Epson SRP-275 User Manual
User's Manual
SRP-275
Impact Printer
Rev. 1.03
http://www.samsungminiprinters.com
SRP-275
■ Safety Precautions
In using the present appliance, please keep the following safety regulations in order to
prevent any hazard or material damage.
WARNING
Violating following instructions can cause serious injury or death.
Do not plug several products in one multi-outlet.
• This can provoke over-heating and a fire.
• If the plug is wet or dirty, dry or wipe it before usage.
• If the plug does not fit perfectly with the outlet, do not plug in.
• Be sure to use only standardized multi-outlets.
PROHIBIT
Do not pull the cable to unplug.
• This can damage the cable, which is the origin of a fire or a
breakdown of the printer.
PROHIBIT
You must use only the supplied adapter.
• It is dangerous to use other adapters.
ONLY SUPPLIED ADAPTER
PROHIBIT
Keep the plastic bag out of children’s reach.
• If not, a child may put the bag on his head.
PROHIBIT
Do not plug in or unplug with your hands wet.
• You can be electrocuted.
PROHIBIT
Rev. 1.03
Do not bend the cable by force or leave it under any
heavy object.
• A damaged cable can cause a fire.
PROHIBIT
- 2 -
SRP-275
CAUTION
Violating following instructions can cause slight wound or damage the appliance
.
If you observe a strange smoke, odor or noise from
the printer, unplug it before taking following
measures.
• Switch off the printer and unplug the set from the mains.
• After the disappearance of the smoke, call your dealer to
repair it.
TO UNPLUG
PRINTER
Install the printer on the stable surface.
• If the printer falls down, it can be broken and you can hurt
yourself.
PRINTER
PROHIBIT
Keep the desiccant out of children’s reach.
• If not, they may eat it.
PROHIBIT
Use only approved accessories and do not try to
disassemble, repair or remodel it for yourself.
• Call your dealer when you need these services.
• Do not touch the blade of auto cutter.
DISASSEMBLING
PROHIBITED
PRINTER
Do not let water or other foreign objects in the
printer.
• If this happened, switch off and unplug the printer before
calling your dealer.
PROHIBIT
PRINTER
Rev. 1.03
Do not use the printer when it is out of order. This
can cause a fire or an electrocution.
• Switch off and unplug the printer before calling your dealer.
TO UNPLUG
PRINTER
DEALER
- 3 -
SRP-275
All rights reserved. No part of this publication may reproduced, stored in a retrieval, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording,
or otherwise, without the prior written permission of BIXOLON.
No patent liability is assumed with respect to the use of the information contained herein.
While every precaution has been taken in the preparation of this book, BIXOLON assumed
no responsibility for errors or omissions. Neither is any liability assumed for damages
resulting from the use of the information contained herein.
Neither BIXOLON nor its affiliates shall be liable to the purchaser of this product or third
parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a
result of : accident, misuse, or abuse of this product or unauthorized modifications, repairs,
or alterations to this product, or (excluding the U.S.) failure to strictly comply with
BIXOLON s operating and maintenance instructions.
BIXOLON shall not be liable against any damages or problems arising from the use of any
options or ant consumable products other than those designated as Original Samsung
products or Samsung Approved products by BIXOLON.
■ Notice
The contents of this manual are subject to change without notice.
Copyright© 2005 BIXOLON CO., LTD
Rev. 1.03
- 4 -
SRP-275
■ EMC and Safety standards Applied
Product Name : SRP-275
The following standards are applied only to the printers that are so labeled.
Europe : CE marking, TUV/GS : EN60950-1; 2001
North America : EMI : FCC Class A
Safety standards : UL / C-UL : UL60950-1
National : CB-scheme : IEC 60950-1: 2001
■ WARNING
The connection of a non-shielded printer interface cable to this printer will invalidate the
EMC standards of this device. You are cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void your authority to
operate the equipment.
■ CE Marking
The printer conforms to the following Directive and Norms
EMC Directive 89/336/EEC EN55022 Class A : 1998+A1 : 2000
EN55024 : 1998:+A1 : 2001
EN61000-3-2 : 2000
EN61000-3-3 : 1995+A1 : 2001
Low Voltage Directive 73/23/EEC Safety : EN60950-1 : 2001
■ Waste Electrical and Electric Equipment (WEEE)
This marking shown on the product or its literature, indicates that is should not
be disposed with other household wastes at the end of its working life, To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally
safe recycling. Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with other
commercial wastes for disposal.
■ Label Material
* Control Label: PC
* Other Labels: PET
Rev. 1.03
- 5 -
SRP-275
■ Introduction
The SRP-275 is a high-quality impact printer.
This one-station printer has the following features.
Compact design and light-weight.
•
• High-speed printing using logic-seeking (5.1LPS).
• Easy to use : Easy paper loading.
• High reliability and long life due to the use of stepping motors for head carriage return
and paper feeding.
• Two color printing (red/black) available.
• Various formats are possible because the paper feeding pitch is selectable.
• High general control utility based on the ESC/POS(TM) standard.
• The head can be driven due to the internal drawer interface.
• Character font (7ⅹ9, 9ⅹ9) is selectable.
• The auto cutter uses a circular method with a high-quality blade and a long life
(Approximately 1,000,000 cuts).
• Paper near end Switch is standard.
• A internal AC adaptor.
• Front view • Rear view
Rear cover
Front cover
Control panel
Open button
Drawer kick-out
connect
DIP Switch cover
Power connect
Interface
connector
Power switch
NOTES
Please be sure to read the instructions in this manual carefully before using your new printer.
Rev. 1.03
- 6 -
SRP-275
■ Table of Contents
1. Setting Up the Printer·······································································································8
1-1 Unpacking···················································································································8
1-2 Choosing a place for the printer··················································································8
1-3 Using the operation panel···························································································9
2. Connecting the cables ···································································································10
2-1 Connecting the AC Adaptor·······················································································10
2-2 Connecting the Interface cable and Drawer kick-out cable·······································10
2-2-1 Serial Interface (RS-232C)············································································11
2-2-2 Parallel Interface (IEEE1284)········································································12
2-2-3 USB Interface································································································13
2-2-4 Ethernet Interface ·························································································13
2-2-5 Drawer kick-out ·····························································································13
3. Setting the Switches ······································································································14
3-1 Setting the DIP Switch ······························································································14
3-1-1 DIP Switch setting for Epson(ESC/POS) mode ············································14
3-1-2 DIP Switch setting for Citizen(iDP 3550) mode·············································15
3-1-3 DIP Switch setting for Star(SP500) mode ·····················································16
3-1-4 Changing the DIP Switch setting···································································17
3-2 Setting the Memory Switches ···················································································18
3-2-1 Memory Switch setting for Epson(ESC/POS) mode ·····································18
3-2-2 Memory Switch setting for Star mode ···························································22
4. Ribbon Cassette Installation ··························································································28
5. Roll Paper Installation····································································································29
6. Changing the paper width······························································································30
7. Installing the wall mount (Option)···················································································31
8. Self Test ·························································································································32
9. Hexadecimal Dumping···································································································33
10. Specification·················································································································34
10-1 Printing specification·······························································································34
10-2 Paper specifications································································································34
10-3 Ribbon cassette specification ·················································································34
10-4 Electrical characteristics ·························································································35
10-5 Reliability ················································································································35
10-6 Environment conditions···························································································35
10-7 Dimensions & weight ······························································································36
10-8 Optional features ····································································································36
11. Appendix - Troubleshooting··························································································37
11-1 ERROR LED blinking pattern··················································································37
11-2 The printer does not start printing ···········································································38
11-3 The printer stops printing ························································································39
11-4 You want to check the operation of the printer by itself ···········································39
11-5 Printing is poor ········································································································39
Rev. 1.03
- 7 -
1. Setting Up the Printer
1-1 Unpacking
Your printer box should include the items shown in the illustration below.
If any items are damaged or missing, please contact your dealer.
SRP-275
SRP-275A, C AC adaptor Power cord
Ribbon cassette Paper roll Manual CD
1-2 Choosing a place for the printer
• Avoid locations that are subject to direct sunlight or excessive heat.
• Avoid using or storing the printer in a place subject to excessive temperature or moisture.
• Do not use or store the printer in a dirty location.
• When setting up the printer, choose a stable, horizontal location.
• Intense vibration or shock may damage the printer.
• Ensure the printer has enough space to be used easily.
Rev. 1.03
- 8 -
SRP-275
1-3 Using the operation panel
Most of the functions of this printer are governed by software, but you can monitor the printer s status by
looking at the lights on the control panel and for some procedures you will use the buttons.
• Control panel
- POWER LED (Green Color)
This indicator light is on when the power is turned on. It blinks when the printer is in the self
test printing standby state. Always wait until this indicator light stops blinking before you
start using the printer and before you turn it off.
- ERROR LED (Red Color)
When this indicator light is on (but not blinking), it means that the printer is out of paper or
almost out of paper or the printer covers are open. When this light blinking, there is an
error. (See "ERROR LED blinking pattern" in Chapter 11.) If you see this light blinking, turn
off the printer for a few seconds and then turn it back on. If the light is still blinking, call your
supervisor or a service person.
- PAPER OUT LED (Red Color)
When this indicator light is on, it means that the paper near end. Replace the new paper
roll. When ERROR and PAPER OUT indicator lights are on it means paper end. Install the
paper roll.(See "Installing paper roll" in Chapter 5.)
- FEED button
Rev. 1.03
Use this button to feed paper or to start self test and for hexadecimal dump mode.
(See the instructions "Self test" (8) in this chapter for self test.)
(See the instructions "Hexadecimal dump" in Chapter 9 for hexadecimal dump mode.)
- 9 -
2. Connecting the cables
2-1 Connecting the AC Adaptor
SRP-275
AC adaptor
• Connect the AC adapter according to the
following procedure.
Power connector
1) Make sure the printer is turned off.
2) Before inserting the AC adaptor, connect the
Power cord
power cord.
3) Insert the AC adaptor as shown.
4) Plug the AC adapter cable into the printer’s
power connector.
5) Plug the power cord into the outlet, and turn on
the power.
CAUTION
Before connecting the printer to the power supply, make sure that the voltage and power specifications
match the printer’s requirements. Using an incorrect power supply can cause serious damage to the printer.
2-2 Connecting the Interface cable and Drawer kick-out cable
• Connect the cables according to the
following procedure.
Drawer kick-out connector
Interface
connector
1) Turn off printer and the host ECR (host
computer).
2) Plug the interface cable into the interface
connector on the printer then fasten the screw
Drawer kick-out
cable
Serial/ Parallel/ USB/ Ethernet
Interface cable
on both sides of the connector.
3) Plug the drawer kick-out cable into the drawer
kick-out connector on the printer.
(When removing the drawer kick-out cable,
press on the connector’s clip while pulling out.)
NOTES
Connect the printer to the host ECR (host computer) though an interface cable matching the specification of
the printer and the host ECR (host computer). Be sure to use a drawer that matches the printer’s
specification.
Depending on the interface your system uses, either connect the serial, parallel, USB or Ethernet
communication cable to the appropriate connector on the back of the printer. Cables are provided by your
dealer or system installer.
Rev. 1.03
- 10 -
2-2-1 Serial Interface (RS-232C)
SRP-275
IFC-S TYPE
Interface connector
Drawer kick-out
Connector
(F.G) 1
(TXD) 2
(RXD) 3
PRINTER
SIDE
(25Pin)
(RTS) 4
(CTS) 5
(DSR) 6
(S.G) 7
(DTR) 20
Pin No. Signal name Direction Function
1 FG - Frame Ground
2 TxD Output Transmit Data
3 RxD Input Receive Data
6 DSR Input Data Set Ready
7 SG - Signal Ground
20 DTR Output Data Terminal Ready
1 (F.G)
2 (RXD)
3 (TXD)
4 (DTR)
5 (S.G)
6 (DSR)
7 (RTS)
8 (CTS)
HOST
SIDE
(9Pin)
Rev. 1.03
- 11 -
2-2-2 Parallel Interface (IEEE1284)
SRP-275
IFC-P TYPE
Interface connector
Drawer kick-out
Connector
Pin no. Source Compatibility mode Nibble mode Byte mode
1 Host nStrobe HostClk HostClk
2 Host / Printer Data 0 (LSB) - Data 0 (LSB)
3 Host / Printer Data 1 - Data 1
4 Host / Printer Data 2 - Data 2
5 Host / Printer Data 3 - Data 3
6 Host / Printer Data 4 - Data 4
7 Host / Printer Data 5 - Data 5
8 Host / Printer Data 6 - Data 6
9 Host / Printer Data 7 (MSB) - Data 7 (MSB)
10 Printer nAck PtrClk PtrClk
11 Printer Busy PtrBusy / Data3,7 PtrBusy
12 Printer Perror AckDataReq / Data2,6 AckDataReq
13 Printer Select Xflag / Data1,5 Xflag
14 Host nAutoFd HostBusy HostBusy
15 - NC ND ND
16 - GND GND GND
17 - GND FG FG
18 Printer Logic-H Logic-H Logic-H
19~30 - GND GND GND
31 Host nInit nInit nInit
32 Printer nFault nDataAbail / nDataAvail
33 - NC ND ND
34 Printer NC ND ND
35 Printer NC ND ND
36 Host nSelectln 1284-Active 1284-Active
Rev. 1.03
- 12 -
Loading...