Epson T7000, T5000, T3000-B Service Manual
SERVICE MANUAL
Large Format Color Inkjet Printer
SC-T7000 series SC-T5000 series SC-T3000 series
Confidential
SEIJ12008
Notice:
All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.
The contents of this manual are subject to change without notice.
All efforts have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly
appreciate being informed of them.
The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences thereof.
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
General Notice: Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their
respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2012 SEIKO EPSON CORPORATION.
COMMERCIAL PRINTER CS QUALITY ASSURANCE DEPARTMENT
Confidential
PRECAUTIONS
Precautionary notations throughout the text are categorized relative to 1) Personal injury and 2) Damage to equipment.
DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing
procedures preceded by DANGER Headings.
WARNING Signals a precaution which, if ignored, could result in damage to equipment.
The precautionary measures itemized below should always be observed when performing repair/maintenance procedures.
DANGER
1. ALWAYS DISCONNECT THE PRODUCT FROM THE POWER SOURCE AND PERIPHERAL DEVICES PERFORMING ANY MAINTENANCE OR
REPAIR PROCEDURES.
2. NO WORK SHOULD BE PERFORMED ON THE UNIT BY PERSONS UNFAMILIAR WITH BASIC SAFETY MEASURES AS DICTATED FOR ALL
ELECTRONICS TECHNICIANS IN THEIR LINE OF WORK.
3. WHEN PERFORMING TESTING AS DICTATED WITHIN THIS MANUAL, DO NOT CONNECT THE UNIT TO A POWER SOURCE UNTIL
INSTRUCTED TO DO SO. WHEN THE POWER SUPPLY CABLE MUST BE CONNECTED, USE EXTREME CAUTION IN WORKING ON POWER
SUPPLY AND OTHER ELECTRONIC COMPONENTS.
4. WHEN DISASSEMBLING OR ASSEMBLING A PRODUCT, MAKE SURE TO WEAR GLOVES TO AVOID INJURY FROM METAL PARTS WITH
SHARP EDGES.
WARNING
1. REPAIRS ON EPSON PRODUCT SHOULD BE PERFORMED ONLY BY AN EPSON CERTIFIED REPAIR TECHNICIAN.
2. MAKE CERTAIN THAT THE SOURCE VOLTAGES IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/RATING
PLATE. IF THE EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO
THE POWER SOURCE.
3. ALWAYS VERIFY THAT THE EPSON PRODUCT HAS BEEN DISCONNECTED FROM THE POWER SOURCE BEFORE REMOVING OR
REPLACING PRINTED CIRCUIT BOARDS AND/OR INDIVIDUAL CHIPS.
4. IN ORDER TO PROTECT SENSITIVE MICROPROCESSORS AND CIRCUITRY, USE STATIC DISCHARGE EQUIPMENT, SUCH AS ANTI-STATIC
WRIST STRAPS, WHEN ACCESSING INTERNAL COMPONENTS.
5. REPLACE MALFUNCTIONING COMPONENTS ONLY WITH THOSE COMPONENTS BY THE MANUFACTURE; INTRODUCTION OF SECONDSOURCE ICs OR OTHER NON-APPROVED COMPONENTS MAY DAMAGE THE PRODUCT AND VOID ANY APPLICABLE EPSON WARRANTY.
6. WHEN AIR DUSTER IS USED ON THE REPAIR AND THE MAINTENANCE WORK, THE USE OF THE AIR DUSTER PRODUCTS CONTAINING
THE INFLAMMABLE GAS IS PROHIBITED.
7. MAKE SURE AN ANTIVIRUS SOFTWARE IS INSTALLED ON THE COMPUTER USED FOR SERVICE SUPPORT. BE SURE TO HAVE THE
LATEST VIRUS DEFINITION FILE FOR THE SOFTWARE.
Confidential
About This Manual
This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included
herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page.
Manual Configuration
This manual consists of six chapters and Appendix.
CHAPTER 1.PRODUCT DESCRIPTIONS
Provides a general overview and specifications of the product.
CHAPTER 2.TROUBLESHOOTING
Describes the step-by-step procedures for the troubleshooting.
CHAPTER 3.DISASSEMBLY / ASSEMBLY
Describes the step-by-step procedures for disassembling and assembling the product.
CHAPTER 4.ADJUSTMENT
Provides Epson-approved methods for adjustment.
CHAPTER 5.MAINTENANCE
Provides preventive maintenance procedures and the lists of Epson-approved lubricants and
adhesives required for servicing the product.
CHAPTER 6.APPENDIX
Provides the following additional information for reference:
• Connectors
• Panel Menu Maps
• ASP List
• Exploded Diagrams
Confidential
Symbols Used in this Manual
Lubrication
Various symbols are used throughout this manual either to provide additional information on a specific topic or to warn of possible danger present during a procedure or an action.
Be aware of all symbols when they are used, and always read NOTE, CAUTION, or WARNING messages.
Indicates an operating or maintenance procedure, practice or condition that is necessary to keep the product’s quality.
Indicates an operating or maintenance procedure, practice, or condition that, if not strictly observed, could result in damage to, or destruction of, equipment.
May indicate an operating or maintenance procedure, practice or condition that is necessary to accomplish a task efficiently. It may also provide additional
information that is related to a specific subject, or comment on the results achieved through a previous action.
Indicates an operating or maintenance procedure, practice or condition that, if not strictly observed, could result in injury or loss of life.
Indicates that a particular task must be carried out according to a certain standard after disassembly and before re-assembly, otherwise the quality of the components
in question may be adversely affected.
Lubrication
Indicates that lubrication is needed for the parts after disassembly, when doing a maintenance or replacing a part with a new one.
Confidential
Revision Status
Revision Date of Issue Description
A October 1, 2012 First release
Chapter 2
• 2.3Remedies for Service Call Error(p.43):partially deleted
B March 6, 2013
Chapter4
• 4.1.2Adjustment Items and the Order by Repaired Part(p.199):partially revised
• 4.14.1Main Board initial setting(p.270):was added
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
Contents
Chapter 1 PRODUCT DESCRIPTION
1.1 Product Description ............................................................................................ 11
1.2 Basic Specifications ............................................................................................ 12
1.2.1 Basic Specifications ................................................................................... 12
1.2.2 Electric Specifications ............................................................................... 12
1.2.3 Ink Specifications ...................................................................................... 13
1.3 Printing Specifications ........................................................................................ 14
1.3.1 Paper Feed Specifications .......................................................................... 14
1.3.2 Supported Media ........................................................................................ 15
1.3.2.1 Epson Special Media Table ................................................................ 15
1.3.2.2 Usable Commercially Available Paper Size ...................................... 18
1.3.3 Printable area ............................................................................................. 20
1.3.4 Borderless Printing Specification .............................................................. 21
1.3.5 Stacker ....................................................................................................... 21
1.4 Hardware Specifications ..................................................................................... 22
1.4.1 Dimensions and Weight ............................................................................. 22
1.4.2 Installation Room Requirement ................................................................. 22
1.4.3 Part Names ................................................................................................. 23
1.5 Control Panel Specifications .............................................................................. 25
1.5.1 Control panel and LCD .............................................................................. 25
1.5.2 Menu Descriptions ..................................................................................... 27
1.5.3 Serviceman Mode ...................................................................................... 36
Chapter 2 TROUBLE SHOOTING
2.1 Overview ............................................................................................................ 40
2.1.1 Preliminary Check ..................................................................................... 40
2.1.1.1 Before performing troubleshooting .................................................... 40
2.1.1.2 Check for the usage environment ....................................................... 40
2.1.1.3 Recurrence check of the trouble ......................................................... 40
2.1.1.4 Check for the counter values/history .................................................. 40
2.1.1.5 Test print check .................................................................................. 40
2.1.2 Troubleshooting Procedure ........................................................................ 41
2.1.3 Procedure after troubleshooting ................................................................. 41
2.1.3.1 If the trouble has been successfully solved ........................................ 41
2.1.3.2 If necessary to escalate the trouble case ............................................. 41
2.2 Remedies for Maintenance Requests ................................................................. 42
2.3 Remedies for Service Call Error ........................................................................ 43
2.4 Remedies for Print Quality Troubles .................................................................. 58
2.5 Trouble on Paper Feeding .................................................................................. 62
2.6 Other Troubles .................................................................................................... 63
2.7 Trouble on Service Program ............................................................................... 64
2.8 Trouble on NVRAM Viewer .............................................................................. 65
Chapter 3 DISASSEMBLY & ASSEMBLY
3.1 Overview ............................................................................................................ 67
3.1.1 Precautions ................................................................................................. 67
3.1.2 Cautions after assembling .......................................................................... 69
3.1.3 Orientation Definition ................................................................................ 69
3.1.4 Recommended Tools ................................................................................. 70
3.2 Parts Diagram ..................................................................................................... 71
3.3 Disassembly Flowchart ...................................................................................... 78
3.4 Disassembly and Assembly Procedure ............................................................... 83
3.4.1 Preparation for servicing ........................................................................... 83
3.4.1.1 Unlocking the CR Unit ....................................................................... 83
3.4.2 Housing ...................................................................................................... 85
3.4.2.1 TOP COVER ...................................................................................... 85
3.4.2.2 FRONT COVER ................................................................................ 86
3.4.2.3 LOWER PAPER GUIDE ................................................................... 87
3.4.2.4 LOWER PAPER GUIDE B ............................................................... 88
3.4.2.5 IH COVER ......................................................................................... 89
3.4.2.6 WASTE INK TANK COVER ........................................................... 92
3.4.2.7 PRINTER COVER ............................................................................. 93
3.4.2.8 UPPER SUPPORT R COVER ........................................................... 94
3.4.2.9 RIGHT UPPER COVER & RIGHT ROLL COVER ........................ 95
3.4.2.10 RIGHT LOWER COVER ................................................................ 96
7
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
3.4.2.11 RIGHT BASE COVER .................................................................... 97
3.4.2.12 LEFT LOWER COVER ................................................................... 98
3.4.2.13 REAR RIGHT LOWER COVER .................................................... 99
3.4.2.14 UPPER LEFT COVER .................................................................. 100
3.4.2.15 LEFT UPPER COVER & LEFT ROLL COVER .......................... 101
3.4.2.16 LEFT BASE COVER ..................................................................... 102
3.4.2.17 FRONT LEFT LOWER COVER ................................................... 103
3.4.2.18 REAR LEFT LOWER COVER ..................................................... 104
3.4.2.19 REAR ROLL COVER FRAME ..................................................... 105
3.4.2.20 CARTRIDGE COVER SENSOR .................................................. 106
3.4.2.21 R WASTE INK COVER SENSOR ................................................ 107
3.4.2.22 L WASTE INK COVER SENSOR ................................................ 108
3.4.2.23 INTERLOCK SWITCH ................................................................. 109
3.4.3 Electric Circuit Components .................................................................... 111
3.4.3.1 MAIN BOARD ................................................................................ 111
3.4.3.2 MAIN-B BOARD ............................................................................ 113
3.4.3.3 MAIN-C BOARD ............................................................................ 114
3.4.3.4 SUB BOARD ................................................................................... 115
3.4.3.5 SUB-B BOARD ............................................................................... 117
3.4.3.6 PSH BOARD .................................................................................... 118
3.4.3.7 PANEL BOARD .............................................................................. 120
3.4.4 Carriage Mechanism / Ink System Mechanism ....................................... 122
3.4.4.1 CR COVER ...................................................................................... 122
3.4.4.2 DAMPER KIT .................................................................................. 123
3.4.4.3 PRINT HEAD .................................................................................. 126
3.4.4.4 HEAD FFC ....................................................................................... 127
3.4.4.5 CR FFC ............................................................................................. 131
3.4.4.6 CR SCALE ....................................................................................... 135
3.4.4.7 CR ENCODER ................................................................................. 138
3.4.4.8 CR TIMMING BELT ....................................................................... 139
3.4.4.9 CR MOTOR ..................................................................................... 141
3.4.4.10 CR HP SENSOR ............................................................................ 143
3.4.4.11 APG UNIT ..................................................................................... 144
3.4.4.12 PG SENSOR ................................................................................... 146
3.4.4.13 PUMP CAP UNIT .......................................................................... 147
3.4.4.14 IC HOLDER ................................................................................... 148
3.4.4.15 INK TUBE ..................................................................................... 152
3.4.4.16 CR UNIT ........................................................................................ 156
3.4.4.17 IM SENSOR ................................................................................... 159
3.4.4.18 PW SENSOR .................................................................................. 161
3.4.5 Paper Feed Mechanism ............................................................................ 163
3.4.5.1 PF MOTOR ...................................................................................... 163
3.4.5.2 PF SCALE ........................................................................................ 165
3.4.5.3 PF ENCODER .................................................................................. 166
3.4.5.4 PF TIMING BELT ........................................................................... 168
3.4.5.5 PRESSURE ROLLER ...................................................................... 170
3.4.5.6 PRESSURE ROLLER MOTOR ...................................................... 171
3.4.5.7 PRESSURE ROLLER SENSOR ..................................................... 173
3.4.5.8 ATC MOTOR .................................................................................. 175
3.4.5.9 PE SENSOR (ROLL PAPER) ......................................................... 177
3.4.5.10 PE SENSOR (THICK PAPER) ...................................................... 178
3.4.5.11 PAPER THICKNESS SENSOR .................................................... 180
3.4.6 Cutter Mechanism .................................................................................... 181
3.4.6.1 CUTTER UNIT ................................................................................ 181
3.4.7 Fans .......................................................................................................... 183
3.4.7.1 BOARD BOX FAN ......................................................................... 183
3.4.7.2 SUCTION FAN ................................................................................ 184
3.4.8 Auto Take-up Reel ................................................................................... 185
3.4.8.1 TAKE-UP REEL COVER ............................................................... 185
3.4.8.2 TAKE-UP REEL SENSOR ............................................................. 186
3.4.8.3 TAKE-UP REEL LED ..................................................................... 187
3.4.8.4 TAKE-UP REEL SWITCH ............................................................. 188
3.4.8.5 TAKE-UP REEL PS BOARD ......................................................... 190
3.4.8.6 TAKE-UP REEL MOTOR .............................................................. 192
3.4.8.7 TAKE-UP REEL MAIN BOARD ................................................... 194
Chapter 4 ADJUSTMENT
4.1 Overview .......................................................................................................... 198
4.1.1 Precautions ............................................................................................... 198
4.1.2 Adjustment Items and the Order by Repaired Part .................................. 199
4.1.3 Adjustment Items ..................................................................................... 211
4.1.4 List of Tools/Software/Consumables for Adjustments ........................... 219
4.1.5 Service Program Basic Operations .......................................................... 220
4.2 NV-RAM BACKUP/NVRAM Viewer ............................................................ 221
4.2.1 NVRAM Read Procedure ........................................................................ 221
4.2.2 NVRAM Write Procedure ....................................................................... 221
4.2.3 NVRAM Viewer Basic Operation ........................................................... 222
4.3 ADJUSTMENTS (Individual) ......................................................................... 227
4.4 ADJUSTMENTS (Sequence) ........................................................................... 228
8
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
4.5 Installing Firmware .......................................................................................... 229
4.6 Image Print ....................................................................................................... 230
4.7 Counter Reset ................................................................................................... 231
4.8 References ........................................................................................................ 232
4.9 Initial Ink Charge Flag ...................................................................................... 233
4.10 CR Related Adjustments ................................................................................ 234
4.10.1 CR Belt Tension Check ......................................................................... 234
4.10.2 APG Function Check ............................................................................. 237
4.10.3 Ink Mark Sensor Check & Auto Adjustment ........................................ 238
4.10.4 CR Scale Check ..................................................................................... 239
4.10.5 CR Active Damper Auto Adjustment .................................................... 240
4.10.6 Auto Uni-D Adjustment ........................................................................ 241
4.10.7 Auto Bi-D Adjustment, acceleration/deceleration print correction ....... 242
4.10.8 PW + T&B&S check and adjustment .................................................... 243
4.10.8.1 PW Adjustment .............................................................................. 243
4.10.8.2 T&B&S Adjustment ....................................................................... 243
4.10.9 PG Adjustment ....................................................................................... 245
4.11 Head Related Checks and Adjustments .......................................................... 248
4.11.1 Tube Inner Pressure Reduction .............................................................. 248
4.11.2 Head ID Input ........................................................................................ 249
4.11.3 Nozzle Check ......................................................................................... 251
4.11.4 Cleaning ................................................................................................. 252
4.11.5 Head Inclination Adjustment (CR direction) ......................................... 253
4.11.5.1 Head Inclination Auto Adjustment (CR direction) ........................ 253
4.11.5.2 Head Inclination Manual Adjustment (CR direction) .................... 254
4.11.5.3 Correcting Head Inclination (CR direction) ................................... 254
4.11.6 Head Slant Adjustment (PF direction) ................................................... 256
4.11.6.1 Head Slant Auto Adjustment (PF direction) .................................. 256
4.11.6.2 Head Slant Manual Adjustment (PF direction) .............................. 257
4.11.6.3 Correcting Head Slant (PF direction) ............................................. 258
4.12 Ink Supply Related Checks and Adjustments ................................................ 259
4.12.1 Ink eject ................................................................................................. 259
4.12.2 Cleaning (Tube Inner Cleaning) ............................................................ 260
4.12.3 Initial Ink Charge ................................................................................... 261
4.13 Media Feed Related Checks and Adjustments ............................................... 262
4.13.1 PF Belt Tension Check .......................................................................... 262
4.13.2 PC Scale Check ...................................................................................... 264
4.13.3 Media Feed Auto Adjustment ................................................................ 265
4.13.4 Cut Position Check & Adjustment ........................................................ 266
4.13.5 Paper Thickness Sensor Adjustment ..................................................... 267
4.13.6 Rear AD Adjustment ............................................................................. 269
4.14 Boards Related Checks and Adjustments ....................................................... 270
4.14.1 Main Board initial setting ...................................................................... 270
4.14.2 RTC & USB ID Input ............................................................................ 271
4.14.3 MAC Address Input ............................................................................... 272
4.14.4 Serial Number Input .............................................................................. 273
4.14.5 HDD S/N Information Writing .............................................................. 274
4.14.6 Board Replacement Date & Time Setting ............................................. 275
4.15 Other Printer Checks and Adjustments .......................................................... 276
4.15.1 Suction Fan Adjustment ........................................................................ 276
4.15.2 Panel Setting Reset & Job History Reset ............................................... 277
4.15.3 Operation Panel Check (LCD & Buttons) ............................................. 278
4.15.3.1 Panel LCD Operation Check .......................................................... 278
4.15.3.2 Panel Buttons Operation Check ..................................................... 278
4.15.4 Motor Measurement & Automatic Adjustment ..................................... 279
Chapter 5 MAINTENANCE
5.1 Overview .......................................................................................................... 281
5.2 Storing the Printer ............................................................................................ 282
5.3 Transportation .................................................................................................. 283
5.4 Exchange Parts ................................................................................................. 284
5.5 Cleaning ............................................................................................................ 285
5.6 Lubrication ....................................................................................................... 287
Chapter 6 APPENDIX
6.1 Block Wiring Diagram ..................................................................................... 291
6.1.1 Main Body ............................................................................................... 291
6.1.2 Auto Take-up Reel ................................................................................... 292
6.2 Connection Diagram ......................................................................................... 293
6.3 Panel Menu Map .............................................................................................. 309
6.4 Part names used in this manual ........................................................................ 312
6.5 Exploded Diagram/Parts List ........................................................................... 314
9
Confidential
PRODUCT DESCRIPTION
CHAPTER
1
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.1 Product Description
Models
SC-T7000 series: 1118 mm (44 inch); supports Super B0
SC-T5000 series: 914 mm (36 inch); supports Super A0
SC-T3000 series: 620 mm (24 inch); supports Super A1
Supported paper thickness
Up to 1.5 mm
Ink configuration
Brand-new water color pigment ink configuration with excellent black tone
important in quality CAD line drawing and highly vivid red essential for
commercial posters
Ink configuration: Cyan, Yellow, Magenta, Matte black, Photo black
High-speed throughput
Prints A1 plain paper in 28sec.
High print quality
For posters:
Excellent print quality in 4 colors, with resolution of up to 2800x1440
dpi, and in variable dot sizes (minimal 3.5 picoliter)
Space saving design
Front access design allows you to set the printer near a wall because you can
exchange the media, ink cartridges, maintenance box, and cutter from the front.
New driver and applications
Brand-new driver with simple UI
With the web UI OS-independent configuration and control of HDD through
the Web are available.
Provides the job monitoring and management functions using a job
monitoring tool.
Easy printing from Microsoft Office using dedicated plug-in software
Improved shorter occupancy time of the host PC
Occupancy time of the host PC has been significantly shortened with ESC/
Page and HP-GL2/RTL.
By adding the optional HDD unit, PC-less re-printing and more shortened
occupancy time become available.
Lower running cost
Independent ink cartridges for each color
high-capacity (700ml/350ml/150ml) ink cartridges
PC-less enlarged photocopy
For CAD:
High quality CAD line drawing achieved by optimizing the
combination of new inks and print modes
Media handling
Easier paper loading available thanks to the design for front-access and
spindle-less with optimal height based on ergonomics
Supports continuous printing of drawings or posters (in a standard size such as
A0, A1 or US-ANSI D/E)
Translucent printer cover allows you to check which roll paper is loaded
easily
Simply connecting a scanner enables PC-less enlarged photocopy.
Large sized LEDs
Equipped with large-sized LEDs for easier recognition of the printer’s error status
PRODUCT DESCRIPTION Product Description 11
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.2 Basic Specifications
1.2.1 Basic Specifications
Item Specification
Print method On-demand inkjet
Configuratio
n of nozzles
Maximum resolution 2,880 x 1,440dpi
Control code
Paper feed method Friction
RAM
Interface
Temperature
Humidity
Black
Color
For Main 512 MB
For Network 128 MB
Main body operation environment 10°C to 35 °C
When storing (packed)
When storing (unpacked)
Main body operation environment 20% to 80% (Non condensing)
When storing (packed) 5% to 85% (Non condensing)
When storing (unpacked) 5% to 85% (Non condensing)
360 nozzles x 2 lines x 2 colors (Photo
Black, Matte Black)
360 nozzles x 2 lines x 3 colors
(Yellow, Magenta, Cyan)
ESC/P Raster (commands are
nondisclosure)
HP-GL/2, HP-RTL
High-Speed USB
Ethernet (10Base-T/100Base-TX/
1000Base-T)
-20 °C to 60 °C
(within 120 hours under 60 °C, and
within 1 month under 40 °C)
-20 °C to 40 °C
(within 1 month under 40 °C)
1.2.2 Electric Specifications
Item
Rated voltage 100 to 240 VAC
Input voltage range 90 to 264 VAC
Rated current 1.0 A to 0.5 A 0.9 A to 0.5 A 0.8 A to 0.4 A
Rated frequency 50 to 60 Hz
Input frequency range 49.5 to 60.5 Hz
Power
consumption
Insulation resistance 10 MΩ or more (between AC line and chassis at 500 VDC)
Dielectric strength
Leek current 0.25 mA or less
Compliance with regulations
Operating Approx. 72 W Approx. 65 W Approx. 54 W
Sleep mode 3.0 W or less
Power OFF 0.4 W or less
SC-T7000 series SC-T5000 series SC-T3000 series
1.0 kV rms AC for 1 min. or 1.2 kV rms AC for 1 sec.
Conforms to International Energy Star Program
(Category: the harmonic restraint measure guideline)
Conforms to VCCI Class B (with full options installed)
Specification
(between AC line and chassis)
*Nozzle set configuration is;
Row A Row B Row C Row D Row E Row F Row G Row H Row I Row J
C M Y PKMKMKPK Y M C
PRODUCT DESCRIPTION Basic Specifications 12
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.2.3 Ink Specifications
Item Specification
Form Exclusive ink cartridge
Pigment ink
colors
Cartridge life See the date printed on the package (at normal temperature)
Guaranteed life
after
installation
Storage
Capacity 700 ml/350 ml/110ml
Dimensions
Black system: Photo Black, Matte Black
Color system: Yellow, Magenta, Cyan
1 year (after mounted in the printer)
Uninstalled (packed): -20 to 40 °C
(within 4 days under -20 °C, and within 1 month under 40 °C)
Installed: -20 to 40 °C
(within 4 days under -20 °C, and within 1 month under 40 °C)
Transporting (packed): -20 to 60 °C
(within 4 days under -20 °C, within 1 month under 40 °C, and within 72
hours under 60 °C)
700ml: W40 x L305 x H110 mm
350ml: W40 x L200 x H110 mm
110ml: W25 x L200 x H110 mm
PRODUCT DESCRIPTION Basic Specifications 13
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.3 Printing Specifications
1.3.1 Paper Feed Specifications
Item Specification
Paper feed method Friction feed
Return pitch 2.2049
Paper feeder
Feed speed
μm (1/11,520 inch)
Roll paper manual feed
Cut sheet manual feed
300ms/ (1/6 inch)
PRODUCT DESCRIPTION Printing Specifications 14
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.3.2 Supported Media
1.3.2.1 Epson Special Media Table
ROLL PAPER
Note "*1": SC-T3000 Series not supported
"*2": SC-T3000 Series/SC-T5000 Series not supported
"*3": When the optional auto take-up reel unit is used (SC-T7000 series)
"*4": Use the tensioner supplied with the auto take-up reel unit.
Size
Name
mm inch Forward Backward
406 16
Premium Glossy Photo Paper (250)
Premium Semigloss Photo Paper (250)
Premium Luster Photo Paper (260)
Premium Semimatte Photo Paper (260)
Photo Paper Gloss 250
610 24
*1
914
*2
1118
406 16
610 24
*1
914
*2
1118
254 10
300 11.8
406 16
508 20 -
610 24
*1
914
*2
1118
406 16
610 24
*1
914
*2
1118
432 17
610 24
*1
914
*2
1118
"*5": When a scanner is connected
"*6": U: Borderless printing available, but borders may appear or print quality decline due to paper
expanding or contracting.
*3
Head
Enlarged
*5
Alignment
ICC Profile
Thickness
(mm)
Core
Diameter
(inch)
Borderless
*6
Print
Take-up
EPSON SC-
*1
36
*2
44
0.27 3
√√√√√
T3000_5000_7000_Series Premium
Glossy Photo Paper 250.icc
EPSON SC-
*1
36
*2
44
0.27 3
√√√√√
√
--
T3000_5000_7000_Series Premium
Semigloss Photo Paper 250.icc
EPSON SC-
0.27 3
√√
√√
*1
36
*2
44
√
T3000_5000_7000_Series Premium
Luster Photo Paper 260.icc
EPSON SC-
*1
36
*2
44
0.27 3
√√√√√
T3000_5000_7000_Series Premium
Semimatte Photo Paper 260.icc
EPSON SC-
*1
36
*2
44
0.25 3
√√√√√
T3000_5000_7000_Series Photo
Paper Gloss 250.icc
PRODUCT DESCRIPTION Printing Specifications 15
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
Name
Premium Glossy Photo Paper (170)
Premium Semigloss Photo Paper (170)
Enhanced Synthetic Paper
Enhanced Adhesive Synthetic Paper
Doubleweight Matte Paper
Enhanced Matte Paper
Singleweight Matte Paper
Size
Thickness
(mm)
mm inch Forward Backward
420 (A2) ---
610 24
*1
914
1118
*2
36
44
420 (A2) ---
610 24
*1
914
1118
*2
36
44
*1
*2
*1
*2
0.18 2
0.18 2
Core
Diameter
(inch)
Borderless
*6
Print
-
√
-
√
Take-up
√√√ √
√√√ √
*3
610 24
1118
*2
*2
44
0.13 2
U
√√
610 24
1118
*2
*2
44
0.18 2
U
√√
610 24
914
1118
*1
*2
*1
36
*2
44
0.21 2
√√
*4
432 17
610 24
914 36
0.25 3
U
√
1118 44
432 17
610 24
*1
914
*2
1118
*1
36
*2
44
0.15 2
√√
*4
Enlarged
*5
Alignment
--
--
-
√√
--
-
√√
Head
√
ICC Profile
EPSON SCT3000_5000_7000_Series Premium
Glossy Photo Paper 170.icc
EPSON SCT3000_5000_7000_Series Premium
Semigloss Photo Paper 170.icc
EPSON SCT3000_5000_7000_Series Enhanced
Synthetic Paper.icc
EPSON SCT3000_5000_7000_Series Enhanced
Adhesive Synthetic Paper.icc
EPSON SCT3000_5000_7000_Series
Doubleweight Matte Paper.icc
EPSON SCT3000_5000_7000_Series Enhanced
and Archival Matte Paper.icc
EPSON SCT3000_5000_7000_Series
Singleweight Matte Paper.icc
PRODUCT DESCRIPTION Printing Specifications 16
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
CUT SHEET
Note "*1": SC-T3000 Series not supported
"*2": When a scanner is connected
"*3": U: Borderless printing available, but borders may appear or print quality decline due to paper expanding or contracting.
Name Size
Premium Glossy Photo Paper
Premium Semigloss Photo Paper
Premium Luster Photo Paper
Archival Matte Paper/Enhanced Matte
Paper
Photo Quality Inkjet Paper
Enhanced Matte Posterboard
Thickness
(mm)
Super A3/B
0.27
US-C
Super A3/B
0.27
US-C
Super B
0.27
US-C
Super A3/B
A2 -
US-C
Super A3/B
US-C
610 x 762 mm
(24" x 30")
762 x 1016 mm
(30" x 40")
*1
0.26
0.12
1.30 - - - EPSON SC-T3000_5000_7000_Series Enhanced Matte Poster Board.icc
Borderless
U
U
U
U
U
U
U
U
U
U
*3
Enlarged
*2
Head Alignment ICC Profile
√√
√√
√√
-
-
√
√
EPSON SC-T3000_5000_7000_Series Premium Glossy Photo Paper.iccA2 -
EPSON SC-T3000_5000_7000_Series Premium Semigloss Photo Paper.iccA2 -
EPSON SC-T3000_5000_7000_Series Premium Luster Photo Paper.iccA2 -
EPSON SC-T3000_5000_7000_Series Enhanced and Archival Matte
Paper.icc
EPSON SC-T3000_5000_7000_Series Photo Quality Ink Jet Paper.iccA2 -
PRODUCT DESCRIPTION Printing Specifications 17
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.3.2.2 Usable Commercially Available Paper Size
This printer supports the following paper specifications for non-Epson media.
C A U T I O N
Do not use paper that is wrinkled, scuffed, torn, or dirty.
Although plain paper and recycled paper manufactured by
other companies can be loaded and fed in the printer as long as
they meet the following specifications, Epson cannot guarantee
the print quality.
Although other paper types manufactured by other companies
can be loaded in the printer as long as they meet the following
specifications, Epson cannot guarantee the paper feeding and
print quality.
ROLL PAPER
Item Specification
Media types Plain paper and recycled paper
Paper core size 2 inch and 3 inch
Roll paper outer
diameter
Width
Paper thickness 0.08 to 0.5 mm
Basis weight 64 to 90g/m
Available width for
borderless printing
150 mm or less
SC-T7000 Series: 254 mm (10 inches) to 1,118 mm (44 inches)
SC-T5000 Series: 254 mm (10 inches) to 914 mm (36 inches)
SC-T3000 Series: 254 mm (10 inches) to 610 mm (24 inches)
2
254 mm/10 inch
300 mm/11.8 inch
Super A3/B/329 mm
406 mm/16 inch
17 inch
B2/515mm
A1/594mm
610 mm/24 inch
728 mm
A0/841 mm
914 mm/36 inch
1030 mm
1118 mm/44 inch
PRODUCT DESCRIPTION Printing Specifications 18
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
CUT SHEET
Item Specification
Media types Plain paper and recycled paper
SC-T7000 Series: 210 mm (A4) to 1,118 mm (44 inches)
Width
Length 279.4 to 1,580 mm
Paper thickness 0.08 to 0.8 mm
Available width for
borderless printing
SC-T5000 Series: 210 mm (A4) to 914 mm (36 inches)
SC-T3000 Series: 210 mm (A4) to 610 mm (24 inches)
254 mm/10 inch
300 mm/11.8 inch
Super A3/B/329 mm
406 mm/16 inch
17 inch
B2/515 mm
A1/594 mm
610 mm/24 inch
728 mm
A0/841 mm
914 mm/36 inch
1030 mm
1118 mm/44 inch
PRODUCT DESCRIPTION Printing Specifications 19
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.3.3 Printable area
ROLL PAPER
Note "*1": SC-T7000 Series
"*2": SC-T5000 Series
"*3": SC-T3000 Series
"*4": If “Banner” is selected for “Roll Paper Option” in the printer driver “Advanced” tab, the top
and bottom margins are 0 mm.
㪁㪈
㪁㪉
0mm/3mm
㪁㪊
㪁㪋
C
㪁㪋
A
3mm/15mm
D
3~45mm
127mm
15m
3mm/15mm
~
B
254mm~1118mm
254mm~914mm
254mm~620mm
Table 1-1. Roll Paper Margin
Roll Paper Margin Parameter Margin Values
A = 45mm
Top45mm/Bottom15mm
C =15mm
B, D = 3mm
3mm A, B, C, D = 3mm
15mm A, B, C, D = 15mm
When “Normal” is selected, the value for A is 20 mm for the following paper.
Premium Glossy Photo Paper (250) / Premium Semigloss Photo Paper (250) / Premium
Luster Photo Paper (260) / Premium Semimatte Photo Paper (260)
When the following media are used in the “CAD / Line Drawing” mode, the value for
A and C is 3 mm.
Singleweight Matte Paper
CUT SHEET
Table 1-1. Roll Paper Margin
Roll Paper Margin Parameter Margin Values
*
Normal
Top15mm/Bottom15mm
A, C = 15mm
B, D = 3mm
A, C = 15mm
B, D = 3mm
A = 35mm
Top35mm/Bottom15mm
C =15mm
B, D =3mm
PRODUCT DESCRIPTION Printing Specifications 20
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.3.4 Borderless Printing Specification
AVAILABLE PAPER TYPE
For the paper types and sizes that support the borderless printing, see "1.3.2.1 Epson
Special Media Table" (p15).
ROLL PAPER CUTTING OPERATION
Printer driver
settings
Borderless The default printer driver setting is “Borderless”.
Single Cut
Cutting Operation Explanation
A
B
The top area may become slightly uneven
depending on the image since the print
operation stops while cutting the top edge of
the roll paper.
If the cut position is misaligned slightly, small
A
B
parts of the image may be shown on the top or
bottom of the adjacent pages. If this occurs,
perform “Adjust Cut Position”.
When printing only one page the operation
performed is the same as that for “Double Cut”.
When continuously printing multiple sheets,
the printer cuts 1 mm inside on the top edge of
the first page and the bottom edge of the
subsequent pages to avoid showing margins.
Printer driver
settings
Double Cut
Cutting Operation Explanation
The top area may become slightly uneven
depending on the image since the print
operation stops while cutting the top edge of
the roll paper.
A
B
The printed paper is approximately 2 mm
shorter than the specified size since the printer
cuts the paper inside the image to avoid
showing top and bottom margins.
After cutting the bottom edge of the previous
page, the printer feeds the paper, and then cuts
the top edge of the following page. Although
this produces 60 to 127 mm cut-off pieces, the
cut is more accurate.
1.3.5 Stacker
Table 1-2. Continuous Stacker
Stackable Pages
Paper size Paper Type
A1 594 x 841mm
A0 841 x 1,189mm --- 20 pages 20 pages
Plain paper
Table 1-3. Single Sheet Stacker
SC-T3000 Series SC-T5000 Series SC-T7000 Series
Approx. 1,292 mm Approx. 1,292 mm Approx. 1,575 mm
SC-T3000
Series
20 pages 20 pages 20 pages
Maximum Length
SC-T5000
Series
SC-T7000
Series
PRODUCT DESCRIPTION Printing Specifications 21
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.4 Hardware Specifications
This section provides the printer dimensions and shows the main components.
1.4.1 Dimensions and Weight
Model Width Depth
SC-T7000 Series 1,608 mm 813 mm 1,128 mm Approx. 82 kg
SC-T5000 Series 1,405 mm 813 mm 1,128 mm Approx. 75 kg
SC-T3000 Series
(w/o dedicated stand)
SC-T3000 Series
(w/ dedicated stand)
Note 1: When the paper basket is retracted
2: Excluding ink cartridges
1,050 mm 691 mm 613 mm Approx. 51 kg
1,050 mm 813 mm 1,128 mm Approx. 61 kg
*1
Height Weight
1.4.2 Installation Room Requirement
*2
Figure 1-1. SC-T7000 Series/SC-T5000 Series
Figure 1-2. SC-T3000 Series
PRODUCT DESCRIPTION Hardware Specifications 22
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.4.3 Part Names
FRONT SIDE
Figure 1-3. Front Side
Table 1-4. Front Side
No. Name
1 Printer cover
2 Poster board support
3 Maintenance box covers
4 Paper basket
5Casters
6Stack guides
7 Stack guide switch lever
8 Cartridge cover
9 Ink cartridges
10 AC inlet
11 Option port
12 LAN port
13 Data light
14 Status light
15 USB port
16 Control panel
17 Alert lamp
18 Roll rest
19 Adapter guides
20 Roll lock lever
21 Adapter holder
22 Paper slot
23 Print head
24 Roll paper cover
25 Paper eject guide
PRODUCT DESCRIPTION Hardware Specifications 23
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
ROLL PAPER ADAPTER
Figure 1-4. Roll paper adapter
Table 1-5. Roll paper adapter
No. Name
1 Adapter lock lever
2 Size lever
PRODUCT DESCRIPTION Hardware Specifications 24
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.5 Control Panel Specifications
1.5.1 Control panel and LCD
CONTROL PANEL
Figure 1-5. Control panel
Table 1-6. Control panel
Name Function
1 Power button Turns the power on and off.
On: The power is on.
Flashing: The printer is receiving data or cleaning the
2 Power light
Off: The power is off.
3 Load/Remove Paper button Displays the Load/Remove Paper menu.
4 Screen
5 [Menu] button
6 Back button
7 Left/Right buttons Use these buttons to select tabs.
8 Up/Down buttons
9 OK button
10 Help button Displays the Help menu.
11 Maintenance button
12 Pause/Cancel button
13 Feed/Cut Media button
Displays the printer’s status, menus, error messages, and
so on.
Displays the menu for the tab currently selected in the
display.
If menus are displayed, pressing this button takes you up
one level in the menu hierarchy.
When menus are displayed, these buttons can be used to
highlight items or options.
Displays the menu for the tab currently selected in the
display.
When menus are displayed and an item is highlighted,
pressing this button displays the sub-menu for the
highlighted item.
If pressed while a parameter is selected from the Menu,
the parameter is set or executed.
Displays the Maintenance menu, which is used for nozzle
checks and head cleaning.
The printer enters pause status if this is pressed while
printing.
Pressing this button while a menu or help is displayed
closes the menu or help and returns the printer to ready
status.
It is used to manually cut roll paper using the built-in
cutter.
If printing is not currently in progress and the printer is
loaded with roll paper, you can feed paper ahead by
pressing first this button and then the [T] button.
print head or performing other operations in
the course of being shut down.
PRODUCT DESCRIPTION Control Panel Specifications 25
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
LCD
Screen View
Name Function
1 Message
Figure 1-6. LCD
Table 1-7. LCD
Displays the printer’s status, operation, and error
messages.
Tabs/Info
2
Display Area
Table 1-7. LCD
Name Function
Print
Queues Tab
Paper Tab
Ink Tab
Displays print job status and can be used to access the
Print Queues menu.
Shows the type of paper in the printer and can be used to
access the Paper menu.
Displays ink status.
The ink cartridge status is indicated as follows.
: No error.
: Ink is low.
: Ink cartridge is expended.
: An error occurred.
: Non-genuine cartridge is installed.
Shows the status of the Maintenance Box and is used to
display the Maintenance menu.
Maintenance Box status is shown as follows.
Maintenance
Tab
Setup Tab Displays the IP address and menus for various settings.
Enlarged
Copy Tab
Displayed only when a scanner is connected.
: No error.
: The Maintenance Box is nearing the end of
its service life.
: Maintenance Box is at the end of its service
life.
PRODUCT DESCRIPTION Control Panel Specifications 26
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
1.5.2 Menu Descriptions
Note "*1": Displayed only when optional hard disk unit is installed.
Table 1-8. Menu List
Menu Menu Item / Setting Value (Shaded one is the default) Explanation
Lists the estimated start time and time needed to print the selected job.
It also predicts whether the job can be completed without replacing paper, ink or the
Maintenance Box. Printing can proceed even if “Can Not Complete” is displayed.
However, the printer may run out of ink or paper during printing.
Remote Manager and the LFP HDD Utility display the reason for the “Can Not
Complete” message and allow you to hold or cancel the job.
The printer will only predict availability on the basis of the amount of paper
remaining if “On” is selected for “Roll Paper Remaining”.
The printer will not predict availability on the basis of the amount of ink remaining
when documents are printed using LFP Print Plug-In for Office or EPSON
CopyFactory5.
This option is available only if “On” is selected for “Store Held Job” in the Setup
menu.
Displays the print settings for held jobs and the reason the job is held.
Jobs that are held because the job print settings differ from those currently selected
for the printer can be printed as described below.
1. Replace the paper and take whatever other steps may be necessary to ready the
device for printing.
2. Select “Resume All Jobs”.
Shows the status of the selected stored job when it was last printed.
After viewing the job, press the [OK] button to enter the number of copies. Press the
[S]/[T] buttons to choose the number of copies and press the [OK] button to display
the estimated print time and print availability. Press the [OK] button to start printing.
Print Queues menu
Waiting Job Name
User
Estimated Start
Print Queue
Hold Queue
Saved Job Queue
Print Job Log Sheet Press the [OK] button to print the print job log.
*1
*1
XXXXXXXXXXX
(name of queued print job)
XXXXXXXXXXX
View Hold Queue
Resume All Jobs Press the [OK] button to resume all held jobs currently in the queue.
XXXXXXXXXXX (name of stored print
*1
job)
(name of held print
job)
Time
Estimated Print
Time
Printing
Availability
Paused Job Name
User
Paper Type
Source
Size
Reason For Hold
Stored Job Name
User
Length
Pages
Paper Type
Copies
Source
Size
Estimated Print
Time
PRODUCT DESCRIPTION Control Panel Specifications 27
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
Table 1-8. Menu List
Menu Menu Item / Setting Value (Shaded one is the default) Explanation
Press the [OK] button to view instructions for removing the paper. Follow the onscreen instructions to remove the paper.
Instructions are not displayed if no paper is loaded.
Highlight the paper to be loaded and press the [OK] button. Follow the on-screen
instructions to load the paper.
If paper is already loaded in the printer, the instructions for removing the loaded
paper type will be displayed before loading instructions are shown.
You can select the media type that is the closest to the paper you are using.
Select the platen gap which is the distance between the print head and the paper.
Normally, select “Standard”. Select a wider setting if printed images are smeared. If,
upon performing head alignment you feel that it is still not completely aligned, select
“Narrow”.
Paper menu
Load/Remove Paper
Select Paper Type
Custom Paper
Setting
Remove Paper
Roll Paper
Cut Sheet (up to 0.8
mm thick)
Poster Board
Photo Paper
Matte Paper
Plain Paper
Others
Custom Paper Select the name of the custom paper loaded in the printer.
Select Reference
Paper
XXXXXXXXXXX
(name of custom
paper type)
Platen Gap
Detect Paper
Thickness
Select the type of paper loaded.
Photo Paper
Matte Paper
Plain Paper
Others
No Paper Selected Select this option if you do not wish to specify the paper type.
Narrow
Standard
Wide
Wider
Press the [OK] button to print a pattern to determine the thickness of the current paper.
Select the pattern number with the least misalignment from the print results.
PRODUCT DESCRIPTION Control Panel Specifications 28
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
Table 1-8. Menu List
Menu Menu Item / Setting Value (Shaded one is the default) Explanation
Pattern Use this setting if you are unable to resolve banding issues (horizontal striped lines or
uneven colors) in the standard print area (for cut sheets, the area excluding the 1 to 2
cm strip at the bottom of the paper) even after head cleaning or head alignment.
When “Pattern” is selected;
Press the [OK] button to print an adjustment pattern. Measure the distances between
the “+” symbols in the printed adjustment pattern. Use only the distance between the
center symbols or the average of the distances between the left, center, and right
symbols.
Paper menu
Custom Paper
Setting
XXXXXXXXXXX
(name of custom
paper type)
Paper Feed Adjust
Value
Paper Suction -4 to 0
Normal
Roll Paper Tension
Extra High
After the adjustment pattern is printing, the length of the pattern will be displayed in
the control panel. Press the [S]/[T] buttons to enter the measured value and press
the [OK] button.
When “Value” is selected;
Choose an adjustment between -0.70 and +0.70%. Selecting too small a value causes
dark bands; adjust the amount upward. Similarly, choosing too large a value causes
white bands; adjust the amount downward.
It is important to choose the appropriate amount of suction for the paper used in order
to maintain the correct distance between the paper and the print head. Choosing too
high a value for thin or soft paper will increase the distance between the paper and the
print head, causing print quality to decline or preventing the paper feeding correctly.
If this happens, lower the paper suction. The suction power is weakened when the
parameter is lowered.
Select “High” or “Extra High” if the paper wrinkles during printing.High
PRODUCT DESCRIPTION Control Panel Specifications 29
Confidential
SC-T7000 series/SC-T5000 series/SC-T3000 series Revision B
Table 1-8. Menu List
Menu Menu Item / Setting Value (Shaded one is the default) Explanation
Custom Paper
Paper menu
Maintenance menu
Setup menu Printer Setup Roll Paper Setup
Setting
Print Paper List Press the [OK] button to print a list of custom paper settings.
Nozzle Check
Head Cleaning
Head Alignment
Cutter Maintenance
XXXXXXXXXXX
(name of custom
paper type)
Auto(Uni-D)
Auto(Bi-D)
Manual(Uni-D)
Manual(Bi-D)
Adjust Cut Position -3 to 3 mm
Replace Cutter
Remove Skew
Setting Name
Restore Settings
Auto Cut
Refresh Margin
Page Line
On
Off
Enter a name of up to 22 characters for custom paper settings. Choose an easy-to-remember name for quick
selection.
Yes
No
Press the [OK] button to print a nozzle check pattern. Visually inspect the printed pattern and perform head
cleaning if you notice faint or missing areas.
Inspect the printed pattern and select the check boxes for patterns with faint or missing areas. To select all
nozzles, place a check in the box on the left.
If print results are grainy or out of focus, perform head alignment to realign the print head. If “Auto” is
selected, the printer will scan the printed pattern during printing and realign the head automatically.
If “Manual” is selected, a pattern will be printed; inspect the pattern visually and enter the value you think
appropriate.
Moves the cutter to the replacement position so it can be replaced. Press the [OK] button to move the cutter
to the replacement position. The paper must be removed before replacing the cutter.
On Choose “On” to automatically cut roll paper using the built-in cutter as each page is
Off
On If “On” is selected during borderless printing, the printer will automatically trim the
Off
On If “Auto Cut” is “Off”, you can choose to print (“On”) or not print (“Off”) cut lines
Off
Select whether to enable (“On”) or disable (“Off”) paper skew reduction.
Restore the selected custom paper settings to default values.
You can fine tune the cut position when printing to roll paper with no margins in all
directions. The cut position can be adjusted in increments of 0.2 mm.
printed, “Off” to disable auto paper cutting. The setting selected with the printer
driver takes priority when the printer driver is used.
leading edge to remove any ink stains that may have been left by the previous copy;
to disable this feature, choose “Off”.
on roll paper. Cut lines are not printed if “Auto Cut” is “On” or when cut sheets or
poster board is used.
Note, however, that if the roll width selected with the computer is narrower than the
paper loaded in the printer, cut lines will be printed regardless of the option selected
for “Auto Cut”.
The setting selected with the printer driver takes priority when the printer driver is
used.
PRODUCT DESCRIPTION Control Panel Specifications 30
Confidential
Loading...