* Ink thaws and is usable after approximately 3 hours at 77 °F (25 °C).
Caution:
To ensure good results, use genuine Epson ink cartridges and do
not refill them. Other products may cause damage to your printer
not covered by Epson’s warranty. Do not use an ink cartridge if the
date on the package has expired.
Envelopes
SizeNo. 10 (4.1 × 9.5 inches)
Paper typePlain bond paper
Weight20 to 24 lb (75 to 90 g/m²)
Note:
Poor quality paper may reduce the print quality and cause paper jams
or other problems. If you have print quality problems, switch to a
higher grade paper.
Do not load curled or folded paper.
Use paper only under these conditions:
Temperature: 59 to 77 °F (15 to 25 °C)
Humidity: 40 to 60% RH
Printable Area
Single sheets
NormalBorderless*
A
B-LB-R
C
Paper
Note:
Since the quality of any particular brand or type of paper may be
changed by the manufacturer at any time, Epson cannot guarantee
the quality of any non-Epson brand or type of paper. Always test a
sample of paper stock before purchasing large quantities or printing
large jobs.
3.5 × 5inches
8 × 10 inches
User Defined up to 8.5 × 44 inches
Paper typePlain bond paper or special paper
distributed by Epson
Thickness0.003 to 0.005 inch (0.08 to 0.13 mm)
Weight17 to 24 lb (64 to 90 g/m²)
(for plain bond paper)
* When printing with the borderless feature, print quality may decline in the
expanded area. Before printing large jobs using the borderless setting, print a
single sheet to confirm printout quality.
Envelopes
A:The minimum top margin is 0.12” (3 mm).
B-L:The minimum left margin is 0.12” (3 mm);
0.20” (5 mm) for envelopes.
B-R:The minimum right margin is 0.12” (3 mm);
0.20” (5 mm) for envelopes.
C:The minimum bottom margin is 0.12”
(3 mm).
DThe minimum bottom margin is 0.78”
(20 mm) for envelopes.
Note:
Always load paper into the sheet feeder with the short edge first.
Load envelopes flap edge left with the flap side down.
210/06
Page 3
Epson Stylus CX7000F Series
Scanning
Scanner typeFlatbed color
Photoelectric deviceCIS
Effective pixels10,200 × 14,040 pixels at 1200 dpi
Document size8.5 × 11.7 inches (216 × 297 mm)
A4 or US letter size
Scanning resolution1200 dpi (main scan)
2400 dpi with Micro Step Drive
™
(sub scan)
48 bit (input) 24 bit (output)
Output resolution50 to 4800, 7200, and 9600 dpi
(50 to 4800 dpi in 1 dpi increments)
Scanning speedColor: Approx. 15 msec per line
at 600 dpi
Image data16 bits per pixel per color internal
8 bits per pixel per color external
(maximum)
InterfaceOne USB port
Light sourceRGB three color LED
Mechanical
Paper pathSheet feeder, top entry
Sheet feeder capacity About 100 sheets at 17 lb (64 g/m²)
DimensionsWidth: 18.2 inches (463 mm)
Depth: 13.9 inches (353 mm)
Height: 7.2 inches (184 mm)
(with the output tray and
paper support closed)
Weight15.2 lb (6.9 kg) without the ink
cartridges
Electrical
Input voltage90 to 132 V
Rated frequency50 to 60 Hz
Rated current1.2 A
Power consumptionApprox. 18 W (operating)
Approx. 10 W in idle mode
Approx. 1 W in power-off mode
Environmental
TemperatureOperation: 50 to 95 °F (10 to 35 °C)
Storage: –4 to 104 °F (–20 to 40 °C)
HumidityOperation: 20 to 80% RH
Storage: 5 to 85% RH
(without condensation)
USB Interface
StandardBased on Universal Serial Bus
Specifications Revision 2.0
Bit rate480 Mbps (high speed device)
Adaptable connector USB Series B
Cable lengthLess than 6.6 feet (2 meters)
Safety Approvals
SafetyUL 60950-1 (U.S.)
CSA C22.2 No. 60950-1 (Canada)
EMCFCC part 15 Subpart B Class B (U.S.)
CAN/CSA-CEI/IEC CISPR 22
Class B (Canada)
Telecom regulations FCC Part 68 (U.S.)
ICC CS03 (Canada)
Memory Card Slots
Compatible CompactFlash
memory cardsSmartMedia
Memory Stick
Memory Stick PRO
Memory Stick Duo™*
Memory Stick PRO Duo
MagicGate
MagicGate Memory Stick Duo
Microdrive
SD™ (Secure Digital)
SDHC
miniSD™*
miniSDHC*
microSD*
microSDHC*
MultiMediaCard
xD-Picture Card
xD-Picture Card Type H
xD-Picture Card Type M
Voltage 3.3 V
requirementsMaximum current is 500 mA
* Adapter required
Memory Card Slot Compatibility
CF Type II Compatible with CF+ and
card slotCompactFlash Specification 3.0 cards
SmartMediaCompatible with SmartMedia
card slotStandard 2000 cards
®
™
™
®
Memory Stick
™
™
™
™
*
™
*
™
™
10/063
Page 4
Epson Stylus CX7000F Series
Memory Stick/Compatible with Memory Stick
MemoryStick PRO Standard version 1.42-00 or Memory
card slotStick Standard Memory Stick PRO
Specification Version 2.0 cards and
MultiMediaCard Standard Version 4.1
cards
xD-Picture Compatible with xD-Picture cards.
card slotCard Specification Version 1.20 cards
Type Hand Type M cards
Memory Card Image File Requirements
Media formatDCF version 1.0 or 2.0 compliant*
File formatJPEG
Supports Exif version 2.21
Image size80 × 80 pixels to 9200 × 9200 pixels
Number of filesUp to 999
* DCF is the “Design rule for Camera File system” standard
3. Flip the feeder guard forward.
4. Insert the paper, printable side up, against the right edge
guide and beneath the tabs. (The printed side is whiter or
brighter on some papers.) Always load paper short edge first,
even for landscape printing.
Place paper beneath the tabs
Loading Paper
1. Open the paper support and slide out the extensions.
2. Open the output tray and pull out the extension.
You can load up to 100 sheets of plain paper and up to
20 sheets of photo or matte paper (see page 5 for capacity
guidelines on other paper types).
Note:
The type of paper you choose affects the way your printout
looks, so be sure to select the correct paper for your job. If you
are just making a copy or printing a rough draft of an image, plain
paper is fine. However, for the best results, you’ll want to use
one of Epson’s special ink jet papers designed for your printer.
For example, your photos will look great printed on Epson Ultra
Premium Photo Paper Glossy (see page 1 for more information).
5. Slide the left edge guide against the left edge of the paper
(but not too tightly).
410/06
Page 5
Epson Stylus CX7000F Series
6. Flip the feeder guard back.
Follow these guidelines when loading paper:
❏ Don’t load paper above the arrow on the left edge guide.
Make sure the paper is under the tabs on the left and right
edge guides.
❏ Load the printable side face-up. It’s often brighter or whiter
than the other side.
❏ Always load the short edge first, even when printing in
landscape mode.
❏ Load letterhead or preprinted paper into the printer
top edge first.
❏ If you experience paper feeding problems, try loading fewer
sheets.
❏ If you’re using special paper, check the package for special
loading instructions.
Note:
For instructions on loading envelopes, see the User’s Guide.
Paper Loading Capacity
Selecting the Correct Media Type Setting
The table below lists the settings you should choose for your
paper in the printer software:
Paper
Plain paper
Epson Bright White Paper
Epson Premium Bright White Paper
Epson Ultra Premium Photo Paper Glossy
Epson Ultra Premium Glossy Photo Paper
Epson Premium Photo Paper Glossy
Epson Premium Glossy Photo Paper
Epson Photo Paper Glossy
Epson Glossy Photo Paper
Epson Premium Photo Paper Semi-gloss
Epson Premium Semigloss Photo Paper
Epson Premium Presentation Paper Matte
Epson Matte Paper Heavyweight
Epson Premium Presentation Paper Matte
Double-sided
Epson Double-Sided Matte Paper
Epson Presentation Paper Matte
Epson Photo Quality Ink Jet Paper
Epson Photo Quality Self-Adhesive Sheets
Epson Iron-On Transfer Paper
PremierArt Matte Scrapbook Photo Paper
for Epson
EnvelopesEnvelope
Type or Media Type
setting
Plain Paper /
Bright White Paper
Ultra Premium Photo
Paper Glossy
Premium Photo Paper
Glossy
Photo Paper Glossy
Premium Photo Paper
Semi-Gloss
Premium Presentation
Paper Matte
When loading Epson ink jet papers, follow these capacity
guidelines:
Paper type
Epson Bright White Paper
Epson Premium Bright White Paper
Epson Ultra Premium Photo Paper Glossy
Epson Ultra Premium Glossy Photo Paper
Epson Premium Photo Paper Glossy
Epson Premium Glossy Photo Paper
Epson Premium Photo Paper Semi-gloss
Epson Premium Semigloss Photo Paper
Epson Photo Paper Glossy
Epson Glossy Photo Paper
Epson Premium Presentation Paper Matte
Epson Matte Paper Heavyweight
Epson Premium Presentation Paper Matte
Double-sided
Epson Double-Sided Matte Paper
Epson Presentation Paper Matte
Epson Photo Quality Ink Jet Paper
Epson Photo Quality Self-Adhesive Sheets
Epson Iron-On Transfer Paper
PremierArt Matte Scrapbook Photo Paper for Epson
Loading
capacity
80 sheets
20 sheets
100 sheets
1 sheet
Placing Originals on the Glass
1. Open the document cover and place your original
face-down on the glass, in the upper left corner.
10/065
Page 6
Epson Stylus CX7000F Series
2. Close the document cover gently so that your original does
not move.
Caution:
Do not place heavy objects on the document table glass, and do
not press the glass with too much force. Do not open the
document cover beyond where it stops.
Placing Large or Thick Documents
When you scan a large or thick document, you can remove the
document cover. Just open it and pull it straight up.
If you need to press the document flat while you copy or
scan it, do not press too hard and be careful not to move it.
Caution:
Do not use excessive force on the document cover, and do not
twist it diagonally. You may damage the document cover.
When you are done, replace the document cover by inserting
the tabs back into the slots.
Copying
You can make copies using letter-size (8.5× 11-inch),
4 × 6-inch, and 5× 7-inch plain or photo paper.
Copying a Document
1. Press the P On button to turn
on the CX7000F Series. You
see a screen like this:
2. Place the document on the glass as described on page 5. Be
sure to close the document cover.
3. Load up to 100 sheets of letter-size plain paper. See page 4
for details.
4. Press the
Copy button. You see
this display:
5. If you want your copies
automatically reduced or
enlarged to fit the loaded paper
Fit to Page mode), press
size (
the
Copy button again. The
display changes to this:
6. To make multiple copies (up to 99), press the number keys
on the numeric keypad. The display shows the number you
select.
Note:
To exit Copy mode, press the
7. Press the paper type button to select Plain Paper. The light
indicates which type is selected.
8. Press the paper size button to select
9. To make a color copy, press the x
To make a black and white copy, press the x
button.
Printing appears on the display and the CX7000F Series starts
copying.
If you need to stop copying, press the y
Do not pull out paper that is being printed; it will be ejected
automatically to the output tray.
Note:
The copies may not be exactly the same size as the original.
12:00 PM Y
Copies:1 100%
Copies:1 FitPage
y Cancel/Back button.
Letter.
Start Color/OK button.
Start B&W
Cancel/Back button.
Copying a Photo
1. Press the P On button to turn
on the CX7000F Series. You
see a screen like this:
2. Place the photo on the glass as described on page 5. Be sure
to close the document cover.
3. Load up to 20 sheets of letter-size, 4 × 6-inch, or 5 × 7-inch
photo paper (see page 4 for details).
4. Press the
Copy button. You see
this display:
12:00 PM Y
Copies:1 100%
610/06
Page 7
Epson Stylus CX7000F Series
5. If you want borderless photos
(printed without a white
border), press the
again to select
mode. (If you select
Copy button
Fit to Page
100%,
photos are printed with a
border.) The display changes to
Copies:1 FitPage
this:
6. To make multiple copies (up to 99), press the number keys
on the numeric keypad. The display shows the number you
select.
Note:
To exit Copy mode, press the
y Cancel/Back button.
7. Press the paper type button to select Photo Paper.
8. Press the paper size button to select
5"× 7".
9. To make a color copy, press the x
To make a black and white copy, press the x
Letter, 4"× 6", or
Start Color/OK button.
Start B&W
button.
Printing appears on the display and the CX7000F Series starts
copying.
If you need to stop copying, just press the y
Cancel/Back
button. Do not pull out paper that is being printed; it will be
ejected automatically to the output tray.
Note:
The copies may not be exactly the same size as the original.
When making a lot of copies, it is a good idea to remove the printed
copies from the output tray after every 10 sheets or so.
Making a Quick Copy
If you want to make a copy quickly and do not need high
quality, you can print a “draft” copy. The print quality is
reduced, but the copy is printed faster.
1. Load plain, letter-size paper and select
Letter size on the control panel.
2. Press the
Copy button. If you want your copies
Plain Paper and
automatically reduced or enlarged to fit the loaded paper
size, press the
Copy button again to select Fit to Page
mode.
3. When you are ready to copy, press and hold the y
button, then press and hold the x Start Color/OK
Back
button (to copy in color). When you see
on the display, release both buttons.
Color Draft Mode
Printing appears on
Cancel/
the display.
To make a black and white copy, press and hold the
Cancel/Back button, then press and hold the x Start
y
B&W button. When you see B/W Draft Mode on the
display, release both buttons.
Printing appears on the
display.
Printing From a Memory Card
Inserting the Memory Card
1. Make sure the CX7000F Series is turned on.
2. Open the memory card door.
3. Make sure the memory card access light is off and that no
cards are in any of the slots. Then insert your card into the
correct slot. The memory card access light flashes and then
stays on.
Insert just one card at a time
Left slot
Memory card
access light
Right slot
10/067
Page 8
Epson Stylus CX7000F Series
SlotType of card
Right slotCompactFlash
Microdrive
Left slotSD
SDHC
miniSD*
miniSDHC*
microSD*
microSDHC*
MultiMediaCard
Memory Stick
Memory Stick Duo*
Memory Stick PRO
Memory Stick PRO Duo*
MagicGate Memory Stick
MagicGate Memory Stick Duo*
SmartMedia
xD-Picture Card
xD-Picture Card Type H
xD-Picture Card Type M
* Adapter required
4. Now you can:
❏ Print an index sheet so you can select which photos to
print (see below)
❏ Print all the photos on the card (see page 9)
❏ Print photos pre-selected on your camera using DPOF
(see page 9)
4. If the light in the
Card button is not lit, press
the
Memory Card button.
The CX7000F Series counts
Memory
Number of images (varies)
the images on your card and
you see this display, indicating
it is ready to print the index
1.Img:92 Prt Idx
sheet:
5. Make sure
6. Press the x
button. You see this display:
7. Press the x
Plain Paper and Letter are selected.
Start Color/OK
Start Color/OK button again. The CX7000F
1.Prt Idx: File
Series starts printing the index sheet(s). This may take a few
minutes.
When you want to remove the card, make sure the memory
card access light is not flashing, then pull the card straight out
of its slot.
Caution:
Do not remove the card or turn off the CX7000F Series while the
memory card access light is flashing; you may lose data on the
card.
Printing an Index Sheet
You can print an index sheet (which is like a photographer’s
contact or proof sheet) to see small “thumbnail” images of all
the pictures on your card. Then you can mark the pictures on
the index sheet that you want to print, scan the sheet, and let
the CX7000F Series automatically print the selected photos.
1. Make sure your CX7000F Series is not connected to your
computer (or make sure your computer is turned off).
2. Load several sheets of letter-size, plain paper. (Use only
letter-size paper to print the index sheet.) Up to 30 images
are printed on each page, so if there are more than 30
photos on the memory card, you’ll need enough sheets for
all the index pages to be printed.
3. Insert the memory card if it is not already in the slot (as
shown on the left).
For multiple index sheets, the pages containing the most
recent images are printed first. If you want to cancel
printing more sheets, press the y
Cancel/Back button.
Now follow the instructions below to select which photos to
print.
Selecting Photos on the Index Sheet
1. Once you have printed the index sheet, use a dark pen or
pencil to fill in one of the circles beneath each photo you
want to print to indicate how many copies you want (1, 2,
or 3).
OK:
Incorrect:
Make sure just one circle is filled in for each selected photo
and mark the sheet carefully; once it has been scanned you
will not be able to change your selections.
Note:
If you want one copy of all the photos on the index sheet, fill in
the ALL oval at the top of the page.
810/06
Page 9
Epson Stylus CX7000F Series
2. Place the index sheet face-down on the glass, in the upper
left corner, so that the top of the sheet is aligned against the
left edge of the glass.
3.Close the document cover.
Note:
Don’t remove the memory card while you’re printing from an
index sheet.
4. Load up to 100 sheets of plain paper or up to 20 sheets of
photo paper at a time (see page 4 for details). You can load
more paper later as necessary to print all your selected
photos.
The display should now look
like this, indicating that the
CX7000F Series is ready to
scan the index sheet:
If this setting is not displayed, press the
2.Img:92 Scn Idx
Memory Card
button until it is displayed.
5. Select
Plain Paper or Photo Paper (whichever you
loaded).
If you select
border. If you select
Plain Paper, the photos print with a white
Photo Paper, the photos print
borderless, to the edge of the paper.
6. Select
7. Press the x
Letter, 4"x 6", or 5"x 7" for the paper size.
Start Color/OK button to start printing.
Note:
If you need to stop printing, press the y Cancel/Back button.
8. When you are done printing, wait until the memory card
access light is not flashing, then remove the memory card by
pulling it straight out of its slot.
Printing All Photos or DPOF Photos
Follow the steps below to print one copy of each photo on the
card or to print only those photos that were pre-selected with
your camera’s DPOF (Digital Print Order Format) feature.
1. Load up to 100 sheets of plain paper or up to 20 sheets of
photo paper at a time (see page 4 for details.) You can load
more paper later as necessary to print all your photos.
2. Insert the memory card (see page 7 for details).
3. Press the
Memory Card
button repeatedly, until the
display looks something like
3.Img:92 All/DPO
this:
Note:
If the memory card does not contain DPOF information, one copy
of all the photos on the card will be printed.
4. Select Plain Paper or Photo Paper (whichever you
loaded).
If you select
border. If you select
Plain Paper, the photos print with a white
Photo Paper, the photos print
borderless, to the edge of the paper.
5. Select
6. Press the x
Letter, 4"× 6", or 5"× 7" for the paper size.
Start Color/OK button to start printing.
Note:
If you need to stop printing, press the y Cancel/Back button.
If you see the Paper Out message, load more paper and press
the
x Start Color/OKbutton.
When you are done printing, wait until the memory card
access light is not flashing, then remove the memory card by
pulling it straight out of its slot.
Printing From a Digital Camera
If your camera is PictBridge™- or USB DIRECT-PRINT™compatible, you can print your JPEG photos by connecting
your digital camera directly to your CX7000F Series. Your
photos must be sized from 80 × 80 pixels to 9200 × 9200
pixels.
1. Make sure your CX7000F Series is not printing.
2. Remove any memory cards from slots.
3. Load the type of paper you want to use (see page 4). Load
enough sheets for the number of photos you’ll be printing.
4. Press the paper type button to select
borderless photos (without a white border). Select
Paper
if you want your photos printed with a small white
border.
Photo Paper to print
Plain
10/069
Page 10
Epson Stylus CX7000F Series
5. Press the paper size button to select
5"x 7".
Letter, 4"x 6", or
6. Connect the USB cable that came with your camera to the
camera and the USB connector on the front of your
CX7000F Series.
7. Make sure your camera is
turned on. The following
appears on the display screen:
PictBridge
8. Select the photos you want to print with your camera. Then
adjust any necessary settings and print your photos as
explained in your camera manual.
Note:
Depending on the CX7000F Series settings and your digital
camera settings, some combinations of paper type, size, and
layout may not be supported. In addition, some of your digital
camera settings may not be reflected in the printed output.
Epson cannot guarantee the compatibility of any camera.
Connecting a Phone or Answering
Machine
If you’re connecting the CX7000F Series to a phone line, and
connecting a telephone or answering machine to the same
phone line so you can use it to make voice calls, follow these
steps:
1. Connect the phone cable leading from the wall jack to the
LINE port.
2. Connect one end
of another phone
cable to the
telephone or
answering
machine.
3. Connect the other end of the phone/answering machine
cable to the
You also need to set up your CX7000F Series to receive faxes
manually (see page 13 for details).
EXT port on the back of the CX7000F Series.
Setting Up Your Fax Features
Before sending or receiving faxes, you may want to create a fax
header and select your fax preferences.
Creating Header Information
1. Press the Fax button once to
enter Fax mode. The
button lights up and you see
this display:
2. Press the
Setup button. You
see this display:
3. Press the u or d button, or
press the
6 key on the numeric
keypad, to display this option:
4. Press the x
Start Color/OK
button. You see this display:
5. Press the x
Start Color/OK button again. The display goes
blank except for the cursor (_).
6. Press the keys on the numeric keypad to enter up to 28
digits of header information. Use the number keys to enter
the letters A to Z (in uppercase or lowercase), the numbers 0
to 9, and various symbols.
Press a key repeatedly to display first the numbers and
symbols (if available), then the uppercase and lowercase
letters, as indicated on the key. Then wait a moment or
press the
r button to move to the next character space.
When you’re finished, press the
blank space.
Note:
If you need to change a character to the left, press the l key to
delete the character and re-enter it. Press the r key if you need
to move the cursor to the right.
7. Press the x Start Color/OK button. You return to the
1.Fax Header Setup display.
8. Press the u or d button, or
press the
2 key on the numeric
keypad, to display this option:
9. Press the x
Start Color/OK
button. You see this display (to
indicate the two-digit month,
day, and year):
10. Press the keys on the numeric keypad to enter the date. You
can enter the numbers 0 to 9.
11. Press the x
Start Color/OK
button. You see this display (to
indicate the hour and minute):
Fax
Enter Fax Number
1.Select Speed D
6.Header & Time
1.Fax Header Set
r button to move to a
2.Date/Time
MM:DD:YY
HH:MM AM
1010/06
Page 11
Epson Stylus CX7000F Series
12. Press the keys on the numeric keypad to enter the time in a
12-hour format. You can enter the numbers 0 to 9.
13. Press the x
button. You see this display:
14. Press the
key to select
15. Press the x
2.Date/Time display.
Start Color/OK
1:AM 2:PM
1 key on the numeric keypad to select AM or the 2
PM.
Start Color/OK button. You return to the
16. If you want to print your fax
number in the fax header, press
the u or d button, or press the
3 key on the numeric keypad,
3.Your Phone Num
to display this option:
17. Press the x
Start Color/OK button. The display goes blank
except for the cursor (_).
18. Press the keys on the numeric keypad to enter your fax
number. You can enter the numbers 0 to 9, and the
characters * and #, up to 20 digits total.
19. Press the x
20. Press the y
Start Color/OK button.
Cancel/Back button until you return to the
screen displaying the date.
Selecting the Paper Size
Before you receive a fax, be sure to load plain paper and set the
Paper Size setting to the size of paper you’ve loaded. Also
make sure the
Automatic Reduction setting is set to receive
faxes in the desired size (see the next section for details).
Selecting Send/Receive Settings
Your CX7000F Series is set up to send and receive faxes using
the default settings below. For more information about these
and other fax settings, see the User’s Guide.
Indicates the size of the paper loaded in
the CX7000F Series for printing received
faxes.
Indicates whether large received faxes
are reduced in size to fit on the selected
Paper Size or printed at their original size
on multiple sheets.
Indicates whether or when the CX7000F
Series prints a report for outgoing faxes.
Select Off to turn off report printing, On Error to print reports only when an error
occurs, or On Send to print reports for
every fax you send.
Indicates the type of phone system to
which you’ve connected the CX7000F
Series.
Setting and OptionsDescription
DRD
All (default)
Single
Double
Triple
Double & Triple
ECM
On (default)
Off
V.34
On (default)
Off
Rings to Answer
5 (default)
1, 2, 3, 4, 5, 6, 7, 8, or 9
Indicates the type of answer ring pattern
you want to use to receive faxes. You
must have set up your phone system to
use different ring patterns to select an
option other than All.
Indicates whether you use Error
Correction Mode to automatically
request retransmission of fax data that is
received with detected errors.
Indicates the speed at which you
transmit faxes.
On is 33.6 Kbps and Off 14.4 Kbps.
Indicates the number of rings that must
occur before the CX7000F Series
automatically receives a fax.
To change the fax settings listed above, follow these steps:
1. Press the
enter Fax mode. The
button lights up and you see
this display:
2. Press the
see this display:
Fax button once to
Fax
Setup button. You
Enter Fax Number
1.Select Speed D
3. If you need to change the
Paper Size, Automatic
Reduction, or Last
Transmission Report
settings, press the u or d
button, or press the
the numeric keypad, to display
this option:
4. Press the x
Start Color/OK
button. You see this display:
5. Press the u or d button, or press the
4 key on
4.Scan & Print S
1.Resolution
3, 4, or 5 key on the
numeric keypad, to display one of these options:
❏ 3.Paper Size
❏ 4.Automatic Reduction
❏ 5.Last Transmission Report
Then press the x Start Color/OK button.
6. Press the u or d button until the setting option you want is
displayed, then press the x
Start Color/OK button to
select it.
7. Repeat steps 5 and 6 to change any other settings. When
you’re finished, press the y
to the
4.Scan & Print Setup menu.
Cancel/Back button to return
10/0611
Page 12
Epson Stylus CX7000F Series
8. If you need to change the
Mode, DRD, ECM, V.34, or
Rings to Answersettings,
Dial
press the u or d button, or
press the
keypad, to display this option:
9. Press the x
button. You see this display:
10. To change the Dial Mode setting, press x
5key on the numeric
Start Color/OK
5.Communication
1.Dial Mode: Ton
Start Color/OK
and go to step 11.
To change another Communication setting, press the
u or d button, or press the
2, 3, 4, or 5 key on the numeric
keypad, to display one of these options:
❏ 2.DRD
❏ 3.ECM
❏ 4.V.34
❏ 5.Rings to Answer
Then press the x Start Color/OK button.
11. Press the u or d button until the setting option you want is
displayed, then press the x
Start Color/OK button to select
it.
12. Repeat steps 10 and 11 to change any other settings. When
you’re finished, press the y
Cancel/Back button to return
to the screen displaying the date.
Sending a Fax
Before you fax, place your original photo or document on the
document table glass. Then send your fax by manually
entering a fax number or redialing the previous fax number.
You can also set up and select an entry from your speed dial
list (see the Basics Guide for more information).
If you want to redial the last fax number you used, press the
Redial/Pause button instead of entering a fax number. The
last fax number appears on the screen.
3. To send a black and white fax, press the x
Start B&W
button.
To send a color fax, press the x
Start Color/OK button.
You see this display during
faxing:
Note:
If you need to cancel faxing at any time, press the y Cancel/Back
button.
4. After your original is scanned,
you see this screen:
If you do not need to fax another page, press the
Scanning 001 98%
Send another pag
2 key (for
No). The CX7000F Series dials the fax number and faxes
your document.
Note:
If the fax number is busy or there is some other connection
problem, you see an error message and the CX7000F Series
redials the number after one minute. Wait for the redial, or check
your connection and settings and try faxing again.
If you need to fax another page, press the 1 key (for Yes).
Open the document cover, remove your first original, place
your next original, and close the document cover. Then
press the x
Start Color/OK button to fax the next page.
Repeat this step to fax all the necessary pages.
Note:
If you’re sending a color fax, or a large document that fills up the
memory area, the CX7000F Series scans and faxes one page at a
time. It then asks if you want to send another page. The fax
connection stays open until you are finished.
Receiving a Fax
Manually Entering or Redialing a Fax
Number
1. Press the Fax button once to
enter Fax mode. The
button lights up and you see
this display:
2. Press the keys on the numeric
keypad to enter the fax
number. You can enter the
numbers 0 to 9 and the
characters * and #, up to 64 digits total.
Note:
If you need to change a character to the left, press the l button
to delete the character and re-enter it. Press the r button if you
need to move the cursor to the right.
1210/06
Fax
Enter Fax Number
1234567890
The CX7000F Series automatically receives and prints faxes in
Auto Answer mode. However, you may want to receive faxes
manually if you connected the CX7000F Series and a phone
or answering machine to a phone line that also receives voice
calls. Then you can check for a fax tone from the sending fax
machine and press a button on the CX7000F Series to receive
the fax, or allow your answering machine to determine if the
call is an incoming fax.
Note:
Make sure you selected the Paper Size
of paper you’ve loaded. If the incoming fax pages are larger than the
paper size you loaded, the fax size is reduced to fit or printed on
multiple pages, depending on the Automatic Reduction setting you
select (see page 11 for details).
setting that matches the size
Page 13
Epson Stylus CX7000F Series
f
Selecting the Answer Mode
The CX7000F Series tells you
whether Auto Answer is
turned on or not on the first
screen:
12:00 PM Y
Y: Auto Answer is turned on
12:00 PM N
To change the answer mode,
press the
button. The
N (for No)changes on the screen. Press Auto Answer again
Auto Answer
Y (for Yes) or
to change it back.
You can select the number of rings that must occur before the
CX7000F Series receives a fax using the Rings to Answer setting
(see page 11 for details).
N: Auto Answer is turned of
Receiving Faxes
When the CX7000F Series receives a fax with Auto Answer
mode turned on, the message
When the CX7000F Series receives a fax in manual answer
mode, the connected phone begins ringing. Once you answer
the phone to confirm that the call is a fax, press the
Start B&W or x Start Color/OK button to receive the fax.
x
The message
Printing appears on the display.
After the CX7000F Series receives all the pages, it begins
printing the fax. When it’s finished, you see the screen
displaying the date.
Printing appears on the display.
Scanning Directly From Epson Scan
You can scan from any TWAIN-compliant application—such
as ArcSoft PhotoImpression
start Epson Scan directly from your computer and save your
image to a file.
1. Open the document cover and place your original facedown on the glass, in the upper left corner.
Note:
If you need to scan a thick document, you can remove the
document cover (see page 6).
2. Close the cover gently so you don’t move the original.
3. Do one of the following to start Epson Scan:
❏ Windows
®
: Double-click the EPSON Scan icon on
your desktop.
❏ Macintosh
®
: Double-click EPSON Scan in the
Applications folder.
❏ If you are scanning from an application, start your
application. Then open the File menu, choose
or Acquire, and select EPSON Stylus CX7000F Series
(your program may use different scanning commands).
You see the Epson Scan standby window:
™
—using Epson Scan. Or you can
Import
Note:
If you run out of paper during printing, you see the error message
Paper out. Load more paper and press the
so printing can continue. If you see any other error messages, see
page 19.
x Start Color/OK button
Scanning
You can use your CX7000F Series to scan a photo or
document and save it to computer. You can even
automatically restore faded color photographs as you scan (see
page 14 for details). The Epson Scan software provides three
scanning modes for progressive levels of control over your
scanned image:
❏
Full Auto Mode scans quickly and easily using automatic
settings.
Home Mode previews your image and provides automatic
❏
image adjustments, cropping tools, and preset options for
various types of scans.
❏
Professional Mode previews your image and lets you
manually configure your scan settings with a full array of
tools.
4. If the Mode setting in the upper right corner is set to
Auto Mode, click the Scan button.
Note:
If you want to automatically restore a color photo as you scan,
click the Customize button (see the next section for
instructions).
If you are in Home or Professional Mode, you see a
different Epson Scan settings window. You can change the
mode using the Mode selector in the upper right corner (see
the on-screen User’s Guide for details).
Full
10/0613
Page 14
Epson Stylus CX7000F Series
5. You see the File Save Settings window:
Choose the location where you want to save your scanned
file and type a name for it in the Prefix box. Select a file
format in the Image Format box.
6. Click
OK. The image is scanned and you see its icon or
filename in an open folder.
Restoring Color in Faded Photos
You can automatically transform an old, faded, or badly
exposed color photo into one with true-to-life color and
sharpness as you scan. Look for the
in Epson Scan’s Full Auto, Home, and Professional Mode
windows:
1. Place your original photo on the scanner as described on
page 5.
2. Start Epson Scan (see the previous section for instructions).
3. When the Epson Scan window appears, do one of the
following, depending on the currently selected scan mode:
Color Restoration option
4. Select the basic settings for the type of original(s) you are
scanning, then select the destination setting for the way you
will use your image(s) (see the on-screen User’s Guide for
instructions).
5. Click the
Preview button to preview your image(s), then
select your scan area.
6. Do one of the following to select the Color Restoration
option:
❏ Home Mode: Click the
Color Restoration checkbox.
❏ Professional Mode: Scroll down to the Adjustments
area and click the
Color Restoration checkbox.
7. Make any other necessary image adjustments.
8. Size your image as necessary.
9. Click the
Scan button to scan and restore the color in your
image(s).
Checking the Print Head Nozzles
❏ Home or Professional Mode: go to step 4.
❏ Full Auto Mode: click the
Color Restoration checkbox, and click OK. Continue
Customize button, click the
with step 9.
1410/06
If your printouts are faint or have gaps in them, some of the
nozzles in the print head may be clogged or ink may be
running low in one or more of the ink cartridges. Follow the
steps below to check the print head nozzles and remaining ink
levels using the control panel.
1. Load letter-size paper in the sheet feeder.
2. Press the P
On button to turn
on the CX7000F Series, or
press the y
button until you see a screen
Cancel/Back
12:00 PM Y
like this:
3. Press the
see this display:
Setup button. You
1.Load/Eject
4. Press the u or d button, or
press the
3 key on the numeric
3.Nozzle Check
keypad, to display this option:
Page 15
Epson Stylus CX7000F Series
5. Press the x Start Color/OK button. The CX7000F Series
prints a test pattern like this:
Print head
nozzles are clean:
Print head needs
to be cleaned:
6. Press the y
Cancel/Back button to return to the screen
displaying the date.
If the pattern does not look good, try cleaning the print head
as described below.
Cleaning the Print Head
If your printouts are unexpectedly light or faint, or you notice
light or dark bands across your printout, you may need to
clean the print head. This unclogs the nozzles so they can
deliver ink properly. Run a nozzle check (as described in the
previous section) to see if the print head needs cleaning.
Note:
Print head cleaning uses ink, so clean it only if quality declines and the
nozzle check indicates that the print head needs to be cleaned.
1. Press the P On button to turn
on the CX7000F Series, or
press the y
button until you see a screen
like this:
2. Press the
see this display:
3. Press the u or d button, or
press the
keypad, to display this option:
4. Press the x
runs a head cleaning cycle and the message
appears on the display.
5. Never turn off the CX7000F Series while head cleaning is in
progress. You may damage it.
6. When the display returns to
check to verify that the print head is clean (see the previous
section for details).
7. If there are still gaps or lines, or the test patterns are faint,
run another cleaning cycle and check the nozzles again.
Cancel/Back
12:00 PM Y
Setup button. You
4key on the numeric
Start Color/OK button. The CX7000F Series
1.Load/Eject
4.Head Cleaning
Cleaning
4.Head Cleaning, run a nozzle
Note:
If you don’t see any improvement after cleaning the print head four
times, turn off the CX7000F Series and wait at least six hours. This
lets any dried ink soften. Then try cleaning the print head again. If
quality still does not improve, one of the ink cartridges may be old or
damaged and needs to be replaced.
Tip:
If you do not use your CX7000F Series often, it is a good idea to
print a few pages at least once a month to maintain good print
quality.
Checking the Ink Status
You can check the status of ink in your cartridges using the
control panel.
1. Press the P
On button to turn
on the CX7000F Series, or
press the y
button until you see a screen
like this:
2. Press the
see this display:
Cancel/Back
Setup button. You
12:00 PM Y
1.Load/Eject
3. Press the u or d button, or
press the
keypad, to display this option:
4. Press the x
button. You see a display like
2key on the numeric
Start Color/OK
2.Ink Levels
C:50% M:50% Y:50
this:
5. If one or more cartridges are
low on ink, you see a display
C:Ink low M:50%
like this:
6. Press the x
Start Color/OK or y Cancel/Back button to
return to the screen displaying the date.
If you need to replace an ink cartridge, see the next section.
Note:
You can also check the ink status using software when the CX7000F
Series is connected to your computer (see the User’s Guide for
instructions).
Replacing Ink Cartridges
If you see a message like this on
the display, one or more cartridges
are low on ink:
When you see a message like this
on the display, you need to replace
one or more cartridges:
You cannot print when a cartridge
is expended.
C:Ink low M:50%
Replace Cyan ink
10/0615
Page 16
Epson Stylus CX7000F Series
Note:
You’ll also see a low ink or cartridge replacement message on your
computer screen when you print from your computer.
If a cartridge is more than six months old, print quality may decline. If
necessary, try cleaning the print head (see page 15). If printouts still
do not look their best, you may need to replace the cartridge.
Removing and Installing Ink Cartridges
Note:
Leave the expended cartridge installed until you have obtained a
replacement or the ink remaining in the print head nozzles may dry
out.
Make sure you have a new ink cartridge before you begin. Once you
start replacing a cartridge, you must complete all the steps in one
session.
Do not open ink cartridge packages until you are ready to install the
ink. Cartridges are vacuum packed to maintain reliability.
If you remove a cartridge that is low (for which you have received an
“Ink low” message), you cannot reuse it.
1. Press the P On button to turn
on the CX7000F Series, or
press the y
button until you see a screen
like this:
2. Press the
see this display:
3. Press the u or d button, or
press the
keypad, to display this option:
4.
Press the x Start Color/OK button.
5. Make sure that the document cover is closed, then open the
scanner.
Cancel/Back
Setup button. You
5key on the numeric
12:00 PM Y
1.Load/Eject
5.Replace Cartri
6. Open the cartridge cover.
7. Squeeze the tab at the back of the cartridge and lift it
straight out. Dispose of it carefully. Do not take the used
cartridge apart or try to refill it.
Warning:
If ink gets on your hands, wash them thoroughly with soap and
water. If ink gets into your eyes, flush them immediately with
water.
8. Before you open the new ink cartridge package, shake it
four or five times. Then remove it from the package.
Caution:
Do not open the scanner when the document cover is open.
Do not move the print head by hand; this may damage the
CX7000F Series. Always select 5.Replace Cartridge from the
display to move it.
Never attempt to open the cartridge cover when the print head is
moving. Wait until the cartridges have moved to the replacement
position.
1610/06
Caution:
Do not touch the green chip on the front of the cartridge. This can
damage the ink cartridge.
9. Remove the yellow tape from the bottom of the ink
cartridge.
Page 17
Epson Stylus CX7000F Series
Start
Color
OK
Caution:
If you do not remove the yellow tape before installing the ink
cartridge, print quality may decline or you may not be able to
print.
Do not remove any other seals from the cartridges.
.
10. Place the new ink cartridge into the cartridge holder and
push it down until it clicks into place.
11. Replace any other cartridges that need to be replaced.
12. Close the ink cartridge cover and press it until it clicks into
place.
14. Press the x
begins charging ink and
Start Color/OK button. The CX7000F Series
Chargingappears on the display.
Charging takes about one minute. When it’s finished,
5.Replace Cartridge appears on the display.
Caution:
Never turn off the CX7000F Series while Charging appears on
the display or you’ll waste ink.
Note:
If you see an ink cartridge error message on the display, the ink
cartridge may not be installed correctly. Press the
OK button and reinstall the ink cartridge until it clicks into place.
x Start Color/
15. Press the y Cancel/Back button until you return to the
screen displaying the date.
Caution:
If you replaced a cartridge while copying a photo or document,
cancel printing and make sure your original is still placed correctly
on the document table. Then copy your original again.
13. Close the scanner.
Aligning the Print Head
If your printouts look grainy or blurry, or you see light or dark
horizontal banding, you may need to align the print head.
Note:
Banding may also occur if your cartridges are low on ink or you need
to clean the print head.
1. Turn on the CX7000F Series.
2. Load several sheets of paper.
3. Windows: Right-click the printer icon on your taskbar
(in the lower right corner of your screen). Select
Alignment.
Macintosh OS X: Open the Applications folder and select
EPSON Print Utility. Select your CX7000F Series in the
printer list, click
OK, and select Print Head Alignment.
Print Head
10/0617
Page 18
Epson Stylus CX7000F Series
4. Follow the instructions on the screen to print a vertical
alignment sheet. You see a window like this one:
5. Look at the five sets of patterns in your printout. For each
set, if you see a pattern with no visible vertical lines, enter its
number in the corresponding box on the screen and click
Next.
If you can’t find an aligned pattern, choose the one that’s
closest to being aligned. Click
Realignment and then Print
to print another alignment sheet and repeat this step.
6. Click
Print to print a black horizontal alignment sheet.
After it’s printed, you see a window like this one:
8. Click
Printto print a color horizontal alignment sheet.
After it’s printed, you see a window like this one:
9. Look at the printout and find the pattern with no gap or
line between the rectangles and enter its number in the box
on the screen.
10. If you can’t find an aligned pattern, choose the one that
looks the best. Then click
Realignment to print another
alignment sheet and repeat this step.
11. Click
Finishto close the Print Head Alignment Utility.
Transporting the CX7000F Series
7. Look at the printout and select the pattern with no gap or
line between the rectangles. Enter the number for that
pattern in the box on the screen and click
Next.
If you can’t find an aligned pattern, choose the one that
looks the best. Then click
Realignment to print another
alignment sheet and repeat this step.
If you need to ship your CX7000F Series, you must prepare it
for transportation by packing it in its original box or one of a
similar size.
1. Turn off the CX7000F Series.
2. Remove any paper from the sheet feeder and close the paper
support.
3. Unplug the power cord from the electrical outlet. Then
disconnect the USB cable from the CX7000F Series.
4. Open the scanner section and make sure the ink cartridge
holder is in the home position on the right.
5. Secure the ink cartridge holder (print head) to the case with
tape.
Caution:
Before you turn on the CX7000F Series, be sure to remove the
tape after installing the printer in its new location.
1810/06
Page 19
Epson Stylus CX7000F Series
6. Close the scanner section, push in the output tray extension,
and close the output tray.
7. Repack the CX7000F Series in the original box using the
protective materials that came with it.
Keep the CX7000F Series level as you transport it.
After transporting the CX7000F Series, remove the tape
securing the print head, plug in the CX7000F Series, and turn
it on. If you notice a decline in print quality, clean the print
head (see page 15); if output is misaligned, align the print
head (see page 17).
Error Messages
Display messageCause and solution
Paper out -> Load paper
into the sheet feeder,
then press the OK
button.
Paper jam -> Press the
OK button. Remove any
remaining jammed paper
by hand.
[C, M, Y, B]: Ink low ->
Press the OK button to
begin ink cartridge
replacement.
Replace [Cyan, Magenta,
Yellow, Black] ink
cartridge -> Press the OK
button to begin ink
cartridge replacement.
No [Cyan, Magenta,
Yellow, Black] ink
cartridge -> Press the OK
button to install a new ink
cartridge.
[Cyan, Magenta, Yellow,
Black] Ink cartridge error > Cartridge replacement
is necessary. Press the
OK button to begin.
No memory cardA memory card is inserted that is not
No photos on memory
card
No index sheet detected
or sheet placed
incorrectly. Correct the
sheet placement and try
again.
No photos selected or
photos marked
incorrectly. Select photos
correctly and try again.
Load or reload paper in the sheet feeder
and press the
continue (see page 4 for details).
Press the
Remove any remaining jammed paper by
hand.
Ink is low in one or more of the indicated
cartridges (see page 15 for replacement
instructions).
Ink is expended in one or more of the
indicated cartridges (see page 15 for
replacement instructions).
An ink cartridge is not installed or is
installed incorrectly (see page 15 for
replacement instructions).
An ink cartridge that is not supported by
the CX7000F Series is installed (see
page 15 for replacement instructions).
supported by the CX7000F Series. Remove
the incompatible memory card and insert a
compatible card (see page 3 for details).
The inserted memory card does not
contain any valid images (see page 3 for a
list of compatible card and image types).
An index sheet was not recognized
because it is not positioned correctly. Align
the top of the sheet with the left edge of
the glass (see page 8 for details).
No marks are detected on the index sheet
or the sheet includes more than one mark
for an image. Remove the index sheet,
mark it correctly, and try again (see page 8
for details).
x Start Color/OK button to
x Start Color/OK button.
Display messageCause and solution
Memory card data does
not match index sheet.
Replace the card or index
sheet and try again.
Fax not sent. Resend
using the Start B&W
button.
Paper thickness lever is
set for envelope printing.
The index sheet does not match the
photos on the memory card. Remove the
card and insert the one used to print the
index sheet (see page 7), or place the
correct index sheet on the glass (see
page 8).
You sent a fax using the
OK button to a fax machine that prints only
in black and white. Send the fax again (see
page 12), but press the
button.
The paper thickness lever is set to the
x Start Color/
x Start B&W
^ H position. If you are printing on
envelopes, press
x Start Color/OK or
x Start B&W to continue. Otherwise, set
m L position.
x Start Color/OK or
Paper thickness lever is
set for printing sheets of
paper.
the lever to the
The paper thickness lever is set to the
m L position. If you are printing on paper
sheets, press
x Start B&W to continue. If you’re
printing on envelopes, set the lever to the
^ H position.
Service required. See
your documentation for
details.
Printer error -> or
Scanner error ->
See your documentation
and call service if
necessary.
A CX7000F Series part needs to be
replaced. Contact your local authorized
servicer or contact Epson for a referral.
There is a problem with the CX7000F
Series. Turn it off and then back on. If the
error does not clear, contact your local
authorized servicer or contact Epson for a
referral.
Related Documentation
CPD-22471Epson Stylus CX7000F Series
Start Here sheet
CPD-22473Epson Stylus CX7000F Series
Basics Guide
CPD-22472Epson Stylus CX7000F Series
CD-ROM
(includes on-screen User’s Guide)
10/0619
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.