Enda ETC1311, ETC1311-FE-230VAC, ETC1311-RT-230VAC, ETC1311-K-230VAC, ETC1311-FE-24VAC User manual

english

Read this document carefully before using this device. The guarantee will be expired by damaging of the device if you don't attend to the directions in the user manual. Also we don't accept any compensations for personal injury, material damage or capital disadvantages.

ENDA ETC1311 DIGITAL THERMOSTAT

Thank you for choosing ENDA ETC1311 temperature controller.

*35 x 77mm sized.

*On-Off control.

*TC Typ “J” or “K” or Pt100 input.

*Temperature compensation.

*In the case of probe failure, heating can be selected on, off or periodical running.

*Upper and lower limits of the setpoint can be adjusted.

*Set value can be adjusted by using single key.

*Having CE mark according to European Norms.

Order Code : ETC1311-••-••••••-•

1

2

3

OUT

°C

PRG

SET

ENDA

ETC1311

1 - Input		2 - Supply Voltage		3 - Output
FE.....	Fe-Const (J)	230VAC	...230V AC	P.........	Relay-16A
RT.....	Pt100	24VAC.....	24V AC	None...	Relay-8A
K.......	NiCr-Ni (K)	12VAC.....	12V AC	SSR....	Logic output
		SM...........	9-30V DC / 7-24V AC

Attention !

ENDA ETC1311 is intended for installation in control panels. Make sure that the device is used only for intended purpose. The electrical connections must be carried on by a qualified staff and must be according to the relevant locally applicable regulations. During an installation, all of the cables that are connected to the device must be free of energy. The device must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded. The cables should not be close to the power cables or components.

ENDA INDUSTRIAL ELECTRONICS
ETC1311-K-230VAC
DIGITAL THERMOSTAT
							SN: XXXXXXXXX
<![if ! IE]> <![endif]>HEATOUT	<![if ! IE]> <![endif]>250VAC8A	<![if ! IE]> <![endif]>RESISTIVELOAD	<![if ! IE]> <![endif]>230VAC+10%-20%	<![if ! IE]> <![endif]>50/60Hz 4VA						K (NiCr-Ni)
										-	+
1	2	3	4	5	6	7	8	9	10	11 12

ENDA INDUSTRIAL ELECTRONICS
	ETC1311-FE-230VAC-P
	DIGITAL THERMOSTAT
								SN: XXXXXXXXX
<![if ! IE]> <![endif]>HEATOUT	<![if ! IE]> <![endif]>240VAC16A RESISTIVELOAD			<![if ! IE]> <![endif]>230VAC+10%-20%	<![if ! IE]> <![endif]>50/60Hz 4VA					J (Fe-CuNi)
										-	+
1	2	3	4	5	6	7	8	9	10	11 12

ENDA INDUSTRIAL ELECTRONICS
ETC1311-RT-12VAC
DIGITAL THERMOSTAT
							SN: XXXXXXXXX
<![if ! IE]> <![endif]>HEATOUT	<![if ! IE]> <![endif]>250VAC8A	<![if ! IE]> <![endif]>RESISTIVELOAD	<![if ! IE]> <![endif]>12VAC±10%	<![if ! IE]> <![endif]>50/60Hz 4VA						Pt100
1	2	3	4	5	6	7	8	9	10	11 12

Equipment is protected throughout		Holding screw 0.4-0.5Nm
by DOUBLE INSULATION.

NOTE:

Fuse

Note:

SUPPLY:

F 100 mA

Switch

1) Mains supply cords shall meet the requirements of

250V AC

4

Line

IEC 60227 or IEC 60245.

184-253V AC

230V AC

50/60Hz 3VA

5

2) In accordance with the safety regulations, the power

Neutral

Supply

supply switch shall bring the identification of the

Fuse should

relevant instrument and it should be easily

be connected Cable size: 1,5mm²

accessible by the operator.

<![if ! IE]>

<![endif]>up to date: 01022014, modification reserved and can be change any time previous notice !

Technical Specifications

ENVIRONMENTAL CONDITIONS

Ambient/storage temperature	0 ... +50°C/-25 ... 70°C (with no icing)
Max. relative humidity	80%, up to 31°C decreasing linearly 50% at 40°C
Rated pollution degree	According to EN 60529	Front panel : IP65
		Rear panel : IP20
Height	Max. 2000m

Do not use the device in locations subject to corrosive and flammable gasses.

ELECTRICAL CHARACTERISTICS

Supply voltage /	230VAC +10%/-20%, 50/60Hz, 24VAC±10%,50/60Hz or 24Vac/dc (9-30Vdc or 7-24Vac)
Power consumption	Max. 4VA
Wiring	2.5mm² screw-terminal connections.
Scale	TE Typ “J” or “K”: 0 ... +600°C / Pt100: -100...600°C
Sensitivity/Accuracy	± 0.5% (of full scale) / ±1 digit
Indicator	3 digits, 14mm, 7 parts red LED
EMC	EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B is satisfied for EMC tests.
	The device is designed to operate in controlled electromagnetic environment)
Safety requirements	EN 61010-1: 2001 (Pollution degree 2, overvoltage category II)

OUTPUT

HEAT OUT	For ETC1311-XX ; Relay: 250V AC, 8A(for resistive load), NO+NC.
	For ETC1311-XXP ; Relay: 250V AC, 16A(for resistive load), NO.
Life expectancy for relay	For ETC1311-XX ; Mechanical 30.000.000; Electrical 100.000 operation.
	For ETC1311-XXP ; Mechanical 30.000.000; Electrical 30.000 operation.

CONTROL

Control type	Single-setpoint control
Control algorithm	On-Off control
Hysteresis	Adjustable between 1 ... 20°C.

HOUSING

Housing type	Suitable for flush-panel mounting.
Dimensions	W77xH35xD71mm
Weight	Approx. 250g (after packing the device and a probe)
Enclosure material	Self extinguishing plastics

While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.

Dimensions

	77mm
<![if ! IE]> <![endif]>35mm	OUT
	SET
	°C
	PRG

ENDA										ETC1311
1112		10	9	8	7	6	5	4	3	2	1
+	-
K(NiCr-Ni)							<![if ! IE]> <![endif]>4VA 50/60Hz	<![if ! IE]> <![endif]>20%- +10% AC 230V		<![if ! IE]> <![endif]>8A AC 250V LOAD RESISTIVE	<![if ! IE]> <![endif]>OUT HEAT
									SN:XXXXXXXXX
							DIGITALTHERMOSTAT
								ETC1311-K-230VAC
				INDUSTRIALELECTRONICS
										ENDA

For removing mounting clamps:

Push out the flush-mounting clamp in direction 1 as shown in the figure below. Then, pull out the clamp in direction 2.

Depth
71mm	5mm

					Flush mounting				2	Panel
						clamp				Rubber
Flush mounting										packing
clamp
					Panel cut-out			Note :1) Panel thickness
1					71mm				should be maximum
									7 mm.
									2) If there is no 60mm
<![if ! IE]> <![endif]>29mm									free space at the back
									side of the device, it
									would be difficult to
									remove it from the
									Panel

	1./2 ETC1311-E
SURAN Industrieelektronik
Dettinger Str. 9	Tel.: [phone] / 625 617 E-mail : [e-mail]
D-72160 Horb a.N.	Fax: [phone] Internet : www.suran-elektronik.de