Epson Zip-100M, Zip-100S User Manual

®
EPSON
Installation/User’s Guide
For Macintosh and IBM Compatible PCs
with a SCSI Connection
Table of Contents
NSTALLING YOUR
MAC Users PowerBook Users PC Users
Installation Instructions
U
SING YOUR
ZIP D
ZIP D
RIVE
RIVE
Getting the Most of Your ZIP Drive
Drive Operation/Maintenance ZIP Tools Software SCSI Guidelines Troubleshooting
12 14 15 16 18
This guide shows how to install the SCSI model of the ZIP Drive on a Macintosh, or a PC that uses Windows, DOS or Windows 95. If you encounter any problems while installing your ZIP Drive, refer to “Troubleshooting” in the “Using Your ZIP Drive” section.
SCSI (Small
Computer System Interface)
Requirements

MAC USERS

All Macintosh computers have a built-in SCSI connector marked by the SCSI symbol + .
SCSI Connector
1

POWERBOOK USERS

Many PowerBook users already have a special PowerBook cable that provides a standard Mac SCSI connector. If you do not have one, you will need an HDI-SCSI adapter for the data cable before you can connect the ZIP Drive to a PowerBook. Check with your computer dealer, or call EPSON at 1-800-922-8911 to order a PowerBook adapter.

PC USERS

You need a SCSI connection to connect the ZIP Drive to your PC.
W
Refer to “SCSI Adapters” in the “Using Your ZIP Drive” section
for information on compatible adapters. Make sure the adapter
is installed in the computer before attempting to connect
your ZIP Drive.
SCSI Host Adapter (inside computer)
Computer Back
SCSI Connector
(from host adap
W
OS/2 Support: If you want to use your ZIP Drive in an OS/2
operating environment, you need to purchase EPSON driver software for OS/2. Call EPSON at 1-800-922-8911 to order, ($9.95 for shipping and handling), or use the EPSON Download Service at (310) 782-4531 to download a driver.
2

INSTALLATION INSTRUCTIONS

Unpack your ZIP Drive and accessories.
1
2
3
ZIP Manual and Install Floppy Disks
External Power
ZIP Drive
100MB ZIP Tools Disk
Turn off your computer’s power switch and pick up the ZIP data cable.
B
connecting the ZIP Drive.
Connect one end of the cable to the ZIP connector on the back of your drive.
(If the connector does not go on easily, try turning it over.
Tighten all connector screws.)
Always turn off computer power before
-
ZIP Connector
3
4
Connect the other end of the cable to the
SCSI connector on your computer.
MAC USERS
See illustration below.
POWERBOOK USERS
You need a special PowerBook cable or adapter to connect the ZIP Drive. Refer to the section for PowerBook Users at the start of this guide.
PC USERS
km
and NOT to a parallel port (printer port). The parallel port is the same size and shape as some SCSI adapter connectors, but the parallel port will not support this model of the ZIP Drive.
n If your adapter has a 50 pin SCSI connector: Use a 25 to
50 pin SCSI cable or cable converter to connect the ZIP Drive. If you need a cable or converter, call your computer dealer or contact EPSON at 1-800-922-8911.
Make sure you connect the ZIP cable to a SCSI connector
4
5
6
Optional: You can connect other SCSI devices to the ZIP Drive using another SCSI cable (usually a 25 to 50 pin cable).
You can also connect the ZIP Drive to the end of an existing SCSI chain by using a 25 to 50 pin SCSI cable or by using a cable converter with the ZIP data cable. When connecting the ZIP Drive to other SCSI devices, check the SCSI Guidelines in the “Using Your ZIP Drive” section to make sure the SCSI ID and termination on your ZIP Drive are set correctly.
To Another SCSI Device
To Computer or Previous SCSI Device
Connect the external power supply
(The power cord fits in the groove on the side of the ZIP Drive.)
m
Other power supplies may damage your ZIP Drive.
Use only an approved EPSON ZIP power supply,
W
Tip: To make it easier to move your ZIP Drive between home
and work, you may want to purchase an extra power supply and cable. Call EPSON at 1-800-922-8911 to order ZIP accessories.
5
Loading...
+ 16 hidden pages