Eneo NXP-880F26 Quick Installation Manual
Quick Installation Guide
1/2.8” Network Board Camera,
EN
1920x1080, Day&Night, 2.6mm,
D-WDR, PoE, 12V
NXP-880F26
Table of content
Components ...................................................................................................................5
Installation .....................................................................................................................6
Extension Cable .................................................................................................................................................................6
Connection ..........................................................................................................................................................................6
Micro SD memory slot ................................................................................................................................................ 6
RJ-45 port ....................................................................................................................................................................... 7
Connecting the Power ................................................................................................................................................7
Network Connection & IP assignment .......................................................................................................................7
Operation .......................................................................................................................9
Access from a browser .....................................................................................................................................................9
Access from the internet .............................................................................................................................................. 10
Setting the admin password over a secure connection ................................................................................... 10
Live View Page ................................................................................................................................................................. 10
General controls ........................................................................................................................................................ 11
Control toolbar .......................................................................................................................................................... 11
Video Streams ............................................................................................................................................................. 12
Playback ....................................................................................................................................................................... 12
Network Camera Setup ............................................................................................................................................... 15
Resetting to the factory default settings ............................................................................................................... 16
Further information ...................................................................................................................................................... 16
2
Safety instructions
General safety instructions
• Before switching on and operating the system, rst read this safety advice and the operating instructions.
• Keep the operating instructions in a safe place for later use.
• Installation, commissioning and maintenance of the system may only be carried out by authorised
individuals and in accordance with the installation instructions - ensuring that all applicable standards and
guidelines are followed.
• Protect the devices from water penetration and humidity, since these can cause lasting damage.
• Should moisture nevertheless enter the system, under no circumstance switch on the devices under these
conditions, instead send them for examination to an authorised specialist workshop.
• The system must never be used outside of the technical specications, since this can destroy it.
• The device must be protected from excesses of heat, dust, humidity and vibration.
• When separating the system from the voltage supply, only ever use the plug to pull out the cable. Never
pull directly on the cable itself.
• Lay the connecting cables carefully and check that they are not mechanically stressed, kinked or damaged
and that no humidity can penetrate into them.
• In the event of a malfunction, please inform your supplier.
• Maintenance and repairs may only be carried out by authorised specialist personnel.
• The system must be isolated from the power supply before opening the housing.
• The device may only be opened by qualied service personnel. Unauthorised access invalidates any
warranty claim.
• Connection cables should always be exchanged through Videor E. Hartig GmbH.
• Use only original spare parts and accessories from Videor E. Hartig GmbH.
• The housing should only be cleaned using a mild domestic cleaning agent. Never use solvents or petrol as
these can permanently damage the surface.
• During installation, it is essential to ensure that the seals provided are correctly installed and that they are
not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.
• The installer is responsible for the maintenance of the enclosure as per the technical data, e.g. by sealing
the cable outlets with silicone.
• Wire end ferrules should be used when shortening the exible connection cables.
• The devices may only be operated in the temperature range indicated in the data sheet and within the
dened air humidity range.
EN
Product - Specic Safety Instructions
• The camera may never be pointed directly at the Sun with the aperture open (this will destroy the sensor).
• It is unavoidable that during manufacture and to a certain extent during later use, humidity will be present
in the ambient air within the device’s housing. In the event of large temperature uctuations, this humidity
may condense inside the housing.
• To avoid this condensation inside the very tightly sealed housing, the manufacturer has inserted silica gel
sachets in the housing of the various camera types.
• It is however a physical given, that these silica gel bags will reach saturation after a certain amount of time.
They should therefore be replaced with new silica gel sachets.
• During installation, it is essential to ensure that the seals provided are correctly installed and that they are
not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.
• A multipolar, easily accessible isolation device should be installed in the proximity of the IR Spotlight, in
order to disconnect the device from the power supply for service work.
• The earth connection must be made according to the low impedance requirement of DIN VDE 0100.
• Subsequent painting of the equipment surface can impair the function.
• Any warranty claim is invalidated by subsequent painting.
• A safety margin of > 1m from the spotlight must be maintained when viewing directly into the IR Spotlight
in a darkened environment.
• Do not look directly at invisible LED radiation using optical instruments (e.g. a reading glass, magnifying
glass or microscope), since this can endanger the eyes, LED Class 1M.
• Operation of the IR spotlight with a defective cover or during repair is prohibited.
3
Class A device note
This is a Class A device. This device can cause malfunctions in the living area; in such an event, the operator may
need to take appropriate measures to compensate for these.
WEEE (Waste Electronical & Electronic Equipment)
Correct Disposal of This Product (Applicable in the European Union and other European countries with separate
collection systems).
This marking shown on the product or its literature, indicates that it should not be disposed with
other household wastes at the end of its working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable reuse of material resources. Household users
should contact either the retailer where they purchased this product, or their local government
oce, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
Graphical symbols
Please pay attention to the safety instructions, and carefully read through this instruction guide before initial
operation.
Important points of warning are marked with a caution symbol.
Important points of advice are marked with a notice symbol.
i
4
Components
This system comes with the following components;
• Module Camera
• Installation Guide
i
Notice: Check your package to make sure that you received the complete system,
including all components listed above.
i
Notice: Adapter for DC 12V is not supplied.
EN
5
Installation
For the operation of the Network Camera, it is necessary to connect a network cable
for data transmission, power connection from supplied power adapter. Depending on
operation methods, it is possible to connect an alarm cable additionally. For its xation on
dierent locations, please consult with an installer.
Extension Cable
NO Item Description
1 RJ-45 Ethernet, RJ-45 port compatible with 10/100Mbps PoE Modular Jack
2 DC Jack Main Power, DC Jack, DC12V
AI: Alarm In
3
AO: Alarm Out
4
5
MIC: Audio In
G: GND
SPK: Audio Out
G: GND
Alarm input and output, 3pin terminalG: GND
Audio line input, 2pin terminal
Audio line output, 2pin terminal
Connection
Micro SD memory slot
Remove the bubble of the camera to insert the SD memory card.
6
Loading...