Eneo NXC Series, NXC-1401M, NXC-1402M, NXC-1301M, NXC-1302M Installation Operation User Manual

1

INSTALLATION / OPERATION / USER’S MANUAL

NXC Series

MEGAPIXEL NETWORK CAMERA

2

3

WARNINGS AND CAUTIONS:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.

CAUTION

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.

PRECAUTIONS

Safety ---------------------------------- Installation -----------------------------

Cleaning ----------------------------------

CAUTION

RISK OF ELECTRNIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by the qualified
personnel before operating it any further.

Unplug the unit from the wall oulet if it is not going to
be used for several days or more. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.

Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials(curtains, draperies)
that may block the ventilation holes.

Height and vertical linearity controls located at the rear
panel are for special adjustments by qualified
personnel only.

Do not install the unit in an extremely hot or humid place
or in a place subject to excessive dust, mechanical
vibration.

The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.

Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong
solvents such as thinner or benzene as they might
damage the finish of the unit.

Retain the original carton and packing materials for safe
transport of this unit in the future.

4

FCC COMPLIANCE STATEMENT

CE COMPLIANCE STATEMENT

FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO

COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF
THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE
PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS
OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES,
AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AN D USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A
RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE
THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN
EXPENSE.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE

PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO
OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME NMB-003 DU
CANADA.

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

5

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS -- All the safety and operating instructions should be read before the
appliance is operated.

2. RETAIN INSTRUCTIONS -- The safety and operating instructions should be retained for future
reference.

3. CLEANING -- Unplug video monitor or equipment from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4. ATTACHMENTS -- Do not use attachments not recommended by the video monitor or
equipment manufacturer as they may result in the risk of fire, electric shock or injury to persons.

5. WATER AND MOISTURE -- Do not use video monitor or equipment near water - for example,
near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool or the like.

6. ACCESSORIES -- Do not place video monitor or equipment on an unstable cart, stand or table.
The video monitor or equipment may fall causing serious injury to a child or adult and serious
damage to the equipment. Wall or shelf mounting should follow the manufacturer's instructions
and should use a mounting kit approved by the manufacturer.

6A. Video monitor or equipment and cart combinations should be moved with care.

Quick stops, excessive force and uneven surfaces may cause the equipment and cart
combination to overturn.

7. VENTILATION -- Slots and openings in the cabinet at the back or bottom are provided for
ventilation and to ensure reliable operation of the video monitor or equipment and to protect it
from overheating. These openings must not be blocked or covered. The openings should never
be blocked by placing the video monitor or equipment on a bed, sofa, rug, or other similar
surface. Video monitor or equipment should never be placed near or over a radiator or heat
register. Video monitor or equipment should not be placed in a built-in installation such as a
bookcase unless proper ventilation is provided.

8. POWER SOURCES -- Video monitor or equipment should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type of power supplied to
your home, consult your video monitor or equipment dealer or local power company. For video
monitor or equipment designed to operate from battery power refer to the operating instructions.

9. GROUNDING OR POLARIZATION -- This video monitor may be equipped with a polarized
alternating - current line plug (a plug having one blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Alternate
Warnings - This video monitor is equipped with a three-wire grounding-type plug, a plug having
a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety

6

feature. If you are unable to insert the plug into the outlet, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

10. POWER CORDS -- Do not allow anything to rest on the power cord. Do not locate video monitor
or equipment where the cord will be abused by persons walking on it.

11. HEED WARNINGS -- Follow all instructions marked on the video monitor or equipment.

12. LIGHTNING -- For added protection for video monitor or equipment during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the video product due to
lightning and power-line surges.

13. OVERLOADING --Do not overload wall outlets and extension cords as this can result in a risk of
fire or electric shock.

14. OBJECT AND LIQUID ENTRY -- Never push objects of any kind into video monitor or
equipment through openings as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind on the product.

15. SERVICING -- Do not attempt to service video monitor or equipment yourself as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.

16. DAMAGE REQUIRING SERVICE -- Unplug video monitor or equipment from the wall outlet and
refer servicing to qualified service personnel under the following conditions:
A. When the power-supply cord or the plug has been damaged.
B. If liquid has spilled or objects have fallen into the video product.
C. If the video product has been exposed to rain or water.
D. If the video product does not operate normally by following the operating instructions, adjust

only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by a qualified

technician to restore the video product to its normal operation.
E. If the video product has been dropped, or the cabinet damaged.
F. When the video product exhibits a distinct change in performance -- this indicates a need for

service.

17. REPLACEMENT PARTS -- When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or that have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or
other hazards.

18. SAFETY CHECK -- Upon completion of any service or repairs to this video product, ask the
service technician to perform safety checks to determine that the video product is in proper
operating condition.

19. FIELD INSTALLATION -- This installation should be made by a qualified service person and
should conform to all local codes.

7

CONTENTS

DESCRIPTION ----------------------------------------------------------------------------------------------------11
Models ---------------------------------------------------------------------------------------------------11
Key Features --------------------------------------------------------------------------------------------11
Components --------------------------------------------------------------------------------------------12

Camera Layout -----------------------------------------------------------------------------------------13

INSTALLATION ---------------------------------------------------------------------------------------------------15

Before Installation -------------------------------------------------------------------------------------15
Starting Installation ------------------------------------------------------------------------------------15
DC Auto Iris Lens Installation & Adjustment -------------------------------------------------------16
Audio Connection --------------------------------------------------------------------------------------17
Alarm Connection --------------------------------------------------------------------------------------17

OPERATION -------------------------------------------------------------------------------------------------------18

Minimum conditions for using web browser -------------------------------------------------------18
Accessing the IP camera ------------------------------------------------------------------------------18
Main Menu ----------------------------------------------------------------------------------------------19

LIVE VIEW --------------------------------------------------------------------------------------------------------20

Live Video Page Icons ---------------------------------------------------------------------------------21

SETUP -------------------------------------------------------------------------------------------------------------22

Users -----------------------------------------------------------------------------------------------------23
Network -------------------------------------------------------------------------------------------------26
Image ----------------------------------------------------------------------------------------------------27
Audio -----------------------------------------------------------------------------------------------------29
Date & Time --------------------------------------------------------------------------------------------31
Live View – Source ------------------------------------------------------------------------------------32
Image – Basic ------------------------------------------------------------------------------------------35
Image – AE & AWB ------------------------------------------------------------------------------------36
Image – Day & Night ----------------------------------------------------------------------------------39
Video & Image – Stream1 ----------------------------------------------------------------------------41
Video & Image – Stream2 ----------------------------------------------------------------------------43
Video & Image – Stream3 ----------------------------------------------------------------------------46
Video & Image – Stream4 ----------------------------------------------------------------------------49
Video & Image – Webcasting ------------------------------------------------------------------------53
Audio – Basic -------------------------------------------------------------------------------------------54
Event In – Alarm-In ------------------------------------------------------------------------------------56
Event In – Manual Trigger ----------------------------------------------------------------------------58
Event In – VMD Stream1 ----------------------------------------------------------------------------59
Event In – VMD Stream3 -----------------------------------------------------------------------------61

8

Event In – VMD Stream4 -----------------------------------------------------------------------------63
Event Out – SMTP --------------------------------------------------------------------------------------65
Event Out – FTP& JPEG -------------------------------------------------------------------------------68
Event Out – Audio Alert -------------------------------------------------------------------------------69
Event Out – Audio Alert – Audio Recorder -------------------------------------------------------70
Event Out – PTZ Preset--------------------------------------------------------------------------------72
Event Out – SD Record --------------------------------------------------------------------------------73
Event Map -----------------------------------------------------------------------------------------------75
Event Map – Add ---------------------------------------------------------------------------------------76
Device – PTZ --------------------------------------------------------------------------------------------77
Device – RS485 -----------------------------------------------------------------------------------------78
SD Playback – SD Playback List View ---------------------------------------------------------------79
Security – Users ----------------------------------------------------------------------------------------81
Security – HTTPS --------------------------------------------------------------------------------------84
Security – IP Filtering ----------------------------------------------------------------------------------86
Date & Time ------------------------------------------------------------------------------------------- 87
Network – Basic ----------------------------------------------------------------------------------------89
Network – DDNS ---------------------------------------------------------------------------------------91
Network – RTP -----------------------------------------------------------------------------------------92
Network – UPnP ----------------------------------------------------------------------------------------94
Network – QoS ----------------------------------------------------------------------------------------95
Language -----------------------------------------------------------------------------------------------96
Maintenance --------------------------------------------------------------------------------------------97
Support --------------------------------------------------------------------------------------------------99
About ---------------------------------------------------------------------------------------------------100

Technical Specifications ---------------------------------------------------------------------------------------101

Models --------------------------------------------------------------------------------------------------101
General -------------------------------------------------------------------------------------------------101
Electrical / Connector --------------------------------------------------------------------------------101
Mechanical ---------------------------------------------------------------------------------------------102
Video ---------------------------------------------------------------------------------------------------102
Audio ---------------------------------------------------------------------------------------------------103
System Integration -----------------------------------------------------------------------------------103
Environmental -----------------------------------------------------------------------------------------103
Physical ------------------------------------------------------------------------------------------------104

Troubleshooting -------------------------------------------------------------------------------------------------105

Upgrading the Firmware -----------------------------------------------------------------------------105
General Troubleshooting ----------------------------------------------------------------------------105

9

LIST of ILLUSTRATIONS

Figure 1. 4-pin iris driver connector ---------------------------------------------------------------------------16
Figure 2. DC auto iris Lens connection -----------------------------------------------------------------------16
Figure 3. Audio connection -------------------------------------------------------------------------------------17
Figure 4. Alarm connector --------------------------------------------------------------------------------------17
Figure 5. Main menu ---------------------------------------------------------------------------------------------19
Figure 6. Main Live View Page ---------------------------------------------------------------------------------20
Figure 7. Basic Configuration -----------------------------------------------------------------------------------22
Figure 8. Basic Configuration / Users -------------------------------------------------------------------------23
Figure 9. Basic Configuration / Users / Add User -----------------------------------------------------------24
Figure 10. Basic Configuration / Users / Modify User -------------------------------------------------------25
Figure 11. Basic Configuration / Network --------------------------------------------------------------------26
Figure 12. Basic Configuration / Image -----------------------------------------------------------------------27
Figure 13. Basic Configuration / Audio ------------------------------------------------------------------------29
Figure 14. Basic Configuration / Date & Time ---------------------------------------------------------------31
Figure 15. Live View / Source ----------------------------------------------------------------------------------32
Figure 16. Video & Image / Image – Basic ------------------------------------------------------------------35
Figure 17. Video & Image / Image – AE & AWB ------------------------------------------------------------36
Figure 18. Video & Image / Day & Night ---------------------------------------------------------------------39
Figure 19. Video & Image / Stream1 -------------------------------------------------------------------------41
Figure 20. Video & Image / Stream2 -------------------------------------------------------------------------43
Figure 21. Video & Image / Stream2 ROI setting -----------------------------------------------------------45
Figure 22. Video & Image / Stream3 -------------------------------------------------------------------------46
Figure 23. Video & Image / Stream3 ROI setting -----------------------------------------------------------48
Figure 24. Video & Image / Stream4 -------------------------------------------------------------------------49
Figure 25. Video & Image / Stream4 ROI setting -----------------------------------------------------------52
Figure 26 Video & Image / Webcasting ----------------------------------------------------------------------53
Figure 27. Audio / Basic ----------------------------------------------------------------------------------------54
Figure 28. Event / Event In – Alarm In -----------------------------------------------------------------------56
Figure 29. Event / Event In – Manual Trigger ---------------------------------------------------------------58
Figure 30. Event / Event In – VMD Stream1 -----------------------------------------------------------------59
Figure 31. Event / Event In – VMD Stream3 -----------------------------------------------------------------61
Figure 32. Event / Event In – VMD Stream4 -----------------------------------------------------------------63
Figure 33. Event / Event Out – SMTP (Email) ---------------------------------------------------------------65
Figure 34. Event / Event Out – FTP & JPEG -----------------------------------------------------------------67
Figure 35. Event / Event Out – Audio Alert ------------------------------------------------------------------69
Figure 36. Event / Event Out – Audio Alert / Audio Recorder----------------------------------------------70
Figure 37. Event / Event Out – Audio Alert / ARecorder window -----------------------------------------70
Figure 38. Event / Event Out – Audio Alert / Encode setup -----------------------------------------------71
Figure 39. Event / Event Out – PTZ Preset ------------------------------------------------------------------72
Figure 40. Event / Event Out – SD Record -------------------------------------------------------------------73
Figure 41. Event / Event Map ----------------------------------------------------------------------------------74
Figure 42. Event / Event Map – Add --------------------------------------------------------------------------75

10

Figure 43. Device / PTZ------------------------------------------------------------------------------------------77
Figure 44. Device / RS485---------------------------------------------------------------------------------------78
Figure 45. SD Playback / Playback List View------------------------------------------------------------------79
Figure 46. SD Playback / Playback List View – Playback----------------------------------------------------80
Figure 47. System / Security – Users -----------------------------------------------------------------------81
Figure 48. System / Security – Users / Add User -----------------------------------------------------------82
Figure 49. System / Security – Users / Modify User --------------------------------------------------------83
Figure 50. System / Security – HTTPS ------------------------------------------------------------------------84
Figure 51. System / Security – IP Filtering -------------------------------------------------------------------86
Figure 52. System / Date & Time ------------------------------------------------------------------------------87
Figure 53. System / Network – Basic -------------------------------------------------------------------------89
Figure 54. System / Network – DDNS ------------------------------------------------------------------------91
Figure 55. System / Network – RTP ---------------------------------------------------------------------------92
Figure 56. System / Network – UPnP -------------------------------------------------------------------------94
Figure 57. System / Network – QoS -------------------------------------------------------------------------95
Figure 58. System / Language ---------------------------------------------------------------------------------96
Figure 59. System / Maintenance -----------------------------------------------------------------------------97
Figure 60. System / Support -----------------------------------------------------------------------------------99
Figure 61. About ------------------------------------------------------------------------------------------------100

11

DESCRIPTION

-------------------------------------------------------------------------------------------------------------------------------------

The NXC Series camera is an internet protocol based megapixel network camera with a built-in web
based viewer on Internet Explorer®. The camera has a connection feature for third-party
applications and compatible with supplied Utility software for easy installation and Client software to
search, configure, manage, live view, record and playback.

The camera supports dual compression formats and multiple streaming simultaneously. The two
standard compression formats include H.264 and MJPEG. The multiple streams can be configured to
a variety of resolutions, bit rates and frame rates.
The camera uses 1/2.5 inch CMOS sensor and complies with CS mount lens and also supports PoE
(Power over Ethernet), DC12V, and AC24V.

Models

NXC-1401M NXC Series, 1 Megapixel, 30ips@1280x720
NXC-1402M NXC Series, 2 Megapixel, 15ips@1600x1200
NXC-1301M NXC Series, 1 Megapixel, 30ips@1280x720, Day/Night
NXC-1302M NXC Series, 2 Megapixel, 15ips@1600x1200, Day/Night

Key Features

- HDTV Video Quality

The NXC Series are capable of providing the outstanding image quality with HDTV performance and

profiles (High, Main, and Baseline) in H.264 compression.

- Multiple Streaming

Each stream can be programmed independently and transmitted using different configurations.

- ROI (Region of Interest)

ROI features that transmit specially selected area in the primary stream using different FPS,

Resolution, Bit Rates and Picture Quality.

- Easy Focus

Easy Focus helps to reduce the installation efforts especially video image focusing of the camera.

- Dual Codec (H.264, MJPEG)

The NXC Series supports two standard compressions formats H.264 and MJPEG.

12

- Digital PTZ

Supports maximum 10x digital zoom.

- Intelligent Video Motion Detection

The NXC Series offers intelligent & sophisticated video motion detection for each multiple streams.

- Triple Power (Power over Ethernet, DC12V, AC24V)

This camera supports Power over Ethernet (PoE), which supplies power to the camera through the

network. If the network has no PoE, connect a DC12V or AC24V power connector.

- Day and Night

The NXC Series provide clear monitoring images even in low light conditions using IR-cut filter.

- SD Local Recording

The NXC Series provides local video recording function. When camera detects video motion or
alarm events or manual trigger, it can record video stream by itself.

- Voice Alert Linked to Alarm Detection

The NXC Series can play the audio file stored in the camera in synchronization with alarm detection
by the sensor input or the motion detection function.

- Network Flow Control

The NXC Series provides a flow control function which enhances network efficiency by significantly
restricting user video streams with designating the maximum bandwidth.

- ONVIF Certificate

The NXC Series network camera complies with the ONVIF certificate. ONVIF (Open Network Video Interface
Forum) is an open industry forum for the development of a global standard for the interface of network video
products.

Components

Quantity Description

1 Camera
1 Installation CD

1 C- Mount Ring
1 Auto DC-Iris Connector

NOTE

Lens, installation hardware and Adapter for DC12V / AC24V are not supplied.

13

Camera Layout

RJ-45 connector: Supplies power to the camera through the network using PoE. If PoE is

not available, supplies DC12V or AC24V power source to the POWER connector.

ETHERNET link indication LED: Flashes green to indicate that data is being TX/RX by the

camera.

ETHERNET activity indication LED: Glows solid amber to indicate that a live connection is

established.

STATUS indication LED: Flashes amber about one time per second to indicate normally

working and flashes green about 2~3 time per second while upgrade.

POWER indication LED: Glows solid red if power is supplied properly.

SPEAKER connector: Connect external speaker for audio output.

MIC connector: Supplies external microphone as an audio input source.

POWER connection: Supplies DC12V or AC24V as the power source comply with Class2.

14

RESET button: Restores the camera’s factory default settings. This button is recessed. Use a

small tool, such as a paper clip, to press the reset button.
Please take steps as follows:

1. Power off

2. Press and hold the RESET button

3. Supply the camera with power

4. Hold the RESET button for 15 seconds

ALARM connection: Connect one or two physical alarm input signal into the device and one

alarm output signal that can be used to control an external alarm circuit.

BNC connector: Connect BNC cable for composite video output.

INSTALLATION TOP STAND connector: 0.25 Inch (0.64cm) UNC-20 screw, top of camera

housing.

INSTALLATION BOTTOM STAND connector: 0.25 Inch (0.64cm) UNC-20 screw, bottom

of camera housing.

FOCUS ADJUSTING / FIXING screw: Tighten this screw after focus the lens of a camera.

AUTO IRIS LENS connector: Connect the DC auto iris lens 4-pin connector into this

connector to control the amount of light allowed through the lens.

CS MOUNT LENS: connection: Attach the CS type lens.

RS485 connection: Connect RS485 compatible device for PTZ control.

SD Card: Insert SD card for local recording.

15

INSTALLATION

-------------------------------------------------------------------------------------------------------------------------------------

Before Installation

Before installing the camera, thoroughly familiarize yourself with the information in this section of

the manual.

- Recommends connecting the camera to a network that use a DHCP (Dynamic Host Configuration

Protocol) server to address devices.

- To ensure secure access to the IP camera, place the camera behind a firewall when it is

connected to a network.

NOTES

- Use megapixel lens for higher image quality.

- The NXC Series are designed and tested to deliver optimal image quality using megapixel lens.

- If the standard definition lens was installed on megapixel camera, the image quality will be poor

than expected.

- Recommend to install the megapixel lens from the following lens manufactures.

-- TAMRON

-- COMPUTAR

-- FUJINON

Starting Installation

1. Install the Lens

- Be careful the lens does not touch camera sensor when installer try to enter the lens into camera.

- Install manual lens or DC auto iris lens.

- If DC auto iris lens needs to install, connect DC auto iris 4-pin connector into iris drive connector

located on the side of the camera.

2. Mount the camera

The camera can be mounted from both top side and bottom side.

3. Connect other peripheral devices

Connect the other peripheral devices such as Alarm, Audio and BNC connector.

4. Supply the camera with power.

- If PoE is not available, connect DC12V or AC24V wires to the camera power connector. Be careful

when DC12V wiring especially the direction of positive and negative. Use power supply compatible
with FCC Class2.

16

- This camera complies with IEEE802.3af standard. It means that the power for this camera can be

supplied from Ethernet cabling without additional power supply. This can be reducing the
installation efforts.

- The camera will complete a configuration processing within approximately 40 seconds. The amber

LED flashes one time per second after the configuration processing are complete.

5. View the camera image

View the camera image using BNC connector or built-in web browser or supplied Client software.

NOTE

This camera will autosense and work with either a straight Ethernet cable or crossover Ethernet
cable.

DC Auto Iris Lens Installation & Adjustment

The camera supports DC-type auto iris lenses. Perform the following steps to install and adjust a
DC-type auto iris lens.

- Solder the lens control wires to the connector supplied with the camera.

Figure 1. 4-Pin iris driver connector

- Attach the DC-type auto iris lens to the lens mount on the front of the camera.

- Plug the connector into the auto iris jack on the side of the camera. The connector is polarized

and can be inserting into the iris jack one way.

Figure 2. DC auto iris Lens connection

17

Audio Connection

This camera supports bidirectional audio. Install the microphone and speaker which has an amplifier
capability.

Figure 3. Audio connection

External Speaker

External Microphone

Alarm Connection

The camera provides two alarm input for external signaling devices and one alarm output for
activating external device. Both Normally Open and Normally Closed devices are supported. Be
consult before alarm device installation how to wire between the camera and alarm devices.

Figure 4. Alarm connector

Alarm Input 1

Alarm Ground

Alarm Input 2

Alarm Output

Alarm Ground

RS485 -

RS485 +

18

OPERATION

-------------------------------------------------------------------------------------------------------------------------------------

Before starting the camera, installation must be complete. The camera completes a configuration
sequence within approximately 40 seconds when power is supplied. The amber LED of this
megapixel camera flash one time per second indicating the configuration sequence is complete.

NOTES

- If the DHCP is enabled but the camera is not connected to a DHCP server, the camera will be set

default IP 192.168.30.220 and try to get IP from DHCP server about every two seconds.

- Network and processor bandwidth limitations might cause the video stream to pause or appear

pixilated when an increased number of Web-interface users connection to the camera. Decrease
the images per second, resolution, compression, or bit rate settings of the Web-interface video
streams to compensate for network or processor limitations.

Minimum conditions for using web browser

The minimum system requirements to use a Web browser with this IP camera are as follows:

- CPU: Pentium® 4 microprocessor, 2.0GHz

- Operational System: Windows XP® or Windows Vista® or Windows7®

- System Memory: RAM 512 Mbyte

- Ethernet: 100 Mbit

- Video Resolution: 1024(Horizontal) x 768(Vertical) pixels or higher

- Internet Explorer® 7 or later

- ActiveX® 1.0.0.13 or later

Accessing the IP camera

1. Open Web browser

- Double click Internet Explorer® icon.

2. Type IP address

- Type the camera’s IP address in the Internet Explorer® address bar.

- The default IP address is

192.168.30.220

NOTES

- If you do not know the camera’s IP address, install the SmartManager® utility software available

on the CD supplied with the product. The utility software will locate the assigned Model name,
Host name, MAC address, IP address, Version and others.

- Refer to the SmartManager® utility software manual for more detail.

3. Log On to the camera

- Click the Live View icon for default live image view or the Setup icon to change the configuration

values.

19

Main Menu

Figure 5. Main menu

The dialog box will be appears.

- Type User ID and Password in the dialog box. The default User ID and Password is

admin

.

NOTE

For security purposes, be sure to change the password after you log on for the first time.

20

LIVE VIEW

-------------------------------------------------------------------------------------------------------------------------------------

The Live View page provides you to select the properties of video source. You can view the live
image from this page and also access the Setup menu and operate the main functions.

Figure 6. Main Live View Page

21

Live Video Page Icons

Hide Main Icons: Hides main icons in the live view page.
Show Main Icons: Shows main icons in the live view page.

Live view: Displays live video stream.

Setup: Enters setup menu.

Help: Shows helpful information.

Source: Specify the viewable video stream source to display in live view page.

View Size: Specify the viewable video size to display in live view page.

Stream Type: Specify the internet protocol to display in live view page.

ROI View: Specify the specially selected area to transfer using different stream feature in the

primary video image. ROI is an abbreviation for “Region of Interest”.

Preset: Specify the Preset. This icon is inactivated if the PTZ settings are not set.

Pause: Pause the live video stream.

Snapshot: Take a picture of the video image currently on display. Supports the origin image

size view, Print, and Save feature.

Digital Zoom: Supports a digital zoom in live video image.

Full Screen: Expands video image to the entire screen area.

Manual Trigger: Activates the Alarm Out signaling manually.

PTZ: Activates a pop-up window for Pan, Tilt and Zoom control.

Speaker: Adjusts the volume of Speaker and switch the sound on / off.

Microphone: Adjusts the volume of Microphone and switch the sound on /

off.

22

SETUP

-------------------------------------------------------------------------------------------------------------------------------------

The SETUP pages provide you to manage the camera and change the setting values. For the easy
and quick access the video, the setup menu is configured two parts, which are Basic Configuration
and advanced configuration. The Basic Configuration menu allows you to setup Users, basic
Network and Image. The remaining configuration parts help to setup user dependent values and
provide more advanced settings.

Basic Configuration

Basic Configuration supply user to access the camera image using minimum setting. Also it shows
the camera basic information such as Model name, Firmware version and MAC address.

Figure 7. Basic Configuration

NOTE

The setting menu might not be available if the user does not have the permission to access this

feature. The only required setting is the IP address, which is set on the Network page. All other
settings are available with default values and optional.

23

Users

Use the Users tab to manage user permission to access the camera.

Figure 8. Basic Configuration / Users

User Setting: Click the Enable anonymous viewer login checkbox to enable anonymous user

login to the camera. The default setting is disabled.

User List Setting:

User accounts can be added or modified or removed. The authority

depends upon user group automatically and shows the permission status to access the menus.
The default user name / password is

admin

.

User Name: Shows the name which registered to access the camera.
User Group: Shows the assigned permission given to users.
Authority: Shows the permission status to access the menus.

24

Click the Add, Modify, or Remove button for managing user account.

Figure 9. Basic Configuration / Users / Add User

To add a new user:

1. Click the Add tab, and then new pop-up window appears.

2. Click in the User name box and type a new user name (1 to 14 alphanumeric characters). User

names are not case sensitive.

3. Click in the Password box and type a password (1 to 8 alphanumeric characters). Passwords are

case sensitive.

4. Click in the Confirm password box and retype a password.

5. Click in the User group box and select one of the groups you wish to assign to the user.

6. Click the OK button to save the settings and add a new user.

25

Figure 10. Basic Configuration / Users / Modify User

To modify a user:

1. Select one of the User Name in the User List Setting you want to modify.

2. Click the Modify tab, and then new pop-up window appears.

3. Click in the Password box and type a password (1 to 8 alphanumeric characters). Passwords are

case sensitive.

4. Click in the Confirm password box and retype a password.

5. Click in the User group box and select one of the groups you wish to assign to the user.

6. Click the OK button to save the settings and modify a user.

NOTE

The user name can’t be modified.

To remove a user:

1. Select one of the User Name in the User List Setting you want to remove.

2. Click the Remove tab. A dialog box appears with confirmation message.

3. Click the OK button. The user profile is removed from the User List Setting profile.

NOTE

The admin user name can’t be modified.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

26

Network

Use the Network tab to manage basic network settings.

Figure 11. Basic Configuration / Network

IP Address Configuration: The DHCP (Dynamic Host Configuration Protocol) server has

a feature that automatically assigns an IP address to the device if there is a device on the network.

Obtain IP address via DHCP: Select the checkbox if you want to assign the IP address from

DHCP server automatically, and then the remaining setting are read-only text.

Use the following IP address: Select the choice box if you want to assign the IP address

manually.

IP address: The address of the camera connected to the network. Specify a unique IP address

for this network camera.

Subnet mask: The address that determines the IP network that the camera is connected to

(relative to its address). Specify the mask for the subnet the network camera is located on.

Default router:

The router that accesses other networks. Specify the IP address of the default

router (Gateway) used for connecting devices attached to different networks and network segments.

27

DNS Configuration: DNS (Domain Name Service) provides the translation of host names to

IP addresses on your network.

Obtain DNS server via DHCP: Select the choice box if you want to use the DNS server

settings provided by the DHCP server automatically, and then the remaining setting are read-only
text.

Use the following DNS server address: Select the choice box if you want to use the desired

DNS server manually.

Domain name: Enter the domain to search for the host name used by the network camera.
Primary DNS server: Enter the IP address of the primary DNS server.
Secondary DNS server: Enter the IP address of the secondary DNS server.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

Image

Use the Image tab to adjust the camera image setting value and orientation.

Figure 12. Basic Configuration / Image

28

Image Appearance: The image appearance allows you to adjust the camera setting

parameters and change the camera orientation. All of parameters are recommended to be
modifying for good image quality suitable for installation place.

Brightness: The image brightness can be adjusted in the range 0-20, where a higher value

produces a brighter image. The default setting is 6.

Gamma: Adjusts the details in the light and dark areas of the scene. Gamma can be adjusted in

the range 0.2-1.2, where a lower value expose more detail in the light area of the scene and a
higher value expose more detail in the dark area of the scene. The default setting is 0.5.

Contrast:

Controls the gradations between the darkness and lightest portions of the scene. The

contrast can be adjusted in the range 1.0-2.0. The default setting is 1.0.

Saturation: Controls how intense or vivid the colors are in a scene. The saturation can be

adjusted in the range 0-16. The default setting is 8.

Sharpness: Controls the clarity of detail in a scene. The sharpness can be adjusted in the range

0-20. The default setting is 12.

Enable flip image: Rotate the camera image 180 degrees vertically.
Enable mirror image: Creates a mirror image by rotating the camera image 180 degrees

horizontally.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.

29

Audio

Use the Audio tab to manage the basic audio settings for the camera.

Figure 13. Basic Configuration / Audio

Audio Setting: Click the Enable audio checkbox to enable audio. This page describes how to

configure the basic audio settings for the camera. This camera supports the audio full duplex that
can be transmits and receives audio in both directions at a time.

Compression type: G.711 is the international standard for encoding wired-telephone audio on

64kBit/s channel. It is a PCM (Pulse Code Modulation) scheme operating at 8 kHz sample rate. The
default setting is G.711 µ-law.

Sample rate: Indicates the number of times per second the sound is sampled. The default

setting is 8 kHz.

30

NOTE

G.711, also known as Pulse Code Modulation (PCM), is a very commonly used waveform codec.
G.711 uses a sampling rate of 8,000 samples per second, with the tolerance on that rate 50 parts
per million (ppm). Non-uniform quantization (logarithmic) with 8 bits is used to represent each
sample, resulting in a 64 kbit/s bit rate. There are two slightly different versions; μ-law, which is
used primarily in North America, and A-law, which is in use in most other countries outside North
America. G.711 μ-law tends to give more resolution to higher range signals while G.711 A-law
provides more quantization levels at lower signal levels.

Audio Input: Adjusts the audio volume especially from the Mike.

Input volume: The Input volume can be adjusted in the range from -21.00 to 21.00 dB. The

default setting is 0 dB. Click the Mute box if you do not want the audio input.

Audio Output: Adjusts the audio volume especially to the Speaker.

Output volume: The Output volume can be adjusted in the range from -18.1 to 6.0 dB. The

default setting is 0 dB. Click the Mute box if you do not want the audio output.

- Click the Save button to save the settings, or click the Reset button to clear all of the information

you entered without saving it.