EPSON G20-A04C, G10-654SR, G10-851S, G20-854C, G10-654C User Manual
...
G10 / G20 series
Rev.10 EM111R2122F
SCARA ROBOT
MANIPULATOR MANUAL
MANIPULATOR MANUAL G10 / G20 series Rev.10
SCARA ROBOT
G10 / G20 series Manipulator Manual
Rev.10
Copyright © 2007-2011 SEIKO EPSON CORPORATION. All rights reserved.
G10 / G20 Rev.10 i
d
FOREWORD
Thank you for purchasing our robot products.
This manual contains the information necessary for the correct use of the manipulator.
Please carefully read this manual and other related manuals before installing the robot
system.
Keep this manual handy for easy access at all times.
WARRANTY
The Manipulator and its optional parts are shipped to our customers only after being
subjected to the strictest quality controls, tests, and inspections to certify its compliance
with our high performance standards.
Product malfunctions resulting from normal handling or operation will be repaired free of
charge during the normal warranty period. (Please ask your Regional Sales Office for
warranty period information.)
However, customers will be charged for repairs in the following cases (even if they occur
during the warranty period):
1. Damage or malfunction caused by improper use which is not described in the manual,
2. Malfunctions caused by customers’ unauthorized disassembly.
3. Damage due to improper adjustments or unauthorized repair attempts.
or careless use.
4. Damage caused by natural disasters such as earthquake, flood, etc.
Warnings, Cautions, Usage:
1. If the Manipulator or associated equipment is used outside of the usage conditions an
product specifications described in the manuals, this warranty is void.
2. If you do not follow the WARNINGS and CAUTIONS in this manual, we cannot be
responsible for any malfunction or accident, even if the result is injury or death.
3. We cannot foresee all possible dangers and consequences. Therefore, this manual
cannot warn the user of all possible hazards.
ii G10 / G20 Rev.10
TRADEMARKS
Microsoft, Windows, and Windows logo are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries. Other brand and
product names are trademarks or registered trademarks of the respective holders.
NOTICE
No part of this manual may be copied or reproduced without authorization.
The contents of this manual are subject to change without notice.
Please notify us if you should find any errors in this manual or if you have any comments
regarding its contents.
INQUIRIES
Contact the following service center for robot repairs, inspections or adjustments.
If service center information is not indicated below, please contact the supplier office for
your region.
Please prepare the following items before you contact us.
- Your controller model and its serial number
- Your manipulator model and its serial number
- Software and its version in your robot system
- A description of the problem
SERVICE CENTER
G10 / G20 Rev.10 iii
MANUFACTURER & SUPPLIER
TEL : +81-(0)266-61-1802
FAX : +81-(0)266-61-1846
Japan & Others
SEIKO EPSON CORPORATION
Suwa Minami Plant
Factory Automation Systems Dept.
1010 Fujimi, Fujimi-machi,
Suwa-gun, Nagano, 399-0295
JAPAN
SUPPLIERS
Factory Automation/Robotics
TEL : +1-562-290-5900
FAX : +1-562-290-5999
E-MAIL : info@robots.epson.com
Factory Automation Division
TEL : +49-(0)-2159-538-1391
FAX : +49-(0)-2159-538-3170
E-MAIL : robot.infos@epson.de
Factory Automation Division
TEL : +86-(0)-10-8522-1199
FAX : +86-(0)-10-8522-1120
Taiwan
Factory Automation Division
TEL : +886-(0)-2-8786-6688
FAX : +886-(0)-2-8786-6677
North & South America
Europe
China
EPSON AMERICA, INC.
18300 Central Avenue
Carson, CA 90746
USA
EPSON DEUTSCHLAND GmbH
Otto-Hahn-Str.4
D-40670 Meerbusch
Germany
EPSON China Co., Ltd
7F, Jinbao Building No. 89 Jinbao Street
Dongcheng District, Beijing,
China, 100005
EPSON Taiwan Technology & Trading Ltd.
14F, No.7, Song Ren Road, Taipei 110
Taiwan, ROC
iv G10 / G20 Rev.10
For Customers in the European Union
The crossed out wheeled bin label that can be found on your product indicates that this
product and incorporated batteries should not be disposed of via the normal household
waste stream. To prevent possible harm to the environment or human health please
separate this product and its batteries from other waste streams to ensure that it can be
recycled in an environmentally sound manner. For more details on available collection
facilities please contact your local government office or the retailer where you purchased
this product. Use of the chemical symbols Pb, Cd or Hg indicates if these metals are used
in the battery.
This information only applies to customers in the European Union, according to
DIRECTIVE 2006/66/EC OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL OF 6 September 2006 on batteries and accumulators and waste batteries and
accumulators and repealing Directive 91/157/EEC and legislation transposing and
implementing it into the various national legal systems.
For other countries, please contact your local government to investigate the possibility of
recycling your product.
The battery removal/replacement procedure is described in the following manuals:
Controller manual / Manipulator manual (Maintenance section)
G10 / G20 Rev.10 v
Before Reading This Manual
This section describes what you should know before reading this manual.
Structure of Control System
The G10 / G20 series Manipulators can be used with the following combinations of
Controllers and software.
The operating methods and descriptions are different depending on which software you are
using. The following icons are put beside appropriate text as necessary. Use the
descriptions that pertain to the software you are using.
Controller Software
RC180 EPSON RC+ 5.0
RC620 EPSON RC+ 6.0
For details on commands, refer to User’s Guide or “On-line help”.
Turning ON/OFF Controller
When you see the instruction “Turn ON/OFF the Controller” in this manual, be sure to
turn ON/OFF all the hardware components. For the Controller composition, refer to the
table above.
Shape of Motors
The shape of the motors used for the Manipulator that you are using may be different from
the shape of the motors described in this manual because of the specifications.
Setting by Using Software
This manual contains setting procedures by using software. They are marked with the
following icon.
EPSON
RC+
vi G10 / G20 Rev.10
Table of Contents
Before Reading This Manual............................................................................v
Setup & Operation
1
. Safety ···························································································· 3
1.1 Conventions ...........................................................................................3
1.2 Design and Installation Safety ...............................................................4
1.3 Operation Safety ....................................................................................5
1.4 Emergency Stop ....................................................................................6
1.5 Emergency Movement Without Drive Power .........................................7
1.6 Manipulator Labels .................................................................................8
2
. Specifications ············································································ 10
2.1 Features of G10 series and G20 series Manipulators ..........................10
2.2 Model Number and Model Differences ................................................. 11
2.3 Part Names and Outer Dimensions .....................................................12
2.3.1 Table Top Mounting ........................................................................12
2.3.2 Wall Mounting .................................................................................18
2.3.3 Ceiling Mounting .............................................................................24
2.3.4 G10-65***/G10-85***: For S/N1**** or later ....................................30
2.4 Specifications .......................................................................................31
2.5 How to Set the Model ...........................................................................34
3
. Environments and Installation ·················································· 35
TABLE OF CONTENTS
3.1 Environmental Conditions ....................................................................35
3.2 Base Table ...........................................................................................37
3.3 Mounting Dimensions ..........................................................................38
3.4 Unpacking and Transportation .............................................................41
3.4.1 Precautions for Transportation .......................................................41
3.4.2 Transportation .................................................................................42
3.5 Installation ............................................................................................42
3.5.1 Table Top Mounting ........................................................................43
3.5.2 Wall Mounting .................................................................................44
3.5.3 Ceiling Mounting .............................................................................45
3.5.4 Cleanroom-model ...........................................................................46
3.5.5 Protected-model .............................................................................46
3.6 Connecting the Cables .........................................................................47
3.7 User Wires and Pneumatic Tubes .......................................................49
3.8 Relocation and Storage ........................................................................51
3.8.1 Precautions for Relocation and Storage .........................................51
3.8.2 Table Top Mounting ........................................................................52
3.8.3 Wall Mounting .................................................................................53
3.8.4 Ceiling Mounting .............................................................................54
G10 / G20 Rev.10 vii
TABLE OF CONTENTS
4
. Setting of End Effectors ··························································· 55
4.1 Attaching an End Effector .................................................................... 55
4.2 Attaching Cameras and Valves ........................................................... 57
4.3 Weight and Inertia Settings ................................................................. 58
4.4 Precautions for Auto Acceleration/Deceleration of Joint #3 ................. 67
5
. Motion Range ············································································ 68
5.1 Motion Range Setting by Pulse Range (for All Joints) ......................... 69
5.2 Motion Range Setting by Mechanical Stops ........................................ 72
5.3 Setting the Cartesian (Rectangular) Range in the XY Coordinate
5.4 Standard Motion Range ....................................................................... 79
4.3.1 Weight Setting ................................................................................ 58
4.3.2 Inertia Setting ................................................................................. 62
5.1.1 Max. Pulse Range of Joint #1 ........................................................ 69
5.1.2 Max. Pulse Range of Joint #2 ........................................................ 70
5.1.3 Max. Pulse Range of Joint #3 ........................................................ 71
5.1.4 Max. Pulse Range of Joint #4 ........................................................ 71
5.2.1 Setting the Mechanical Stops of Joints #1 and #2 ......................... 73
5.2.2 Setting the Mechanical Stop of Joint #3 ......................................... 76
System of the Manipulator (for Joints #1 and #2) ............................... 78
Maintenance
1
. Safety Maintenance ··································································· 85
2
. General Maintenance ································································ 86
2.1 Schedule for Maintenance Inspection ................................................. 86
2.2 Inspection Point ................................................................................... 87
2.2.1 Inspection While the Power is OFF (Manipulator is not operating) . 87
2.2.2 Inspection While the Power is ON (Manipulator is operating) ......... 87
2.3 Greasing .............................................................................................. 88
2.4 Tightening Hexagon Socket Head Cap Bolts ...................................... 89
2.5 Matching Origins ................................................................................. 91
2.6 Layout of Maintenance Parts ............................................................... 91
2.6.1 Table Top Mounting ........................................................................ 91
2.6.2 Wall Mounting ................................................................................ 93
2.6.3 Ceiling Mounting ............................................................................ 95
2.6.4 G10-65***: For S/N1**** or later .................................................... 97
3
. Cover ·························································································· 98
3.1 Arm Top Cover .................................................................................. 100
3.2 Arm Bottom Cover ............................................................................. 102
3.3 Arm #1 Cover .................................................................................... 103
3.3.1 G10/G20-***S*, G10/G20-***C* ................................................... 103
3.3.2 G10/G20-***D*, P* ....................................................................... 104
viii G10 / G20 Rev.10
TABLE OF CONTENTS
3.4 Connector Plate .................................................................................105
3.5 Connector Sub Plate ..........................................................................106
3.6 User Plate ..........................................................................................107
3.7 Maintenance Plate .............................................................................107
3.8 Base Bottom Cover ............................................................................108
4
. Cable Unit ················································································· 109
4.1 Replacing Cable Unit ......................................................................... 110
4.2 Wiring Diagrams ................................................................................122
4.2.1 Signal Cable .................................................................................122
4.2.2 Power Cable .................................................................................123
4.2.3 User Cable ....................................................................................124
5
. Arm #1 ······················································································ 125
5.1 Replacing Joint #1 Motor ...................................................................126
5.2 Replacing Joint #1 Reduction Gear Unit ............................................128
6
. Arm #2 ······················································································ 131
6.1 Replacing Joint #2 Motor ...................................................................132
6.2 Replacing Joint #2 Reduction Gear Unit ............................................137
7
. Arm #3 ······················································································ 140
7.1 Replacing Joint #3 Motor ...................................................................141
7.2 Replacing the Timing Belt ..................................................................145
7.2.1 G10 ...............................................................................................146
7.2.2 G20 ...............................................................................................150
7.3 Replacing the Brake ...........................................................................151
. Arm #4 ······················································································ 153
8
8.1 Replacing Joint #4 Motor ...................................................................154
8.1.1 G10 ...............................................................................................154
8.1.2 G20 ...............................................................................................158
8.2 Replacing the Timing Belt ..................................................................160
8.2.1 G10 ...............................................................................................161
8.2.2 G20 ...............................................................................................165
8.3 Replacing the Brake ...........................................................................170
8.4 Replacing the Reduction Gear Unit ....................................................173
8.4.1 G10 ...............................................................................................174
8.4.2 G20 ...............................................................................................175
9
. Bellows ····················································································· 177
G10 / G20 Rev.10 ix
TABLE OF CONTENTS
10. Ball Screw Spline Unit ························································· 180
10.1 Greasing the Ball Screw Spline Unit ................................................ 181
10.2 Replacing the Ball Screw Spline Unit .............................................. 184
1
1. Lithium Battery ······································································ 196
11.1 Replacing the Battery Unit (Lithium Battery) .................................... 197
11.2 Replacing the Battery Board ............................................................ 199
1
2. LED Lamp ·············································································· 201
1
3. Radiating Unit ········································································ 203
1
4. Calibration ············································································· 205
10.1.1 Standard-model ........................................................................... 181
10.1.2 Cleanroom-model / Protected-model........................................... 182
10.2.1 G10 .............................................................................................. 184
10.2.2 G20 .............................................................................................. 191
14.1 About Calibration ............................................................................. 205
14.2 Calibration Procedure ...................................................................... 206
14.3 Accurate Calibration of Joint #2 ....................................................... 216
14.4 Calibration Procedure without using Calibration Wizard .................. 218
1
5. Maintenance Parts List ························································· 222
15.1 Common Parts ................................................................................ 222
15.2 Parts by Environment Model ........................................................... 224
x G10 / G20 Rev.10
Setup & Operation
This volume contains information for setup and operation of the
G10 / G20 series Manipulators.
Please read this volume thoroughly before setting up and
operating the Manipulators.
1. Safety
Installation and transportation of robots and robotic equipment shall be performed by
qualified personnel and should conform to all national and local codes. Please read this
manual and other related manuals before installing the robot system or before connecting
cables.
Keep this manual handy for easy access at all times.
1.1 Conventions
Important safety considerations are indicated throughout the manual by the following
symbols. Be sure to read the descriptions shown with each symbol.
WARNING
WARNING
Setup & Operation 1. Safety
This symbol indicates that a danger of possible serious
injury or death exists if the associated instructions are not
followed properly.
This symbol indicates that a danger of possible serious
injury or death caused by electric shock exists if the
associated instructions are not followed properly.
This symbol indicates that a danger of possible harm to
people or physical damage to equipment and facilities
CAUTION
exists if the associated instructions are not followed
properly.
G10 / G20 Rev.10 3
Setup & Operation 1. Safety
1.2 Design and Installation Safety
Only trained personnel should design and install the robot system. Trained
personnel are defined as those who have taken robot system training and
maintenance training classes held by the manufacturer, dealer, or local
representative company, or those who understand the manuals thoroughly and
have the same knowledge and skill level as those who have completed the training
courses.
To ensure safety, a safeguard must be installed for the robot system. For details
on the safeguard, refer to the Installation and Design Precautions in the Safety
chapter of the EPSON RC+ User’s Guide.
The following items are safety precautions for design personnel:
■
Personnel who design and/or construct the robot system with this product must
read the Safety chapter in the EPSON RC+ User’s Guide to understand the
safety requirements before designing and/or constructing the robot system.
Designing and/or constructing the robot system without understanding the safety
requirements is extremely hazardous, may result in serious bodily injury and/or
severe equipment damage to the robot system, and may cause serious safety
problems.
WARNING
■
The Manipulator and the Controller must be used within the environmental
conditions described in their respective manuals. This product has been
designed and manufactured strictly for use in a normal indoor environment.
Using the product in an environment that exceeds the specified environmental
conditions may not only shorten the life cycle of the product but may also cause
serious safety problems.
■
The robot system must be used within the installation requirements described in
the manuals. Using the robot system outside of the installation requirements
may not only shorten the life cycle of the product but also cause serious safety
problems.
Further precautions for installation are mentioned in the chapter Setup &
Operation: 3. Environments and Installation. Please read this chapter carefully to
understand safe installation procedures before installing the robots and robotic
equipment.
4 G10 / G20 Rev.10
1.3 Operation Safety
The following items are safety precautions for qualified Operator personnel:
■
Please carefully read the Safety-related Requirements in the Safety chapter of
the EPSON RC+ User’s Guide before operating the robot system. Operating
the robot system without understanding the safety requirements is extremely
hazardous and may result in serious bodily injury and/or severe equipment
damage to the robot system.
■
Do not enter the operating area of the Manipulator while the power to the robot
system is turned ON. Entering the operating area with the power ON is
extremely hazardous and may cause serious safety problems as the Manipulator
may move even if it seems to be stopped.
■
WARNING
Before operating the robot system, make sure that no one is inside the
safeguarded area. The robot system can be operated in the mode for teaching
even when someone is inside the safeguarded area.
The motion of the Manipulator is always in restricted (low speeds and low power)
status to secure the safety of an operator. However, operating the robot system
while someone is inside the safeguarded area is extremely hazardous and may
result in serious safety problems in case that the Manipulator moves
unexpectedly.
Setup & Operation 1. Safety
WARNING
CAUTION
■
Immediately press the Emergency Stop switch whenever the Manipulator moves
abnormally while the robot system is operated.
■
To shut off power to the robot system, pull out the power plug from the power
source. Be sure to connect the AC power cable to a power receptacle. DO
NOT connect it directly to a factory power source.
■
Before performing any replacement procedure, turn OFF the Controller and
related equipment, and then pull out the power plug from the power source.
Performing any replacement procedure with the power ON is extremely
hazardous and may result in electric shock and/or malfunction of the robot
system.
■
Do not insert or pull out the motor connectors while the power to the robot system
is turned ON. Inserting or pulling out the motor connectors with the power ON is
extremely hazardous and may result in serious bodily injury as the Manipulator
may move abnormally, and also may result in electric shock and/or malfunction of
the robot system.
■
Whenever possible, only one person should operate the robot system. If it is
necessary to operate the robot system with more than one person, ensure that all
people involved communicate with each other as to what they are doing and take
all necessary safety precautions.
G10 / G20 Rev.10 5
Setup & Operation 1. Safety
1.4 Emergency Stop
If the Manipulator moves abnormally during operation, immediately press the Emergency
Stop switch. Stops the power supply to the motor, and the arm stops in the shortest
distance with the dynamic brake and mechanical brake.
However, avoid pressing the Emergency Stop switch unnecessarily while the Manipulator
is running normally. Otherwise, the Manipulator may hit the peripheral equipment since
the operating trajectory while the robot system stops is different from that in normal
operation.
To place the system in emergency mode during normal operation, press the Emergency
Stop switch when the Manipulator is not moving.
Refer to the Controller manual for instructions on how to wire the Emergency Stop switch
circuit.
Free running distance in emergency
The operating Manipulator cannot stop immediately after the Emergency Stop switch is
pressed.
The free running time/angle/distance of the Manipulator are shown below. However,
remember that the values vary depending on following conditions.
Weight of the end effector Weight of work piece Operating pose
Weight Speed Accel etc.
Conditions for Measurement
G10 G20
Accel Setting 100 100
Speed Setting 100 100
Load [kg] 10 20
Weight Setting 10 20
Point where the
emergency stop
signal is input
Joint #1
Stop point
Joint #2
Controller RC180 / RC620
Manipulator G10-65*** G10-85*** G20-85*** G20-A0***
Joint #1 + Joint #2 [sec.] 0.6 0.7 1.0 1.3 Free running
time
Free running
angle
Free running
distance
Joint #3 [sec.] 0.6 0.5 0.5 0.8
Joint #1 [deg.] 80 70 80 110
Joint #2 [deg.] 70 50 40 50
Joint #1 + Joint #2 [deg.] 110 120 110 160
Joint #3 G10/G20-**1** [mm]
G10/G20-**4**
90
210
80
160
Start point of
operation
Target point
70
200
90
170
6 G10 / G20 Rev.10
A
A
−
1.5 Emergency Movement Without Drive Power
When the system is placed in emergency mode, push the arm or joint of the Manipulator
by hand as shown below:
Arm #1 Push the arm by hand.
Arm #2 Push the arm by hand.
Joint #3 The joint cannot be moved up/down by hand until the electromagnetic brake
applied to the joint has been released. Move the joint up/down while
pressing the brake release button switch.
Joint #4 The shaft cannot be rotated by hand until the electromagnetic brake applied to
the shaft has been released.
Move the shaft while pressing the brake release button switch.
Setup & Operation 1. Safety
Joint #3 and #4
brake release button
rm #2
Joint #3
(up and down)
Joint #2
(rotating)
−
+
+
Shaft
−
+
Joint #1
(rotating)
−
+
rm #1
Base
Joint #4
(rotating)
NOTE
)
The brake release button affects both Joints #3 and #4. When the brake release button is
pressed in emergency mode, the brakes for both Joints #3 and #4 are released
simultaneously.
Be careful of the shaft falling and rotating while the brake release button is pressed
because the shaft may be lowered by the weight of an end effector.
G10 / G20 Rev.10 7
Setup & Operation 1. Safety
1.6 Manipulator Labels
The following labels are attached near the locations of the Manipulator where specific
dangers exist.
Be sure to comply with descriptions and warnings on the labels to operate and maintain
the Manipulator safely.
Do not tear, damage, or remove the labels. Use meticulous care when handling those
parts or units to which the following labels are attached as well as the nearby areas:
Location Labels NOTE
A
B
C
D
Before loosening the base mounting screws,
hold the arm and secure it tightly with a band to
prevent hands or fingers from being caught in the
Manipulator.
Hazardous voltage exists while the Manipulator
is ON. To avoid electric shock, do not touch any
internal electric parts.
You can catch your hand or fingers between the
shaft and cover when bringing your hand close to
moving parts.
* Manipulators with bellows do not have this label
for no danger of your hand or fingers being
caught.
Only authorized personnel should perform sling
work and operate a crane. When these
E
operations are performed by unauthorized
personnel, it is extremely hazardous and may
result in serious bodily injury and/or severe
equipment damage to the robot system.
F
Be careful of the hand falling while the brake release
button is being pressed.
8 G10 / G20 Rev.10
Setup & Operation 1. Safety
A
A
G
H
Location of Labels
Table Top Mounting: G10/G20-**** Wall Mounting: G10/G20-****W
D
F
C
C
E
B
G
A
C
D
F
B
H
G
E
Ceiling Mounting: G10/G20-****R
C
F
B
D
H
H
E
C
G
G10 / G20 Rev.10 9
Setup & Operation 2. Specifications
2. Specifications
2.1 Features of G10 series and G20 series Manipulators
The G10 series and G20 series Manipulators are high-performance manipulators intended
to achieve high speed, high accuracy, space saving, and high cost-performance.
The G10 series Manipulators are optimized for high speed assembly and alignment
procedure using multiple-hand.
The G20 series Manipulators are optimized for heavy payload transfer and alignment
packing procedure. The 1000 mm long arm model of the G20 series enables wide range
motion.
The features of the G10 series and G20 series Manipulators are as follows:
Compatibility with E2H Manipulators (our existing models)
The installation procedure and mounting dimensions of the end effector are compatible
with those for the E2H Manipulators (our existing models).
Space Saving
Compactness achieved by using a ductless design.
Reduce the system height by the new short stroke (Z: 180 mm) lineup.
Motion Range Extended
The motion range has been extended by 20% compared to the E2 series.
Improved Productivity
The numbers of user wires and pneumatic tubes have been increased.
The speed of Joints #1, 2, 3, and 4 has been enhanced.
Cycle time has been improved.
Increased Load Capacity
The load capacity has been increased to handle greater work load.
G10: Max. 10 kg
G20: Max. 20 kg
Increased Inertia
The available end effector capacity has been enlarged to enable larger multiple-hand
that holds multi-kind and different types of work piece.
Allowable moment of inertia has been enlarged according to the load.
G10: Max. 0.25 kgm
G20: Max. 0.45 kgm
Various Types Available
Long stroke (Z: 420 mm)
Short stroke (Z: 180 mm)
2
2
10 G10 / G20 Rev.10
2.2 Model Number and Model Differences
Setup & Operation 2. Specifications
G10-85 4 S □ -UL
UL specification
UL : UL compliant
□
: Non UL compliant
Type
□
: Table Top mounting
W : Wall mounting
R : Ceiling mounting
Environment
S : Standard
C : Cleanroom
D : Protected : IP 54 (with bellows option)
P : Protected : IP 65
Joint #3 stroke
: 180 mm (G10/G20***S* / D*)
1
: 150 mm (G10/G20***C* / P* / D* bellows option)
: 420 mm (G10/G20***S* / D*)
4
: 390 mm (G10/G20***C* / P* / D* bellows option)
Arm Length
65 : 650 mm (G10 series only)
85 : 850 mm
A0 : 1000 mm (G20 series only)
Series
G10 : G10 series
G20 : G20 series
Environment
Cleanroom-model
Cleanroom-model Manipulator includes additional features that reduce dust emitted by the
Manipulator to enable use in clean room environments.
Protected-model (IP54 / IP65)
The protected-model Manipulators operate under adverse conditions with dust and oily smoke.
• G10/G20-***D*
Normal G10/G20-***D* Manipulators do not have bellows. The normal G10/G20-***D*
Manipulator (without bellows option) operates under adverse conditions with oily mist. If
necessary, select the bellows option at shipment.
The Manipulators with bellows (option) comply with grade of protection IP54 (IEC 60529, JIS
C0920).
• G10/G20-***P*
G10/G20-***P* Manipulators comply with grade of protection IP65 (IEC 60529, JIS C0920).
For details on the specifications, refer to Setup & Operation: 2.4 Specifications.
G10 / G20 Rev.10 11
Setup & Operation 2. Specifications
−
−
2.3 Part Names and Outer Dimensions
NOTE
)
G10-65***/G10-85*** manipulator of S/N: 1**** or later is different from other models
in its form.
S/N: 1**** or later.
2.3.1 Table Top Mounting
Standard-model : G10/G20-***S
Joint #3 and #4
brake release button
LED lamp
Arm #2
For the detail, refer to Setup & Operation 2.3.4 G10-65***/G10-85***: For
Joint #2
(rotating)
−
+
Joint #1
(rotating)
+
Arm #1
Base
+
Joint #3
(up and down)
−
Joint #4
(rotating)
Signature label
(Serial No. of Manipulator)
User connector
(9-pin D-sub connector)
Signal cable
Fitting (white)
for ø 6 mm pneumatic tube
Fitting (white)
for ø 4 mm pneumatic tube
Shaft
+
MT label
(only for custom specification)
CE label
UR label
User connector
(15-pin D-sub connector)
Power cable
Fitting (black)
for ø 6 mm pneumatic tube
Fitting (black)
for ø 4 mm pneumatic tube
NOTE
)
- The brake release button affects both Joints #3 and #4. When the brake release button is pressed
in emergency mode, the brakes for both Joints #3 and #4 are released simultaneously.
- When the LED lamp is lighting or the controller power is on, the current is being applied to the
manipulator. Performing any work with the power ON is extremely hazardous and it may result
in electric shock and/or improper function of the robot system. Make sure to turn OFF the
controller power before the maintenance work.
12 G10 / G20 Rev.10
Setup & Operation 2. Specifications
G10-65*S G10/G20-85*S G20-A0*S
a 250 450 600
G10/G20-**1S G10/G20-**4S
b 180 420
c 813.5 1053.5
d213.5 -26.5
(Mount eyebolt
at shipment)
(*) indic ates the stroke margin by mechanical stop.
1 mm flat cut
Conical hole ø4,90°
Max.ø18 through hole
ø25 h7 shaft diameter
ø39.5 mechanic al stop diameter
Detail of “A”
(Calibration point position of Joints #3 and #4)
Reference through hole
(View from the bottom of the base)
90 or more
Space f or cables
Root both side chamfer C0.5
G10 / G20 Rev.10 13
Setup & Operation 2. Specifications
Cleanroom-model G10/G20-***C
The following figure shows the additional parts and specifications for the Table Top mounting
Cleanroom-model when compared with the Standard-model in appearance.
Upper bellows
Lower bellows
Plate cover
(For static electricity
countermeasure)
Plate cover
(For static electricity
countermeasure)
Cover
for Table Top mounting surface
14
Exhaust port
G10 / G20 Rev.10
Setup & Operation 2. Specifications
(
)
(Mount eyebolt
at shipment)
G10-65*C G10/G20-85*C G20-A0*C
a 250 450 600
G10/G20-**1C G10/G20-**4C
b 150 390
c 870.5 1129.5
d 205.5 -34.5
(*) indicates the stroke margin by mechanical stop.
1 mm flat cut
Conical hole
ø4,90°
Max.ø18 through hole
ø25 h7 shaft diameter
ø39.5 mechanical stop diameter
Detail of “A”
Calibration point position of Joints #3 and #4
Root both side chamfer C0.5
Reference through hole
(View from the bottom of the base)
90 or more
Space for cables
G10 / G20 Rev.10 15
Setup & Operation 2. Specifications
Protected-model G10/G20-***D / P
The following figure shows the additional parts and specifications for the Table Top mounting
Protected-model when compared with the Standard-model in appearance.
Normal G10/G20-***D* Manipulators do not have bellows. If necessary, select the bellows option at
shipment. The following figure is a Manipulator with bellows option.
For dimensions of the end part of G10/G20-***D* without bellows option, refer to G10/G20-***S.
Stainless steel plate
Upper bellows
Lower bellows
G10/G20-***P only
Plate cover (For oil resistant)
G10/G20-***P only
Plate cover (For oil resistant)
User connector
(Protected-model)
Joint #3 and #4
brake release button
(Protected-model)
Fittings with cover
(Protected-model)
Stainless steel plate
Stainless steel plate
for Table Top mounting surface
NOTE
)
16
Exhaust port
Fittings with cover
(Protected-model)
User connector
(Protected-model)
For Protected-model, all the screws used for outer parts are stainless steel screws. (Excluding the
screw used for mechanical stop.)
G10 / G20 Rev.10
Setup & Operation 2. Specifications
(
)
(Mount eyebolt
at shipment)
G10-65*P G10/G20-85*P G20-A0*P
a 250 450 600
G10/G20-**1P G10/G20-**4P
b 150 390
c874 1133
d 205.5 -34.5
(*) indicates the stroke margin by mechanical stop.
1 mm flat cut
Conical hole ø4,90°
Max.ø18 through hole
ø25 h7 shaft diameter
ø39.5 mechanical stop diameter
Detail of “A”
Calibration point position of Joints #3 and #4
Root both side chamfer C0.5
Reference through hole
(View from the bottom of the base)
90 or more
Space for cables
G10 / G20 Rev.10 17
Setup & Operation 2. Specifications
−+ −
2.3.2 Wall Mounting
Standard-model G10/G20-***SW
Joint #2
(rotating)
Joint #3 and #4
brake release button
LED lamp
MT label
(only for custom specification)
Signature label
(Serial No. of Manipulator)
CE label
UR label
Base
Arm #1
+
(up and down)
NOTE
)
Joint #1
(rotating)
Joint #3
+
−
−
Joint #4
(rotating)
Shaft
+
Arm #2
User connector
(15-pin D-sub connector)
Fitting (white)
for ø 6 mm pneumatic tube
User connector
(9-pin D-sub connector)
Power cable
Signal cable
Fitting (black)
for ø 4 mm pneumatic tube
Fitting (white)
for ø 4 mm pneumatic tube
Fitting (black)
for ø 6 mm pneumatic tube
- The brake release button affects both Joints #3 and #4. When the brake release button is pressed
in emergency mode, the brakes for both Joints #3 and #4 are released simultaneously.
- When the LED lamp is lighting or the controller power is on, the current is being applied to the
manipulator. Performing any work with the power ON is extremely hazardous and it may result in
electric shock and/or improper function of the robot system. Make sure to turn OFF the controller
power before the maintenance work.
18
G10 / G20 Rev.10
Loading...