Equator PLS600V, PLS602NFV, PLS602SV, PLS600 Series, PLS602 Series Service Manual And Spare Parts List

SERVICE MANUAL

&

SPARE PARTS CATALOG

Second edition – February 2006

COMPACT DISWASHER

MODELS

PLS 600 / 602 SERIES

3

EQUATOR ADVANCED Appliances

Service Manual : COMPACT DISHWASHER – PLS 600 / 602 SERIES

#

TABLE OF CONTENTS #

 Warranty Information ……………………………....…

 Troubleshooting……………………...………………..…. 4

 Exploded Views……………………………………....….. 10

 Parts List…………………………………………….……. 14

 Wiring Diagram…………………………….........…….. 17

 Simple parts breakdown…………………...…….……. 18

Page 2

EQUATOR ADVANCED Appliances

Service Manual : COMPACT DISHWASHER – PLS 600 / 602 SERIES

Page 3

EQUATOR ADVANCED Appliances

Service Manual : COMPACT DISHWASHER – PLS 600 / 602 SERIES

TROUBLESHOOTING

CAUSE SOLUTION

1.

c. The water supply hose is bent Check and stretch the hose.

e. REPAIR requirement.

2.

THE APPLIANCE DOES NOT GET WATER :-

a. There is no water supply

b. The pressure of the supplied

water is

too low.

d. The filter of the water supply

hose is choked.

SMOKE APPEARANCE AND SMELLING OF BURNED RUBBER :-

a. The appliance did not get water

Check the water supply network.
Check the water pressure

(must be 2 bar)

Clean the filter: For the model SUPER
AUTOMATIC, remove the back cover of
the appliance, remove the supply hose and
clean the filter. Fix the hose properly and
start a washing program (without dishes and
detergent inside) in order to check if the
appliance get water and if the fixing of the
hose is proper without any leakage. By the
end of program, fix the cover on the
appliance. For the models of PLS-Series, act
as above but without removing the back
cover. (On these appliances the supply hose
is fixed outside).
Possible malfunction:
a. Faulty water supply electrovalve
b. Faulty Pressostat

Let appliance cool down for a couple of
hours. Check the water pressure and
water supply hose for bending. Start new
washing program from the beginning. In
case that the problem insists, see 1d.

Page 4

EQUATOR ADVANCED Appliances

Service Manual : COMPACT DISHWASHER – PLS 600 / 602 SERIES

b. The appliance lose water (by

the draining hose) during the
washing program.

c. REPAIR requirement

3.

THE HEATING ELEMENT INDICATOR LIGHTS OFF AND ON DURING THE
PROGRAM :-

a. The appliance did not get water

b.The appliance lose water (by the
draining hose) during the washing
program.

c. REPAIR requirement

4.

WATER IS LEAKING FROM THE BOTTOM OF THE APPLIANCE

a. REPAIR requirement

In case that the water drained suddenly
during the program and some smoke
emitted, stop the program turn the timer
switch to the start point and after a
couple of hours start it on again. If the
problem insists, see 2b.

Possible malfunction:
a. Faulty door micro-switch.
b.Damaged pump coil.
c.Faulty safety thermostat.

Open the door, turn the timer switch to
the start point and start on the program
from the beginning. If the problem
insists, see Id.

In case that the water drained suddenly
at the time that the indicator lighted off
(realize it by opening the door at the
moment that the indicator turns off and
seeing that the water inside has been
drained), see 24c.

Possible malfunction:
a. Faulty heating element or It needs
cleaning from calcars.
b. Faulty safety thermostat.

:-

Possible malfunction:

a. Crevice on the tub.
b. Damaged flange of the pressure pump.
c. Damaged flange of thermostats on the tub.
d. Damaged pump connection hoses.

e. Loose hose clamps

Page 5

EQUATOR ADVANCED Appliances

Service Manual : COMPACT DISHWASHER – PLS 600 / 602 SERIES

5.

WATER IS LEAKING FROM THE EDGES OF THE DOOR :-

6.

a. Damaged door. Replace the door
b. Damaged water sprinkler. Possible side crevice on the sprinkler, it stops to

spin during the program and send the water not
upwards but to the door, causes the leakage.
Replace the water sprinkler.

c. Deficient water draining. In case that the appliance does not drain the hole

water quantity from inside, when it gets water
again, the water level goes high and causes the
leakage. See 7a.

c. Detergent residues on the edges of the
door.

e. REPAIR requirement Possible malfunction:

The detergent residues make a crust on the door
edges which lift the water level on these points
cause the leakage when the water sprinkler get
spin. Remove the door and clean it properly with a
sponge as well as the door frame on the cavity.
Install the door and start on the appliance from the
beginning.

a. Pressostat (change or adjust it)
b. Water supply electro valve.

WATER IS LEAKING FROM THE BACK OF THE APPLIANCE :-

7.

a. Damaged water sprinkler See 5b.
b. Damaged water supply hose or drain hose. Replace the damaged hose
c. REPAIR requirement Possible malfunction:

a. Faulty rinse-aid dispenser coil.
b. Faulty Pressostat pipe
c. Faulty door micro-switch.
d. Faulty door micro-switch rod.

THE APPLIANCE DOES NOT DRAIN THE WATER

:-

a. Bent draining hose Check and stretch the hose. In case that there is

water inside the tub, take it off with a sponge. Start
on the appliance from the beginning (without dishes
and detergent inside), in order to see if the
appliance drains properly.

b. REPAIR requirement Possible malfunction:

a. Blocked object inside the drain pump.
b. Open circuit.

Page 6