Enda ET2411, ET2411-230-08, ET2411-012-08, ET2411-024-08, ET2411-SM-08 User manual

8 680 40 7 71 52 99

8 680 40 7 71 53 67

8 680 40 7 71 53 50

8680407715299

english

Read this document carefully before using this device. The guarantee will be expired by device
demages if you don't attend to the directions in the user manual. Also we don't accept any
compensations for personal injury, material damage or capital disadvantages.

ENDA 2411 ON/OFF HEAT CONTROLLER ET

Thank you for choosing ON/OFF Heat Controller.ENDA ET2411

- 77 x 35mm sized.

- Single NTC sensor input.

- Zero point input shift.

- Selectable heating or cooling control for C1 relay output.

- Selectable heating or cooling control.

- In the case of sensor failure, relay state can be set to ON or OFF.

- Upper and lower setpoint limits can be adjusted.

- Temperature unit can be selected as °C or °F.

- CE marked according to European Norms.

1 - Supply Voltage

230... 230V AC

Order Code : ET2411 - -

1

.....

24........24V AC

0 /DC

2

012........12V AC/DC

SM.........7-24VAC/9-30VDC

ENDA ET2411 is intended for installation within control panels. Make sure that the device is used only for
intended purpose. The shielding must be grounded on the instrument side. During an installation, all of the
cables that are connected to the device must be free of electrical power. The device must be protected against
inadmissible humidity, vibrations, severe soiling. Make sure that the operation temperature is not exceeded.

All input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables.
These cables should not be close to the power cables or components. The installation and electrical connections must
be carried out by a qualified staff and must be according to the relevant locally applicable regulations.

ENDAINDUSTRIAL ELECTRONICS

ET2411-230-08
DIGITAL THERMOSTAT

Made in Turkey

250V AC 8A

RESISTIVE LOAD

C1

1 2 3 4 5 6

NOTE:

SUPPLY:

184-253V AC
50/60Hz 3VA

up to date: 25.03.2019, modification reserved and can be change any time previous notice !

5
6

7 8 9

Line

Neutral

SN: XXXXXXXXX

10

ENDAINDUSTRIAL ELECTRONICS

ET2411-230-16
DIGITAL THERMOSTAT

Made in Turkey

250V AC 16A

RESISTIVE LOAD

NTC

C1

12

Fuse

F 100 mA

250V AC

1 2 3 4 5 6

Switch

Cable size: 1,5mm²

230V AC
Supply

11

Equipment is protected throughout
by DOUBLE INSULATION

Fuse should
be connected

SN: XXXXXXXXX

7 8 9

11

10

Note:

1) Mains supply cords shall meet the requirements of
IEC 60227 or IEC 60245.

2) In accordance with the safety regulations, the power
supply switch shall bring the identification of the
relevant instrument and it should be easily
accessible by the operator.

SURAN Industrieelektronik

Dettinger Str. 9
D-72160 Horb a.N.

Tel.: [phone] / 625 617 E-mail : [e-mail]

Fax: [phone] Internet : www.suran-elektronik.de

C1

°F

ENDA

2 - Relay Current Selection

05.....5A Re

08.....8A

16...16A Relay Output

ENDAINDUSTRIAL ELECTRONICS

ET2411-SM-05
DIGITAL THERMOSTAT

Made in Turkey

250V AC 5A

RESISTIVE LOAD

NTC

12

C1

1 2 3 4 5 6

Holding screw

0.4-0.5Nm.

lay Output

Relay Output

7 8 9

°C

SET

SET

ET2411

R HS
Konform

SN: XXXXXXXXX

NTC

11

10

12

TECHNICAL SPECIFICATIONS

INPUT

Input Type
NTC Sensor Typ 103AT-2

at 25 °C - 10 kOhm

Ambient/Storage temperature

Relative Humidity

Protection Class

Height

Do not use the device in locations subject to corrosive and flammable gasses.

EN 60751

0 ... +50 /
Max. humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C.
According to EN60529; Front panel: IP65 Rear panel : IP20
Max. 2000m

°C °C without icing( )

-25... +70

S alc e Range

- ... 0 °C -76.0...302.0°F60.0 15 .0

ENVIRONMENTAL CONDITIONS

ELECTRICAL CHARACTERISTICS

Supply
Power onsumptionC

Wiring
Line Resistance
Data Retention
EMC
Safety Requirements
Indicator

230V AC + % - %, 50/60Hz 24V AC %10 20 or 12/ /DC 10

Max. 3 VA
Power connector : 2.5mm² screw-terminal, Signal connector : 1,5mm² screw-terminal conenction.
Max. 100ohm
EEPROM ( 10 )Min. years

EN 61326-1 : 2013 (Performance criterion B is satisfied for EN 61000-4-3)
EN 61010-1 : 20 (Pollution degree 2, overvoltage category II) 10

4 digits, 12.5mm, 7 segment red LED

OUTPUT

C1 Output

Life Expectancy for Relay

For 5A Models : 250V AC, 5A (resistive load), NO control output.
For 8A Models : 250V AC, 8A ( ), NO and NC control output.resistive load
For 16A Models : 250V AC, 16A ( ), NO control output.resistive load

For 5A Models : 5. Switching for no-load operation; 100.000 switching for 5A resistive load at 250VAC. Mio.
For 8A Models : 30. Switching for no-load operation; 300.000 switching for 8A resistive load at 250VAC. Mio.
For 16A Models : 30. Switching for no-load operation; 100.000 switching for 16A resistive load at 250VAC. Mio.

CONTROL

ontrolC Type
Control Algorithm

A/D Converter

Hysteresis

Single and alarm .-setpoint control

12 bit , sampling time.resolution 100ms
Adjustable between 0.1 and 20.0°C/F.

HOUSING

Housing Type
Dimensions
Weight
Enclosure Materials

While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.

according to DIN 43 700.Suitable for flush-panel mounting
5 1W77xH3 xD6 mm
Approx. 215g (A )fter packing

Self extinguishing plastics

Dimensions

77mm

°F

ENDA

12

C1

°C

SET

SET

ET2411

10

11

7 8 9

NTC

SN: XXXXXXXXX

1 2 3 4 5 6

C1

RESISTIVE LOAD

250V AC 8A

Made in Turkey

DIGITAL THERMOSTAT
ET2411-230-08

ENDAINDUSTRIAL ELECTRONICS

For removing mounting clamps:

- Push the flush-mounting clamp

in direction as shown in the
figure below.Then,pull
out the clamp in direction .12

Connection

Cable

Flush mounting

clamp

Panel cut-out

1

2

71,5mm

Accuracy

± 1% (for full scale) ±

Depth

61mm

Flush mounting

clamp

1) Panel thickness should

Note:

be maximum 7mm.

2) If there is no 60mm free
space at the back side of
the device,it would be
difficult to remove it from
the panel.

ET2411-E-25032019

1. / 2

Panel

1 Digit

5mm

Rubber

Packing

t

Measured temperature

SET

105 C1.SE.

When this button is pressed

message is appeared

C.SEt

and

temperature setpoint

adjustment mode is entered.

If key is pressed while holding down key,
then Programming Menu is entered.

Default value

100

SET

C1.Cn.

C1..L.L.= Control set point lower limit for C1

C1..L.L.

C1..H.L.

C1.Hy.

Modification Of Parameter Diagram

SET

Wh holding key, parameter and
,

ile down value blinks by

using keys the requested value can be adjusted.

If key is pressed and held 0.6 seconds, the value of the
selected parameter increases rapidly. If waited enough,the
value increases a hundred at each step. After 1 second,
following the release of the key, initial increasing condition is
returned. The same procedure is valid for the decrementing.

output.
It can be adjusted between -60.0 and

parameter value.

C1H.L.= Control set point upper limit for C1
output.

It can be adjusted between 150.0 and
parameter value.

C1.Hy. = Output hysteresis value.
It can be adjusted between and .0.1 20.0 °C

SET SET

SET

Programming Diagram

Running Mode

C1 Set value

100

Temperature setpoint value is adjusted with buttons then,
when one of these buttons are pressed for the first time, blinking setpoint value appears.

SET

101

102

101

Programming Menu

SET

ConF.

Default

Value

C1.H.L.

C1.L.L.

HEAt

°C

no

0

ERROR MESSAGES

pfa

----

____

Sensor is broken

Temperature value is
higher than the scale

Temperature value is
lower than the scale

C.tyP.

Unit.

d.P.

oFFs.

C1.E.S.

C.typ. = Control type selection.
C.typ. HEAt

=

C.typ. CooL

=

Unit = Temperature unit selection.
Unit. °C °F = Can be selected as or

d.P. = Decimal point display selection.

If , decimal value is not dotted.

d.P.. no

=

If = , decimal value is dotted.

d.P. YES

oFFS. = Offset .

Zero point shift value is added to the measured
value. This feature is used for eliminating the
measuring probe distance errors. It can be
adjusted between - and °C.

C1.E.S.

= C1 Output state in case of sensor failure.

on

= Output is ON in case of sensor failure.

off

= Output is OFF in case of sensor failure.

Heating control is selected.
Cooling control is selected.

value

20.0 20.0

If no key is pressed within 3 seconds, Running Mode is entered.

Entering Running Mode in Programming Mode :

In Programmin Mode, if no keys are pressed for 20 seconds information is
saved automatically and Running Mode is entered.
Alternatively, if and keys are pressed together, Programming Menu
is entered. In the Programming Menu, if key is pressed while holding

SET

down key, then Running Mode is entered.

SET

SECu.

Default

Value

0

P.YES

P.YES

P.YES

S.Cod.

C1.sc.

Co.sc.

C.S..sc.

S.Cod = Access code for security menu.

This parameter should be .411

When , if key is

s.co. = 0

pressed for 4 seconds while holding

SET

down key, then is seen
on display and the device is returned
to factory settings.

C1..sc. C1,Cn.

=

nonE

=

P.yEs

= Can be m ed

P. no

= .

..Co.sc. ConF.

=

nonE

= Invisible.

P.yEs

= Can be modified.

P. no

=

C.S.sc.

= security access level.

P.yEs

=

P. no

= Visible but can’t be modified

Security menu access level.

Invisible.

odifi .

Visible but can’t be modified

Configuration menu access level.

Visible but can’t be modified.

C1 set value

Can be modified.

SET

d.PAr.

.

2. / 2

ET2411-E-25032019