The Light pack contains:
The following tools may be required:
1805 range - 1 and 2 Light Switched Wall brackets.
Safety Warnings
INSTRUCTION M ANUAL
These products are only suitable for connection to a 240V~50Hz supply in accordance with current
IEE wiring Regulations and should be installed in accordance with local Building Regulations and
are for Domestic wall use only. They are not suitable for bathroom use.
The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp
miniature circuit breaker).
If in doubt we recommend you contact a qualified electrician. Before installing your light fitting
always:
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit
breaker before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
Never fit bulbs of a higher wattage or of a type other than those specified on the label as this may
cause overheating and damage the fitting.
Be careful during handling and maintenance to avoid breakage or damage to the fitting.
The bulbs become hot during use so please switch off and allow 10 minutes to cool before replacing
bulbs or cleaning the fitting.
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
If any modification is made it will invalidate the warranty and may render the product unsafe.
Before you start
Please read these instructions carefully before fitting your new light and retain for reference.
Make sure that there are no pipes or cables beneath the mounting surface.
Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly.
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.
This type of Light Fitting may be connected to a Dimmer if a Tungsten incandescent bulb is used. If
a CFL type bulb is fitted then these cannot (generally) be controlled by a dimmer.
Switched Light fitting and mounting bracket.
Terminal connection block(s).
Shade ring..
Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
1
Assembly/ User Instructions
1. Decide on the position of your
S030 282
Diagram A
Diagram B
WIRING DETAILS
These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician. The 1 arm wall
bracket is shown here but the same gene ra l instruction applies to the 2 arm fitting also.
light fitting. Ensure there is a
solid mounting surface,
preferably a brick or block wall
and ensure that there are no
cables or pipes beneath the
surface. If the wall is timber
frame and plasterboard then
please use appropriate fixings.
Wall plugs are shown here –
Diagram A. Ensure the fixings
used can support the weight of
the wall light.
2. Diagram A. Remove the fixing
bracket, by undoing the 2
bracket screws (1), retain these
for re-use.
3. Use the fixing bracket, as a
template to mark the screw
holes. Make sure the bracket is
horizontal. Fix the bracket to the
wall – the use of plugs (2) and
screws (3) are shown here.
4. Diagram B. Support your fitting
and connect the house wiring to
the terminal block (4). NOTE:
This is a Class I fitting and
must be earthed. See wiring
details.
5. Re-position the fitting over the
wall bracket and secure with the
2 back plate / bracket screws,
removed in 2 above. Make sure
that all the internal cables and
connections are inside the back
plate taking care not to trap or
strain the internal cables.
6. Diagram C. Position the shades
(5) over the lamp holders and
secure with the shade ring (6)
being careful not to over tighten
and damage the shades.
7. Fit the bulbs (7). NOTE; Never
fit bulbs of a higher wattage
than those specified on the
label (as these may cause
overheating and damage the
fitting).
8. Turn on the power and test
using the pull switch.
Endon Lighting, LS9 0SE
20150324
2
Loading...