Epson ML 3320/3321, ML 3320, ML 3321 Owner's Manual

Page 1
English
QUIETPARKTEAR
TOF
PRINT QUALITY
CHARACTER PITCH
HSD
NLQ
UTL
SSD
10 12 15
17
20 PROP
Page 2
Oki and Microline are registered trademarks of Oki Electric Industry Company, Ltd.
Energy Star is a trademark of the United States Environmen­tal Protection Agency.
Epson is a registered trademark of Epson America, Inc. IBM is a registered trademark of International Business
Machines Corp.
Energy Star
As an Energy Star Partner, Oki has determined that this product meets the Energy Star guidelines for energy efficiency.
Page 3
English
iRead Me First
Do not use your printer near water, or spill liquid of any kind into it.
Be certain that your power source matches the rating listed on the back of the printer. If you are not sure, check with your dealer or with your local power company.
Your printer has an earthed, 3-pin plug as a safety feature, and it will only fit into an earthed outlet. If you can not plug it in, chances are that you have an older, non-earthed outlet; contact an electrician to have it replaced with an earthed outlet. Do not use an adapter to defeat the earthing.
The outlet into which you plug your printer must remain easily accessible at all times.
To avoid damaging the power cable, do not put anything on it or place it where it will be walked on. If the cable becomes damaged or frayed, replace it immediately.
If you are using an extension cable or power strip with the printer, make sure that the total of the amperes required by all the equipment on the extension is less than the extension’s rating. Generally, the total ratings of all equipment plugged into any one power line should not exceed 15 amperes. Don’t exceed this unless you know that the power line your equipment is plugged into has a rating above 15 amperes.
Page 4
Page 5
English
iiiRead Me First
Setting the Top of Form (TOF) ......................................... 9
Temporarily Changing the Top of Form Setting ............. 10
Resetting the Top of Form to the Standard Setting ......... 10
Switching Paper Paths ..................................................... 11
Setting the Printhead Gap................................................ 11
Running the Self Tests..................................................... 12
Font Sample Test ............................................................. 12
ASCII Test ....................................................................... 12
Selecting an Emulation.................................................... 12
Selecting a Printer Driver ................................................ 13
Printer Drivers ................................................................. 13
Index ................................................................................ 15
Page 6
Page 7
English
1Read Me First
Unpacking
QUIETPARKTEAR
FF/LOAD
LF
SEL
SEL
POWER ALARM
MENU
GROUPEXIT
ITEM SET
PRINT
MENU
SHIFT
TOF
Micro Feed
Up
Micro Feed Down
PRINT QUALITY
CHARACTER PITCH
HSD NLQ
UTL SSD
10 12 15 17
20 PROP
Printer ❷ Ribbon cartridge ❸ In-line filter
Ribbon cartridge missing? Contact your dealer.
Page 8
QUIETPARKTEAR
FF/LOAD
LF
SEL
SEL
POWER ALARM
MENU
GROUPEXIT
ITEM SET
PRINT
MENU
SHIFT
TOF
Micro Feed
Up
Micro Feed Down
PRINT QUALITY
CHARACTER PITCH
HSD NLQ
UTL SSD
10 12 15 17
20 PROP
Set up for Single-Sheet FeedSet up for Rear Feed of Continuous Forms
Carriage Cover Open
Access Cover
Paper Lever
Platen Knob
Paper Separator
Paper Guides
Paper Separator
On-Off Switch
Control Panel
On-Off Switch
Page 9
English
3Read Me First
Installing the Ribbon Cartridge
1. Make sure the printer is turned OFF.
2. Centre the printhead ().
M
Take-up knob
Grip points
Ribbon shield
3. Unpack the ribbon cartridge.
Page 10
Connecting to the Computer
Note: You must supply a shielded cable for connecting
your printer to your computer.
1. When using the parallel interface cable, it needs to be fitted with an in-line filter. If your cable does not have an in-line filter, one has been supplied for you in your accessory pack.
To fit, carefully open your in-line filter and close it over the parallel interface cable, as close to the printer end connector as possible, ensuring that the f ilter snaps closed.
2. Plug the interface cable into the parallel port () and secure it with the wire loops.
3. Attach the other end of the cable to your computer.
Page 11
English
5Read Me First
Loading Paper
Loading Continuous Forms (Rear Feed)
We recommend the rear-feed path for printing reports, etc., on single-thickness, continuous-form paper. For graphics or charts, it's best to use the single-sheet path (top feed).
Note: If you ha ve paper in the paper path, be sure to
remove it before installing rear-feed paper.
T ractor Terms
Pins
Tractor Cover
Lock Lever
Page 12
4. Move the right tractor over to fit the width of the paper.
Page 13
English
7Read Me First
7. Adjust the right tractor to centre the paper holes on the pins, and push back the lock lever.
8. Lower the paper separator and place the wire guide (➊) on the pull-up roller assembly ().
9. Press FF/LOAD. The paper feeds into the printer.
Note: The standard setting for the Top o f Form (where
the printing begins) is 2.54cm down from the top of the page. To change the setting, see page 9.
Page 14
QUIETPARKTEAR
FF/LOAD
LF
SEL
SEL
POWER ALARM
MENU
GROUPEXIT
ITEM SET
PRINT
MENU
SHIFT
TOF
Micro Feed Up
Micro Feed Down
PRINT QUALITY
CHARACTER PITCH
HSD NLQ
UTL SSD
10 12 15 17
20 PROP
QUIETPARKTEAR
FF/LOAD
LF
SEL
SEL
POWER ALARM
MENU
GROUPEXIT
ITEM SET
PRINT
MENU
SHIFT
TOF
Micro Feed Up
Micro Feed Down
PRINT QUALITY
CHARACTER PITCH
HSD
NLQ
UTL SSD
10 12 15 17
20 PROP
3. Open the carriage cover and lift the paper separator to the single-sheet position.
4. Make sure the wire feed guide ( ) is in the paper separator.
Page 15
English
9Read Me First
M
QUI
PARK
PRINT QUALITY
HSD
Setting the Top of Form (TOF)
When setting the Top of Form, use the red line () on the paper shield as a reference:
1. Make sure the printer is deselected (SEL light off).
2. Press and hold SHIFT (), then:
Press LF (➋) to move Top of Form higher on pagePress FF/LOAD (➌) to move Top of Form lower on
page
QUIETPARKTEAR
FF/LOAD
LF
SEL
SEL
POWER ALARM
MENU
GROUPEXIT
ITEM SET
PRINT
MENU
SHIFT TOF
Micro Feed
Up
Micro Feed
Down
➋➌
Page 16
Resetting the Top of Form to the Standard Setting
1. Turn the printer off.
2. Hold PARK + QUIET/TOF while turning the printer back on.
QUIETPARKTEAR
FF/LOAD
LF
SEL
SEL
POWER ALARM
MENU
GROUPEXIT
ITEM SET
PRINT
MENU
SHIFT TOF
Micro Feed
Up
Micro Feed
Down
Page 17
English
11Read Me First
Setting the Printhead Gap
The printhead gap is the distance between the printhead and the platen. T o adjust the gap , open the access cover and mo ve the blue lever () to the recommended setting from the table below.
Note: It is recommended that the printer be switched off
prior to removing the access cover.
Media Setting Media Setting 45-75g/m² paper 1 2-part form (w/carbon) 3-4
75-90g/m² bond paper 2 3-part form (w/carbon) 4 -5 Labels 3-4 4-part form (w/carbon) 5 Envelopes 5
Page 18
Selecting an Emulation
Your printer has three emulations:
Epson® FX
IBM® Proprinter III
MICROLINE® Standard
The printer comes set for the IBM Proprinter III emulation. To change to one of the other emulations:
1. Make sure paper is loaded.
2. Deselect the printer (SEL light off, press SEL key).
3. Press SHIFT + SEL: the printer will enter the Menu Mode.
QUIETPARKTEAR
FF/LOAD
LF
SEL
SEL
POWER ALARM
MENU
GROUPEXIT
ITEM SET
PRINT
MENU
SHIFT TOF
Micro Feed
Up
Micro Feed
Down
Page 19
English
13Read Me First
QUIETPARKTEAR
Selecting a Printer Driver
Before you can use your printer with softwa re, you must enter the software and select the correct printer driver. If you have the wrong driver selected, you will see strange characters, incorrect fonts, etc.
Important! See your software documentation for
information on how to select a printer driver .
Printer Drivers
The drivers belo w are listed by decr easing compatibility with your printer: use one as close to the top of the list as possible.
IBM Proprinter III Epson FX Microline Standard
ML3320/1 IBM ML3320/1 Epson Microline 320/321 IBM Proprinter III Epson FX286e Microline 320/321 IBM Proprinter II Epson FX 850/1050 Microline 320/321 IBM Proprinter Epson FX 86/286 Microline 292/293 IBM Graphics Printer Epson FX Microline 192/193
Epson FX800/1000 Microline 182/183
Page 20
Page 21
English
15Read Me First
L
Labels, head gap setting ................. 11
Loading paper ................................ 5-9
Lock lever ......................................... 5
M
Microline emulation .............. 1, 12-13
P
Paper
guides ........................................... 2
lever.............................................. 2
loading....................................... 5-9
paths, changing........................... 11
separator ....................................... 2
shield ............................................ 9
Parallel port connection .................... 4
Pins, tractor....................................... 5
Platen knob ....................................... 2
Power switch................................. 2, 5
Printer drivers ................................. 13
Printhead gap .................................. 11
Page 22
Page 23
English
17Read Me First
Loading...