EnGenius Technologies ENSTA5 User Manual
CONVENTIONS
N/A:
Prerequisite:
CAUTION!
WARNING!
Important:
Note:
Example:
Conventions
The following conventions are used to give the user additional
information about specific procedures or content. It is important
to pay attention to these conventions as they provide information to prevent damage to equipment or personal injury.
Indicates information used to demonstrate or explain an
associated concept.
General Conventions
The following general conventions are used in this document.
!
!
CAUTIONS APPEAR BEFORE THE TEXT IT REFERENCES. CAU-
TIONS APPEAR IN CAPITAL LETTERS TO EMPHASIZE THAT THE
MESSAGE CONTAINS VITAL HEALTH AND SAFETY INFORMATION.
Warning information appears before the text it references
to emphasize that the content may prevent damage to the
device or equipment.
Indicates information that is important to know for the
proper completion of a procedure, choice of an option, or
completing a task.
Indicates additional information that is relevant to the current process or procedure.
Indicates that a component or a procedure is not applicable to this model.
Indicates a requirement that must be addressed before
proceeding with the current function or procedure.
VI
CONVENTIONS
Typographical Conventions
The following typographical conventions are used in this document:
Italics
Indicates book titles, directory names, file names, path names,
and program/process names.
Constant width
Indicates computer output shown on a computer screen, including menus, prompts, responses to input, and error messages.
Constant width bold
Indicates commands lines as entered on the computer. Variables contained within user input are shown in angle
brackets (< >).
Bold
Indicates keyboard keys that are pressed by the user.
VII
TABLE OF CONTENTS
TABLE OF CONTENTS
Conventions 0-i
Copyright 0-ix
Product Overview
Package Contents 1-1
Product Overview 1-2
Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Technical Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
Wireless Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
Hardware Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
Software Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
Product Interface 1-5
Installation
System Requirements 2-1
III
TABLE OF CONTENTS
Installing the Device 2-2
Pre-Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Installing the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Wall Mounting the Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Pole Mounting the Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Web Configuration
Logging In 3-1
Best Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Basic Network Settings
System Status 4-1
Using Save/Reload 4-1
Viewing System Information 4-2
Viewing Wireless Client List 4-4
Viewing System Log 4-5
Viewing Connection Status 4-6
Viewing DHCP Client Table 4-7
IV
TABLE OF CONTENTS
Viewing WDS Link List 4-8
System Setup 4-9
Configuring Operation Mode 4-9
Configuring IP Settings 4-10
Configuring Spanning Tree Settings 4-11
Router Setup 4-12
Configuring WAN Settings 4-12
Static IP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12
Dynamic IP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-13
Point-to-Point Protocol over Ethernet (PPPoE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-14
Point-to-Point Tunnelling Protocol (PPTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-15
Configuring LAN Settings 4-17
Configuring VPN Pass-Through 4-18
Configuring Port Forwarding 4-19
Configuring Demilitarized Zone 4-21
Configuring Wireless LAN 4-22
Configuring Wireless Settings 4-22
Access Point Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-22
Client Bridge Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-24
WDS Bridge Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-25
V
TABLE OF CONTENTS
Client Router Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27
Configuring Wireless Security 4-28
Wired Equivalent Privacy (WEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-28
Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-29
Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK). . . . . . . . . . . . . . . . . . . . . . . . . .4-30
Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Mixed . . . . . . . . . . . . . . . . . . . . . . .4-31
Wi-Fi Protected Access (WPA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-32
Wi-Fi Protected Access 2 (WPA2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-33
Wi-Fi Protected Access (WPA) Mixed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-34
Configuring Wireless MAC Filter 4-35
Configuring WDS Link Settings 4-36
Configuring Advanced Network Settings 4-37
Wireless Traffic Shaping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-37
Management Setup 4-38
Configuring Administrator Account 4-38
Configuring Management VLAN 4-39
Configuring SNMP 4-40
Configuring Backup/Restore Settings 4-42
Configuring Auto Reboot Settings 4-43
Configuring Firmware Upgrade 4-44
VI
TABLE OF CONTENTS
Configuring System Time 4-45
Configuring Wi-Fi Schedule 4-46
Add a Schedule Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-46
Schedule Services Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-47
Configuring Command Line Interface 4-48
Configuring Logging 4-49
Configuring Diagnostics 4-50
Viewing Device Discovery 4-51
Configure Denial of Service Protection 4-52
Logging Out 4-53
VII
TABLE OF CONTENTS
Appendix A
Federal Communication Commission Interference Statement A-1
Appendix B
Industry Canada Statement B-1
VIII
COPYRIGHT
Copyright
This user guide and its content is copyright of © EnGenius Networks, 2014. All rights reserved.
Any redistribution or reproduction in part or in whole in any form
is prohibited.
Do not distribute, transmit, store in any form of electronic
retrieval system or commercially exploit the content without the
expressed written permission of EnGenius Networks.
VIII
Product Overview
Chapter 1
PACKAGE CONTENTS
1.1 Package Contents
The EnStation package contains the following items:
EnStation
PoE Injector with Power Adapter
24V PoE Injector
Quick Installation Guide
Mounting Screw Set
Wall Mount Kit
Pole Mount Strap
1-1
PRODUCT OVERVIEW
1.2 Product Overview
Thank you for choosing EnStation 5. The EnStation 5 is a long
range, high performance IEEE 802.11a/n network solution that
provides Access Point, Client Bridge, WDS, and Client Router
functions in a single device.
In addition to providing the latest wireless technology, the
EnStation 5 supports Power over Ethernet and Power by
Adapter capabilities, which allow the device to be installed easily in nearly any indoor or outdoor location. Advanced features
include power level control, traffic shaping, and Real time RSSI
indication.
A variety of security features help to protect your data and privacy while you are online. Security features include Wi-Fi Protected Access (WPA PSK/WPA2 PSK), 64/128/156 bit WEP
Encryption, and IEEE 802.1x with RADIUS.
Key Features
High-speed data rates up to 300 Mbps make the EnSta-
tion 5 ideally suited for handling heavy data payloads such
as MPEG video streaming
High output power up to 26 dBm delivers superior range
and coverage
Fully Interoperable with IEEE 802.11a/IEEE 802.11n-com-
pliant devices
Point-to-point and point-to-multipoint wireless connectiv-
ity enable data transfers between two or more buildings
Channel bandwidth selection allows the appropriate band-
width to be used to reach various distances
RSSI indicator makes it easy to select the best signal for
Access Point connections
Power-over-Ethernet capabilities allow for flexible installa-
tion locations and cost savings
Four SSIDs let clients access different networks through a
single Access Point, and assign different policies and
functions for each SSID
WPA2/WPA/ WEP/ IEEE 802.1x support and MAC
address filtering ensure secure network connections
PPPoE/PPTP function support make it easy to access the
Internet via Internet Service Provider (ISP) service
authentication
SNMP Remote Configuration Management helps adminis-
trators remotely configure or manage the Access Point
QoS (WMM) support enhances performance and user
experiences
Multi-function capabilities enable users to use different
modes in various environments
1-2
BENEFITS
Benefits
The EnSt ation 5 is the ideal product around which you can build
your WLAN. The following list summarizes a few key advantages that WLANs have over wired networks:
Ideal for hard-to-wire environments
There are many scenarios where cables cannot be used to connect networking devices. Historic and older buildings, open
areas, and busy streets, for example, make wired LAN installations difficult, expensive, or impossible.
Temporary workgroups
WLANs make it easy to provide connectivity to temporary workgroups that will later be removed. Examples include parks, athletic arenas, exhibition centers, disaster-recovery shelters,
temporary offices, and construction sites.
Ability to access real-time information
With a WLAN, workers who rely on access to real-time information, such as doctors and nurses, point-of-sale employees,
mobile workers, and warehouse personnel, can access the data
they need and increase productivity , without having to look for a
place to plug into the network.
Wireless extensions to Ethernet networks
WLANs enable network managers in dynamic environments to
minimize overhead caused by moves, extensions to networks,
and other changes.
Wired LAN backup
Network managers can implement WLANs to provide backup
for mission-critical applications running on wired networks.
Mobility within training/educational
facilities
Training sites at corporations and students at universities are a
few examples where wireless connectivity can be used to facilitate access to information, information exchanges, and learning.
Frequently changed environments
WLANs are well suited for showrooms, meeting rooms, retail
stores, and manufacturing sites where workplaces are rearranged frequently.
1-3
TECHNICAL SPECIFICATION
Technical Specification
Wireless Specification
IEEE802.1 1 a/n, 2T2R, 300Mbps
Hardware Specification
Physical Interface: 2 x 10/100Mbps LAN Ports, 1 x Reset
Button
Power Supply: Passive PoE, 24V/0.6A Power Adapter
Dimension: 190(D) x 38mm(H)
Operation Temperature: -20°C ~ 60°C
Embedded high gain directional antenna
Software Specification
Operation Mode: Client Bridge, Access Point, Client
Router, WDS AP, WDS Bridge, WDS Station
Multiple SSID, Preferred SSID
PPPoE, PPTP, L2TP Pass-through
WMM, Traffic Shaping
CLI Interface, SNMP v1/v2c/v3
Recovery Page
Port Forwarding/DMZ
Narrow Bandwidth
1-4
PRODUCT INTERFACE
1.3 Product Interface
NTERFACE DESCRIPTION
I
(Access Point or Client Bridge Mode)
OFF=EnStation radio is off and the device is
not sending or receiving data over the
wireless LAN
FWAN LED
Figure 1-1: Back Panel View
ON=EnStation radio is on, and the device is
not sending or receiving data over the
wireless LAN.
Blinking=EnStation radio is on, and the
device is sending or receiving data over the
wireless LAN.
INTERFACE DESCRIPTION
ALAN Port(PoE)
B LAN Port
C Reset Button
D Power LED
E LAN(2) LEDs
1-5
The PoE interface allows EnStation to be
powered using the supplied PoE injector
To configure EnStation, connect to an
Ethernet adapter in a computer for accessing
more information
To reset factory settings, press button more
than 10 seconds.
OFF=EnStation is not receiving power
ON=EnStation is receiving power
OFF=EnStation is not connected to the
network
ON=Enstation is connected to the network
but not sending or receiving data
G Signal Indicator LED
(Client Bridge, WDS Station and Client
Router Mode)
Installation
Chapter 2
SYSTEM REQUIREMENTS
2.1 System Requirements
To install the EnStation 5, you need the following:
Computer (Windows, Linux, Mac OS X Operating System)
Web Browser (Internet Explorer, FireFox, Chrome, Safari)
Network Interface equipped: (one of the following)
Wired connectivity: Network Interface with an open
RJ-45 Ethernet Port
Wireless Connectivity:
Embedded 802.11n Wi-Fi wireless networking, IEEE
802.11a/n compatible
Wi-Fi Card, USB Wi-Fi Dongle (802.11a/n)
An existing router or access point (AP) with SSID broad-
cast
1x CAT5e Ethernet Cable
2-1
INSTALLING THE DEVICE
Note:
CAUTION!
2.2 Installing the Device
Installing the EnStation 5 on a pole or wall optimizes the wireless access range.
Only experienced installation professionals who are familiar with local building and safety codes and, wherever
applicable, are licensed by the appropriate government
regulatory authorities should install the EnStation 5.
Pre-Installation Guidelines
Select the optimal location for the equipment using the following
guidelines:
The EnStation 5 should be mounted on a 1"-4" pole. Its
location should enable easy access to the unit and its con-
nectors for installation and testing.
The higher the placement of the antenna, the better the
achievable link quality.
The antenna should be installed to provide a direct, or
near line of sight with the Base Station antenna. The
antenna should be aligned to face the general direction of
the Base Station.
Installing the Device
To install the EnSt ation 5, use the following procedure to mount
the device on a pole and refer to the figure below.
1. Remove the bottom cover protecting the RJ-45 connectors.
2. Insert an Ethernet cable into the RJ-45 port labeled LAN.
3. Install the bottom cover to protect the RJ-45 connectors.
4. Remove the power cord and PoE injector from the box
and plug the power cord into the DC port of the PoE injector.
!
ONLY USE THE POWER ADAPTER SUPPLIED WITH THE ENSTA-
TION 5. USING A DIFFERENT POWER ADAPTER MIGHT DAM-
AGE THE ENSTATION 5.
2-2
WALL MOUNTING THE DEVICE
5. Plug the other end of the Ethernet cable into the PoE port
of the PoE injector.
Figure 2-1: Installing the EnStation 5
6. Turn over the EnStation 5. Then insert the pole mounting
strap through the middle hole of the EnStation 5. Use a
screwdriver to unlock the pole-mounting ring putting it
through the EnStation 5.
Wall Mounting the Device
1. Plug the dynamic stick into the bracket firstly.
2. Combine the sealing nut and the assembled kit, as well
as tighten it.
3. Put the mock washer on dynamic stick.
4. Assemble the mounting kit with the CPE.
5. Drill the hole to input the mounting screws.
6. Use the included screws to input the mounting screws.
7. Let the hole of the bracket to aim at the screws on the
wall and hang the device to fix it.
7. Mount the EnStation 5 securely to the pole by locking the
strap tightly.
This completes the installation procedure.
2-3
Figure 2-2: Wall Mounting the Device
POLE MOUNTING THE DEVICE
Pole Mounting the Device
1. Plug the dynamic stick into the bracket firstly.
2. Combine the sealing nut and the assembled kit, as well
as tighten it.
3. Put the mock washer on dynamic stick.
4. Assemble the mounting kit with the CPE.
5. Thread the open end of the pole strap through the two
tabs on the bracket.
6. Lock and tighten pole strap to secure bracket to the pole.
Figure 2-3: Pole Mounting the Device
2-4
Web Configuration
Chapter 3
LOGGING IN
Note:
3.1 Logging In
The EnStation 5 has a built-in Web Configurator that lets you
manage the unit from any location using a Web browser that
supports HTTP and has Javascript installed.
After configuring the computer for TCP/IP using the procedure
appropriate for your operating system, use that computer’s
Web browser to log in to the EnStation 5 Web Configurator.
1. Launch your Web browser.
2. In the browser address bar, type 192.168.1.1 and
press the Enter key.
If you changed the EnStation 5 LAN IP address, enter the
correct IP address.
Figure 3-1: Web Browser Address Bar
3. When the login screen appears, enter admin for the username in the top field and admin for the password in the bottom
field.
Figure 3-2: Windows Security Login Dialog
4. Click Login to continue or Reset to abort the login.
You are now ready to use the instructions in the following chap-
ters to configure the EnStation 5.
3-1
BEST PRACTICES
Best Practices
Perform the following procedures regularly to make the EnStation 5 more secure and manage the EnStation 5 more effectively.
Change the default password Use a password that is
not easy to guess and that contains different characters,
such as numbers and letters. The EnStation 5 username
cannot be changed. For more information, see Configur-
ing Administrator Account.
Back up the configuration and be sure you know how to
restore it. Restoring an earlier working configuration can
be useful if the EnSt ation 5 becomes unstable or crashes.
If you forget your password, you will have to reset the
EnSt ation 5 to its factory default settings and lose any customized override settings you configured. However, if you
back up an earlier configuration, you will not have to completely reconfigure the EnSt ation 5. Y ou can simply restore
your last configuration. For more information, see Config-
uring Backup/Restore Settings.
3-2
Basic Network Settings
Chapter 4
Loading...