Epic EPEL79062 Owner's Manual

odel No. EPEL7906.2

M Serial No.

Write the serial number in the space above for reference.

Serial

Number

Decal

QUESTIONS?

If you have questions, or if parts are damaged or missing, DO NOT

CONTACT THE STORE; please contact Customer Care.

IMPORTANT: Please register this product (see the limited warranty on the back cover of this manual) before contacting Customer Care.

USERʼS MANUAL

CALL TOLL-FREE:

1-866-997-6999

Mon.–Fri. 6 a.m.–6 p.m. MT Sat. 8 a.m.–4 p.m. MT

ON THE WEB: www.iconservice.com

CAUTION

Read all precautions and instructions in this manual before using this equipment. Keep this manual for future reference.

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

HOW TO USE THE ELLIPTICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the warning decal(s). If a decal is missing or

illegible, see the front cover of this manual and request a free replacement decal. Apply the decal in the location shown.

Note: The decal(s) may not be shown at actual size.

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your elliptical before using your elliptical. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of

his product.

1. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.

2. Use the elliptical only as described in this manual.

3. It is the responsibility of the owner to ensure that all users of the elliptical are adequately informed of all precautions.

4. The elliptical is intended for home use only. Do not use the elliptical in a commercial, rental, or institutional setting.

5. Keep the elliptical indoors, away from moisture and dust. Do not put the elliptical in a garage or covered patio, or near water.

6. Place the elliptical on a level surface, with at least 3 ft. (0.9 m) of clearance in the front and rear of the elliptical and 2 ft. (0.6 m) on each side. To protect the floor or carpet from damage, place a mat under the elliptical.

9. The elliptical should not be used by persons weighing more than 350 lbs. (159 kg).

10. Wear appropriate clothes while exercising; do not wear loose clothes that could become caught on the elliptical. Always wear athletic shoes for foot protection while exercising.

11. Hold the handlebars or pulse sensors when mounting, dismounting, or using the elliptical.

12. The pulse sensor is not a medical device. Various factors may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general.

13. The elliptical does not have a freewheel; the pedals will continue to move until the flywheel stops. Reduce your pedaling speed in a controlled way.

14. Keep your back straight while using the elliptical; do not arch your back.

7. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.

8. Keep children under age 12 and pets away from the elliptical at all times.

15. Over exercising may result in serious injury or death. If you feel faint or if you experience pain while exercising, stop immediately and cool down.

BEFORE YOU BEGIN

Thank you for selecting the revolutionary EPIC™EL

OMMERCIAL PRO elliptical. The EL COMMERCIAL

C PRO elliptical provides an impressive selection of features designed to make your workouts at home more effective and enjoyable.

For your benefit, read this manual carefully before you use the elliptical. If you have questions after

Handlebar

Pulse Sensor

Water Bottle Holder*

reading this manual, please see the front cover of this

anual. To help us assist you, note the product model

m number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with the parts that are labeled in the drawing below.

Fan

Console

Pedal Disc

Handle

Leveling Foot

Ramp

Wheel

Pedal

*Water bottle is not included

ASSEMBLY

#8 x 3/4"

Screw (78)–4

5/16" x 1" Patch

Screw (81)–11

#10 x 1/2"

Screw (79)–10

5/16" x 1.5" Button

Bolt (73)–4

5/16" Washer

(104)–6

#10 Fender

Washer (80)–10

5/8" Wave

Washer (102)–6

5/16" Split

Washer (105)–5

5/16" Locknut

(106)–4

M10 x 20mm Patch

Screw (108)–6

Pivot Spacer

(71)–4

5/16" x 2 1/2" Button

Screw (88)–8

M10 Split

Washer (110)–6

M6 Split

Washer

(111)–10

To hire an authorized service technician to assemble the elliptical, call 1-800-445-2480.

Assembly requires two persons. Place all parts of the elliptical in a cleared area and remove the packing

materials. Do not dispose of the packing materials until assembly is completed.

Assembly requires the included tool(s) and your own Phillips screwdriver , adjustable wrench , and rubber mallet .

See the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if

it has been preassembled. To avoid damaging parts, do not use power tools for assembly.

To make assembly easier, read the

nformation on page 5 before you begin.

Remove the two packing inserts from the pack-

ng materials. With the help of another person,

i place the packing inserts under the front of the Frame (1) as shown. Have the other person

hold the elliptical to prevent it from tipping until this step is completed.

Hold the Front Stabilizer (2) under the Frame (1). Attach the Front Stabilizer with four 5/16" x 2 1/2" Button Screws (88).

With the help of the other person, remove the packing inserts and lower the Front Stabilizer (2) and the Frame (1).

2. With the help of another person, place the packing inserts under the rear of the Frame (1) as shown. Have the other person hold the ellip-

tical to prevent it from tipping until this step is completed.

Next, hold the Rear Stabilizer (3) under the Frame (1). Attach the Rear Stabilizer with four 5/16" x 2 1/2" Button Screws (88).

Remove the packing inserts and lower the Rear Stabilizer (3) and the Frame (1).

Packing

Inserts

Packing

Inserts

3. Tip: Avoid pinching the Wire Harnesses (97,

54). Start all screws before tightening any of them.

While a second person holds the Upright (6)

ear the Frame (1), connect the Upper Wire

n Harness (97) to the Lower Wire Harness (54).

Attach the Upright (6) to the Frame (1) with five 5/16" x 1" Patch Screws (81) and five 5/16" Split Washers (105).

void pinching the

Wire Harnesses

(97, 54)

4. Apply a generous amount of the included grease to the Pivot Axle (33) and to two 5/8" Wave Washers (102).

Tip: Avoid pinching the Upper Wire Harness (97). Insert the Pivot Axle (33) through the

Upright (6). Then, slide a 5/8" Wave Washer (102) onto each end of the Pivot Axle.

Slide an Upper Body Arm (12) onto the left side of the Pivot Axle (33). Attach the Upper Body Arm with a 5/16" x 1" Patch Screw (81), a Large Axle Cover (94), and a 5/16" Washer (104).

105

104

102

105

Avoid pinching the Upper Wire

Harness (97)

Grease

102

104

Attach the other Upper Body Arm (12) in the same way.

5. Identify the Right Pedal Plate (107), which is marked with an “R” sticker.

Attach the Right Pedal Plate (107) to the Right Pedal Arm (8) with three M10 x 20mm Patch Screws (108) and three M10 Split Washers

110).

(

110

Repeat this step on the other side of the elliptical.

6. Identify the Right Pedal Assembly (62), which is located in a package marked with a “Right” sticker.

Attach the Right Pedal Assembly (62) to the Right Pedal Plate (107) with five #10 x 1/2" Screws (79), five M6 Split Washers (111), and five #10 Fender Washers (80). Tip: There are

eight holes around the Right Pedal Plate; only five holes will be used. To avoid damaging the Right Pedal Assembly, do not overtighten the Screws.

Repeat this step for the other side of the elliptical.

107

Do not use

these holes

111

7. Identify the Right Link Arm (10), which is marked with a “Right” sticker.

pply a small amount of grease to the two axles

A on the Right Link Arm (10) and to two 5/8"

ave Washers (102). Then, slide a Pivot

W Spacer (71) and a Wave Washer onto each axle.

Gradually work the Right Link Arm (10) into the right Upper Body Arm (12) while at the same time working the Right Link Arm into the Right Pedal Arm (8).

Tip: These parts are designed to fit tightly. It may be helpful to move the Right Pedal Arm (8) while working these parts into place.

Repeat this step for the other side of the elliptical.

Grease

102

Grease

8. Attach the Right Link Arm (10) to the right Upper Body Arm (12) with a 5/16" x 1" Patch Screw (81), a Large Axle Cover (94), and a 5/16" Washer (104).

Then, attach the Right Link Arm (10) to the Right Pedal Arm (8) with a 5/16" x 1" Patch Screw (81), a Small Axle Cover (67), and a 5/16" Washer (104).

Tip: If it is difficult to work the Right Link Arm (10) into the right Upper Body Arm (12) and the Right Pedal Arm (8), try working the Right Link Arm in halfway and then tightening the 5/16" x 1" Patch Screws (81) to pull it in the rest of the way.

Repeat this step for the other side of the elliptical.

104

+ 19 hidden pages