Epson 83, 822 User Manual

0 (0)

User's Guide

Notations Used in This Guide

f Safety Indications

So that you can use the projector safely and correctly, symbols are applied in the documentation and on the projector to indicate possible harm to the user or to others and the risk of damage to property. The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.

Warning

Caution

f General Information Indications

Attention

Indicates the possibility of death or serious injury if this symbol is ignored or if sufficient care is not taken.

Indicates the possibility of injury or damage to property if this symbol is ignored or if sufficient care is not taken.

Indicates procedures which may result in damage or injury if sufficient care is not taken.

Indicates additional information and points which may be useful to know regarding a topic.

Procedure

[ (Name) ]

"(Menu Name)"

Indicates a page where detailed information regarding a topic can be found.

Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary" section of the "Appendices". s p.65

Indicates operating methods and the order of operations. The procedure indicated should be carried out in the order of the numbered steps.

Indicates the name of the buttons on the remote control or the control panel. Example: [Esc] button

Indicates configuration menu items. Example: "Image" - "Brightness"

Indicates that the explanation continues on the following page. Clicking this symbol will display the following page.

Indicates that the explanation is continued from the previous page. Clicking this symbol will display the previous page.

Projector Features......................................................................................4

Part Names and Functions ........................................................................5

Front/Top.............................................................................................................. 5

Rear (EMP-83/822 Only)...................................................................................... 6

Rear (EMP-X5/S5 Only) ....................................................................................... 7

Control Panel ....................................................................................................... 8

Remote Control .................................................................................................. 10

Base ................................................................................................................... 11

Useful Functions

Changing the Projected Image (Source Search) ...................................13

Functions for Enhancing Projection.......................................................14

Selecting the Projection Quality (Selecting Color Mode) ...................................14

Hiding the Image and Sound Temporarily (A/V Mute) ....................................... 15

Freezing the Image (Freeze).............................................................................. 16

Changing the Aspect Ratio (Aspect) .................................................................. 16

Enlarging Part of the Image (E-Zoom) ...............................................................17

Security Functions ...................................................................................18

Managing Users (Password Protect) ................................................................. 18

Restricting Operation (Operation Lock).............................................................. 20

Anti-Theft Lock ................................................................................................... 21

Configuration Menu

Using the Configuration Menu ................................................................23

List of Functions.......................................................................................24

Image Menu (EMP-83/822 Only) ....................................................................... 24

Image Menu (EMP-X5/S5 Only)......................................................................... 25

Signal Menu (EMP-83/822 Only) ....................................................................... 26

Signal Menu (EMP-X5/S5 Only)......................................................................... 27

Settings Menu ....................................................................................................28

Extended Menu .................................................................................................. 29

Network Menu (EMP-83/822 Only) .................................................................... 31

Info Menu (Display Only).................................................................................... 34

Reset Menu........................................................................................................ 35

Appendices

Installation Methods ................................................................................ 49

Cleaning .................................................................................................... 50

Cleaning the Projector's Surface ....................................................................... 50

Cleaning the Lens .............................................................................................. 50

Cleaning the Air Filter and Air Intake Vent......................................................... 50

Replacing Consumables .........................................................................51

Replacing the Remote Control Batteries ........................................................... 51

Replacing the Lamp ........................................................................................... 52

Replacing the Air Filter ...................................................................................... 56

Saving a User's Logo............................................................................... 57

Screen Size and Distance........................................................................59

EMP-83/822/X5 ................................................................................................. 59

EMP-S5 ............................................................................................................. 60

Connecting to External Equipment ........................................................61

Connecting to an External Monitor .................................................................... 61

Connecting to External Speakers (EMP-83/822 Only) ...................................... 61

Connecting a LAN Cable (EMP-83/822 Only)......................................... 62

Connecting a USB Cable (EMP-X5/S5 Only)..........................................63

Optional Accessories and Consumables ..............................................64

Glossary.................................................................................................... 65

ESC/VP21 Commands ............................................................................. 67

Command List.................................................................................................... 67

Cable Layouts.................................................................................................... 67

Connecting a USB (EMP-X5/S5 Only)............................................................... 68

USB Connection Setup ...................................................................................... 68

PJLink (EMP-83/822 Only)....................................................................... 69

List of Supported Monitor Displays ....................................................... 70

Specifications...........................................................................................71

Appearance............................................................................................... 75

Index.......................................................................................................... 76

Troubleshooting

Using the Help ..........................................................................................37

Problem Solving .......................................................................................38

Reading the Indicators ....................................................................................... 38

When the Indicators Provide No Help ................................................................ 41

Projector Features

Ease of use

f The A/V mute slide makes it easy to project and store

You can stop and resume projection easily by opening and closing the A/V mute slide which makes giving clear presentations easier.

f A single foot design means you do not have to make any difficult

levelling adjustments

You can easily make height adjustments with one hand. sQuick Start Guide

Enhanced security functions

f Password Protect to restrict and manage users

By setting a password you can restrict who can use the projector. s p.18

f Operation Lock restricts button operation on the control panel

You can use this to prevent people from changing projector settings without permission at events, in schools, and so on. s p.20

f Equipped with various anti-theft devices

The projector is equipped with the following security devices. s p.21

• Security slot

• Security cable installation point

Easy to handle

f Direct power On/Off (EMP-83/822 only)

In places where power is managed centrally, such as in a conference room, the projector can be set to power on and off automatically when the power source to which the projector is connected is switched on or off.

f No cool down delay

After turning the projector's power off, you can disconnect the projector's power cable without having to wait for the projector to cool down first.

Part Names and Functions

Front/Top

Name Function

Control panel s p.8

Lamp cover Open this cover when replacing the projector's

lamp. s p.53

J I H

G F E D

Name Function

Front adjustable

feet

Foot adjust lever Pull out the foot lever to extend and retract the

A/V mute slide Slide shut when not using the projector to

Remote receiver Receives signals from the remote control.

Focus ring Adjusts the image focus. s Quick Start Guide

Zoom ring

(EMP-83/822/X5 only)

A/V mute slide

knob

Security slot (j) The security slot is compatible with the

Extend and adjust the position of the projected image when the projector is placed on a surface such as a desk. s Quick Start Guide

front foot. s Quick Start Guide

protect the lens. By closing during projection you can hide the image and the sound (A/V Mute). s Quick Start Guide, p.15

s Quick Start Guide

Adjusts the image size. s Quick Start Guide

Slide the knob to open and close the A/V mute slide.

Microsaver Security System manufactured by Kensington. s p.21

Air exhaust vent

Caution

Do not place objects that may become warped or otherwise affected by heat near the air exhaust vent and do not put your face or hands near the air exhaust vent while projection is in progress.

Part Names and Functions

Rear (EMP-83/822 Only)

FHGA

Name Function

Remote receiver Receives signals from the remote control.

s Quick Start Guide

Speaker

Monitor Out port Outputs the image signal from the computer

connected to the Computer1 input port to an external monitor. This is not available for

component video being input to any port other than the Computer1 input port.s p.61

Audio Out port Outputs the sound of the image currently being

projected to external speakers. s p.61

g signals or other signals

Name Function

RS-232C port When controlling the projector from a

computer, connect it to the computer with an RS-232C cable. This port is for control use and should not normally be used. s p.67

Computer1 input

port

Audio1 input port Connect to the audio out port of the computer

Computer2 input port

Audio2 input port Connect to the audio out port of the computer

S-Video input

port

Video input port

Audio-L/R input port

LAN port When a LAN cable is connected, you can

For video signals from a computer and component video sources.

connected to the Computer1 input port.

For video signals from a computer and component video sources.

connected to the Computer2 input port.

s Quick Start Guide

For S-videog signals from video sources.

For composite videog signals from video sources.

Connects to the audio out port of the equipment connected to the S-Video port or Video input port. s Quick Start Guide

monitor and control the projector over a LAN.

s p.62

g signals from other video

Power inlet Connects to the power cable.

s Quick Start Guide

Part Names and Functions

Rear (EMP-X5/S5 Only)

FIH

Name Function

Remote receiver Receives signals from the remote control.

s Quick Start Guide

Speaker

Power inlet Connects to the power cable.

s Quick Start Guide

Monitor Out port Outputs the image signal from the computer

connected to the Computer input port to an external monitor. This is not available for

component video being input to any port other than the Computer input port.s p.61

EGA

g signals or other signals

Name Function

Computer input

port

Audio-L/R input

port

Video input port

S-Video input

port

USB port (Type B) When showing a slide show in PowerPoint,

* Limited to computers with the following operating systems installed.

Windows 98/98SE/2000/Me/XP Home Edition/XP Professional Macintosh: OS 8.6 to 9.2/10.1 to 10.3

For video signals from a computer and component video sources.

Connects to the audio output port for the equipment you want to project from and inputs the audio. s Quick Start Guide

For composite videog signals from video sources.

For S-videog signals from video sources.

you can use the projector's remote control to move to the next slide/previous slide if it is connected to a computer by a USB cable. Also, you can use it as a control port when the projector is controlled by a computer. Even if the projector is connected to a computer by a USB cable, you cannot project the image on the computer. s p.63

g signals from other video

Part Names and Functions

Control Panel

f EMP-83/822/X5

CFED

f EMP-S5

Buttons without numbers operate in the same way as in the figure above. See the numbers in the table for the figure above.

Name Function

[Power] button Turns the projector power on or off.

s Quick Start Guide

Status indicators The color of the indicators and whether they

are flashing or lit indicates the status of the projector. s p.38

[Source Search]

button

[Enter] button If pressed during projection of computer signal

[v] [w] buttons Corrects keystone distortion.

[Help] button Displays and closes the help screen which

Changes to the next input source that is connected to the projector and is sending an image.s p.13

images, it automatically adjusts the tracking, synchronization, and position to project the optimum image. When a configuration menu or a help screen is displayed, it accepts and enters the current selection and moves to the next level.s p.23

If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s Quick Start Guide, p.23

shows you how to deal with problems if they occur.s p.37

[Esc] button Stops the current function.

If pressed when a configuration menu is displayed, it moves to the previous menu level.s p.23

[a] [b] buttons

(EMP-83/822/X5 only)

Press to adjust the volume. If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s Quick Start Guide, p.23

Part Names and Functions

Name Function

[Menu] button Displays and closes the configuration

menu.s p.23

[Wide] [Tele]

buttons (EMP-S5 only)

Adjusts the image size. If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s Quick Start Guide, p.23

Part Names and Functions

Remote Control

A B C

D E

O N M

L K J

I H

Name Function

[Menu] button Displays and closes the configuration menu.

s p.23

[Enter/Auto]

button

[Color Mode]

button

[Page] button

(Down) (Up) (EMP-X5/S5 only)

[E-Zoom] button

(+) (-)

If pressed during projection of computer signal images, it automatically adjusts the tracking, synchronization, and position to project the optimum image. s p.26 When a configuration menu or a help screen is displayed, it accepts and enters the current selection and moves to the next level.s p.23

Each time the button is pressed, the color mode changes.s p.14

When showing a slide show in PowerPoint, you can use the projector's remote control to move to the next slide/previous slide if it is

connected to a computer by a USB cable.

s p.63

(+) Enlarges the image without changing the projection size. (-) Reduces parts of the image that have been enlarged using the [+] button.s p.17

Illustrations show EMP-X5/S5.

Name Function

[Power] button Turns the projector power on or off.

s Quick Start Guide

[Source Search]

button

Changes to the next input source that is connected to the projector and is sending an image.s p.13

[A/V Mute] button Turns the video and audio on or off. s p.15

[Freeze] button Images are paused or unpaused.s p.16

[Aspect] button

Numeric buttons Use these buttons when entering a password.

* Limited to computers with the following operating systems installed.

Windows 98/98SE/2000/Me/XP Home Edition/XP Professional Macintosh: OS 8.6 to 9.2/10.1 to 10.3

The aspect ratiog changes each time the button is pressed.s p.16

s p.19

Part Names and Functions

Name Function

[Volume -] button

[Volume +] button

[Esc] button Stops the current function. If pressed when a

[Help] button Displays and closes the help screen which

[u] [d] buttons If pressed when a configuration menu or a help

Remote control

light-emitting area

Press [Volume -] to lower the volume and press [Volume +] to raise the volume. If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values.

s Quick Start Guide , p.23

configuration menu is displayed, it moves to the previous level. s p.23

shows you how to deal with problems if they occur.s p.37

screen is displayed, these buttons select menu items and setting values. s p.23

Outputs remote control signals.

s Quick Start Guide

Base

Name Function

Suspension

bracket fixing points (3 points)

Rear foot

(2 points)

Security cable

installation point

Air filter (Air

intake vent)

Attach the optional ceiling mount here when suspending the projector from a ceiling.　

s p.49, 64

Turn to extend and retract to adjust the horizontal tilt. s Quick Start Guide

Pass a commercially available anti-theft wire lock through here when you want to secure the projector to a fixed object. s p.21

This prevents dust and other foreign particles from getting inside the projector when air is drawn in. The projector displays a warning message when it is time to clean or replace the air filter.s p.50, 56

Useful Functions

This chapter explains useful functions for giving presentations and so on, and the security functions.

Changing the Projected Image

(Source Search) .................................................. 13

Functions for Enhancing Projection ................. 14

• Selecting the Projection Quality

(Selecting Color Mode) .....................................................14

• Hiding the Image and Sound Temporarily

(A/V Mute) .........................................................................15

• Freezing the Image (Freeze).............................................16

• Changing the Aspect Ratio (Aspect)................................16

• Enlarging Part of the Image (E-Zoom) ...........................17

Security Functions..............................................18

• Managing Users (Password Protect)............................... 18

Type of Password Protect .............................................................. 18

Setting Password Protect................................................................ 19

Entering the Password.................................................................... 20

• Restricting Operation (Operation Lock)........................ 20

• Anti-Theft Lock ................................................................ 21

Installing the wire lock................................................................... 21

Changing the Projected Image (Source Search)

The projector automatically detects signals being input from connected equipment, and the image being input from the equipment is projected. You can project the target image quickly because it skips input ports where no image is being input.

Computer1 Video

The input port where no image signal is being input is skipped.

* EMP-83/822 only

Procedure

S-VideoComputer2

The following screen showing the status of image signals is displayed when only the image that the projector is currently displaying is available, or when no image signal can be found. You can select the input port where the connected equipment you want to use is projecting. If no operation is performed after about 10 seconds, the screen closes.

For EMP-83/822

When your video equipment is connected, start playback before beginning this operation.

Using the remote control Using the control panel

When two or more pieces of equipment are connected, press the [Source Search] button until the target image is projected.

Functions for Enhancing Projection

Selecting the Projection Quality (Selecting Color Mode)

You can easily obtain the optimum image quality simply by selecting the setting that best corresponds to your surroundings when projecting. The brightness of the image varies depending on the mode selected.

Mode Application

Game Ideal for use in a bright room. This is the brightest

mode and reproduces shadow tones well.

Presentation Ideal for making presentations using color materials

in a bright room.

Text Ideal for making presentations using black-and-

white materials in a bright room.

Theatre Ideal for watching films in a dark room. This gives

images a natural tone.

Photo (When computer images are input)

Ideal for projecting still pictures, such as photos, in a bright room. This makes images vivid and brings them into contrast.

Sports (When component video, S-video, or composite

video images are input) Ideal for watching TV programmes in a bright room. This makes images vivid and brings them to life.

sRGBg Ideal for images that conform to the sRGB color

standard.

Blackboard Even if you are projecting onto a blackboard

(greenboard), this setting gives your images a natural tint, just like when projecting onto a screen.

Procedure

Remote control

Each time you press the button, the color mode name is displayed on the screen and the color mode changes.

If you press the button while the color mode name is displayed on the screen, it changes to the next color mode.

The color mode can also be set using "Color Mode" from

the "Image" menu in the configuration menu.

p.24, 25

Functions for Enhancing Projection

Hiding the Image and Sound Temporarily (A/V Mute)

You can use this when you want to focus the audience's attention on what you are saying, or if you do not want to show details such as when you are changing between files during presentations from a computer.

Procedure

Remote control Projector

• If you use this function when projecting moving images,

* Depending on the area of purchase, the User's Logo function may not be

available for EMP-X5/S5.

the images and sound continue to be played back by the source, and you cannot return to the point where A/V Mute was activated.

• From the remote control you can choose to display black, blue, or logo "Extended" - "Display" - "A/V Mute" setting in the configuration menu.

• When the A/V mute slide is closed and A/V Mute begins, the power supply can be set to automatically turn off after about 30 minutes by setting "Extended" - "Operation" "Lens Cover Timer" in the configuration menu.

as the A/V mute display using the

p.29

p.30

Each time you press the button, or the A/V mute slide is opened or closed, A/V Mute turns on or off.

Functions for Enhancing Projection

Freezing the Image (Freeze)

When the moving image on the screen is frozen, the image continues to project, so you can project a moving image one frame at a time like a still photo. Also, you can perform operations such as changing between files during presentations from a computer without projecting any images if the Freeze function is activated beforehand.

Procedure

Remote control

Each time you press the button, Freeze turns on or off.

• Audio does not stop.

• The image source continues to play back the moving images even while the screen is frozen, so it is not possible to resume projection from the point where it was paused.

• If the [Freeze] button is pressed while the configuration menu or a help screen is displayed, the menu or help screen being displayed is cleared.

• Freeze still works while E-Zoom is being used.

Changing the Aspect Ratio (Aspect)

When video equipment is connected, images that have been recorded in digital video or onto DVDs can be viewed in 16:9 wide-screen format. You can change the aspect ratiog for images in squeeze modeg as follows.

4:3

Procedure

Remote control

Each time you press the button, the aspect name is displayed on the screen and the aspect changes.

16:9

16:9 (Up)

16:9 (Down)

Functions for Enhancing Projection

If you press the button while the aspect name is displayed on the screen, it changes to the next aspect mode.

This can also be set using "Aspect" from the "Signal"

Enlarging Part of the Image (E-Zoom)

This is useful when you want to expand images such as graphs and tables to see them in greater detail.

menu in the configuration menu.

p.26

Move the cross to the area of the image that you want to enlarge.

Remote control

Cross

Enlarge.

Remote control

Procedure

Start E-Zoom.

Remote control

Each time the button is pressed, the area is expanded. You can expand quickly by holding the button down. You can reduce the enlarged image by pressing the [-] button. Press the [Esc] button to cancel.

• The enlargement ratio appears on the screen. The selected area can be enlarged to between 1 to 4 times in 25 incremental steps.

• You can scroll the image by pressing [u], [d], [l], or [r].

Security Functions

The projector has the following enhanced security functions.

• Password Protect You can limit who can use the projector.

• Operation Lock You can prevent people from changing the settings on the projector without permission.

• Anti-Theft Lock The projector is equipped with various types of anti-theft security devices.

Managing Users (Password Protect)

When the Password Protect function is activated, people who do not know the password cannot use the projector to project images even if the projector power is on. Furthermore, the user's logo that is displayed when you turn on the projector cannot be changed. This acts as an anti-theft device as the projector cannot be used even if it is stolen. At the time of purchase the Password Protect function is not activated.

f Type of Password Protect

The following three kinds of password protect settings can be made according to how the projector is being used.

• Settings for "Display Background", "Startup Screen", and "A/V Mute" are changed from "Display" in the configuration menu.

3 "Network Protect" (EMP-83/822 only)

When "Network Protect" is set to "On" setting changes for "Network" in the configuration menu are prohibited.

* Depending on the area of purchase, the User's Logo function may not be

available for EMP-X5/S5. In that case, "User's Logo Protect" is not displayed.

1. "Power On Protect"

When "Power On Protect" is "On", the password must be entered whenever the projector is turned on after it has been disconnected from the power supply to which it was connected the last time the password was entered. If the correct password is not entered, projection does not start.

2 "User's Logo Protect"

When "User's Logo Protect" is set to "On" the following setting changes are prohibited.

• Capturing a user's logo

Security Functions

f Setting Password Protect

Use the following procedure to set Password Protect.

Procedure

Hold down the [Freeze] button for about five seconds.

The password protect setting menu is displayed.

Remote control

• If Password Protect is already activated, you must enter the password. If the password is entered correctly, the password protect setting menu is displayed.

"Entering the Password" p.20

• When the password is set, stick the password protect sticker in a visible position on the projector as a further theft deterrent.

Turn on "User's Logo Protect"*.

(1) Select "User's Logo Protect", and then press the [Enter] button. (2) Select "On", and then press the [Enter] button. (3) Press the [Esc] button.

Turn on "Network Protect".

(1) Select "Network Protect", and then press the [Enter] button. (2) Select "On", and then press the [Enter] button. (3) Press the [Esc] button.

Set the password.

(1) Select "Password", and then press the [Enter] button. (2) When the message "Change the password?" is displayed, select

"Yes" and then press the [Enter] button. The default setting for the password is "0000". Change this to your own desired password. If you select "No", the screen shown in step 1 is displayed again.

(3) Enter a four digit number using the numeric buttons. The

number entered is displayed as "* * * *". When you enter the fourth digit, the confirmation screen is displayed.

Remote control

Numeric buttons

Turn on "Power On Protect".

(1) Select "Power On Protect", and then press the [Enter] button. (2) Select "On", and then press the [Enter] button. (3) Press the [Esc] button.

(4) Re-enter the password.

The message "Password accepted." is displayed. If you enter the password incorrectly, a message is displayed prompting you to re-enter the password.

Security Functions

* Depending on the area of purchase, the User's Logo function may not be

available for EMP-X5/S5. In that case, "User's Logo Protect" is not displayed.

f Entering the Password

When the password entry screen is displayed, enter the password using the numeric buttons on the remote control.

Procedure

Enter the password by using the numeric buttons.

When you enter the correct password, projection begins.

Attention

• If an incorrect password is entered three times in succession, the message "The projector's operation will be locked." is displayed for about five minutes, and then the projector switches to standby mode. If this happens, disconnect the power plug from the electrical outlet and then reinsert it and turn the projector's power back on. The projector displays the password entry screen again so that you can enter the correct password.

• If you have forgotten the password, make a note of the "Request Code: xxxxx" number that appears on the screen and contact the nearest address provided in the International Warranty Terms.

sInquiries

• If you continue to repeat the above operation and input the wrong password thirty times in succession, the following message is displayed and the projector does not accept any more password entries. "The projector's operation will be locked. Contact Epson as described in your documentation."

sInquiries

Restricting Operation (Operation Lock)

Do one of the following to lock the operation buttons on the control panel.

• Full Lock All of the buttons on the control panel are locked. You cannot perform any operations from the control panel, including turning the power on or off.

• Operation Lock All of the buttons on the control panel, except for the [Power] button, are locked.

This is useful at events or shows when you want to deactivate all buttons and only project, or at schools when you want to limit button operation. The projector can still be operated using the remote control.

Procedure

Press the [Menu] button and select "Settings" "Operation Lock" in the configuration menu. s "Using the Configuration Menu" p.23

Using the remote control Using the control panel

Security Functions

Check the buttons you can use and the operations they perform in the guide under the menu.

Select either "Full Lock" or "Operation Lock".

Anti-Theft Lock

As the projector is often setup on ceiling mounts and left in rooms unattended, it is possible that someone may try and take the projector, so the projector includes the following security devices.

• Security slot

The security slot is compatible with the Microsaver Security System manufactured by Kensington. You can find details about the Microsaver Security System on the Kensington homepage

http://www.kensington.com/.

• Security cable installation point

A commercially available theft-prevention wire lock can be passed through the installation point to secure the projector to a desk or pillar.

f Installing the wire lock

Pass an anti-theft wire lock through the installation point. See the documentation supplied with the wire lock for locking instructions.

Select "Yes" when the confirmation message is displayed.

The control panel buttons are locked according to the setting you chose.

You can release the control panel lock by one of the following two methods.

• From the remote control, select "Off" from "Settings" "Operation Lock" in the configuration menu.

• When you press and hold down the [Enter] button on the control panel for about seven seconds, a message is displayed and the lock is released.

Configuration Menu

This chapter explains how to use the configuration menu and its functions.

Using the Configuration Menu .......................... 23

List of Functions ................................................. 24

• Image Menu (EMP-83/822 Only).....................................24

• Image Menu (EMP-X5/S5 Only) .....................................25

• Signal Menu (EMP-83/822 Only).....................................26

• Signal Menu (EMP-X5/S5 Only) .....................................27

• Settings Menu ....................................................................28

• Extended Menu .................................................................29

• Network Menu (EMP-83/822 Only) ................................31

• Info Menu (Display Only).................................................34

• Reset Menu ........................................................................35

Using the Configuration Menu

Selecting from the top menu

Top menu

Guide

Selecting from the sub menu

Sub menu (Settings)

For EMP-83/822/X5

For EMP-S5

Changing the selected item

Exit

Buttons used

Using the control panel

For EMP-83/

822/X5

Using the remote control

For EMP-S5

Select the setting to change

List of Functions

Image Menu (EMP-83/822 Only)

Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each image signal.

Computer image

Sub Menu Function

Color Mode You can select the quality of the image to suit your surroundings. s p.14 Brightness You can adjust the image brightness. Contrastg You can adjust the difference between light and shade in the images. Color Saturation You can adjust the color saturation for the images. Tint (Adjustment is only possible when NTSC signals are being input if you use composite video/S-video.)

You can adjust the image tint.

Sharpness You can adjust the image sharpness. Color Adjustment You can make adjustments by choosing one of the following

Abs. Color Temp.: You can adjust the overall tint of the image. You can adjust tints in 10 stages from 5000 K to 10000 K. When a high value is

selected the image becomes tinged with blue, and when a low value is selected the image becomes tinged with red.

Red, Green, Blue: You can adjust the saturation of each color individually. (This item cannot be selected if "sRGB

Reset You can reset all adjustment values in the "Image" menu to their default settings. To return all menu items to their default settings, see s p.35

g" is selected as the "Color Mode" setting in the "Image" menu.)

Component videog/Composite videog/S-videog

+ 54 hidden pages

Epson 83, 822 User Manual

Notations Used in This Guide

Contents

Projector Features

Part Names and Functions

Front/Top

Rear (EMP-83/822 Only)

Rear (EMP-X5/S5 Only)

Control Panel

Remote Control

Base

Useful Functions

Changing the Projected Image (Source Search)

Functions for Enhancing Projection

Selecting the Projection Quality (Selecting Color Mode)

Hiding the Image and Sound Temporarily (A/V Mute)

Freezing the Image (Freeze)

Changing the Aspect Ratio (Aspect)

Enlarging Part of the Image (E-Zoom)

Security Functions

Managing Users (Password Protect)

Restricting Operation (Operation Lock)

Anti-Theft Lock

Configuration Menu

Using the Configuration Menu

List of Functions

Image Menu (EMP-83/822 Only)