WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.
Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and
filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically
explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service
personnel.
WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small
children to avoid any risk of suffocation.
Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by
the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. The information contained herein is designed only for use with
this Epson product. Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of
this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or
any consumable products other than those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.
Software Copyright:
This product uses free software as well as software to which this company holds the rights.
The following is information on the free software used by this product.
Hereafter, each author, the conditions, and so on are described in the original. Furthermore, there is no guarantee
for free software because of the characteristics of the free software that has already been used in this product; any
problems in this product (including problems that originate with the free software concerned) do not influence the
conditions of the guarantee (written guarantee) issued by this company.
Epson and Instant Off are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko
Epson Corporation.
PowerLite and PrivateLine are registered trademarks, SizeWise is a trademark, and Extra Care is a service mark of
Epson America, Inc.
Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing, LLC.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
theater-quality images in the relaxing environment of your own home.
You can connect it to a wide range of video sources and computers, so
you can enjoy perfectly adjusted images from all your movies and
games.
Your compact, lightweight projector offers these outstanding features:
■720p High-Definition performance
■Native WXGA resolution (1280 × 800) with up to 2000 lumens
of White and Color Light Output (brightness)
■HDMI
superior, uncompressed digital video
■SD
™
™
card slot and USB thumb drive port for PC-free slideshows
®
Home Cinema 700 lets you enjoy High-Definition,
(High Definition Multimedia Interface™) port for
■Seven color modes to optimize viewing for different environments
and image content
■Flexible setup options, including front projection and ceiling
mounted
■USB port for easy projection from a Windows
■Instant Off
■Auto Keystone correction and 1.2X optical zoom for easy picture
adjustments
■Password protection, projector button lock, and security cable
attachments for parental control and security
■Integral lens cover that won’t get lost
■Low power, long-lasting lamp with High and Low Brightness
modes
®
/On power modes for quick setup and take-down
®
computer
9
Using Your Documentation
This book contains all the information you need to set up and use
your projector. Please follow these guidelines as you read through it:
■Warnings must be followed carefully to avoid bodily injury.
■Cautions must be observed to avoid damage to your equipment.
■Notes contain important information about your projector.
■Tips contain additional projection hints.
Here’s where you can look for even more information:
■Quick Setup sheet
Provides information for connecting the projector to your
equipment, displaying and adjusting the image, and solving
display problems.
■Built-in help system
Provides assistance for common problems. Available from the
?Help button on the projector or the remote control. See page 82
for details.
■epson.com/support
Download FAQs and e-mail your questions to Epson support.
■PrivateLine
If you still need help after checking this User’s Guide and the
sources listed in this section, you can use the Epson PrivateLine
Support service to get help fast. Call (800) 637-7661 and enter
the PIN on the PrivateLine card. Or take advantage of Epson’s
automated support services 24 hours a day. See page 92 for more
information.
®
support
10Welcome
Projector Parts
Control panel
Kensington
lock port
Lens cover
Focus and
Zoom rings
Infrared
receiver
Adjustable
foot
SD card
slot
USB (TypeA)
port
Ventilation slotsAdjustable foot and
release lever
USB (TypeB)
port
Video
port
S-Video
port
Audio
ports
Computer
(Component
Video) port
AC power
inlet
Infrared
receiver
HDMI
port
Lamp
cover
Welcome11
Mounting bracket holes
(M4×9 screws required)
Projector Control Panel
Air filter
Security
cable slot
12Welcome
Source Search button
(searches for connected
video sources)
Power light
and button
Lamp and
Temperature
warning
lights
Volume
down
button
Menu button
(displays
projector menus)
Keystone
buttons
(correct screen
shape)
Esc button
(exits menu
items)
Volume up
button
Enter button
(selects
menu items)
Help
button
Remote Control Map
A/V Mute button
(turns off image)
Auto button
(resets tracking,
sync, and position)
Aspect button
(changes screen size)
Page Up/Down buttons
(control PowerPoint
USB cable required)
E-Zoom +/– buttons
(zoom into image)
Menu button
(accesses menus)
®
slides;
Power
button
Search and Source buttons
(select image source)
Freeze button
(stops image)
Color Mode button
(changes display mode)
Num button
(activates number
buttons)
Help button
(displays help menus)
Volume buttons
(adjusts volume)
Esc button
(exits menus)
Menu navigation buttons
and Enter button
Welcome13
3.73 in.
(94.7 mm)
0.26 in.
(6.7 mm)
Projector Dimensions
Use the dimensions below to guide you in placing or installing the
projector.
Center of lens
1.95 in.
(49.6 mm);
center of lens
3.21 in.
(81.5 mm)
to mounting
bracket holes
3.64 in.
(92.5 mm)
3.62 in.
(92 mm)
0.47 in.
(12 mm)
4.53 in.
(115 mm)
12.87 in.
(327 mm)
5 in.
(127 mm)
9.65 in.
(245 mm)
2.66 in.
(67.5 mm)
14Welcome
Registration and Warranty
Your projector comes with a basic warranty that lets you project with
confidence. For details, see the warranty brochure included with your
projector.
In addition, Epson offers free Extra Care
SM
Home Service. In the
unlikely event of an equipment failure, you won’t have to wait for
your unit to be repaired. Instead, Epson will ship you a replacement
unit anywhere in the United States or Canada, usually via overnight
delivery. See the brochure included with your projector for details.
To register, simply fill out the registration card and mail it to Epson.
Or you can register online at epson.com/webreg
. Registering also lets
you receive special updates on new accessories, products, and service.
Optional Accessories
To enhance your use of the projector, Epson offers the following
optional accessories:
ProductPart number
Replacement lampV13H010L41
Replacement air filterV13H134A13
Universal projector ceiling mount
Advanced projector ceiling mount with precision gear
High security projector ceiling mount
Adjustable suspended ceiling channel kit
False ceiling plate kit
Structural round ceiling plate
Adjustable extension column (pipe) 8” - 11”
Image presentation camera (ELPDC05)
DC-10s document camera
Soft carrying case (projector only)
Soft shoulder case for projector and notebook
Wheeled soft carrying case
Molded hard-shell wheeled carrying case
Swiss Gear
®
backpack
V12H162020
ELPDC10S
V12H00160
ELPKS61
ELPKS62
ELPKS58
ELPKS63
You can purchase screens or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com
(U.S. sales) or www.epson.ca
(Canadian sales).
16Welcome
1
1
Setting Up the Projector
This chapter tells you how to unpack the projector and connect it to
video equipment, such as a VCR, DVD player, or video camera,
and/or to a notebook or desktop computer.
You can also connect the projector to a USB storage device or digital
camera, or project from an inserted SD card.
Follow the instructions in this chapter on:
■Unpacking the projector
■Positioning the projector
■Connecting to a computer
■Connecting to video equipment
■Playing sound through the projector
■Connecting to a digital camera or other USB device
■Inserting an SD card
■Turning the projector on and off
17
Unpacking the Projector
After unpacking the projector, make sure you have all these parts:
PDF manual and
registration CD-ROM
Projector
Component-to-VGA
video adapter
Power cord
Remote control
and batteries
Save all packaging in case you need to ship the projector. Always use
the original packaging (or the equivalent) when you need to send the
projector to another location; see page 79 for instructions.
Additional Components
Depending on how you plan to use the projector, you may need
additional components:
■To receive an HDMI signal from your video device, you’ll need
an HDMI cable. One may be provided with your video
equipment.
■To receive a component video signal from a DVD player or other
video device, you’ll need a component video cable (one may be
provided with your video equipment) and the
component-to-VGA video adapter that came with the projector.
■To receive an S-Video signal, you’ll need an S-Video cable. One
may be included with your video equipment, or you can purchase
one from Epson. See “Optional Accessories” on page 15.
18Setting Up the Projector
■To receive an audio signal, you’ll need an RCA-type audio cable
with two male plugs, or a stereo mini-jack audio adapter cable
(not necessary with HDMI connection).
Positioning the Projector
You can place the projector in a variety of viewing setups.
When projecting from the front, place the projector directly in front
of the center of the screen, facing the screen squarely. The center of
the lens should be about level with the bottom of the screen.
If you place the projector below screen level, you may need to tilt it up
by extending the front adjustable foot (see page 41). Tilting the
projector causes the image to become “keystone” shaped, but you can
correct the distortion (see page 41).
note
After positioning the
projector, you may want to
connect a Kensington
MicroSaver
device to the lock port on the
projector. You can purchase
this from Epson; see
page 15.
®
anti-theft
You can also install the projector on the ceiling using the optional
ceiling mounting hardware (see page 15). Use the projector
dimensions on page 14 to assist you in installing the projector.
Setting Up the Projector19
You can also install the projector in two other viewing setups: rear
projection onto a semi-transparent screen, or rear/ceiling projection.
If you project from overhead or the rear of the screen, you’ll need to
select the appropriate
Projection setting in the projector’s Extended
menu to orient the image correctly (see page 62).
Keep these considerations in mind as you position the projector:
■Place the projector on a sturdy, level surface.
■Make sure there is plenty of space for ventilation around and
under the projector.
■Make sure the projector is within 5.9 feet (1.8 meters) of a
grounded electrical outlet or extension cord.
Determining Projection Distance
Image size increases with distance, but can vary depending on the
aspect ratio (image shape), how you zoom into the image, and
whether you’ve adjusted other image settings. Use the illustrations and
tables below to help you determine the projection distance.
20Setting Up the Projector
Center of lens
16:10 image
Diagonal screen
size
27 inches
(69 cm)
30 inches
(76 cm)
40 inches
(102 cm)
Center of
lens
Projection distance (A)
Wide to Tele
33 to 40 inches
(84 to 101 cm)
37 to 45 inches
(94 to 113 cm)
50 to 60 inches
(126 to 152 cm)
16:10 image
Diagonal screen
size
50 inches
(127 cm)
60 inches
(152 cm)
80 inches
(203 cm)
100 inches
(254 cm)
150 inches
(381 cm)
200 inches
(508 cm)
250 inches
(635 cm)
4:3 image
Screen size
24 inches
(61 cm)
30 inches
(76 cm)
40 inches
(102 cm)
50 inches
(127 cm)
60 inches
(152 cm)
70 inches
(178 cm)
80 inches
(203 cm)
100 inches
(254 cm)
150 inches
(381 cm)
Projection distance (A)
Wide to Tele
62 to 75 inches
(158 to 191 cm)
75 to 90 inches
(191 to 230 cm)
101 to 121 inches
(255 to 307 cm)
126 to 152 inches
(320 to 385 cm)
190 to 228 inches
(482 to 579 cm)
253 to 305 inches
(644 to 774 cm)
317 to 381 inches
(806 to 968 cm)
Projection distance (A)
Wide to Tele
33 to 40 inches
(84 to 102 cm)
42 to 51 inches
(106 to 129 cm)
56 to 68 inches
(143 to 173 cm)
71 to 85 inches
(180 to 217 cm)
85 to 103 inches
(216 to 260 cm)
100 to 120 inches
(253 to 304 cm)
114 to 137 inches
(290 to 348 cm)
143 to 172 inches
(363 to 436 cm)
215 to 258 inches
(546 to 656 cm)
Setting Up the Projector21
4:3 image
Screen size
200 inches
(508 cm)
235 inches
(597 cm)
16:9 image
Screen size
27 inches
(69 cm)
30 inches
(76 cm)
40 inches
(102 cm)
50 inches
(127 cm)
60 inches
(152 cm)
70 inches
(178 cm)
80 inches
(203 cm)
100 inches
(254 cm)
150 inches
(381 cm)
200 inches
(508 cm)
260 inches
(660 cm)
Projection distance (A)
Wide to Tele
287 to 345 inches
(729 to 876 cm)
338 to 406 inches
(857 to 1030 cm)
Projection distance (A)
Wide to TeleOffset (B)
34 to 41 inches
(86 to 104 cm)
38 to 46 inches
(96 to 116 cm)
51 to 62 inches
(130 to 156 cm)
64 to 77 inches
(163 to 196 cm)
77 to 93 inches
(196 to 236 cm)
90 to 109 inches
(229 to 276 cm)
103 to 124 inches
(263 to 316 cm)
130 to 156 inches
(329 to 396 cm)
195 to 234 inches
(495 to 596 cm)
261 to 313 inches
(662 to 795 cm)
339 to 407 inches
(861 to 1035 cm)
0.7 inch
(2 cm)
0.8 inch
(2 cm)
1.1 inches
(3 cm)
1.4 inches
(3 cm)
1.6 inches
(4 cm)
1.9 inches
(5 cm)
2.2 inches
(6 cm)
2.7 inches
(7 cm)
4.1 inches
(10 cm)
5.5 inches
(14 cm)
7.1 inches
(18 cm)
22Setting Up the Projector
Connecting to Video Equipment
You can connect several video sources to the projector at the same
time. Before starting, look at your video equipment to determine its
available video output connections:
■If your video player has an HDMI connector, see “Connecting an
HDMI Video Source” on page 24.
■If your video player has a component video port (three connectors
labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a
Component Video Source” on page 25.
■If your video player has a yellow RCA video output connector, see
“Connecting a Composite Video Source” on page 26.
■If your video player has an S-Video connector, see “Connecting
an S-Video Source” on page 27.
■If your video player has an RGB video port, see “Connecting an
RGB Video Source” on page 28.
After connecting video cables, you may also want to connect an
optional audio cable to play sound through the projector; see page 32.
If you connect using an HDMI cable, the video and sound are both
transferred and you won’t need to connect any additional cables for
audio.
Setting Up the Projector23
note
p
f
If an HDMI cable was not
rovided with your video
device, you can purchase one
rom an electronics dealer.
Connecting an HDMI Video Source
For the best image and sound quality, connect your video equipment
to the HDMI (High-Definition Multimedia Interface) port, if
possible.
Connect an HDMI cable to the HDMI connector on your player and
the
HDMI port on the projector.
HDMI port
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
24Setting Up the Projector
Connecting a Component Video Source
If your video equipment has component video connectors (three
connectors labeled either Y/Cb/Cr or Y/Pb/Pr), you can use the
component-to-VGA video adapter that came with your projector and
a component video cable, or you can purchase a component-to-VGA
video cable from Epson (see page 15) or an electronics dealer.
1. Connect one end of your component video cable to the Y/Cb/Cr
(or Y/Pb/Pr) connectors on your player.
2. Connect the component end of the component-to-VGA video
adapter to the free end of the component video cable.
3. Connect the VGA end of the adapter to the
(Component Video)
Computer (Component Video) port
4. You may need to change the
projector’s Signal menu to
port on your projector.
Input Signal setting in the
Auto (see page 60).
Computer
5. If you want to play sound through the projector, see page 32 for
instructions on connecting an audio cable.
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
Setting Up the Projector25
note
p
f
If the video cable was not
rovided with your video
device, you can purchase one
rom an electronics dealer.
Connecting a Composite Video Source
1. If your video cable has an RCA connector, connect it to the
yellow video output connector on your player and the yellow
Video port on the projector.
Video port
2. If you want to play sound through the projector, see page 32 for
instructions on connecting an audio cable.
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
26Setting Up the Projector
Connecting an S-Video Source
p
f
1. Connect the S-Video cable to the S-Video connector on your
player and the
2. If you want to play sound through the projector, see page 32 for
instructions on connecting an audio cable.
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
S-Video port on the projector.
S-Video port
note
If the S-Video cable was not
rovided with your video
device, you can purchase one
rom Epson; see page 15.
Setting Up the Projector27
note
You can purchase a VGA
computer cable from an
electronics dealer.
Connecting an RGB Video Source
You can connect to an RGB video source using a VGA computer
cable.
1. Connect the cable to the RGB video port on your player and the
Computer (Component Video) port on the projector.
Computer (Component Video) port
2. You may need to change the
projector’s Signal menu to
Input Signal setting in the
RGB (see page 60).
3. If you want to play sound through the projector, see page 32 for
instructions on connecting audio cables.
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
28Setting Up the Projector
Connecting to a Computer
You can connect the projector to a Windows computer using the
projector’s
with you when you transport the projector.
You can also connect the projector to any computer that has a
standard video output (monitor) port, including desktop models,
PC notebook computers, Macintosh PowerBook
computers, and hand-held devices. See page 31 for instructions on
connecting using a VGA computer cable.
To play sound through the projector, connect an audio cable (see
page 32).
You may be able to use your remote control as a wireless mouse when
projecting from a computer (see page 48).
Connecting to the USB Port
You can connect a Windows Vista®, XP, or Windows 2000 (SP4)
computer to the projector’s
project your computer’s display. A USB 2.0 connection
(recommended) provides better picture quality and response than
USB 1.1.
TypeB USB port. This lets you carry a lightweight cable
®
and iBook®
TypeB (square) USB port and
The first time you connect a computer to the projector’s USB port,
software from the projector is installed on your computer.
1. Follow the instructions beginning on page 35 to turn on the
projector.
2. Make sure the
to
USB Display (see page 62).
3. Turn on your computer.
USB Type B setting on the Extended menu is set
Setting Up the Projector29
4. Connect the square end of a USB cable to the projector’s
TypeB
(square) USB port.
USB TypeB port
5. Connect the flat end of the cable to any available USB port on
your notebook or desktop computer.
Messages appear on your computer screen as the projector is
recognized and the software is installed automatically.
6. Follow the instructions on the screen to install the Epson USB
Display software. If you see a “Digital Signature Warning,” select
Continue or Continue Anyway. (You will see these instructions
only the first time you connect.)
30Setting Up the Projector
After the software is installed, you see your computer’s current
desktop displayed by the projector. You can switch the projector
to other image sources using the
Source Search or Search
button on the remote control or the projector.
7. You can connect an optional audio cable if you want to play
sound through the projector (see page 32).
When you’ve finished making connections, see Chapter 2 for
instructions on displaying and adjusting the image.
When you’re done projecting from your computer, disconnect the
USB cable.
Loading...
+ 80 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.