Enttec ODE MK2 Users Manual
User Manual
ODE Mk2 MANUAL
For latest version visit:
www.enttec.com
May 18 ID: 3275345 Rev:33 Page|1
ODE MK2
Box Contents
• ODE Mk2 (PN: 70405 or 70406)
• Straight connect Ethernet lead (PN: 79102)
• Power Adapter (PN: 79111) if you have the POE
option, the power adapter is not included.
• This user manual
Features
• 1 Universe Ethernet to DMX node (Output mode)
• 1 Universe DMX to Ethernet (Input mode)
• Easy to setup & update through any web
browser
• Supports following DMX over Ethernet proto-
cols:
o Art-Net
o Streaming ACN (sACN)
o ESP
• Supports RDM over Art-Net (controller)
• Supports Art-Net 3
• HTP/LTP Merging support: up-to 2 DMX sources
can be merged (if enabled).
• 1 RJ45 connector (10/100 Mbps)
• Static or Dynamic (DHCP) IP configuration (DHCP
by default)
• Supports IEEE 802.3af PoE (Power over Ethernet)
over RJ45 connector (only on PoE model PN 70406)
• Supports Broadcast or Unicast (Input mode)
• 5Pin DMX XLR connectors
Safety
• Do not expose the ODE Mk2 to rain or moisture,
doing this will void the warranty
• This unit is intended for indoor use only
Basic Setup
Right out of the box, the ODE Mk2 is factory configured to be
a DMX OUTPUT device, listening to the first Art-Net Universe
(0x00). It is also set as a DHCP node, so you can plug it into
your existing router, and it's good to go.
To make any changes to the configuration, you will need the
IP address of ODE Mk2.
If you connect ODE to a network router, it will be assigned
an IP address as per the router’s DHCP addressing. However,
if you connect ODE to a switch or a computer, it will use the
factory set static IP address (printed on the box).
ENTTEC provides a free App (available for Windows and Mac)
called NMU, which will find the ODE on your network and
display its IP address.
Using the IP address one can access the built-in web-interface inside the ODE via any modern web-browser. The webinterface allows the settings of the unit to be changed.
User Manual
ODE Mk2 MANUAL
For latest version visit:
www.enttec.com
May 18 ID: 3275345 Rev:33 Page|2
Once setup, any Art-Net/sACN/ESP enabled software/app or a lighting control/desk can be used to send
DMX out of the ODE. For a list of recommended apps,
please check the website www.enttec.com/ode
LED Status
The ODE Mk2 comes with four LED indicators located
between the DC power jack and the RJ45 connector.
1. STAT (Status): Blinks to indicate the following:
Frequency
Status
0.5 Hz
Normal
1 Hz
DMX Port Receive
2 Hz
DMX Port Send
Always on
Error
25 Hz
Control 4 Identify
2. DIR (Port Direction): The LED will be ON when
the DMX port is in Output mode, and OFF when
the DMX port is in input mode.
3. LINK: This LED will be ON when there is an
Ethernet Link.
4. ACT: This LED blinks when there is activity on the
Ethernet network.
NMU
NMU (Node Management Utility) is a free Windows and Mac
application that is used to manage compatible ENTTEC
DMX over Ethernet nodes.
NMU will help you find your unit's IP address and then
open a browser window to access the web-interface.
Please follow these steps:
1. Download NMU from www.enttec.com/nmu
2. Ensure that your ODE Mk2 is hooked up physically
by an Ethernet cable.
3. And connected to the same physical network (or
router) as the computer on which you will run
NMU.
4. Open NMU. If prompted with multiple networks,
select the correct network. (identified by the IP address of your computer on that network)
5. Press the Discovery button, and wait till NMU finds
all supported ENTTEC devices on your network.
Loading...