Epic EPEX49050 Owner's Manual
Model No. EPEX4905.0
Serial No.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL FREE:
USER'S MANUAL
1-866-997-6999
Mon.–Fri., 6 a.m.–6 p.m. MST
THE WEB:
ON
www.iconservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO OPERATE THE EXERCISE CYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
EXPLODED DRA
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
2
IMPORTANT PRECAUTIONS
WARNING:
ions before using the exercise cycle.
t
1. Read all instructions in this manual and all
warnings on the exercise cycle before
using the exercise cycle.
2. Use the exerci se cycl e only as described in
this manual.
3. It is the responsibility of the owner to
ensure that all users of the exercise cycle
are adequately informed of all precautions.
4. Use the exercise cycle indoors on a level
surface. Keep the exercise cycle away from
moisture and dust. Place a mat under the
exercise cycle to protect the floor or carpet.
Make sure that there is enough clearance
around the exercise cycle to mount, dismount, and use it.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under the age of 12 and pets
away from the exercise cycle at all times.
To reduce the risk of serious injury, read the following important precau-
7. The exercise cycle should not be used by
persons weighing more than 250 pounds.
8. Wear suitable clothes when using the exercise cycle; do not wear loose clothes that
could become caught on the exercise cycle.
Always wear athletic shoes.
9. Always keep your back straight when using
the exercise cycle. Do not arch your back.
10.If you feel pain or dizziness while exercising, stop immediately and cool down.
11.The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12.The exercise cycle is intended for in-home
use only. Do not use the exercise cycle in a
commercial, rental, or institutional setting.
WARNING:Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
BEFORE YOU BEGIN
Congratulations for selecting the new EPIC 420 R
exercise cycle. Cycling is one of the most effective
exercises for increasing cardiovascular fitness, building
ndurance, and toning the entire body. The EPIC 420
e
R exercise cycle offers an impressive array of fea-
ures designed to let you enjoy this healthful exercise
t
in the comfort and privacy of your home.
For your benefit, read this manual carefully before
you use the exercise cycle.
after reading this manual, see the front cover of this
manual. To help us assist you, mention the product
Water Bottle Holder*
Bookrack
Handlebar/Pulse Sensor
If you have questions
model number and serial number when calling. The
model number is EPEX4905.0. The serial number can
be found on a decal attached to the exercise cycle
see the front cover of this manual for the location of
(
the decal).
To avoid a registration fee for any service needed
under warranty, you must register the exercise
cycle at www.iconservice.com/registration.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Fan
Console
FRONT
Seat
Backrest
Seat Handle
REAR
Leveling Foot
Seat Knob
Pedal/Strap
Wheel
RIGHT SIDE
No water bottle is included
*
4
ASSEMBLY
M10 Nylon
Locknut (63)–2
M8 Split
Washer (55)–12
M10 Split
Washer (88)–2
M8 Washer
(60)–4
M10 x 52mm Button Bolt (82)–2
M8 Nylon
Locknut (89)–4
M8 x 40mm Button
Bolt (81)–4
M10 x 118mm Button Screw (78)–2
M8 x 25mm Button
Screw (79)–4
M4 x 16mm
Screw (57)–5
1/4” x 16mm Button
Screw (80)–8
M8 x 40mm Button
Screw (54)–8
To hire an authorized technician to assemble the exercise cycle, call toll-free 1-800-445-2480.
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
ssembly requires the included tools and your own adjustable wrench .
A
Use the drawings below to identify the small parts used in assembly. The number in parenthesis below each
drawing refers to the key number of the part, from the PART LIST on page 21. The second number refers to the
quantity needed for assembly. Note: Some small parts may have been pre-assembled for shipping. I f a par t
is not in the parts bag, check to see if it has been pre-assembled.
1. Identify the Front Stabilizer (15). While anot her per son
lifts the front of the Frame (1), attach the Front
Stabilizer to the Frame with four M8 x 40mm Button
Screws (54) and four M8 Split Washers (55).
1
15
1
55
54
5
55
54
2. While another person lifts the rear of the Frame (1),
attach the Rear Stabilizer (16) to the Frame with four
8 x 40mm Button Screws (54) and four M8 Split
M
Washers (55).
2
1
16
55
3. Have another person hold the Upright (2) in the posi-
tion shown. See the inset drawing. Locate the wire
extending from the bottom of the Upright. Tie the wire
around the end of the Wire Harness (43) as shown.
Carefully pull the wire up through the Upright until the
Wire Harness is extending from the top of the Upright.
Then, untie the wire and discard it.
Carefully pull the end of the Wire Harness (43) to
remove any slack. Insert the Upright (2) into the
Frame (1); be careful to avoid pinching the Wire
Harness. Attach the Upright with two M10 x 118mm
Button Screws (78), two M10 Split Washers (88), and
two Upright Spacers (102). Make sure the concave
end of each Upright Spacer is turned toward the
Upright.
3
78
88
78
102
88
102
55
54
2
1
54
43
Do not pinch
the Wire
Harness (43)
during this
step.
Wire
43
4. Identify the Left Handlebar (70), which is marked with a
sticker. While another person holds the Left Handlebar
near the Upright (2), connect the left Pulse Sensor Wire
(6) to the Pulse Wire (3). Next, slide the Left Handlebar
onto the left tube on the Upright;
pinching the Wires. Insert two M8 x 40mm Button
Bolts (81) into the Left Handlebar and the tube on the
Upright; be careful not to damage the Wires with the
Button Bolts. Finger tighten two M8 Nylon Locknuts
(89) onto the Button Bolts. Next, slide the Handlebar
Collar (98) onto the upper end of the Left Handlebar.
Attach the Right Handlebar (72) as described above.
Note: As you slide the Right Handlebar onto the right
post on the Upright (2), insert the upper end of the
Right Handlebar into the Left Handlebar (70).
Connect the Handlebars (70, 72) with the Handlebar
Collar (98) and an M4 x 16mm Screw (57).
en the four M8 x 40mm Button Bolts (81);
the M8 Nylon Locknuts (89) are seated in the
hexagonal holes in the Handlebars.
be careful to avoid
Then, tight
make sure
6
4
Make sure the wires
do not get damaged
during this step.
98
57
70
3
81
-
6
Tube
89
72
2
5. Have another person hold the Console (4) near the
Upright (2).
5
Bookrack
Connect the Wire Harness (43) to the wire harness on
he Console (4). Next, connect the Pulse Wire (3) to
t
the pulse wire on the Console. Then, connect the indicated ground wire to the smallest wire on the Console.
Carefully insert all excess wiring down into the Upright
(2). Attach the Console (4) to the Upright with four M4
x 16mm Screws (57). Be careful to avoid pinching
the wires.
in the indicated location.
6. Attach the Seat (9) to the Seat Frame (7) with four 1/4”
x 16mm Button Screws (80) and four M8 Washers (60).
Next, press the bookrack onto the Console
4
3
4
3
2
57
6
9
Ground Wire
Do not pinch
the wires
during this step.
7. Attach the Seat Frame (7) to the Seat Carriage (11)
with two M10 x 52mm Button Bolts (82) and two M10
Nylon Locknuts (63).
7
60
60
7
82
80
63
7
1
1
7
8. Attach the Backrest (62) to the Backrest Frame (42)
with four 1/4” x 16mm Button Screws (80).
Slide the Backrest Frame (42) onto the Seat Frame
7). Attach the Backrest Frame with four M8 x 25mm
(
Button Screws (79) and four M8 Split Washers (55).
8
62
2
4
55
55
79
9. Identify the Left Pedal (22), which is marked with an
“L.” Using an adjustable wrench, firmly tighten the
Left Pedal
(24). Tighten the Right Pedal (not shown)
into the Right Crank Arm. Important: Tighten both
Pedals as firmly as possible. After using the
exercise cycle for one week, retighten the
Pedals. For best performance, t he P e da l s m us t
be kept tightened.
Identify the Left Pedal Strap (25), which is marked
with an “L.” Attach the Left Pedal Strap to the Left
Pedal (22), and adjust it to the desired position.
Attach and adjust the Right Pedal Strap (not shown)
in the same way.
counterclockwise
into the Left Crank Arm
clockwise
79
7
9
25
22
24
80
10. Make sure that all parts are properly tightened before you use the exercise cycle. Note: After assembly is
completed, some extra parts may be left over
. Place a mat beneath the exercise cycle to protect
the floor
.
8
Loading...