EnGenius EGS5110P, EGS2108P, EGS2110P User Manual

User Manual

Business Solution

8-Port Gigabit PoE+ Smart Switch

with 2 Gigabit SFP

EGS5110P

version 1.0

TABLE OF CONTENTS

I

TABLE OF CONTENTS

Conventions iv
Copyright vi

Getting Started

Overview 1-1

EGS5110P 1-1

Management Interface 1-2
Connecting the Device to the Network 1-2

Discovery in a Network with a DHCP Server 1-2
Discovery in a Network without a DHCP Server 1-3

Web Access 1-3

Management

System 2-1

Summary 2-1
IP Setting 2-2
Port Settings 2-3
PoE Management 2-4
PoE Port Configuration 2-5
Cable Diagnostics 2-6
Password 2-7
Zero Configuration 2-8

TABLE OF CONTENTS

II

L2 Feature 2-9

Port Trunking 2-9
IGMP Snooping 2-11
Multicast Group List 2-12
Port Mirroring 2-13
Loopback Detection 2-14
Static MAC Address 2-15
Dynamic Address List 2-16

VLAN 2-17

802.1Q 2-17

Adding, Editing, and Deleting Items in the list . . . . . . . . . . . . . . .2-18

PVID 2-21
Port-based VLAN 2-22

Adding, Editing, and Deleting Items in the list . . . . . . . . . . . . . . .2-23

QoS 2-25

802.1p Default Priority 2-25
CoS Priority Class 2-26
Storm Control 2-27
Bandwidth Control 2-28

Maintenance

Maintenance 3-1

Saving Configuration 3-1
Upgrading 3-2
Resetting 3-2
Rebooting 3-3
Logging Out 3-3

TABLE OF CONTENTS

III

Appendix A

Federal Communication Commission Interference
Statement A-4

Appendix B

Industry Canada Statement B-5

Appendix C

WorldWide Technical Support C-6

CONVENTIONS

IV

Conventions

The following conventions are used to give the user additional information about spe­cific procedures or content. It is important to pay attention to th ese conventions as
they provide information to prevent damage to\ equipment or personal injury.

General Conventions

The following general conventions are used in this document.

N/A:

Indicates that a component or a procedure is not applicable to this model.

Prerequisite:

Indicates a requirement that must be addressed before proceeding with the cur­rent function or procedure.

CAUTION!

CAUTIONS APPEAR BEFORE THE TEXT IT REFERENCES. CAUTIONS APPEAR IN CAPITAL LETTERS
TO EMPHASIZE THAT THE MESSAGE CONTAINS VITAL HEALTH AND SAFETY INFORMATION.

WARNING!

Warning information appears before the text it references to emphasize that the content
may prevent damage to the device or equipm e nt .

Important:

Indicates information that is important to know for the proper completion of a procedure,
choice of an option, or completing a task.

Note:

Indicates additional information that is relevant to the current process or procedure.

!

!

CONVENTIONS

V

Typographical Conventions

The following typographical conventions are used in this document:

Italics

Indicates book titles, directory names, file names, path names, and program/process
names.

Constant width

Indicates computer output shown on a computer screen, including menus, prompts,
responses to input, and error messages.

Constant width bold

Indicates commands lines as entered on the computer. Variables contained within
user input are shown in angle brackets (< >).

Bold

Indicates keyboard keys that are pressed by the user.

COPYRIGHT

VI

Copyright

This user guide and its content is copyright of © Company Name, 2013. All rights
reserved.

Any redistribution or reproduction in part or in whole in any form is prohibited.
Do not distribute, transmit, store in any form of electronic retrieval system or commer-

cially exploit the content without the expressed written permission of Company Name.

Getting Started

Chapter 1

GETTING STARTED OVERVIEW

1-1

1.1 Overview

The EGS Smart Switch Series are smart switch devices specially tailored for access
points and IP surveillance applications. The Smart Switch Series provide simple, yet,
powerful PoE manageability with features such as: Full IEEE802.3AT/AF ports, inter­nal power supply, PoE port management, loopback detection, and IGMP snooping.

The following section provides an overview of the external device views. It also pro­vides a brief description of the ports and LEDs.

1.1.1 EGS5110P

Figure 1-1 Front Panel

FRONT PANEL DESCRIPTION

A Power LED

OFF = The device is not powered on.
ON = The device is receiving power.

B PoE Maximum LED

OFF = The maximum power draw by other devices has not been
reached.

ON = The maximum power draw by connected devices has been
reached.

C System Fault LED

OFF = The device is operating.

ON = A system fault is detected.
D Factory Reset Press this to reset the device to factory default settings
E LED Mode Selector Press this to change between LAN and PoE mode.

F PoE Mode LED

OFF = The device is not in PoE mode.

ON = The device is in PoE mode.

GLAN Mode LED

OFF = The device is not in LAN mode.

ON = The device is in LAN mode.
H RJ-45 LAN Ports 10/100/1000Mbps RJ-45 LAN ports.

I SFP Ports Small form factor pluggable ports.

DEFGAB C H I

GETTING STARTED OVERVIEW

1-2

1.2 Management Interface

The company name EGS5110P features an embedded web and management inter­face for the monitoring of your device. The interface is designed to help you configure
basic and advanced features to help you improve switch efficiency and overall net­work performance.

Through the Web interface you can monitor, configure, and control your switch
remotely using a browser

1.3 Connecting the Device to the
Network

1.3.1 Discovery in a Network with a DHCP
Server

Use this procedure to setup the device within a network using the DHCP function.

1. Connect one end of an Ethernet cable (RJ-45) to the LAN port of your PC and
the other end to the device.

2. Connect the power cable to the device and turn it on.

3. On the PC connected to the device, change the PC’s IP settings with those of
the device: 192.168.0.0/24 subnet.

4. Open a Web browser on the PC and enter the following address (default): http:/
/192.168.0.239.

5. On the login screen, use the following information.
Password: password

6. Once logged in, click System -> IP Setting and select DHCP.

7. Click Apply to save the settings.

8. Connect the device to your network (DHCP enabled).

9. On the DHCP server, find and write down the IP address allocated to the
device. Use this IP address to access the management interface.

GETTING STARTED OVERVIEW

1-3

1.3.2 Discovery in a Network without a
DHCP Server

Use this procedure to setup the device within a network requiring a static IP address.

1. Connect one end of an Ethernet cable (RJ-45) to the LAN port of your PC and
the other end to the device.

2. Connect the power cable to the device and turn it on.

3. On the PC connected to the device, change the PC’s IP settings with those of
the device: 192.168.0.0/24 subnet.

4. Open a Web browser on the PC and enter the following address (default): http:/
/192.168.0.239.

5. On the login screen, use the following information.
Password: password

6. Once logged in, click System -> IP Setting and select Static IP under the Sys­tem Setting menu to configure the IP settings of the management interface.

7. Enter the IP address, subnet mask and gateway as given by your system
administrator.

8. Click Apply.

9. Connect the device to your network.

1.4 Web Access

Use this procedure to access the management interface through a Web browser for
device configuration.

1. Open a Web browser on your PC and enter the following address (default):
http://192.168.0.239.

2. On the login screen, use the following information.
Password: password

Management

Chapter 2

MANAGEMENT SYSTEM

2-1

2.1 System

The System menu enables management IP address and password to be configured
and individual port speed and Power over Ethernet (PoE) configuration and cable
diagnostics to be performed. This chapter describes these functions.

2.1.1 Summary

Click the Summary link under the System menu to see important system information
such as firmware version and chassis MAC address.

LABEL DESCRIPTION

Name This shows the model number.
FW version This shows the currently running.
Serial Number This shows the serial number.
Base MAC address This shows the chassis MAC address.
IP address This shows the IP address of the management interface.
Gateway This shows the IP address of the gateway to other subnets or networks.
System up time This shows the elapsed time since the last reboot.

MANAGEMENT IP SETTING

2-2

2.1.2 IP Setting

Click the IP Setting link under the System menu to configure the IP settings of your
device. This IP address is also the address for the management Web interface.

To access the page, click System -> IP Setting.

LABEL DESCRIPTION

Type

Use this to configure the device to use static IP settings or get its settings

via Dynamic Host Configuration Protocol (DHCP).
IP address Use this to configure the IP address of the management interface.
Subnet mask Use this to configure the subnet mask of the management interface.

Gateway

Use this to configure the IP address of a router on the same subnet as the

management interface that connects to other subnets.
Apply Click this to apply settings.

MANAGEMENT PORT SETTINGS

2-3

2.1.3 Port Settings

Click the Port Setting link under the System menu to configure the speed and duplex
settings of each port.

To access the page, click System -> Port Setting.

LABEL DESCRIPTION

Port This shows the port number.

Trunk

This show which trunk the port belongs to. For details on configuring a

trunk, refer to “Port Trunking” on page 2-9.
Link This shows whether the port is up or down at the physical layer.

Speed

Select one or more ports, select the speed and duplex settings from the

drop-down box and click apply to configure port speed and duplex set-

tings.
Apply Click this to apply settings.

MANAGEMENT POE MANAGEMENT

2-4

2.1.4 PoE Management

Ports 1~8 on the EGS51 10P are IEEE802.3at compliant ports. Each po rt is capable of
delivering up to 30W and a power budget of 124W for uninterrupted PoE use.

To access the page, click System -> PoE Management.

LABEL DESCRIPTION

Total Power Budget

Use this to configure the total power that can be supplied over all Etherne t

ports.
Current Power Used This shows how much power is being used by connected devices.
Apply Click this to apply settings.

MANAGEMENT POE PORT CONFIGURATION

2-5

2.1.5 PoE Port Configuration

You can use the PoE Port Configuration page to view PoE power information and to
configure the power settings.

To access the page, click System -> PoE Port Configuration.

LABEL DESCRIPTION

Port This shows the port number.
Priority Use this to configure which ports get power first.

Class

Use this to configure whether the power class is negotiated within a user-

defined power limit or not.

User Power Limit

Use this to configure the maximum power that is supplied over a port.

Note:

The user power limit can only be implemented when the Class value is set

to User-Defined.
State Use this to enable or disable power over Ethernet on a port.
Status
Apply Click this to apply settings.

MANAGEMENT CABLE DIAGNOSTICS

2-6

2.1.6 Cable Diagnostics

You can use the Cable Diagnostics page to perform a diagnostic on each cable con­nected to the device ports.

The cable status and length are displayed after a test is performed.
To access the page, click System -> Cable Diagnostics.

LABEL DESCRIPTION

Port Use this to select the port number.
Status This shows the state of the cable.
Cable Length This shows the cable length in meters.
Test Click this to start the test.

MANAGEMENT PASSWORD

2-7

2.1.7 Password

Use the Password page to change your current login password.
To access the page, click System -> Password.

LABEL DESCRIPTION

Password This shows the current password.
New Password Enter a new password here.
Confirm Enter the new password again here.
Apply Click this to apply settings.

MANAGEMENT ZERO CONFIGURATION

2-8

2.1.8 Zero Configuration

Use the Zero Configuration page to enable devices on your network to automatically
configure themselves and be discovered without further configuration. The Bonjour
service is enabled or disabled through the Zero Configuration page.

To access the page, click System -> Zero configuration.

LABEL DESCRIPTION

Bonjour

Use this to enable or disable auto configuration through the Bonjou r proto-

col.
Apply Click this to apply settings.

MANAGEMENT L2 FEATURE

2-9

2.2 L2 Feature

The L2 Feature menu enables port trunking, control of multicast traffic flooding, port
mirroring, cabling loop detection and MAC address table management. This chapter
describes these functions.

2.2.1 Port Trunking

Use the Port Trunking page to link multiple cables/ports in a parallel connection to
increase the throughput beyond that of a single connection. The linked cables/ports
can also act to create link redundancy.

To access the page, click L2 Feature -> Port Trunking.

Note:

You must enable trunk mode before you can add a port to a trunk group.

L

ABEL DESCRIPTION

Group This shows the trunk number.

MANAGEMENT PORT TRUNKING

2-10

Click the Apply button to accept the changes or the Cancel button to discard
them.

LABEL DESCRIPTION

Mode

Click and then click here to enable or disable a trunk. You set the

mode to Enabled before you can edit the member ports.

L

ABEL DESCRIPTION

Member Ports

Click and then click here to define which port s are members of a trunk.

MANAGEMENT IGMP SNOOPING

2-11

2.2.2 IGMP Snooping

Use the IGMP Snooping page to enable or disable this function. This feature allows
the device to listen in on the Internet Group Management Protocol (IGMP) conversa­tions between hosts and routers to map out IP multicast streams. The device can limit
flooding of traffic to IGMP designated ports.

To access the page, click L2 Feature -> IGMP Snooping.

LABEL DESCRIPTION

Setting Use this to enable or disable IGMP snooping.
Apply Click this to apply settings.

MANAGEMENT MULTICAST GROUP LIST

2-12

2.2.3 Multicast Group List

The Multicast Group List page displays a list of ports with the Multicast designation.
To access the page, click L2 Feature -> Multicast Group List.

LABEL DESCRIPTION

Group IP This shows the multicast IP address of the group.
VID This shows the VLAN ID that the multicast group is operating over.
Member Ports This shows which ports have IGMP members on them.

MANAGEMENT PORT MIRRORING

2-13

2.2.4 Port Mirroring

You can use the Port Mirroring page to view and configure source and destination
ports to define port mirroring sessions. In this way , network p ackets from one port can
be copied and sent to a monitoring connection on a different port. Both inbound or
outbound traffic (or both) can be mirrored on the device.

To access the page, click L2 Feature -> Port Mirroring.

LABEL DESCRIPTION

Direction

Use this to select whether received, transmitted or bidirectional traffic is

mirrored.
Source Port Click this to select the ports from which traffic is mirrored.
Destination Port Use this to select the port to which traffic is mirrored.
Apply Click this to apply settings.

MANAGEMENT LOOPBACK DETECTION

2-14

2.2.5 Loopback Detection

When Spanning Tree Protocol (STP) is not enabled in the network, the Loopback
Detection function can be used to detect the loop created by a specific port. Click the
Loopback Detection link under the L2 Feature menu to configure loop detection for
loops created by a specified port. For users connecting hubs or unmanaged switches,
the Loopback Detection function shuts a port when packets are sent and received
from the same port--a loopback effect. The port is automatically unlocked after the
recovery period times out.

LABEL DESCRIPTION

Time Interval

Enter how long traffic is allowed to flow over a cabling loop before the

looped ports are shut down.

Recovery Time

Enter how long after port s are shut down before they are automatically re-

enabled.
Apply Click this to apply the settings to all ports.

MANAGEMENT STATIC MAC ADDRESS

2-15

2.2.6 Static MAC Address

Click the Static MAC Address link under the L2 Feature menu to edit the MAC
address table.

LABEL DESCRIPTION

Index This shows the internal index for this MAC address table entry.

Port

Click this to select the port from which traffic to a destination MAC address

will be sent.

VID

Click this to select the VLAN ID that traffic to a destination MAC address

will be sent.

MAC Address

Click this select the destination MAC address that will be matched to traf-

fic.
Add Click this to add a new entry to the MAC address table.
Edit Click this to edit an existing entry listed in the MAC address table.
Delete Click this to delete an existing entry listed in the MAC address table.

MANAGEMENT DYNAMIC ADDRESS LIST

2-16

2.2.7 Dynamic Address List

Click the Dynamic Address List link under the L2 Feature menu to show the MAC
address table.

LABEL DESCRIPTION

Index This shows the internal index for this MAC address table entry.

Port

This shows the port from which traffic to a destination MAC address is

sent.
VID This shows the VLAN ID that traffic to a destination MAC address is sent.
MAC Address This shows the destination MAC address that is matche d to traffic.

MANAGEMENT VLAN

2-17

2.3 VLAN

The VLAN menu enables configuration of 802.1Q VLANs or port-based VLANs. This
chapter describes these functions.

2.3.1 802.1Q

Click the 802.1Q link under the VLAN menu to configure which egress ports add

802.1Q tags to traffic.

Important:

Port-based VLAN and 802.1Q VLAN are mutually exclusive. If you enable port-based
VLAN, then 802.1Q VLAN is disabled.

Note:

All ports with a VID of 1 are assigned to the default VLAN.

L

ABEL DESCRIPTION

VID This shows the 802.1Q tag that is added to egress traffic on these ports.
Name Defines the name of the VLAN.

Tagged Ports

Shows the egress ports that tag traffic. Selecting tagged ports removes

them from the Untagged Ports fiel d.

Untagged Ports

Shows the egress ports that don’t tag traffic. Selecting untagged ports

removes them from the Tagged Ports field.

MANAGEMENT ADDING, EDITING, AND DELETING ITEMS IN THE LIST

2-18

Adding, Editing, and Deleting Items in the
list

To add an item to the 802.1Q list, follow these steps:

1. Click the Add button .

2. Enter the VID and name values in the VID and Name text boxes.

3. Click the Tagged Ports text box to show the tagged ports dialog box.

4. Click a radio button in the tagged ports row to select a port.

5. Click the Untagged Ports text box to show the untagged ports dialog box.

6. Click a radio button in the untagged ports row to select a port.

LABEL DESCRIPTION

Enabled Click this to enable 802.1Q VLANs. This feature is enabled by default.

MANAGEMENT ADDING, EDITING, AND DELETING ITEMS IN THE LIST

2-19

7. Click Confirm to accept the changes or Cancel discard them.

To edit an item in the 802.1Q list, follow these steps:

1. Click the edit button .

2. Enter the VID and name values in the VID and Name text boxes.

3. Click the Tagged Ports text box to show the tagged ports dialog box.

4. Click a radio button in the tagged ports row to select a port.

5. Click the Untagged Ports text box to show the untagged ports dialog box.

6. Click a radio button in the untagged ports row to select a port.

7. Click Confirm to accept the changes or Cancel discard them.

MANAGEMENT ADDING, EDITING, AND DELETING ITEMS IN THE LIST

2-20

To delete an item in the 802.1Q list, follow these steps:

1. Click the delete button in the row you want to remove. A confirmation dialog
is displayed.

2. Click OK to continue or Cancel to abort the changes.

MANAGEMENT PVID

2-21

2.3.2 PVID

Click the PVID link under the VLAN menu to tag outgoing, untagged packets and to
filter incoming packets.

Note:

To enable PVID functionality the following requiremnents must be met:

 All ports must have a defined PVID.
 If no other value is specified, the default VLAN PVID is used.
 If you want to change the port’s default PVID, you must first create a VLAN that

includes the port as a member.

L

ABEL DESCRIPTION

Port This shows the port number.
Trunk This shows the trunk number (if any are defined for this port).
PVID Select one or more ports and then click here to select a PVID.
Apply Click this to apply settings.

MANAGEMENT PORT-BASED VLAN

2-22

2.3.3 Port-based VLAN

Click the Port-based VLAN link under the VLAN menu to enable and show port-based
VLANs.

Important:

Port-based VLAN and 802.1Q VLAN are mutually exclusive. If you enable port-based
VLAN, then 802.1Q VLAN is disabled.

L

ABEL DESCRIPTION

VID This shows the VLAN ID of the port-based VLAN.
Name This shows the name of the port-bas ed VLAN.
Member Ports This shows which ports belong to this port-based VLAN.

L

ABEL DESCRIPTION

Enabled

Click this to enable port-based VLANs. This feature must be enabled to
configure a port-based VLAN.

MANAGEMENT ADDING, EDITING, AND DELETING ITEMS IN THE LIST

2-23

Adding, Editing, and Deleting Items in the
list

To add an item to the 802.1Q list, follow these steps:

1. Click the Add button .

2. Enter the VID and name values in the VID and Name text boxes.

3. Click the Member Ports text box to show the ports dialog box.

4. Click a check box in the member ports row to select a port.

5. Click Confirm to accept the changes or Cancel discard them.

MANAGEMENT ADDING, EDITING, AND DELETING ITEMS IN THE LIST

2-24

To edit an item in the 802.1Q list, follow these steps:

1. Click the edit button .

2. Enter the VID and name values in the VID and Name text boxes.

3. Click the Member Ports text box to show the member ports dialog box.

4. Click a check box in the member ports row to select a port.

5. Click Confirm to accept the changes or Cancel discard them.

To delete an item in the 802.1Q list, follow these steps:

1. Click the delete button in the row you want to remove. A confirmation dialog
is displayed.

2. Click OK to continue or Cancel to abort the changes.

MANAGEMENT QOS

2-25

2.4 QoS

The QoS menu enables traffic to be prioritized, excessive broadcast and multicast
traffic to be avoided and overall bandwidth to be limited on a port-by-port basis. This
chapter describes these functions.

2.4.1 802.1p Default Priority

Click the 802.1p Default Priority link under the QoS menu to define which 802.1p/Q
priority is applied to untagged ingress traffic. The priority level is from 0 to 7.
EGS5110P supports four class quality levels: low, normal, medium, and high. To find
out how to map the priority value to one of the four classes, refer to “CoS Priority
Class” on page 2-26.

LABEL DESCRIPTION

Port This shows the port number.

Trunk

This shows the trunk number (if any are defined for this port). Ports

assigned to the same trunk group are assigned the same priority level.
Priority Select the priority for untagged traffic arriving on this port.
Apply Click this to apply settings.

MANAGEMENT COS PRIORITY CLASS

2-26

2.4.2 CoS Priority Class

Click the CoS Priority Class link under the QoS menu to define which 802.1p/Q prior­ity class (low, normal, medium, or high) is applied to untagged ingress traffic.

LABEL DESCRIPTION

Priority This shows the Priority Code Point (PCP) that matches ingress traffic.

Class

Select the Class of Service (CoS) that is applied to traffic. Traf fic classified

as High CoS are sent first.
Apply Click this to apply settings.

MANAGEMENT STORM CONTROL

2-27

2.4.3 Storm Control

The Storm Control feature provides the ability to control the receive rate of broadcast,
multicast, and unknown unicast packets. Click the Storm Control link under the QoS
menu to limit excessive flooding caused by a packet storm.

LABEL DESCRIPTION

Port

Type Use this to select which type of traffic will be limited.

 Unknown Unicast: If the rate of unknown L2 unicast (destination

lookup failure) traffic ingressing on an interface increases beyond the
configured threshold, the traffic will be dropped.

 Multicast: If the rate of L2 multicast traffic ingressing on an interface

increases beyond the configured threshold, the traffic will be dropped.

 Broadcast: If the rate of L2 broadcast traffic ingressing on an interface

increases beyond the configured threshold, the traffic will be dropped.

Threshold Use this to configure how many packets per second are allowed to flood.

MANAGEMENT BANDWIDTH CONTROL

2-28

2.4.4 Bandwidth Control

Click the Bandwidth Control link under the QoS menu to define how much traffic can
pass through a port.

LABEL DESCRIPTION

Port This shows the port number.
Trunk This shows the trunk number (if any are defined for this port).
Tx Use this to configure the maximum bandwidth this port sends out.
Rx Use this to configure the maximum bandwidth this port accepts.
Apply Click this to apply settings.

Maintenance

Chapter 3

MAINTENANCE MAINTENANCE

3-1

3.1 Maintenance

Maintenance functions are available from the maintenance bar. Maintenance func­tions include: Saving Configuration settings, Upgrading firmware, Resetting the con­figuration to factory defaults, Rebooting the device, and Logging Out of the interface.

The following is the Maintenance menu bar.

Figure 3-1 Maintenance Bar

3.1.1 Saving Configuration

Follow this procedure to save the configuration, so it will survive a reboot.

1. Click to begin saving the configuration settings.

2. Click OK.

Important:

You must save any setting changes before rebooting. Failing to save results in loss of
new configuration changes.

MAINTENANCE MAINTENANCE

3-2

3.1.2 Upgrading

Follow this procedure to upgrade the firmware.

1. Click to start upgrading.

2. Click Choose File. A window opens, browse to the location of your new firm­ware.

3. Select the new firmware file and click OK.

4. A prompt displays to confirm the firmware upgrade. Click OK and follow the on­screen instructions to complete the firmware upgrade.

3.1.3 Resetting

Follow this procedure to reset the device to factory default settings.

1. Click to start the rest process.

2. A prompt displays, click OK to confirm the reset or Cancel to quit the procedure.

WARNING!

Backup your configuration information before upgrading to prevent loss of setting infor­mation.

Note:

The Upgrade process may require a few minutes to complete.

WARNING!

The Reset function will delete all configuration information from the current device.
Backup your information before starting this procedure.

!

!

MAINTENANCE MAINTENANCE

3-3

3.1.4 Rebooting

Follow this procedure to reboot the device.

1. Click to start the reboot process.

2. A prompt displays, click OK to confirm the reboot or Cancel to quite the proce­dure.

3.1.5 Logging Out

Follow this procedure to log out the current profile from the user interface.

1. Click to log out of the menu.

2. A prompt displays, click OK to confirm the logout or Cancel to quit the proce­dure.

APPENDIX FEDERAL COMMUNICATION COMMISSION INTERFER-

A-4

Appendix A

Federal Communication Commis­sion Interference Statement

This equipment has been tested and found to comply with the limits for a Class B dig­ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro­vide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interfer­ence to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interfer­ence to radio or television reception, which can be determined by turning the equip­ment off and on, the user is encouraged to try to correct the interference by one of the
following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol­lowing two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

FCC Radiation Exposure Statement

WARNING!

Any changes or modifications not expressly approved by the party responsible for com­pliance could void the user's authority to operate this equipment.

Important:

This equipment complies with FCC radiation exposure limit s set fort h for an uncontr olled
environment.
This device complies with FCC RF Exposure limits set forth for an uncontrolled environ­ment, under 47 CFR 2.1093 paragraph (d)(2).
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

!

APPENDIX INDUSTRY CANADA STATEMENT

B-5

Appendix B

Industry Canada Statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is sub­ject to the following two conditions: (1) This device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux condi­tions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2)
ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.

Important:

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établie s
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.

APPENDIX WORLDWIDE TECHNICAL SUPPORT

C-6

Appendix C

WorldWide Technical Support

REGION/COUNTRY

OF PURCHASE

SERVICE

C

ENTRE

SERVICE INFORMATION

Canada

CANADA web site www.engeniuscanada.com

email [e-mail]
contact num-

bers

Toll Free: ([phone]
Local: ([phone]

hours of opera­tion

Monday - Friday
9:00AM to 5:30PM EST (GMT-5)

USA

LOS ANGE­LES, USA

web site www.engeniu stech.com

email [e-mail]
contact num-

bers

Toll Free: ([phone]
Local: ([phone]

hours of opera­tion

Monday - Friday
8:00 AM to 4:30 PM PST (GMT-8)

Mexico, Central
and Southern
America

MIAMI, USA web site

[ES] es.engeniustech.com
[PT] pg.engeniustech.com

email [e-mail]

contact num­bers

Miami: ([phone]
Sao Paulo, Brazil: ([phone]
D.F., Mexico:([phone]

hours of opera­tion

Monday - Friday
8:00 AM to 5:30PM EST (GMT-5)

Europe

NETHER­LANDS

web site www.engeniusnetworks.eu

email [e-mail]
contact num-

bers

([phone]

hours of opera­tion

Monday - Friday
9:00 AM - 5:00 PM (GMT+1)

APPENDIX WORLDWIDE TECHNICAL SUPPORT

C-7

Africa, Middle
East, Russia, CIS/
Armenia, Azerbai­jan, Belarus,
Georgia, Kazakh­stan, Kyrgyzstan,
Moldova, Tajiki­stan, Turkmeni­stan, Ukraine,
Uzbekistan, Tur­key, Afghanistan,
Pakistan, Bangla­desh, Maldives,
Nepal, Bhutan, Sri
Lanka

DUBAI, UAE web site www.engenius-me.com

email [e-mail]

contact num­bers

Toll Free:
U.A.E.: 800-EnGenius
800-364-364-87
General:
([phone]

hours of opera­tion

Sunday - Thursday
9:00 AM - 6:00 PM (GMT+4)

Singapore, Cam­bodia, Indonesia,
Malaysia, Thai­land, Philippines,
Vietnam, China,
Hong Kong,
Korea, India,
South Africa, Oce­ania

SINGA­PORE

web site

www.engenius tech.com.sg/
e_warranty_form

email [e-mail]
contact num-

bers

Toll Free:
Singapore: 1800-364-3648

hours of opera­tion

Monday - Friday
9:00 AM - 6:00 PM (GMT+8)

Others

TAIWAN,
R.O.C.

web site www.engeniusnetworks.com

email [e-mail]

Note:

* Service hours are based on the local time of the service center.
* Please visit the website for the latest information about customer service.

R

EGION/COUNTRY

OF PURCHASE

SERVICE

C

ENTRE

SERVICE INFORMATION