desk Size:
The keyboard tray is designed to extend over the edge of your desk. You can expand the extension of the arm if
you need to based on your desk size. To determine if you need to expand your arm extension, refer to the 4 desk
dimensions below:
9.5"
(250 mm)
10"
(260 mm)
10"
(260 mm)
12.75"
(320 mm)
9.5"
(250 mm)
CLAMP
CAUTION: Base must be completely on desk surface.
Failure to follow these instructions may result in
equipment damage or personal injury.
GROMMET HOLE
Grommet hole can
6
be located anywhere
along this arch.
6
12"
(300 mm)
With Expanded Arm Extension With Expanded Arm Extension
12.75"
(320 mm)
CLAMP
CLAMP
1 2
3 4
To expand the arm extension, follow instructions on
next page.
9.5"
(250 mm)
18"
(460 mm)
12.75"
(320 mm)
12.75"
(320 mm)
GROMMET HOLE
GROMMET HOLE
Top View
To expand the arm extension, follow instructions on next page.
9.5" (250 mm)
55
16"
(410 mm)
Grommet hole can
be located anywhere
along this arch.
(410 mm)
12.75"
(320 mm)
16"
4 of 16
12.75"
(320 mm)
Top View
888-45-298-W-02 rev.M • 12/18
Page 5
How to expand the arm extension.
bcda
180˚
d1 d2 d3
Remove the 4 screws at the
base using the provided 4mm
hex wrench.
Flip the base around (turn
180 degrees.
180˚
Re-insert the 4 screws and tighten
with the 4mm hex wrench.
4 mm
888-45-298-W-02 rev.M • 12/18
5 of 16
Page 6
Clamp con gurations for di erent desk thickness
2
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure
mounting surface is strong enough to handle mounted product and equipment.
0.78"-1.78" (20-45mm) 1.70"-2.56" (43-65mm)
Mount arm to desk.
Tighten the bolts with the provided 8 mm wrench.
8mm
1/4”
4 mm
1/4"
CAUTION! Tipping Hazard. Support the stand
until the clamp is securely tightened. Failure
to follow these instructions may result in the
stand tipping over causing possible equipment
damages and or personal injury.
8
6 of 16
OPTIONAL GROMMET HOLE MOUNT
- Follow these instructions if you want to change your clamp to a grommet
hole mount.
7
888-45-298-W-02 rev.M • 12/18
Page 7
OPTIONAL GROMMET HOLE MOUNT
- Follow these instructions if you want to change your clamp to a grommet
hole mount.
Remove clamp bracket screws with
a
4mm hex wrench.
4 mm
Insert provided bolt into provided grommet
c
plate. Attach grommet plate with 4 mm hex
wrench and screws removed in step b.
1x
Remove clamp plate screws with
b
4mm hex wrench. Retain screws.
Position arm with attached grommet plate over
d
grommet hole (make sure bolt is centered in
hole). Thread grommet bracket and wing nut
onto bolt and tighten.
1x
1x
in hole.
1x
CAUTION: Bolt must be centered
0.78"-2.56"
(20-65mm)
0.5"-2.5"
(13-64mm)
888-45-298-W-02 rev.M • 12/18
7 of 16
Page 8
3
a
2x
M6 x 45mm
4 mm
b
2x
c
M5 x 35mm
WARNING!
Screws must be tightened to keep
product secure. Failure to follow these
instructions will create an unstable
situation and may result in equipment
damage or personal injury.
8 of 16
888-45-298-W-02 rev.M • 12/18
Page 9
4
a b
1x
2x
c
M4x16mm
888-45-298-W-02 rev.M • 12/18
9 of 16
Page 10
5
a
b
4 mm
1x
M5 x 8mm
6
1x
M3 x 6mm
0°
4x
M4 x 10mm
4x
M4 x 10mm
10 of 16
888-45-298-W-02 rev.M • 12/18
Page 11
7
a
b
1x
8
c
4x
1x
4x
M4 x 10mm
888-45-298-W-02 rev.M • 12/18
11 of 16
Page 12
9
NOTE: Leave enough slack in cable to allow full range of motion.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to
follow these instructions may result in equipment damage or personal injury.
8x
1x
Caution:
DO NOT route cables on top of arm.
Failure to follow these instructions
may result in equipment damage
and/or personal injury.
12 of 16
888-45-298-W-02 rev.M • 12/18
Page 13
10
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
a
1
1/4"
1/4”
8mm
2
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
3
888-45-298-W-02 rev.M • 12/18
13 of 16
Page 14
b
8mm
1/4”
1/4"
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
c
14 of 16
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
888-45-298-W-02 rev.M • 12/18
Page 15
d
8mm
1/4”
Increase Friction
If this product moves too easily from
side-to-side, then you'll need to
increase friction:
Decrease Friction
If this product is too diffi cult to move
from side-to-side, then you'll need to
decrease friction:
1/4"
e
f
8mm
1/4”
Increase Friction
If this product moves too easily, then
you'll need to increase friction:
Decrease Friction
If this product is too diffi cult to move,
then you'll need to decrease friction:
4 mm
Increase Friction
If this product moves too easily, then
you'll need to increase friction:
1/4"
888-45-298-W-02 rev.M • 12/18
Decrease Friction
If this product is too diffi cult to move,
then you'll need to decrease friction:
15 of 16
Page 16
f
Angle Setting Adjustment
Loosen these two screws.
1
Loosen or tighten this bolt to adjust tilt to desired angle.
2
4 mm
Tighten to tilt up.
Loosen to tilt down.
After desired tilt is achieved, retighten these
3
two screws to secure.
WARNING!
Screws must be tightened to keep product secure.
Failure to follow these instructions will create an
unstable situation and may result in equipment
damage or personal injury.
www.ergotron.com |
© 2015 Ergotron, Inc. All rights reserved. WorkFit™ is a registered trademark of Ergotron, Inc.
16 of 16
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
™
|
China: 400-120-3051
|
Japan: japansupport@ergotron.com
888-45-298-W-02 rev.M • 12/18
Loading...