Epic EPEL09950 Owner's Manual
Model No. EPEL0995.0
Serial No. _
Serial
Number
Decal
(beneath
ramp)
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
USER’S MANUAL
CALL TOLL FREE:
1-866-997-6999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.iconservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
HOW TO OPERATE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
IMPORTANT PRECAUTIONS
WARNING:
tions before using the elliptical exerciser.
1. Read all instructions in this manual and all
warnings on the elliptical exerciser before
using the elliptical exerciser. Use the elliptical exercise r only as described.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. The elliptical exerciser is intended for
in-home use only. Do not use the elliptical
exerciser in a commercial, rental, or institutional setting.
4. Place the elliptical exerciser on a level surface, with a mat beneath it to protect the
floor or carpet. Keep the elliptical exerciser
indoors, away from moisture and dust. Make
sure that there is enough clearance around
the elliptical exerciser to mount, dismount,
and use it.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 350 pounds.
To reduce the risk of serious injury, read the following important precau-
8. Always hold the handlebars or the handgrip
pulse sensor when mounting, dismounting,
or using the elliptical exerciser.
9. Wear appropriate exercise clothes and
athletic shoes while using the elliptical
exerciser.
10. Keep your back straight when using the elliptical exerciser; do not arch your back.
11. If you feel pain or dizziness while exercising, stop immediately and cool down.
12. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exerci se aid in determining heart rate
trends in general.
When you stop exercising, allow the pedals
13.
to slowly come to a complete stop. The elliptical exerciser does not have a free wheel;
the pedals will continue to move until the
flywheel stops.
14. Always unplug the power cord immediately
after use and before cleaning the elliptical
exerciser.
WARNING:Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
2
BEFORE YOU BEGIN
Congratulations for selecting the new EPIC E 950
lliptical exerciser. The E 950 elliptical exerciser offers
e
an impressive array of features designed to make
your workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, see the front cover of
this manual. To help us assist you, please note the
product model number and serial number before contacting us. The model number is EPEL0995.0. The
Left Handlebar
Handgrip Pulse Sensor
serial number can be found on a decal attached to the
lliptical exerciser (see the front cover of this manual
e
for the location of the decal).
To avoid a registration fee for any service needed
under warranty, you must register the elliptical
exerciser at www.iconservice.com/registration.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Fans
Console
BACK
Ramp
Water Bottle Holder*
Pedal
Wheel
Pedal Arm
RIGHT SIDE
Power Receptacle
*No water bottle is included
The decals shown above have been placed on the elliptical exerciser. If a decal is missing or illegible, call the toll-free telephone number on the front cover of this manual and order a free replacement decal. Apply the decal in the location shown.
3
ASSEMBLY
M8 Split
Washer
(85)–11
M8 x 25mm
Washer (119)–2
M8 x 18mm
Washer (93)–4
M8 x 20mm Button
Screw (118)–2
M8 x 25mm Button
Screw (100)–1
M8 x 65mm Button Screw (95)–8
M8 x 47mm Button Screw (1 10)–2
M8 x 23mm
Washer (103)–2
Union Set (86)–2
M4 x 16mm
Screw (89)–30
M4 x 16mm Round
Head Screw (91)–6
M8 x 13mm Button
Screw (90)–8
M8 x 16mm Button
Screw (94)–4
M8 x 25mm Patch
Screw (123)–2
To hire an authorized technician to assemble the elliptical exerciser, call toll-free 1-800-445-2480.
ssembly requires two persons.Place all parts of the elliptical exerciser in a cleared area and remove the
A
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the two
included hex keys, assembly requires a phillips screwdriver , two adjustable
wrenches , a rubber mallet , and pliers .
Use the drawings below to identify the small parts used for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST on pages 24 and 25. The number following the key
number is the quantity needed for assembly.
is not in the parts bag, check to see if it has been preassembled.
Note: Some s mal l pa rts may have been preassembled. If a part
1. Orient the Front Stabilizer (3) as shown. Attach the
Front Stabilizer to the Frame (1) with four M8 x 65mm
Button Screws (95) and four M8 Split Washers (85).
Next, attach the Front Shield (38) to the Front
Stabilizer (3) with two M4 x 16mm Round Head
Screws (91).
Then, tighten the two Frame Cushions (106) into the
underside of the Frame (1).
1
91
38
4
1
3
85
95
95
85
106
2. Orient the Rear Stabilizer (2) as shown. Attach the
Rear Stabilizer to the Frame (1) with four M8 x 65mm
utton Screws (95) and four M8 Split Washers (85).
B
2
2
1
85
3. Slide an M8 x 25mm Washer (119) onto an M8 x
20mm Button Screw (118). Tighten the Button Screw
into one end of the Incline Axle (68). Apply a small
amount of the included grease to the Incline
Orient the Ramp (5) so that the opening is up as
shown. Fit the welded tube on the underside of the
Ramp between the two rings on the top of the Frame
(1). Insert the Incline Axle (68) through the rings and
the welded tube.
Slide an M8 x 25mm Washer (119) onto an M8 x
20mm Button Screw (118). Tighten the Button Screw
into the open end of the Incline Axle (68).
4. Using your fingers, turn the shaft on top of the Motor
(46) counterclockwise until it stops turning. Next, fit the
opening of the Ramp (5) over the front of the Frame
(1) as shown. Position the U-bracket on the underside
of the Ramp over the end of the shaft as shown.
Insert the Clevis Pin (112) through one side of the Ubracket on the Ramp (5), an 8mm Plastic Spacer
(111), the shaft on the Motor (46), another 8mm Plastic
Spacer, and the other side of the U-bracket. Then,
insert the straight end of a Hairpin (65) through the
hole in the Clevis Pin.
Axle.
85
95
3
5
119
118
4
5
12
1
46
95
Opening
Grease
1
111
Welded
Tube
119
68
65
118
5
5. Attach a Pedal Assembly (39) to the Left Pedal Arm (9)
with five M4 x 16mm Screws (89).
Attach the other Pedal Assembly (not shown) to the
ight Pedal Arm (not shown) in the same way.
R
5
89
89
39
9
6. Remove the two Pivot Shafts (10) from the two Pivot
Arms (not shown). Next, identify a Union Set (86), and
remove t he scr ew fro m the barrel. Apply a small
amount of grease to the outside of the barrel.
Slide an M8 x 18mm Washer (93), a Wheel Cap (53),
and a 30mm Spacer (87) onto the barrel of the Union
Set (86). While another person aligns the indicated
holes in the Left Pedal Assembly (39), a Pedal Arm
Wheel (52), and a Pivot Shaft (10), insert the barrel
through all of the holes. Then, slide another 30mm
Spacer (87) onto the barrel.
Next, slide an M8 x 18mm Washer (93) and a Wheel
Cap (53) onto the screw of the Union Set (86), and
tighten the screw into the barrel.
Attach the other Pivot Shaft (not shown) and the other
Pedal Arm Wheel (not shown) to the Right Pedal
Assembly (not shown) in the same way.
7. While another person holds the Upright (4) near the
Frame (1), connect the Upper Wire Harness (58) to the
Extension Wire Harness (59). Slide the Upright onto
the top of the Frame, being careful not to pinch the
ire Harnesses
W
Attach the Upright (4) to the Frame (1) with two M8 x
47mm Button Screws (110), an M8 x 25mm Button
Screw (100), and three M8 Split Washers (85).
.
6
86
Grease
7
93
87
53
Align
these
holes
10
86
93
87
53
52
39
Do not pinch the
wire harnesses
during this step.
58
59
85
85
100
10
1
4
1
6
. Identify the Left Pulse Sensor Bar (26) and the Right
8
Pulse Sensor Bar (124); the Pulse Sensor Bars are
arked with stickers. While another person holds the
m
Pulse Sensor Bars near the Upright (4), connect the
upper pulse wires to the lower pulse wires. Insert the
excess wire into the Upright.
Orient the Pulse Sensor Bars (26, 124) as shown.
ttach the Pulse Sensor Bars to the Upright (4) with
A
four M8 x 16mm Button Screws (94),
not to pinch the wires
.
being careful
8
Lower
Pulse Wire
124
Upper
Pulse
Wire
4
26
4
9
Lower
Pulse Wire
94
4
9
Upper
ulse Wire
P
9. Identify the Front Center Pivot Cover (27). Attach the
Front Center Pivot Cover to the Frame (1) with four M4
x 16mm Screws (89).
Next, identify the Rear Center Pivot Cover (28). Attach
the Rear Center Pivot Cover to the Frame (1) with four
M4 x 16mm Screws (89).
10.Apply a small amount of the included high-temperature
lubricant to a paper towel, and rub a thin film of the
lubricant onto both of the Pivot Shafts (10). Next, apply
a small amount of grease to the axle in the Upright (4).
Then, slide a 5mm Spacer (35) onto each end of the
axle in the Upright (4).
Next, slide the two Pivot Arms (20) onto the Pivot
Shafts (10), and turn the Pivot Arms so the flanges are
facing away from the elliptical exerciser. Then, slide
the Pivot Arms onto the ends of the axle in the Upright
(4); use a rubber mallet, if necessary.
Slide an M8 x 23mm Washer (103) onto an M8 x
25mm Patch Screw (123). Attach the left Pivot Arm
(20) to the left end of the axle with the Patch Screw.
Attach the right Pivot
axle in the same way.
Arm (20) to the right end of the
9
89
10
123
28
Flange
103
20
Lubricate
4
4
Grease
35
89
10
89
89
27
Grease
20
10
7
11.Identify the Left Handlebar (7). Attach the Left
Handlebar to the left Pivot Arm (20) with four M8 x
13mm Button Screws (90) as shown.
Attach the Right Handlebar (6) to the right Pivot Arm
(20) in the same way.
1
1
Attach the Water Bottle Holder (23) to the Upright (4)
with two M4 x 16mm Screws (89).
12.Position the Front Left Pivot Cover (21) and the Rear
Left Pivot Cover (31) over the left Pivot Arm (20) as
shown. Attach the Left Pivot Covers with an M4 x
16mm Round Head Screw (91) and two M4 x 16mm
Screws (89).
Attach the Front Right Pivot Cover (29) and the Rear
Right Pivot Cover (not shown) over the right Pivot Arm
(not shown) in the same way.
12
91
89
90
7
6
20
23
20
90
4
31
29
20
89
21
89
13. While another person holds the Console (17) near the
Upright (4), attach the Upper Wire Harness (58) and
the Pulse Sensor Wire (25) to the corresponding console wire harnesses. Then, attach the Console to the
Upright with six M4 x 16mm Screws (89), being care-
ful not to pinch the wires.
Attach the Upright Cover (22) to the Upright (4) with
two M4 x 16mm Round Head Screws (91).
14. Plug the Power Cord (56) into the Power Receptacle
(70) at the rear of the elliptical exerciser.
15.Make sure that all parts of the elliptical exerciser are properly tightened.
the assembly of your elliptical exerciser, activate the calibration process by following the steps in
HOW T
to protect the floor from damage. Note: Some extra hardware may be left over
O CALIBRATE THE INCLINE SYSTEM on page 17.
13
91
89
89
14
Cover the floor beneath the elliptical exerciser
22
25
58
4
70
56
When you have completed
.
17
8
Loading...