Page 1
Page 2
Table of Contents
Chapter 1 ........................................................................................................................................................................................ 5
Key Features ............................................................................................................................................................................................ 6
Introduction .............................................................................................................................................................................................. 7
System Requirements ............................................................................................................................................................................... 8
Package Contents ..................................................................................................................................................................................... 8
Applications ............................................................................................................................................................................................. 9
Technical Specifications ........................................................................................................................................................................ 10
Physical Interface ................................................................................................................................................................................... 12
Chapter 2 ...................................................................................................................................................................................... 13
Considerations for Wireless Installation ................................................................................................................................................ 14
Computer Settings .................................................................................................................................................................................. 15
Hardware Installation ............................................................................................................................................................................. 19
Mounting the Access Point .................................................................................................................................................................... 20
Connecting using the 110 Punch-down Block ....................................................................................................................................... 22
Chapter 3 ...................................................................................................................................................................................... 23
Default Settings ...................................................................................................................................................................................... 24
Web Configuration ................................................................................................................................................................................. 25
Chapter 4 ...................................................................................................................................................................................... 27
Device Status .......................................................................................................................................................................................... 28
Connections ............................................................................................................................................................................................ 31
Chapter 5 ...................................................................................................................................................................................... 32
IPv4 Settings .......................................................................................................................................................................................... 33
IPv6 Settings .......................................................................................................................................................................................... 34
Spanning Tree Settings........................................................................................................................................................................... 35
Page 3
LAN Port Settings .................................................................................................................................................................................. 36
Chapter 6 ...................................................................................................................................................................................... 37
2.4GHz SSID Profile.............................................................................................................................................................................. 38
Wireless Security ................................................................................................................................................................................... 39
Wireless MAC Filter .............................................................................................................................................................................. 42
Traffic Shaping ....................................................................................................................................................................................... 43
Guest Network ....................................................................................................................................................................................... 44
RSSI Threshold ...................................................................................................................................................................................... 46
Management VLAN Settings ................................................................................................................................................................. 47
Chapter 7 ...................................................................................................................................................................................... 48
SNMP Settings ....................................................................................................................................................................................... 49
CLI/SSH Settings ................................................................................................................................................................................... 51
HTTPS Settings...................................................................................................................................................................................... 52
Email Alert ............................................................................................................................................................................................. 53
Date and Time Settings .......................................................................................................................................................................... 54
WiFi Scheduler ....................................................................................................................................................................................... 55
Tools ....................................................................................................................................................................................................... 57
LED Control ........................................................................................................................................................................................... 60
Device Discovery ................................................................................................................................................................................... 60
Chapter 8 ...................................................................................................................................................................................... 61
Account Setting ...................................................................................................................................................................................... 62
Firmware Upgrade ................................................................................................................................................................................. 63
Backup/Restore ...................................................................................................................................................................................... 64
System Log ............................................................................................................................................................................................ 65
Reset ....................................................................................................................................................................................................... 66
Logout .................................................................................................................................................................................................... 67
Appendix ...................................................................................................................................................................................... 68
Page 4
Appendix A - FCC Interference Statement ............................................................................................................................................ 69
Appendix B - CE Interference Statement............................................................................................................................................... 71
Page 5
Chapter 1
Product Overview
Page 6
Introduction
Key Features
Deploy and manage with ease using EWS Series Wireless Management Switches.
Integrated 802.11n wireless access point and 4 port Ethernet switch
Gigabit Ethernet uplink provides high speed Internet access
4 x 10/100Mbps Ethernet port for wired device connectivity (1 port includes PoE output)
Additional RJ45 pass-through port for connecting to phone systems
Powered by 802.11af/at Power over Ethernet or 48VDC adapter
Internal high-performance antennas for low profile design
Effective and flexible bandwidth management
Secure Guest Network option available
Ideal for audio, video and voice application
Mounts onto any standard wall box
Page 7
Introduction
This device is an enhanced-powered, long-range wireless access point. It is designed to operate in numerous environments; from large
homes, small and medium-sized businesses, multiple-floor offices, hotels, and other venues, to larger enterprise deployments. Its
enhanced-powered, long-range characteristics make it a cost-effective alternative to ordinary Access Points that don’t have the range
and reach to connect to a growing number of wireless users who wish to connect to a large hotspot or business network.
To protect sensitive data during wireless transmissions, the device offers different encryption settings for wireless transmissions,
including industry standard WPA and WPA2 encryption. The device also includes MAC address filtering to allow network
administrators to offer network access only to known computers and other devices based on their MAC addresses.
Page 8
System Requirements
The following are the Minimum System Requirements in order to configure the device:
Computer with an Ethernet interface or wireless network capability
Windows OS (XP, Vista, 7, 8), or Mac OS
Web-Browsing Application (i.e. Internet Explorer, Firefox, Chrome, Safari, or another similar browser application)
Package Contents
The package contains the following items (all items must be in package to issue a refund):
EWS Wall Plate Access Point
Mounting Bracket
Bracket Screw
Quick Installation Guide
Page 9
Applications
Wireless LAN (WLAN) products are easy to install and highly efficient. The following list describes some of the many applications
made possible through the power and flexibility of WLANs:
Difficult-to-Wire Environments: There are many situations where wires cannot be installed, deployed easily, or cannot be
hidden from view. Older buildings, sites with multiple buildings, and/or areas that make the installation of a Ethernet-based
LAN impossible, impractical or expensive are sites where WLAN can be a network solution.
Temporary Workgroups: Create temporary workgroups/networks in more open areas within a building; auditoriums,
amphitheaters classrooms, ballrooms, arenas, exhibition centers, or temporary offices where one wants either a permanent or
temporary Wireless LAN established.
The Ability to Access Real-Time Information: Doctors/Nurses, Point-of-Sale Employees, and/or Warehouse Workers can access
real-time information while dealing with patients, serving customers, and/or processing information.
Frequently Changing Environments: Set up networks in environments that change frequently (i.e.: Show Rooms, Exhibits, etc.).
Small Office and Home Office (SOHO) Networks: SOHO users require a cost-effective, easy, and quick installation of a small
network.
Training/Educational Facilities: Training sites at corporations or students at universities use wireless connectivity to exchange
information between peers and easily access information for learning purposes.
Page 10
Technical Specifications
Page 11
Page 12
Physical Interface
1. LED Indicators: LEDs for Power, WAN, 2.4Hz , LAN 1~4
2. Reset Button: Press and hold for over 10 seconds to reset to factory default settings.
3. 10/100 LAN Ports: Three RJ45 access ports
4. 10/100 LAN Port (PoE Out): RJ45 access port with PoE Out (support 802.3af output when PoE input is 802.3at)
5. RJ45 Pass Through Port: Pass through port
6. DC48V Input: DC48V/0.8A power in
7. 10/100/1000 RJ45 Uplink (PoE In): Uplink port that supports 802.3af/at PoE input
8. 110 Punch Down Block
Page 13
Chapter 2
Before You Begin
Page 14
Before You Begin
This section will guide you through the installation process. Placement of the EnGenius Access Point is essential to maximize the
Access Point’s performance. Avoid placing the Access Point in an enclosed space such as a closet, cabinet, or stairwell.
Considerations for Wireless Installation
The operating distance of all wireless devices can often not be pre -determined due to a number of unknow n obstacles in
the environment in which the device is deployed. Obstacles such as the number, thickness, and location of walls, ceilings,
or other objects that the Access Point’s wireless signals must pass through can weaken the signal. Here are some key
guidelines for allowing the Access Point to have an optimal wireless range during setup.
Keep the number of walls and/or ceilings between the Access Point and other network devices to a minimum. Each wall and/or
ceiling can reduce the signal strength, resulting in a lower overall signal strength.
Building materials make a difference. A solid metal door and/or aluminum stubs may have a significant negative effect on the
signal strength of the Access Point. Locate your wireless devices carefully so the signal can pass through drywall and/or open
doorways. Materials such as glass, steel, metal, concrete, water (example: fish tanks), mirrors, file cabinets, and/or brick can
also diminish wireless signal strength.
Interference from your other electrical devices and/or appliances that generate RF noise can also diminish the Access Point’s
signal strength. The most common types of devices are microwaves or cordless phones.
Page 15
Computer Settings
Windows XP/Windows 7
In order to use the Access Point, you must first configure the TCP/IPv4 connection of your Windows OS computer system.
1. Click the
2a. In
Windows XP
button and open the
Start
Windows XP Windows 7
, click on Network Connections.
Control Panel
.
Page 16
2b. In
Windows 7
, click
View network status and tasks
in the
Network and Internet
section, then select
Change adapter
settings.
3. Right click on
Local Area Connection
and select
Properties
.
4. Select
Internet Protocol Version 4 (TCP/IPv4)
and then select
Properties
.
Page 17
5. Select
Access Point and Subnet mask, then click OK.
Note
device.
For example: Access Point IP address: 192.168.1.1
Use the following IP address
: Ensure that the IP address and Subnet mask are on the same subnet as the
PC IP address: 192.168.1.2 – 192.168.1.255
PC Subnet mask: 255.255.255.0
and enter an IP address that is different from the
Page 18
Apple Mac OS X
1. Go to
2. Select
3. Highlight
4. In
System Preferences
Network
Configure IPv4
in the
Ethernet
(it can be opened in the
Internet & Network
.
, select
Manually
Applications
section.
.
folder or by selecting it in the Apple Menu).
5. Enter an IP address that is different from the Access Point and
Subnet mask, then click OK.
Note: Ensure that the IP address and Subnet mask are on the same
subnet as the device.
For example: Access Point IP address: 192.168.1.1
PC IP address: 192.168.1.2 – 192.168.1.255
PC Subnet mask: 255.255.255.0
6. Click
Apply
when finished.
Page 19
Hardware Installation
1. Connect one end of a RJ45 Ethernet cable to the
2. Connect the other end of the RJ45 Ethernet cable to a
3. Using another RJ45 Ethernet cable, connect one end to the
another port on the
4. Provide power to the PoE injector/switch.
5. Verify that the
6. Proceed to set up the Access Point using the computer.
PoE Ethernet switch
Power LED
on the AP is steady
or to the
PoE In (LAN/Uplink) port
PoE Ethernet switch
Data In port
orange
.
Ethernet port
on the PoE injector.
on the rear of the Access Point.
or the
on the computer, and connect the other end to
PoE Out port
on the
PoE injector
.
Page 20
Mounting the Access Point
The EWS Wall Plate AP is designed to be mounted on an electrical outlet box.
1. Remove the cover from the outlet box, retaining the original cover screws.
2. Gently pull the required cables through the center of the mounting bracket.
3. Align the mounting bracket with the outlet box and affix the mounting bracket to the outlet box using the original cover
screws.
Page 21
4. Connect the cables to the access point before mounting it to the bracket.
5. Hook the two tabs on the bottom of the bracket into the slots on the bottom of the AP and slide the AP down gently until it
holds in place.
6. Use the bracket screw provided to secure the AP to the bracket.
Page 22
Connecting using the 110 Punch-down Block
The 110 punch-down block can be used to connect the AP to the network instead of the RJ45 connector.
Page 23
Chapter 3
Configuring Your Access Point
Page 24
Configuring Your Access Point
IP Address
192.168.1.1
Username/Password
admin/admin
This section will show you how to configure the device using the web-based configuration interface.
Default Settings
Please use your Ethernet port or wireless network adapter to connect the Access Point.
Page 25
Web Configuration
1. Open a web browser (Internet Explorer/Firefox/Safari) and enter the IP Address http://192.168.1.1.
: If you have changed the default LAN IP Address of the Access Point, ensure you enter the correct IP Address.
Note
2. The default username and password are:
admin
. Once you have entered the correct username and password, click the
button to open the web-based configuration page.
3. If successful, you will be logged in and see the Access Point User Interface.
*Model name varies depending on model.
Login
Page 26
Page 27
Chapter 4
Overview
Page 28
Overview
The
Overview
• Device Status
• Connections
The following sections describe these options.
section contains the following options:
Device Status
Clicking the
The
Device Information
Firmware Version, and Management VLAN ID
Device Status
link under the
section shows general system information such as Device Name, MAC address, Current Time,
Overview
menu shows the status information about the current operating mode.
The
LAN Information
DNS Address, DHCP Client, and STP status.
section shows the Local Area Network settings such as the LAN IP Address, Subnet mask, Gateway,
Page 29
The
Wirelesss LAN Information 2.4 GHz
Channel. Since the Access Point supports multiple-SSIDs, information about each SSID and security settings are displayed.
section shows wireless information such as Operating Mode, Frequency, and
Page 30
Page 31
Connections
Clicking the
along with the MAC address, TX, RX and signal strength for each client. Clicking
Click
Refresh
Connections
to refresh the Connection List page.
link under the
Device Status
menu displays the list of clients associated to the Access Point’s 2.4GHz,
in the Block column removes this client.
Kick
Page 32
Chapter 5
Network
Page 33
Basic
This page allows you to modify the device’s IP settings and the Spanning Tree settings. Enabling Spanning Tree protocol will
prevent network loops in your LAN network.
IPv4 Settings
IP Network Setting
obtained automatically when the device connects to a DHCP server.
IP Address
IP Subnet Mask
Gateway
Primary/Secondary DNS
: The IP Address of this device.
: The Default Gateway of this device. Leave it blank if you are unsure of this setting.
: Select whether the device IP address will use the static IP address specified in the IP Address field or be
: The IP Subnet mask of this device.
: The primary/secondary DNS address for this device.
Page 34
IPv6 Settings
Link-Local Address
IP Address
Subnet Prefix Length
Gateway
Primary / Secondary DNS
: The IPv6 IP Address of this device.
: The IPv6 Default Gateway of this device. Leave it blank if you are unsure of this setting.
: Check this if you want to use Link-Local Address.
: The IPv6 Subnet Prefix Length of this device.
: The primary / secondary DNS address for this device.
Page 35
Spanning Tree Settings
Status
Hello Time
communicate information about the topology throughout the entire Bridged Local Area Network.
Max Age
of time, it is assumed to be inactive.
Forward Delay
Learning states before the Forwarding state is entered. This delay is provided so that when a new bridge comes onto a busy
network, it analyzes data traffic before participating.
Priority
Save
: Enables or disables the Spanning Tree function.
: Specify Bridge Hello Time, in seconds. This value determines how often the device sends handshake packets to
: Specify Bridge Max Age, in seconds. If another bridge in the spanning tree does not send a hello packet for a long period
: Specifies Bridge Forward Delay, in seconds. Forwarding Delay Time is the time spent in each of the Listening and
: Specify the Priority Number. A smaller number has greater priority.
: Click Save to confirm the changes.
Page 36
LAN Port Settings
Enable Port
access through the AP, uncheck box next to the corresponding LAN port.
VLAN
VLAN ID
: Check this box to enable VLAN for the LAN port.
: All Ethernet ports are enabled by default. Unchecking this box disables that port. If you do not want to provide wired
: Enter a VLAN ID to segment traffic arriving on this port to a specific VLAN.
Page 37
Chapter 6
2.4GHz Wireless
Page 38
Basic
2.4GHz SSID Profile
Under
to.
Enable:
Wireless Settings
, you can edit the SSID profile to fit your needs. Click
Check this option to enable this profile.
under the SSID you would like to make changes
Edit
Specifies the SSID for the current profile.
SSID:
Security:
section.
Hidden SSID:
Client Isolation:
VLAN Isolation:
VLAN ID:
Displays the Security Mode the SSID uses. You can click
Check this option to hide the SSID from clients. If checked, the SSID will not appear in the site survey.
Check this option to prevent communication between client devices.
Check this option to enable VLAN Isolation feature.
Specifies the VLAN ID for the SSID profile.
to change the security mode. For more details, see the next
Edit
Page 39
Wireless Security
The Wireless Security section lets you configure the Access Point’s security modes: WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed,
WPA-Enterprise, WPA2-Enterprise and WPA Mixed Enterprise.
It is strongly recommended that you use
the security settings.
WEP
Auth Type:
Input Type:
Select Open System or Shared Key.
ASCII: Regular Text (Recommended) or HEX: Hexadecimal Numbers (For advanced users).
WPA2-PSK
. Click on the
button under Wireless Settings next to the SSID to change
Edit
Key Length:
password lengths.
Default Key:
are for decryption only. You must enter a Key Value for the Default Key.
Encryption Key:
Select the desired option and ensure the wireless clients use the same setting. Your choices are: 64, 128, and 152-bit
Select the key you wish to be default. Transmitted data is ALWAYS encrypted using the Default Key; the other Keys
Enter the Key Value or values you wish to use. The default is none.
Page 40
WPA-PSK/WPA2-PSK (Pre-Shared Key)
Encryption:
Protocol) and AES(Advanced Encryption Standard). Please ensure that your wireless clients use the same settings.
Passphrase:
characters in length. If using HEX format, the Key must be 64 HEX characters in length.
Group Key Update Interval:
Select the WPA/WPA2 encryption type you would like to use. Available options are Both, TKIP(Temporal Key Integrity
Wireless clients must use the same Key to associate the device. If using ASCII format, the Key must be from 8 to 63
Specify how often, in seconds, the Group Key changes.
WPA/WPA2-Enterprise
Encryption:
Select the WPA/WPA2 encryption type you would like to use. Available options are Both, TKIP(Temporal Key Integrity
Page 41
Protocol) and AES(Advanced Encryption Standard). Please ensure that your wireless clients use the same settings.
Group Key Update Interval:
Radius Server:
Radius Port:
Radius Secret:
Radius Accounting:
Radius Accounting Server:
Radius Accounting Port:
Radius Accounting Secret:
Interim Accounting Interval:
Note:
from 802.11n to 802.11g.
802.11n does not allow WEP/WPA-PSK TKIP/WPA2-PSK TKIP security mode. The connection mode will automatically change
Enter the IP address of the Radius server.
Enter the port number used for connections to the Radius server.
Enter the secret required to connect to the Radius server.
Enables or disables the accounting feature.
Enter the IP address of the Radius accounting server.
Enter the port number used for connections to the Radius accounting server.
Enter the secret required to connect to the Radius accounting server.
Specify how often, in seconds, the group key changes.
Specify how often, in seconds, the accounting data sends.
Page 42
Wireless MAC Filter
Wireless MAC Filter is used to allow or deny network access to wireless clients (computers, tablet PCs, NAS, smart phones, etc.)
according to their MAC addresses. You can manually add a MAC address to restrict permission to access the Access Point. The
default setting is: Disable Wireless MAC Filter.
ACL (Access Control List) Mode:
in the MAC address table on this page. Choices given are: Disabled, Deny MAC in the list, or Allow MAC in the list.
MAC Address:
Click
Add:
Delete:
Deletes the selected entries.
Enter the MAC address of the wireless client.
to add the MAC address to the MAC Address table.
Add
Determines whether network access is granted or denied to clients whose MAC addresses appear
Page 43
Traffic Shaping
Traffic Shaping regulates the flow of packets leaving an interface to deliver improved Quality of Service.
Enable Traffic Shaping:
Download Limit:
Upload Limit:
Save:
Click
Save
Specifies the wireless transmission speed used for downloading.
Specifies the wireless transmission speed used for uploading.
to apply the changes.
Select to Enable or Disable Wireless Traffic Shaping.
Page 44
Guest Network
The Guest Network function allows administrators to grant Internet connectivity to visitors or guests while keeping other
networked devices (computers and hard drives) and sensitive personal or company information private and secure.
Enable SSID:
Specify the SSID for the current profile. This is the name visible on the network to wireless clients.
SSID:
Security:
Hidden SSID:
SSID.
Client Isolation:
wireless devices connected to the AP.
Select to Enable or Disable SSID broadcasting.
You can use None or WPA-PSK / WPA2-PSK security for this guest network.
Check this option to hide the SSID from broadcasting to discourage wireless users from connecting to a particular
Check this option to prevent wireless clients associated with your access point to communicate with other
Page 45
After enabling Guest Network in the SSID Config page, assign an IP Address, Subnet Mask and DHCP server IP address range for
this Guest Network.
Manual IP Settings
IP Address:
Subnet Mask:
Automatic DHCP Server Settings
Starting IP Address:
Ending IP Address:
WINS Server IP:
Microsoft's implementation of NetBIOS Name Service (NBNS), a name server and service for NetBIOS computer names.
Specify an IP Address for the Guest Network
Specify the the Subnet Mask IP Address for the Guest Network
Specify the starting IP Address range for the Guest Network.
Specify the ending IP Address range for the Guest Network.
Specify the WINS Server IP Address for the Guest Network. WINS means Windows Internet Name Service. It is
Page 46
RSSI Threshold
With RSSI Threshold enabled, the AP will send a disassociation request to the wireless client and let it find another AP to
handover and associate upon detecting the wireless client’s RSSI value lower than specified. The RSSI value can be adjusted to
allow more clients to stay associated to this AP. Note that setting the RSSI value too low may cause wireless clients to
reconnect frequently.
Page 47
Management VLAN Settings
This section allows you to assign a VLAN tag to the packets. A VLAN is a group of computers on a network whose software has
been configured so that they behave as if they were on a separate Local Area Network (LAN). Computers on VLAN do not have
to be physically located next to one another on the LAN.
Status:
the VLAN ID. Otherwise, click
Save:
Note:
server supports the reconfigured VLAN ID and then reconnect to the Access Point using the new IP address.
If your network includes VLANs and if tagged packets need to pass through the Access Point, select
Disable
Click
If you reconfigure the Management VLAN ID, you may lose your connection to the Access Point. Verify that the DHCP
to apply the changes.
Save
.
Enable
and enter
Page 48
Chapter 7
Management
Page 49
SNMP Settings
This page allows you to assign the Contact Details, Location, Community Name, and Trap Settings for Simple Network Management
Protocol (SNMP). This is a networking management protocol used to monitor network attached devices. SNMP allows messages (called
protocol data units) to be sent to various parts of the network. Upon receiving these messages, SNMP compatible devices (called agents)
returns the data stored in their Management Information Bases. To configure SNMP Settings, click under the
bar under
Management
.
Advanced
tab on the side
Status:
Contact:
Enables or Disables the SNMP feature.
Specifies the contact details of the device.
Page 50
Location:
Port:
Specifies the location of the device.
Displays the port number.
Community Name (Read Only):
Community Name (Read/Write):
Trap Destination Address:
Trap Destination Community Name:
SNMPv3 Status:
User Name:
Auth Protocol:
Auth Key:
Priv Protocol:
Priv Key:
Engine ID:
Specify the Authentication Key for authentication.
Specifies the privacy key for privacy.
Specifies the Engine ID for SNMPv3.
Enables or Disables the SNMPv3 feature.
Specifies the username for the SNMPv3.feature
Select the Authentication Protocol type: MDS or SHA.
Select the Privacy Protocol type: DES.
Specifies the password for the SNMP community for read only access.
Specifies the password for the SNMP community with read/write access.
Specifies the port and IP address of the computer that will receive the SNMP traps.
Specifies the password for the SNMP trap community.
Page 51
CLI/SSH Settings
Most users will configure the device through the graphical user interface (GUI). However, for those who prefer an alternative
method there is the command line interface (CLI). The CLI can be access through a command console, modem or Telnet connection.
For security’s concern, you can enable SSH (Secure Shell) to establish a secure data communication.
CLI Status:
SSH Status:
with a secure channel.
Select
Select
Enable
Enable
or
Disable
or
Disable
to enable or disable the ability to modify the Access Point via a command line interface (CLI).
to enable or disable the ability to modify the Access Point via a command line interface (CLI)
Page 52
HTTPS Settings
Hypertext Transfer Protocol Secure (HTTPS) is a communications protocol for secure communication over a computer network, with
especially wide deployment on the Internet. Technically, it is not a protocol in and of itself; rather, it is the result of simply layering
the Hypertext Transfer Protocol (HTTP) on top of the SSL/TLS protocol, thus adding the security capabilities of SSL/TLS to standard
HTTP communications.
Status:
HTTPS forward:
Select
Enable
or
Disable
Enable this option; it will be forwarded to HTTPS if user uses HTTP to access the Access Point.
to enable or disable the ability to modify the Access Point via a HTTPS.
Page 53
Email Alert
The Access Point will send email alerts when configurations have been changed.
Status:
From:
To:
Subject:
Email Account
Username/Password:
SMTP Server/Port:
Security Mode
Send Test Mail:
Apply:
Check
Enter the address to show as the sender of the email.
Enter the address to show as the receiver of the email.
Click
Enable
Enter the subject to show as the subject of the email.
: Select the mode of security for the Email alert. The options are None, SSL/TLS and STARTTLS.
Apply
to enable Email Alert feature.
Enter the username and password required to connect to the SMTP server.
Enter the IP address/domain name and port of the SMTP server. The default port of SMTP Server is port 25.
Click
Send Test Mail
to save the changes.
button to test the Email Alert setup.
Page 54
Date and Time Settings
This page allows you to set the internal clock of the Access Point. To access the Date and Time settings, click
under the
Management
tab on the side bar.
Time Zone
Manually Set Date and Time:
Synchronize with PC:
Automatically Get Date and Time:
internal clock set automatically.
Time Zone:
Enable Daylight Savings:
dates that correspond to the present year’s daylight savings time.
Click
Apply
Choose the time zone you would like to use from the drop-down list.
to save the changes.
Click to synchronize the Access Point’s internal clock with the computer’s time.
Manually specify the date and time.
Enter the IP address of an NTP server or use the default NTP server to have the
Check the box to enable or disable daylight savings time for the Access Point. Next, enter the
Page 55
WiFi Scheduler
Use the schedule function to reboot the Access Point or control the wireless availability on a routine basis. The Schedule
function relies on the GMT time setting acquired from a network time protocol (NTP) server. For details on how to connect
the Access Point to an NTP server, see Date and Time Settings.
Auto Reboot Settings
You can specify how often you would like to reboot the Access Point.
Status:
Timer:
Enables or disables the Auto Reboot function.
Specifies the time and frequency in rebooting the Access Point by Min, Hour and Day.
Page 56
WiFi Scheduler
Status:
Wireless Radio:
SSID Selection:
Schedule Templates:
weekends. Select Custom schedule if you want to set the schedule manually.
Schedule Table:
Enables or disables the WiFi Scheduler function.
Select 2.4GHz to use WiFi Schedule.
Select a SSID to use WiFi Schedule.
There are 3 templates available: Always available, Available 8-5 daily and Available 8-5 daily except
Set the schedule manually.
Page 57
Tools
This section allows you to analyze the connection quality of the Access Point and trace the routing table to a target in the
network.
Ping Test Parameters
Target IP/Domain Name:
Ping Packet Size:
Number of Pings:
Start:
Click
Start
Enter the packet size of each ping.
Enter the number of times you wish to ping.
to begin pinging target device (via IP).
Enter the IP address or Domain name you would like to search.
Page 58
Traceroute Parameters
Target IP/Domain Name:
Start:
Stop:
Click
Halts the traceroute test.
Start
to begin the trace route operation.
Enter an IP address or domain name you wish to trace.
Page 59
Speed Test Parameters
Target IP/Domain Name:
Time Period
Start
IPv4 / IPv6 Port:
: Starts the Speed Test.
: Enter the time in seconds that you would like the test to run for and in how many intervals.
The Access Point uses IPv4 port 5001 and IPv6 port 5002 for the speed test.
Enter an IP address or domain name you wish to run a Speed Test for.
Page 60
LED Control
This section allows you to control the LED control functions: Power status, LAN interface and 2.4GHz WLAN interface.
Click
Apply
to save the settings after selecting your choices from the boxes.
Device Discovery
Under Device Discovery, you can choose for the Access Point to automatically scan for local devices to connect to. Click
begin the process.
Scan
to
Page 61
Chapter 8
System Manager
Page 62
Account Setting
This page allows you to change the username and password of the device. By default, the username is
admin
. The password can contain from 0 to 12 alphanumeric characters and is case sensitive.
Administrator Username:
Current Password:
New Password:
Verify Password:
Apply:
Click
Apply
Enter the old password for logging in to the Current Password entry box.
Enter the new password for logging in to the New Password entry box.
Re-enter the new password in the Verify Password entry box for confirmation.
to save the changes.
Enter a new username for logging in to the Administrator Username entry box.
admin
and the password is
Note:
it is highly recommended that you change your password to something more unique for greater security.
Page 63
Firmware Upgrade
This page allows you to upgrade the Firmware of the Access Point.
To Perform the Firmware Upgrade:
1. Click the
2. Select the upgrade file. The name of the file will appear in the Upgrade File field.
3. Click the
Note:
to or through the device will be lost.
Browse…
Upload
The device is unavailable during the upgrade process and must restart when the upgrade is completed. Any connections
button and navigate the OS File System to the location of the Firmware upgrade file.
button to commence the Firmware upgrade.
Page 64
Backup/Restore
This page allows you to save the current device configurations. When you save the configurations, you can also reload the
saved configurations into the device through the
if you have set the Access Point incorrectly, you can use the
the configurations of the Access Point to the original default settings. To Configure the Backup/Restore Settings, click
Firmware
under the
Systems Manager
tab.
Restore New Settings
Reset
button in the
from a file folder. If extreme problems occur, or
Reset to Default
section to restore all
Factory Setting
Backup Setting:
Restore New Setting:
Click
Export
Choose the file you wish restore for settings and click
to save the current device configurations to a file.
Import
.
Reset to Default:
Click the
User Setting
Back Up Setting as Default:
Restore to User Default:
Click
Reset
Click
Restore
button to restore the Access Point to its factory default settings.
Backup
to backup the user settings you would like to use as the default settings.
to restore the Access Point to user’s default settings.
Page 65
System Log
This page allows you to setup the System Log and local log functions of the Access Point. Click
Manager
tab to open up the System Log page.
under the
Log
Systems
Status:
Log Type:
Remote Log:
remote to.
Log Server IP Address:
Apply:
Enables or disables the System Log function.
Select the Log Type mode you would like to use.
Enables or disables the Remote Log feature. If enabled, enter the IP address of the Log you would like to
Click
Apply
to save the changes.
Enter the IP address of the log server.
Page 66
Reset
In some circumstances, you may be required to force the device to reboot. Click on
Reboot the Device
to reboot the device.
Page 67
Logout
Click
Logout
, it will pop up a warning window. Click OK to logout.
Page 68
Appendix
Page 69
Appendix A - FCC Interference Statement
Federal Communication Commission Interference Statement
FCC Caution:
Page 70
IMPORTANT NOTE:
FCC Radiation Exposure Statement
Page 71
Appendix B - CE Interference Statement
Page 72
0560
Česky [Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a
dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk [Danish]
Undertegnede [fabrikantens navn] erklæ rer herved, at følgende udstyr [udstyrets typebetegnelse]
overholder de væ sentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch [German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Ü bereinstimmung mit den
grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie
1999/5/EG befindet.
Eesti [Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of
equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele
asjakohastele sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Español [Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva
1999/5/CE.
Ελληνική [Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ
ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ
1999/5/ΕΚ.
Français [French]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano [Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Page 73
Latviski [Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips]
atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių [Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
Nederlands [Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met
de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar [Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski [Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami
oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português [Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos
essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko [Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi
določili direktive 1999/5/ES.
Slovensky [Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.
Suomi [Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä]
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden
ehtojen mukainen.
Svenska [Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Loading...