1
11N Multi-Function Access Point
EAP300
11N Multi-Function Access Point
V2.0
1
Table of Contents
1 Introduction ........................................................................................................................................................................... 4
1.1 Features and Benefits ................................................................................................................................................................. 4
1.2 Package Contents ........................................................................................................................................................................ 5
1.3 System Requirements ................................................................................................................................................................. 5
1.4 Applications ................................................................................................................................................................................. 6
2 Before you Begin .................................................................................................................................................................... 8
2.1 Considerations for Wireless Installation ..................................................................................................................................... 8
2.2 Computer Settings (Windows XP/Windows 7) ........................................................................................................................... 9
2.3 Apple Mac X OS ......................................................................................................................................................................... 12
2.4 Hardware Installation ............................................................................................................................................................... 13
3 Configuring Your Access Point ............................................................................................................................................... 14
3.1 Default Settings ......................................................................................................................................................................... 14
3.2 Web Configuration .................................................................................................................................................................... 15
4 System ................................................................................................................................................................................. 18
4.1 Operation Mode........................................................................................................................................................................ 18
4.2 Status ........................................................................................................................................................................................ 19
4.3 DHCP ......................................................................................................................................................................................... 21
4.4 Schedule .................................................................................................................................................................................... 24
4.5 Event Log ................................................................................................................................................................................... 26
4.6 Monitor ..................................................................................................................................................................................... 27
5 Wireless ............................................................................................................................................................................... 28
5.1 Status ........................................................................................................................................................................................ 28
5.2 Basic .......................................................................................................................................................................................... 29
5.3 Advanced................................................................................................................................................................................... 31
5.4 Security ..................................................................................................................................................................................... 35
5.5 Filter .......................................................................................................................................................................................... 41
2
5.6 WPS (Wi-Fi Protected Setup) .................................................................................................................................................... 43
5.7 Client List ................................................................................................................................................................................... 45
5.8 VLAN .......................................................................................................................................................................................... 46
6 Network ............................................................................................................................................................................... 47
6.1 Status ........................................................................................................................................................................................ 47
6.2 LAN ............................................................................................................................................................................................ 48
6.3 Spanning Tree ........................................................................................................................................................................... 50
7 Management ....................................................................................................................................................................... 51
7.1 Admin ........................................................................................................................................................................................ 51
7.2 SNMP ......................................................................................................................................................................................... 52
7.3 Firmware Upgrade .................................................................................................................................................................... 54
7.4 Configure ................................................................................................................................................................................... 57
7.5 Reset.......................................................................................................................................................................................... 58
8 Tools .................................................................................................................................................................................... 59
8.1 Time Setting .............................................................................................................................................................................. 59
8.2 Diagnosis ................................................................................................................................................................................... 60
8.3 LED Control ............................................................................................................................................................................... 61
9 Logout ................................................................................................................................................................................. 62
Appendix A – FCC Interference Statement .................................................................................................................................... 63
3
Version
Date
Notes
1.0 2011/0
6/24 First Release
Revision History
4
1 Introduction
EAP300
is a multi-functioned 11n product with 3 major multi-functions, is designed to operate in every working environment for
enterprises.
EAP300 is a Wireless Network device that delivers up to 6x faster speeds and 7x extended coverage than 802.11b/g devices.
EAP300 supports home network with superior throughput, performance and unparalleled wireless range.
To protect data during wireless transmissions, EAP300 encrypts all wireless transmissions through WEP data encryption and
supports WPA/WPA2. Its MAC address filter allows users to select stations with access to connect network. In addition, the
function of user isolation protects private network between client users. EAP300 thus is the best product to ensure network safety
for enterprises.
1.1 Features and Benefits
Features Benefits
High Speed Data Rate Up to 300Mbps Capable of handling heavy data payloads such as MPEG video streaming.
10/100 Fast Ethernet Support up to 100Mbps networking speed.
IEEE 802.11n draft Compliant and backward
compatible with 802.11b/g
Multi-Function, 3 functions Allowing users to select AP, WDS AP or WDS Bridge mode in various
Fully compatible with IEEE 802.11b/g/n devices.
applications.
Point-to-point, Point-to-multipoint Wireless
Connectivity
Support Multi-SSID function (4 SSID) in AP mode Allowing clients to access different networks through a single access point
Allowing to transfer data from buildings to buildings.
and to assign different policies and functions for each SSID by manager.
5
WPA2/WPA/ IEEE 802.1x support Powerful data security.
MAC address filtering in AP mode Ensuring secure network connection.
User isolation support (AP mode) Protecting the private network between client users.
Power-over-Ethernet (IEEE802.3af) Flexible Access Point locations and saving cost.
Keep personal setting Keeping the latest setting when firmware upgrade.
SNMP Remote Configuration Management Helping administrators to remotely configure or manage the Access Point
easily.
QoS (WMM) support Enhancing user performance and density.
1.2 Package Contents
The package contains the following items. In case of return, please keep the original box set, and the complete box set must be
included for full refund.
• EAP300
• 12V/1A 100V~240V Power Adapter
• RJ-45 Ethernet LAN Cable
• CD-ROM with User's Manual
• Quick Guide
1.3 System Requirements
The following are the minimum system requirements in order configure the device.
• Computer with an Ethernet interface or Wireless Network function.
• Windows, Mac OS or Linux based operating systems
6
• Internet Explorer or Firefox or Safari Web-Browser Software
1.4 Applications
The wireless LAN products are easy to install and highly efficient. The following list describes some of the many applications made
possible through the power and flexibility of wireless LANs:
a) Difficult-to-wire environments
There are many situations where wires cannot be laid easily. Historic buildings, older buildings, open areas and across
busy streets make the installation of LANs either impossible or very expensive.
b) Temporary workgroups
Consider situations in parks, athletic arenas, exhibition centers, disaster-recovery, temporary offices and construction
sites where one wants a temporary WLAN established and removed.
c) The ability to access real-time information
Doctors/nurses, point-of-sale employees, and warehouse workers can access real-time information while dealing with
patients, serving customers and processing information.
d) Frequently changed environments
Show rooms, meeting rooms, retail stores, and manufacturing sites where frequently rearrange the workplace.
e) Small Office and Home Office (SOHO) networks
SOHO users need a cost-effective, easy and quick installation of a small network.
f) Wireless extensions to Ethernet networks
Network managers in dynamic environments can minimize the overhead caused by moves, extensions to networks,
and other changes with wireless LANs.
g) Wired LAN backup
7
Network managers implement wireless LANs to provide backup for mission-critical applications running on wired
networks.
h) Training/Educational facilities
Training sites at corporations and students at universities use wireless connectivity to ease access to information,
information exchanges, and learning.
8
2 Before you Begin
This section will guide you through the installation process. Placement of the ENGENIUS EAP300 is very important to avoid poor
signal reception and performance. Avoid placing the device in enclosed spaces such as a closet, cabinet or wardrobe.
2.1 Considerations for Wireless Installation
The operating distance of all wireless devices cannot be pre-determined due to a number of unknown obstacles in the
environment that the device is deployed. These could be the number, thickness and location of walls, ceilings or other objects
that the wireless signals must pass through. Here are some key guidelines to ensure that you have the optimal wireless range.
• Keep the number of walls and ceilings between the EnGenius access point and other network devices to a minimum. Each wall or
ceiling can reduce the signal strength; the degradation depends on the building’s material.
• Building materials makes a difference. A solid metal door or aluminum stubs may have a significant negative effect on range.
Locate your wireless devices carefully so the signal can pass through a drywall or open doorways. Materials such as glass, steel,
metal, concrete, water (fish tanks), mirrors, file cabinets and brick will also degrade your wireless signal.
• Interferences can also come from your other electrical devices or appliances that generate RF noise. The most usual types are
microwaves, or cordless phones.
9
2.2 Computer Settings (Windows XP/Windows 7)
This device can be configured as an Access Point, WDS AP or WDS Bridge. The default IP address of the device is 192.168.1.1 (In
Access Point Mode as default). In order to log into this device, you must first configure the TCP/IP settings of your PC/Notebook.
• Click Start button and open Control Panel.
Windows XP Windows 7
10
• Windows XP, click [Network Connection]
• Windows 7, click [View Network Status and Tasks] then [Change adapter settings]
• Right click on [Local Area Connection] and select [Properties].
• Select “Internet Protocol (TCP/IP)” and click [Properties]
11
• Select “Use the following IP address” and enter IP address and subnet mask
then click [OK].
Note: Ensure that the IP address and subnet mask are on the same subnet as the
device.
For example: Device IP address: 192.168.1.1
PC IP address: 192.168.1.10
PC subnet mask: 255.255.255.0
12
2.3 Apple Mac X OS
• Go to System Preferences > Network
• Under Network setting, select “Manually” and enter IP
address and subnet mask.
• Click Apply when done.
13
2.4 Hardware Installation
1. Place the unit in an appropriate location after conducting a site survey.
2. Plug one end of the Ethernet cable into the Ethernet port of the device and another end into your PC/Notebook.
3. Insert the DC-inlet of the power adapter into the port labeled “DC-IN” and the other end into the power socket on the wall.
This diagram depicts the hardware configuration.
14
Operation Mode
Access Point
Wireless Security
None
3 Configuring Your Access Point
This section will show you how to configure the device using the web-based configuration interface.
3.1 Default Settings
Please use your Ethernet port or wireless network adapter to connect the Access Point.
Default Settings
IP Address 192.168.1.1
Username / Password admin / admin
Wireless SSID EnGeniusxxxxxx
Note: xxxxxx represented in the wireless SSID above is the last 6 characters of your device MAC Address. This can be found on the device body label and is
unique for each device.
15
3.2 Web Configuration
• Open a web browser (Internet Explorer/Firefox/Safari) and enter the IP Address http://192.168.1.1
Note: If you have changed the default LAN IP Address of the Access Point, ensure you enter the correct IP Address.
• The default username and password are admin. Once you have entered the correct username and password, click the Login
button to open the web-base configuration page.
• You will see the following webpage if login successfully.
16
• The navigation drop-down menu on left is divided into seven main sections:
17
1. System: This menu includes the operation mode, status, DHCP, schedule, event log, and monitor. Through this section, you
can also change the device operating mode, such as Access Point, WDS AP or WDS Bridge.
2. Wireless: This menu includes status, basic, advanced, security, filter, client list and VLAN.
3. Network: This menu includes status, LAN and spanning tree.
4. Management: This menu includes the admin setup, SNMP, firmware upgrade, save/restore backup and device reset.
5. Tools: Displays the time zone, diagnostics and LED control.
6. Logout: To logout the system. Need to open up a new browser window in order to login again.
18
4 System
4.1 Operation Mode
Each of the operating modes offers different features. In order to switch the operating mode, select it from the System >>
Operation Mode. There are three operation modes: Access Point, WDS AP and WDS Bridge.
A dialog box will appear to notify you that the system will restart in order for the change to take effect. Click on the OK button to
continue.
Please wait while the device counts down and restarts into the new operating mode.
19
System
Operation Mode
The device is cu
rrently in which mode.
System Time
The device’s system time.
System
Up T
ime The duration about the device has been operating without powering down or reboot.
Hardware Version
and
Hardware information for this device.
Kernel
and
Application
Firmware information for this device.
4.2 Status
This page will display status of the device.
If this is incorrect, please set the time in the Tools / Time page.
Serial Number
Version
20
WLAN Settings
Channel
The wireless channel in use.
ESSID
The SSID (Network Name) of the wireless network.
Security
Wireless encryption is enabled for this SSID.
BSSID
The MAC address of this SSID.
(up to 4 SSIDs are supported)
21
4.3 DHCP
This page shows the status of the DHCP server and also allows you to control how the IP addresses are allocated.
Note: Only in Access Point mode.
22
DHCP Client Table
IP address
The LAN IP address of the client.
MAC address
The MAC address of the client’s LAN interface.
Expiration Tim
e The time that the allocated IP address will expire.
Refresh
Click this button to update the DHCP Client Table.
The DHCP Client Table shows the LAN clients that have been allocated an IP address from the DHCP Server.
23
You can also manually specify the IP address that will be allocated to a LAN client by associating the IP address with its MAC
address.
Type the IP address you would like to manually assign to a specific MAC address and click Add to add the condition to the Static
DHCP Table.
24
Schedule
4.4 Schedule
This page allows you to setup the schedule times that the Wireless Active feature will be activated / deactivated.
Click Add to create a Schedule entry.
25
Schedule Description
Assign a name to the schedule.
Service
The service provides for the schedule.
Days
Define the Days to activate or deactivate the schedule.
Time of day
Define the
Time of day to activate or deactivated the schedule.
Please use 24-hour clock format.
26
Event Log
Save
Save the log
to a file.
Clear
Clear the log.
Refresh
Update the log.
4.5 Event Log
This page displays the system log of the device. When powered down or rebooted, the log will be cleared.
27
4.6 Monitor
This page shows a histogram of the Ethernet and Wireless LAN traffic. Click on [Detail] to get the detail information.
28
WLAN Settings
Channel
The wireless channel in use.
ESSID
The SSID (Network Name) of the wireless network.
Security
Wireless encryption is enabled for this SSID.
BSSID
The MAC address of this SSID.
5 Wireless
5.1 Status
This page shows the current status of the device's Wireless settings.
(up to 4 SSIDs are supported)
29
Basic
Radio
Enable or Disable the device’s wireless signal.
Mode
Select between Access Point or Wireless Distribution System (WDS)
modes.
Band
Select the types of wireless clients that the device will accept.
Enable SSID#
Select the number of SSID’s (Wireless Network names) you would like.
5.2 Basic
This page shows the current status of the device's Wireless settings.
30
SSID#
Enter the name of your wireless ne
twork. You can use up to 32 characters.
Auto Channel
When enabled, the device will scan the wireless signals around your area and select the channel with
Channel
Manually select which channel the wireless signal will use.
Check C
hannel Time
When Auto Channel is Enabled, you can specify the period of the device will scan the wireless signals
You can create up to 4 separate wireless networks.
the least interference.
around your area.
Wireless Distribution System (WDS)
Using WDS to connect Access Point wirelessly, and in doing so extend a wired
infrastructure to locations where cabling is not possible or inefficient to
implement.
Note that compatibility between different brands and models is not
guaranteed. It is recommended that the WDS network be created using the
same models for maximum compatibility.
Also note that all Access Points in the WDS network needs to use the same
Channel and Security settings.
To create a WDS network, please enter the MAC addresses of the Access
Points that you want included in the WDS. There can be a maximum of four
access points.
31
Advanced
(Access Point / WDS AP
mode)
Fragment Thre
shold
Specifies the size of the packet per fragment. This function can reduce the chance of packet collision.
RTS Threshold
When the packet size is sm
aller than the RTS Threshold, then the packet will be sent without RTS/CTS
5.3 Advanced
This page allows you to configure wireless advance settings. It is recommended the default settings are used unless the user has
experience with these functions.
However when this value is set too low, there will be increased overheads resulting in poor performance.
handshake which may result in incorrect transmission.
32
Beacon Interval
The time interval that the device broadcasts a beacon. This beacon is used to synchronize all wireless
DTIM Period
A Delivery Traffic Indication Message informs all wireless clients that the access point will be sending
N Data Rate
You can limit the transfer rates between the device and wireless clients. Each Modulation
Coding Scheme
Channel Bandwidth
Set whether each channel uses 20 or 40Mhz.
Preamble Type
A preamble is a message that helps access points synchronize with the
client.
Tx Power
Set the power output of the wireless signal.
clients on the network.
Multi-casted data.
(MCS) refers to a specific transfer speed.
To achieve 11n speeds, 40Mhz channels must be used.
Long Preamble is standard based so increases compatibility.
Short Preamble is non-standard, so it decreases compatibility but increases performance.
33
Advanced (
WDS Bridge
mode)
Fragment Threshold
Specifies the size of the packet per fragment. This function can reduce the chance of packet collision.
RTS Threshold
When the pa
cket size is smaller than the RTS Threshold, then the packet will be sent without RTS/CTS
N Data Rate
You can limit the transfer rates between the device and wireless clients. Each Modulation Coding Sc
heme
Channel Bandwidth
Set whether each channel uses 20 or 40Mhz.
Preamble Type
A preamble is a message that helps access points synchronize with the client.
However when this value is set too low, there will be increased overheads resulting in poor performance.
handshake which may result in incorrect transmission.
(MCS) refers to a specific transfer speed.
To achieve 11n speeds, 40Mhz channels must be used.
Long Preamble is standard based so increases compatibility.
Short Preamble is non-standard, so it decreases compatibility but increases performance.
34
Tx Power
Set the power output of the wireless signal.
35
Security
(Access Point / WDS AP
mode)
SSID Selection
Select the SSID that the security settings will apply to.
Separate
Tick the box
in SSID or STA
to Ena
ble
Separate feature
.
Broadcast SSID
If Disabled, then the device will not be broadcasting the SSID. Therefore it will be invisible to
wireless
WMM
Wi-
Fi Multi
-
Media is a Quality of Service protocol which prioritizes traffic in the order according to voice,
5.4 Security
This page allows you to set the wireless security settings.
Note: Only in Access Point and WDS AP mode.
Separate prevents communication and data sharing between wireless stations associated with same SSID
or different SSID.
clients.
video, best effort, and background.
36
Note that in certain situations, WMM needs to be enabled to achieve 11n transfer speed
s.
Encryption
The encryption method to be applied.
You can choose from WEP, WPA pre-shared key or WPA RADIUS.
• Disabled
• WEP - data is encrypted using the WEP standard.
• WPA-PSK - data is encrypted using the WPA-PSK standard. This is a later standard than WEP, and
provides much better security than WEP. If all your Wireless stations support WPA-PSK, you should
use WPA-PSK rather than WEP.
• WPA2-PSK - This is a further development of WPA-PSK, and offers even greater security, using the AES
(Advanced Encryption Standard) method of encryption.
• WPA-RADIUS - This version of WPA requires a Radius Server on your LAN to provide the client
authentication according to the 802.1x standard. Data transmissions are encrypted using the WPA
standard.
If this option is selected:
• This Access Point must have a "client login" on the Radius Server.
• Each user must have a "user login" on the Radius Server.
• Each user's wireless client must support 802.1x and provide the login data when required.
• All data transmission is encrypted using the WPA standard. Keys are automatically generated, so
IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing the wireless LAN. The
authentication is processed by a RADIUS server. This mode only authenticates users by IEEE 802.1x, but it does not encrypt the data during
communication.
- no data encryption is used.
no key input is required.
37
802.1x Authentication
RADIUS Server IP Address
The IP Address of the RADIUS Ser
ver
RADIUS Server port
The port number of the RADIUS Server.
RADIUS Server password
The RADIUS Server’s password.
WEP Encryption:
38
WEP Encryption
Authentication Type
Please ensure that your wireless clients use the same authentication t
ype.
Key type
ASCII
: regular text (recommended)
Key Length
Select the desired option, and ensure the wireless clients use the same setting.
Default Key
Select the key you wish to be the default. Transmitted data is ALWAYS encrypted using the Default Key;
Encryption Key #
Enter the key value or values you wish to use. Only the Key selected as Default is required. The others
HEX: for advanced users
• 64 Bit - data is encrypted, using the default key, before being transmitted. You must enter at least
• 128 Bit
the other Keys are for decryption only.
You must enter a Key Value for the Default Key.
are optional.
WPA Pre-Shared Key Encryption:
the default key. For 64 Bit Encryption, the key size is 10 chars in HEX (0~9 and A~F).
- data is encrypted, using the default key, before being transmitted. You must enter at least
the default key. For 128 Bit Encryption, the key size is 26 chars in HEX (0~9 and A~F).
39
WPA Pre
-
Shared Key Encryption
Authentication Type
Please ensure that your wireless clients use the sam
e authentication type.
WPA type
Select the WPA encryption you would like.
Pre-shared Key Type
Select whether you would like to enter the Key in HEX or Passphrase format.
Pre-shared Key
Wire
less clients must use the same key to associate the device.
WPA RADIUS Encryption:
Please ensure that your wireless clients use the same settings.
If using passphrase format, the Key must be from 8 to 63 characters in length.
40
WPA RADIUS Encryption
WPA type
Select the WPA encryption you would like.
RADIUS Server IP address
Enter the IP address of the RADIUS Server
RADIUS Server Port
Enter the port number used for connections to the RADIUS server.
RADIUS Server password
Enter the passwor
d required to connect to the RADIUS server.
Please ensure that your wireless clients use the same settings.
41
Wireless Filter (Access Point /
WDS AP
mode)
Enable Wireless Access
Tick the box to Enable Wireless Access Control.
Description
Enter a name or descripti
on for this entry.
5.5 Filter
This page allows you to create filters to control which wireless clients can connect to this device by only allowing the MAC
addresses entered into the Filtering Table.
Note: Only in Access Point and WDS AP mode.
Control
When Enabled, only wireless clients on the Filtering Table will be allowed.
42
MAC address
Enter the MAC address of the wireless client that you wish to allow connection.
Add Click this button to add the entry.
Reset
Click this button if you have made a mistake and want to reset the MAC address and Description f
ields.
MAC Address Filtering Table
Only clients listed in this table will be allowed access to the wireless network.
Delete Selected
Delete the selected entries.
Delete All
Delete all entries
Reset
Un-
tick all selected entries.
43
Wi-Fi Protected Setup (WPS)
WPS
Tick to Enable the WPS feature.
Wi-Fi Protected Setup Information
WPS Current Status
Shows whethe
r the WPS function is
Configured
or Un-
configured
.
SSID The SSID (wireless network name) used when connecting using WPS.
Authentication Mode
Shows th
e encryption method used by the WPS process.
5.6 WPS (Wi-Fi Protected Setup)
WPS feature is following the Wi-Fi Alliance WPS standard and it eases the set up of security-enabled Wi-Fi networks in the home
and small office environment.
It reduces the user steps required to configure a network and supports two methods that are familiar to most consumers to
configure a network and enable security.
Note: Only in Access Point and WDS AP mode.
Configured means that WPS has been used to authorize connection between the device and wireless
clients.
44
Passphrase Key
This is the passphrase key that is randomly generated during the WPS process. It is required if wireless
WPS Via Push
Button
Click this button to initialize WPS feature using the push button method.
WPS Via PIN
Enter the PIN code of the wireless device and click this button to initialize WPS feature using the PIN
clients that do not support WPS attempts to connect to the wireless network.
method.
45
5.7 Client List
This page shows the wireless clients that are connected to the device.
Note: Only in Access Point and WDS AP mode.
46
VLAN
Virtual LAN
Choose to Enable or Disable the VLA
N feature.
SSID#
Tag Specify the VLAN tag for each SSID.
LAN VLAN MGMT
Choose to Enable or Disable the LAN VLAN MGMT feature.
MGMT Tag
Specify the VLAN tag for LAN.
5.8 VLAN
This page allows you to configure the VLAN
Note: Only in Access Point and WDS AP mode.
47
6 Network
6.1 Status
This page shows the current status of the device’s LAN connection.
48
LAN IP
Bridge Type
Select Static IP or Dynamic IP from the drop
-
down list. If you select Static IP, you will be required to
IP address
The LAN IP Address of this device.
IP Subnet Mask
The LAN Subnet Mask of this device.
Default Gateway
The Defau
lt Gateway of this device. Leave it blank if you are unsure of this setting.
DNS Type
Select Static or Dynamic from the drop
-
down list.
First / Second DNS
The first / second DNS address for this
device
.
6.2 LAN
This page allows you to modify the device's LAN settings.
specify an IP address and subnet mask. If Dynamic IP is selected, then the IP address is received
automatically from the external DHCP server.
Address
49
DHCP Server
(Access Point mode)
DHCP Server
Enable or disable DHCP feature.
The DHCP Server automatically allocates IP addresses to your LAN
Lease Time
The duration of the DHCP server allocates each IP address to
a LAN device.
Start / End IP
The range of IP addresses of the DHCP server will allocate to LAN device.
Domain name
The domain name for this LAN network.
First / Second DNS
The first / second DNS address for this LAN network.
DHCP Server feature is only in Access Point mode.
device. Disabled as default.
Address
50
6.3 Spanning Tree
This page allows you to modify the Spanning Tree settings. Enabling Spanning Tree protocol will prevent network loops in your LAN
network.
51
Change Password
Old Password
Enter the current password.
New Password
Enter your new password.
Confirm
Passwor
d Enter your new password again for verification.
Idle Timeout
Enter Administration Page timeout time.
7 Management
7.1 Admin
This page allows you to change the system password and
to configure remote management. By default, the
password is: admin. Password can contain 0 to 12
alphanumeric characters and are case sensitive.
52
7.2 SNMP
This page allows you to assign the contact details, location, community name and trap settings for SNMP. This is a networking
management protocol used to monitor network-attached devices. SNMP allows messages (called protocol data units) to be sent
to various parts of a network. Upon receiving these messages, SNMP-compatible devices (called agents) return data stored in
their Management Information Bases.
53
SNMP
SNMP Active
Enable or disable SNMP feature.
SNMP Version
You may select a specific version or select
All from the drop
-
down list.
Read Community
Specify the password for access the SNMP community for read only access.
Set Community
Specify the password for access to the SNMP community with read/write access.
System Location
Specify the location of the device.
System Contact
Specify the contact details of the device
Trap
Trap Active
Enable or disable SNMP trapping fe
ature.
Trap Manager IP
Specify the IP address of the computer that will receive the SNMP traps.
Trap Community
Specify the password for the SNMP trap community.
54
7.3 Firmware Upgrade
This page allows you to upgrade the device's firmware.
To perform the Firmware Upgrade:
1. Click the [Browse] button and navigate to the location of the upgrade file.
2. Select the upgrade file. Its name will appear in the Upgrade File field.
3. Click the [Apply] button to commence the firmware upgrade.
Note: The device is unavailable during the upgrade process, and must restart when the upgrade is completed. Any connections to or through the device will be
lost.
55
Emergency Upgrade
If you upgrade fail, you may enter Emergency Upgrade WEB page.
1. Enter IP address: 192.168.99.9 and enter Emergency Upgrade WEB page.
Note: Refer to 2.2 to configure PC/Notebook IP address to 192.168.99.8.
2. Click the [Browse] button and navigate to the location of the upgrade file and then click [Upload].
3. Wait for 60 seconds for firmware upgrade and reboot the device.
4. You can access the device again.
56
57
Configure
Restore to Factory Default
Restores
the device to factory default settings.
Backup Settings
Save the current configuration settings to a file.
Restore Settings
Restores a previously saved configuration file.
7.4 Configure
This page allows you to save the current device configurations. When you save the configurations, you also can re-load the saved
configurations into the device through the [Restore Settings]. If extreme problems occur you can use the [Restore to Factory
Defaults] to set all configurations to its original default settings.
Click Browse to select the file. Then Upload to load the settings.
58
7.5 Reset
In some circumstances it may be required to force the device to reboot. Click on [Apply] to reboot.
59
Time
Time Setup
Select the method you want to set the time.
Time Zone
Select the time zone for your current location.
NTP Time Server
Enter the address of the Network Time Protocol (NTP) Server to automatically synchronize with
Daylight Savings
Check whether daylight savings applies to your area.
8 Tools
8.1 Time Setting
This page allows you to set the system time.
a server on the Internet.
60
Diagnosis
Address to Ping
Enter the IP address you like to see if a successful connection can be made.
Ping Frequency
Select the frequency for
Ping test.
Ping Result
The results of the Ping test.
8.2 Diagnosis
This page allows you to test your network. Type in the address for diagnosis.
61
8.3 LED Control
This page allows you to control LED on/off for Power, LAN interface and WLAN interface.
62
9 Logout
Click on [Logout] button to logout.
63
Appendix A – FCC Interference Statement
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure
installed and operated with minimum distance 20cm between the radiator & your body.
Industry Canada statement:
limits set forth for an uncontrolled environment. This equipment should be
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device
64
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son
fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
65
Appendix B – CE Interference Statement
1.1. Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been
applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
- EN60950-1
Safety of Information Technology Equipment
- EN50385
- Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to
human exposure to electromagnetic fields (0 Hz - 300 GHz)
- EN 300 328
- Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission
equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering
essential requirements under article 3.2 of the R&TTE Directive
-
EN 301 489-1
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 1: Common technical requirements
- EN 301 489-17
- Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance
RLAN equipment
66
[Czech]
požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
1999/5/EF.
tulenevatele teistele asjakohastele sätetele.
with the essential requirements and other relevant provisions of Directive 1999/5/EC.
ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
dirett
iva 1999/5/CE.
0560
Česky
Dansk
[Danish]
Deutsch
[German]
Eesti
[Estonian]
English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance
Español
[Spanish]
Ελληνική
[Greek]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets
typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp =
type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo]
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment]
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ
Français
[French]
Italiano
[Italian]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme
aux exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla
67
[Lithuanian]
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
[Hungarian]
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak
.
1999/5/EC.
koskevien direktiivin muiden ehtojen mukainen.
Latviski
[Latvian]
Lietuvių
Nederlands
[Dutch]
Malti
[Maltese]
Magyar
Polski
[Polish]
Português
[Portuguese]
Slovensko
[Slovenian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment
/ iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to
saistītajiem noteikumiem.
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van
richtlijn 1999/5/EG.
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma
mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z
zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os
requisitos essenciais e outras disposições da Directiva 1999/5/CE.
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in
ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
Suomi
[Finnish]
Svenska
[Swedish]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky
príslušné ustanovenia Smernice 1999/5/ES.
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Loading...