Enda ET2011-RT-230, ET2011, ET2011-T-230, ET2011-RT-110, ET2011-T-110 User manual

Read this document carefully before using this device. The guarantee will be expired by
damaging of the device if you don't attend to the directions in the user manual. Also we don't
accept any compensations for personal injury, material damage or capital disadvantages.

ENDA ET2011 PID TEMPERATURE CONTROLLER

Thank you for choosing 2011 temperature controller.ENDA ET

* x mm .77 35 sized
* Selectable dual-set value.

* Se tlectable thermocouple ypes or Pt100 input.(Selection must be
specified in order).
* (SELF TUNE).Automatic calculation of PID parameters.

Enter PID parameters of the system if they are known at the beginning.
Otherwise, Self-Tune should be activated.

* Soft-Start feature.
* Input offset feature.
* C/A2 Relay output can be programmable as alarm or control output.

* .Selectable SSR control output
* Selectable heating/cooling control.

* In the case of sensor failure periodical running or relay state can be
selected.

TECHNICAL SPECIFICATIONS

°F

ENDA

C/A2

SSR

°C

SET

SET

english

F

ET2011

Input type

Pt 100 Resistance thermometer
Pt 100 Resistance thermometer
J (Fe-CuNi) Thermocouple
K (NiCr-Ni) Thermocouple
T (Cu-CuNi) Thermocouple
S (Pt 0Rh-Pt) T1 hermocouple
R (Pt13Rh-Pt) Thermocouple

EN 60584
EN 60584
EN 60584
EN 60584
EN 60584

EN 60751
EN 60751 -200...600 °C

- ... 00 °C99.9 3 .0

0...1700

Temperature range

°C

0... 600

°C

0...1300

°C

0... 400

°C

0...1700

°C
°C

+32... +3092

ENVIRONMENTAL CONDITIONS

Ambient/storage temperature

Max. Relative humidity

Rated pollution degree

Height

Do not use the device in locations subject to corrosive and flammable gases.

0 ... +50 /°C -25... +70°C (with no icing)
80 up to 31 decreasing linearly 50 at 40.% %

According to EN 60529 Front panel : IP65
Rear panel : IP20

Max. 2000m

°C

ELECTRICAL CHARACTERISTICS

Supply
Power consumption

Wiring
Line resistance
Data retention
EMC

Safety requirements

230V AC +%10 -%20, 50/60Hz 24V AC %10, 50/60Hzor

Max. 5VA
Power : , Si : 1 ²connector 2.5mm²' screw-terminal gnal connector ,5mm screw-terminal conenction.
Max. 100ohm

EEPROM ( )minimum 10 years
EN 61326-1: 2006
EN 61010-1: 2010 (Pollution degree 2, overvoltage category II)

OUTPUTS

C/A2 output

SSR output
Life expectancy for relay

R : 250V AC, 8A (for resistive load), Selectable as NO+NC Control or Alarm2 output.elay
R : 250V AC, 16A (for resistive load), Selectable as NO Control or Alarm2 output.elay

Max 20mA 12Volt (as control output)
Withot load 30.000.000 mechanical operation; 250V AC, on the 8A resistive load 100.000
electrical switching

CONTROL

Control type
Control algorithm

A/D converter
Sampling time
Proportional band

Control period
Hysteresis
Output power

Single set-point and alarm control

1 bit2
00ms1

Adjustable between 0 and 100 . If Pb=0 , On-Off control is selected.% % %

and 250 secondsAdjustable between 1
1 and 50Adjustable between °C/F

The ratio of power at a set point can be adjusted between 0 and 100% %

HOUSING

Housing type
Dimensions
Weight
Enclosure material

While cleaning the device, solvents (thinner, benzine, acid etc.) or must not be used.corrosive materials

Suitable for flush-panel mounting according to DIN 43 700.
W77xH35xD71mm

Approx. 200g (after packing)
Self extinguishing plastics.

°F

- ...543 °F99.9 .0

-328...1112 °F
+32... +1112

+32... +2 237
+32... +752
+32... +3092

Accuracy

0,5% (of full scale)

0,5% (of full scale) 1 digit
°F
°F
°F
°F
°F

0, % ( )5 of full scale

0, % ( )5 of full scale

0, % ( )5 of full scale 1 digit

0, % ( )5 of full scale 1 digit

0, % ( )5 of full scale 1 digit

1 digit

1 digit
1 digit

SURAN Industrieelektronik

Dettinger Str. 9 / D-72160 Horb a.N

Tel.: [phone] / 625 617
Fax: [phone]

E-mail : [e-mail]
Internet : www.suran-elektronik.de

ET2011-E-06052019

1. / 4

SET

SET

If key is pressed while holding key, the programming mode is enabled.

SET

Con.o.

C.s.Lo.

C.s.Hi.

C. pb

C.Hys

C. ti

C. td

C. Ct.

C.p.st

C.E.p.s.

s.s.t.s.

C.typ

C.s.lo.= Control set point lower limit.(for

selected output)

Adjustable between 0 and C.s.Hi.

C.s.Hi.= Control setpoint upper limit.(for
selected output)

Adjustable between and Upper scale

value.

C. Pb

=
output)
Adjustable between .0 and .0.

C. Pb

= %0 On-Off

C.Hys

= Hysteresis of the output.(for
selected output)
Adjustable between 1 and 50 °C.

C. Pb

= 0,this parameter is active.

C. ti

==Integral time.(for selected output)
Adjustable between 0 and 100.0 minutes.

C. ti

C. Pb

parameter is different from “0”,this
parameter appears.

C. td

==Derivative time.(for selected output)
Asjustable between 0.00 and 25.00 minutes.

C. td

C. Pb

parameter is different from”0”,this
parameter appears.

C. Ct.

= Period time.(for selected output)
Adjustable between 1 and 250 second.

C. Pb

parameter is different is different
from“0”,this parameter appears.

C.p.st = The ratio of output power at the
setpoint.Adjustable between %0 and %100.

C.E.P.s. = The percentage of faulty sensor
selected output power.Adjustable between
%0 and %100.

Sst.S =Sofy starter timer set value

This parameter indicates the time to reach set point
value when the device is first enegised.
Adjustable between 0 and 250 minutes.
If 0 is selected, soft start feature will be enable and the
device reaches set point value quickly.

C.typ. = Control output type
C.typ. HEAt

=

C.typ. CooL

=

While the parameter names appear,if and
keys are pressed together, returns to the program
mode.

C.s.Lo.

Proportional band.(for selected

%0 %100

.0, control is selected.

0.0,integral impact is disable.

0.0, derivative time is disable.

Pb = 0, so start feature will be disable. Setting ft

means heatign control.

means cooling control.

Entering from the programming mode to the run mode:
If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered.

AL2.o.

A2.S.L

A2.S.H

A2.HY

A2.tP

A2.St.

A2.Er.

this parameter is seen and
adjustable only

if set co.SE SSR =

a2.s.l= Alarm2set value lower limit.
Adjustable between 0and A2.S.H

parameter value.

a2.s.H= Alarm2set value upper limit.
Adjustable between

parameter value and upper scale
value.

a2.Hy=.Hysteresis of the Alarm2
output
Adjustable between 1 and 50 °C.

A2.tp

= Function of Alarm type.
Four kinds of functions can be
selected.

indE.

= alarm

Independdnt

(Independent)

dE.

= Deviation

bAnd

= Band alarm (Band)

bAn.i

= Band with inhibition

A2.st.Hi= The state of Alarm2 output.

If A2 output is above the set

=
value. (on)
lo=If A2 output is above the set
value.(off)

A2.Er.on=

State of Alarm2 output in the

case of sensor failure.

2 output is probe failure (on).

= A

off= A2output is probe faiure (off).

A2.S.L

Alternatively, the same function occurs first pressing key and key is pressing programming mode is entered.Then and keys are pressing
together,data is recorded and running mode is entered.

Programming mode

SET

SET

ConF.

inp.t.

=

inp.t.

Unit

fltr.

2

C.o.sE

offs.

F.k.E.C.

m.SEt.

Input type selection.

FE.cn. nc.nA. c.cn.

= J type , = K type = T

p10.r. P13.r.

type =S type , = R type
thermocouple selection.
This parameter varies when changing
some parameters.

Unit = The temperature unit.
°C °F= °C, = °F

(This parameter varies when
changing some parameters.)

fLtr.= Coefficient of digital filter.
Filter for display value.
Adjustable between 1 and . If this parameter is 1,
digital filter runs most quick. If the parameter is ,
the filter run most slow. The value of parameter should
be increased in interference.

C.o.sE = Control output selection

C-A2

= C/A2 (Relay) output selection

SSR

= SSR output selection

oFfS. = Offset value.
Offset value is added to the measurement value.
Adjusted between -100 and +100°C.The normal value is 0.

F.kE.C. = Function key setting parameter
nonE

= Function key is off.

C2.S.A.

= The function key with 2.set value is used.

manu.

= Manual mode can be achieved with the function key.

dSP.o

= Device only the temperature display mode is entered

.

with function key.

m.SEt.

=

The percentage of manual output parameter.
Adjustable between %0 and %100.
This parameter allows manual adjustment of the output
power when the manual output selection.

C. Pb.

0=

200

, this parameter is not seen.

F

SET

S.tun.

St.Cu = Self tune control parameter.

s.t.Co.

200

SET

If both keys are pressed ,
message is displayed on the screen
and self tune process is started
automatically.

SET

If both keys are pressed,
message is displayed on the screen
and self tune process is stopped.

Selt tune begins when the measurement,
and measurement value

PIdt.

message
are shown alternately.Self tune process
completed automatically after the
parameter is done no and is entered to the

working mode. Self tune process begin when
the measured temperature is expected fall
below 90% of the set value the display shows

message alternately.Expected to fall

te.HI

below the temperature set point 60% evolved
and then self tune process starts automatically.

If asked to abort the self tune process,
parameter is done and key is
pressed.

NOTE:

If the output does not switch the relay and the C / A2 LED

does not light up though correct wiring and parameter

settings of the device:

Parameter on change over with the "F" key

from temperature indicator to temperature controller, then

change parameters back to “ ".

or

Reset the device to factory settings.

no

FtEC dSP.o

DEFAULT PARAMETERS

C.s.lO.
C.s.Hi.
C. PB
C.HyS
C. ti
C. td
C. Ct.
C.P.St.
C.EP.S.
S.s.t.S.
C.typ.

Control output
parameters

Pt100 input

TC input

0

600

0
2

4.0

1.00
20

0
0
0

HEat

-200

Set parameters

C1.sE.

400

C2.SE.

400

A2.SE.

500

F

A2.s.l
A2.s.H
A2Hy.
A2.tp
a2.st.
a2.Er.

Alarm2 output
parameters

TC input

0

600

indE

Hi
on

Pt100 input

-200

2

inp.t.
Unit
Fltr.
C.o.SE.
offs.
f.k.E.C.
m.sEt.

Configuration
parameters

Pt100 input

TC input

FE.cn.

°C

25

C-A2

0

nonE

50

Pt.

a2.Er.

Self tune
parameters

TC input

Pt100 input

no

Co.sc.
A2.Sc.
Cn.Sc.
S.t.Sc.
dEf.P.

Security

When holding key, the value of parameter flashes and using

parameters

keys the requested value can be adjusted.

Pt100 input

TC input

P.yEs
P.yEs
P.yEs
P.yEs

no

If key is pressed and held 0.6 seconds, the value of the selected
parameter changes rapidly. If waited enough,the value increases 100 at each

step. After 1 second following the release of the key, initial condition is
returned.The same procedure is valid for the decrement key.

SET

SET

SEcu.

S.Cod =.Security menu access

S.Cod.

yes

no

a.2.sc.

stco

Cn.sc.

St.Co

S.t.sc.

.

nonE

Modification Of Parameter Diagram

SET

SET

code
It should be 2011.

Cosc. CoN.o.

Co.sc.

menu security access level code.

nonE
P.yEs
P. no
a.2.sc. al2.o.

menu security access level code.

nonE
P.yEs
P. no

Co.sc. Conf.

menu security access level code.

nonE
P.yEs
P. no

S.t.Sc. S.tun.

men

u security access level code.

nonE
P.yEs

Co.sc. Conf.

dEF.P.

m

enu security access level code.

no

=

Parameter settings are not

change.

yEs

=

restored.

SET SET

=

Parameters of

=

Invisible.

=

Modification can be done.

= Only visible.

=

Parameters of

=

Invisible.

=

Modification can be done.

= Only visible.

=

Parameters of

=

Invisible.

=

Modification can be done.

= Only visible.

=

Parameters of

=

Invisible.

=

Modification can be done.

=

Parameters of

Parameter setting will be

SET

2. / 4

ET -E-050620192011