Epson 780c User Manual
S
T
A
R
T
H
E
R
E
Connect the projector
to your notebook
Locate the required cables:
1
Epson®PowerLite®750c/760c
Quick Setup
Power cord VGA computer cable
Connect the computer cable to
2
the blue Computer/Component Video
port on the projector.
Connect the other end to your notebook’s video-out
3
or monitor port.
NOTE: If your notebook has a DVI connector, you need to use an
optional DVI-to-VGA adapter with the included computer cable
(see your computer’s documentation).
Follow these instructions to connect the projector to your
notebook. For other setup options, see your User’s Guide.
Connect the power cord to the
4
projector, then plug the other end
into an electrical outlet.
Turn on your equipment
Turn on your notebook.
1
Remove the projector’s lens cover.
2
Make sure the Power light
3
is orange and not flashing.
Power button
Adjust the image
If you’ve turned on your notebook and you don’t see an image,
1
press the Source Search button on the projector to select the
image source.
NOTE: If you still see a blank screen or have other display problems,
see the troubleshooting tips on the back of this sheet.
Turn the focus ring to sharpen the image.
2
Turn the zoom ring to reduce or enlarge the image.
Power light
Press the Power button
4
to turn on the projector.
CAUTION: Before unplugging the projector...
Shut down the projector properly:
1. Press the Power button twice.
2. When the orange light stops flashing and the projector beeps,
you can unplug the projector.
Zoom
Focus
If your image looks like or , you’ve placed the projector off
3
to one side of the screen at an angle. Place it directly in front of the
center of the screen, facing the screen squarely.
If your image looks like or , press the or buttons
4
on the projector to correct it.
Using the remote control
If this is your first time using the remote, make sure its batteries
1
are installed as shown.
Quick Setup
Epson PowerLite 750/760c
Troubleshooting
If you see a blank screen...
If you see a blank screen or the No signal message after turning on
your notebook, check the following:
Make sure the Power light on the projector is green and not flashing,
and the lens cover is off.
Press the Source Search button on the projector to select the
computer as the image source.
Turn off projector
display and sound
Choose which source
to display
Optimize the
computer image
Turn projector on and off
Zoom in on part of
the projected image
Navigate projector menus
Control projector volume
If you’re using a Windows
keyboard that lets you display on an external monitor. It may be
labelled CRT/LCD or have an icon such as . You may have to
hold down the Fn key while pressing it. Allow a few seconds for
the projector to sync up after changing the setting.
®
notebook, press the function key on your
If the projector and notebook don’t display the same image...
If your image displays either on the projector or notebook, but not on
both, check the following:
Windows
Try using the CRT/LCD or key as described above. On most systems,
this key lets you toggle between the LCD screen and the projector,
or display on both at the same time.
If that doesn’t work, check your monitor settings to make sure both the
LCD screen and the external monitor port are enabled.
You can use the remote control to operate the projector. With the USB
cable, you can use the remote as a wireless mouse. For more information
on using the remote control, see your User’s Guide.
Where to get help
Telephone Support Services
To use the Epson PrivateLine®Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included in your Start Here
kit. This service is available 6 AM to 6 PM, Pacific Time, Monday through
Friday, for the duration of your warranty period. You may also speak with
a projector support specialist by dialing one of these numbers:
U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Toll or long distance charges may apply.
1. From the Windows Control Panel, open the Display utility.
2. In the Display Properties dialog box, click the
Settings tab, then click Advanced.
3. The method for adjusting the setting varies;
you may have to click a Monitor tab, then
make sure the external Monitor port is set
as your primary display and/or enabled.
See your notebook’s manual or online help
for details.
Macintosh
1. From the Apple
Preferences, then select Displays.
2. Select the VGA Display or Color LCD
dialog box.
3. Click the Arrangement (or Arrange) tab
and click Mirror Displays.
®
OS X
®
menu, select System
Electronic Support Services
Epson provides technical assistance through electronic support services 24
hours a day at http://support.epson.com. For tips, templates, and training for
developing successful presentations go to http://www.presentersonline.com.
Register today to get product updates, special promotions, and customer-only offers. You can use the registration card or CD included in
your Start Here kit, or register online at www.epson.com/webreg.
Epson is a registered trademark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
© 2005 Epson America, Inc. 6/05
Printed in XXXXXXXXX
Macintosh OS 9.x or earlier
1. From the Apple menu, select Control
Panels, then click Monitors or
Monitors and Sound.
2. Click the Arrange icon.
3. Drag one monitor icon
on top of the other.
If the Arrange option isn’t available, click the
Monitor icon and select a Simulscan resolution.
CPD-20249
Loading...