Enda ET2011-RT-230, ET2011, ET2011-T-230, ET2011-RT-110, ET2011-T-110 User manual

...

Read this document carefully before using this device. The guarantee will be expired by damaging of the device if you don't attend to the directions in the user manual. Also we don't accept any compensations for personal injury, material damage or capital disadvantages.

ENDA ET2011 PID TEMPERATURE CONTROLLER

Thank you for choosing 2011 temperature controller.ENDA ET

* x mm .77 35 sized * Selectable dual-set value.

* Se tlectable thermocouple ypes or Pt100 input.(Selection must be specified in order). * (SELF TUNE).Automatic calculation of PID parameters.

Enter PID parameters of the system if they are known at the beginning. Otherwise, Self-Tune should be activated.

* Soft-Start feature. * Input offset feature. * C/A2 Relay output can be programmable as alarm or control output.

* .Selectable SSR control output * Selectable heating/cooling control.

* In the case of sensor failure periodical running or relay state can be selected.

TECHNICAL SPECIFICATIONS

°F

ENDA

C/A2

SSR

°C

SET

english

ET2011

Input type

Pt 100 Resistance thermometer Pt 100 Resistance thermometer J (Fe-CuNi) Thermocouple K (NiCr-Ni) Thermocouple T (Cu-CuNi) Thermocouple S (Pt 0Rh-Pt) T1 hermocouple R (Pt13Rh-Pt) Thermocouple

EN 60584 EN 60584 EN 60584 EN 60584 EN 60584

EN 60751 EN 60751 -200...600 °C

- ... 00 °C99.9 3 .0

0...1700

Temperature range

°C

0... 600

°C

0...1300

°C

0... 400

°C

0...1700

°C °C

+32... +3092

ENVIRONMENTAL CONDITIONS

Ambient/storage temperature

Max. Relative humidity

Rated pollution degree

Height

Do not use the device in locations subject to corrosive and flammable gases.

0 ... +50 /°C -25... +70°C (with no icing) 80 up to 31 decreasing linearly 50 at 40.% %

According to EN 60529 Front panel : IP65 Rear panel : IP20

Max. 2000m

°C

ELECTRICAL CHARACTERISTICS

Supply Power consumption

Wiring Line resistance Data retention EMC

Safety requirements

230V AC +%10 -%20, 50/60Hz 24V AC %10, 50/60Hzor

Max. 5VA Power : , Si : 1 ²connector 2.5mm²' screw-terminal gnal connector ,5mm screw-terminal conenction. Max. 100ohm

EEPROM ( )minimum 10 years EN 61326-1: 2006 EN 61010-1: 2010 (Pollution degree 2, overvoltage category II)

OUTPUTS

C/A2 output

SSR output Life expectancy for relay

R : 250V AC, 8A (for resistive load), Selectable as NO+NC Control or Alarm2 output.elay R : 250V AC, 16A (for resistive load), Selectable as NO Control or Alarm2 output.elay

Max 20mA 12Volt (as control output) Withot load 30.000.000 mechanical operation; 250V AC, on the 8A resistive load 100.000 electrical switching

CONTROL

Control type Control algorithm

A/D converter Sampling time Proportional band

Control period Hysteresis Output power

Single set-point and alarm control

1 bit2 00ms1

Adjustable between 0 and 100 . If Pb=0 , On-Off control is selected.% % %

and 250 secondsAdjustable between 1 1 and 50Adjustable between °C/F

The ratio of power at a set point can be adjusted between 0 and 100% %

HOUSING

Housing type Dimensions Weight Enclosure material

While cleaning the device, solvents (thinner, benzine, acid etc.) or must not be used.corrosive materials

Suitable for flush-panel mounting according to DIN 43 700. W77xH35xD71mm

Approx. 200g (after packing) Self extinguishing plastics.

°F

- ...543 °F99.9 .0

-328...1112 °F +32... +1112

+32... +2 237 +32... +752 +32... +3092

Accuracy

0,5% (of full scale)

0,5% (of full scale) 1 digit °F °F °F °F °F

0, % ( )5 of full scale

0, % ( )5 of full scale 1 digit

1 digit

1 digit 1 digit

SURAN Industrieelektronik

Dettinger Str. 9 / D-72160 Horb a.N

Tel.: +49 (0)7451 / 625 617 Fax: +49 (0)7451 / 625 0650

E-mail : info@suran-elektronik.de Internet : www.suran-elektronik.de

ET2011-E-06052019

1. / 4

SET

If key is pressed while holding key, the programming mode is enabled.

SET

Con.o.

C.s.Lo.

C.s.Hi.

C. pb

C.Hys

C. ti

C. td

C. Ct.

C.p.st

C.E.p.s.

s.s.t.s.

C.typ

C.s.lo.= Control set point lower limit.(for

selected output)

Adjustable between 0 and C.s.Hi.

C.s.Hi.= Control setpoint upper limit.(for selected output)

Adjustable between and Upper scale

value.

C. Pb

= output) Adjustable between .0 and .0.

C. Pb

= %0 On-Off

C.Hys

= Hysteresis of the output.(for selected output) Adjustable between 1 and 50 °C.

C. Pb

= 0,this parameter is active.

C. ti

==Integral time.(for selected output) Adjustable between 0 and 100.0 minutes.

C. ti

C. Pb

parameter is different from “0”,this parameter appears.

C. td

==Derivative time.(for selected output) Asjustable between 0.00 and 25.00 minutes.

C. td

C. Pb

parameter is different from”0”,this parameter appears.

C. Ct.

= Period time.(for selected output) Adjustable between 1 and 250 second.

C. Pb

parameter is different is different from“0”,this parameter appears.

C.p.st = The ratio of output power at the setpoint.Adjustable between %0 and %100.

C.E.P.s. = The percentage of faulty sensor selected output power.Adjustable between %0 and %100.

Sst.S =Sofy starter timer set value

This parameter indicates the time to reach set point value when the device is first enegised. Adjustable between 0 and 250 minutes. If 0 is selected, soft start feature will be enable and the device reaches set point value quickly.

C.typ. = Control output type C.typ. HEAt

C.typ. CooL

While the parameter names appear,if and keys are pressed together, returns to the program mode.

C.s.Lo.

Proportional band.(for selected

%0 %100

.0, control is selected.

0.0,integral impact is disable.

0.0, derivative time is disable.

Pb = 0, so start feature will be disable. Setting ft

means heatign control.

means cooling control.

Entering from the programming mode to the run mode: If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered.

AL2.o.

A2.S.L

A2.S.H

A2.HY

A2.tP

A2.St.

A2.Er.

this parameter is seen and adjustable only

if set co.SE SSR =

a2.s.l= Alarm2set value lower limit. Adjustable between 0and A2.S.H

parameter value.

a2.s.H= Alarm2set value upper limit. Adjustable between

parameter value and upper scale value.

a2.Hy=.Hysteresis of the Alarm2 output Adjustable between 1 and 50 °C.

A2.tp

= Function of Alarm type. Four kinds of functions can be selected.

indE.

= alarm

Independdnt

(Independent)

dE.

= Deviation

bAnd

= Band alarm (Band)

bAn.i

= Band with inhibition

A2.st.Hi= The state of Alarm2 output.

If A2 output is above the set

= value. (on) lo=If A2 output is above the set value.(off)

A2.Er.on=

State of Alarm2 output in the

case of sensor failure.

2 output is probe failure (on).

= A

off= A2output is probe faiure (off).

A2.S.L

Alternatively, the same function occurs first pressing key and key is pressing programming mode is entered.Then and keys are pressing together,data is recorded and running mode is entered.

Programming mode

SET

ConF.

inp.t.

Unit

fltr.

C.o.sE

offs.

F.k.E.C.

m.SEt.

Input type selection.

FE.cn. nc.nA. c.cn.

= J type , = K type = T

p10.r. P13.r.

type =S type , = R type thermocouple selection. This parameter varies when changing some parameters.

Unit = The temperature unit. °C °F= °C, = °F

(This parameter varies when changing some parameters.)

fLtr.= Coefficient of digital filter. Filter for display value. Adjustable between 1 and . If this parameter is 1, digital filter runs most quick. If the parameter is , the filter run most slow. The value of parameter should be increased in interference.

C.o.sE = Control output selection

C-A2

= C/A2 (Relay) output selection

SSR

= SSR output selection

oFfS. = Offset value. Offset value is added to the measurement value. Adjusted between -100 and +100°C.The normal value is 0.

F.kE.C. = Function key setting parameter nonE

= Function key is off.

C2.S.A.

= The function key with 2.set value is used.

manu.

= Manual mode can be achieved with the function key.

dSP.o

= Device only the temperature display mode is entered

with function key.

m.SEt.

The percentage of manual output parameter. Adjustable between %0 and %100. This parameter allows manual adjustment of the output power when the manual output selection.

C. Pb.

200

, this parameter is not seen.

SET

S.tun.

St.Cu = Self tune control parameter.

s.t.Co.

200

SET

If both keys are pressed , message is displayed on the screen and self tune process is started automatically.

SET

If both keys are pressed, message is displayed on the screen and self tune process is stopped.

Selt tune begins when the measurement, and measurement value

PIdt.

message are shown alternately.Self tune process completed automatically after the parameter is done no and is entered to the

working mode. Self tune process begin when the measured temperature is expected fall below 90% of the set value the display shows

message alternately.Expected to fall

te.HI

below the temperature set point 60% evolved and then self tune process starts automatically.

If asked to abort the self tune process, parameter is done and key is pressed.

NOTE:

If the output does not switch the relay and the C / A2 LED

does not light up though correct wiring and parameter

settings of the device:

Parameter on change over with the "F" key

from temperature indicator to temperature controller, then

change parameters back to “ ".

Reset the device to factory settings.

FtEC dSP.o

DEFAULT PARAMETERS

C.s.lO. C.s.Hi. C. PB C.HyS C. ti C. td C. Ct. C.P.St. C.EP.S. S.s.t.S. C.typ.

Control output parameters

Pt100 input

TC input

600

0 2

4.0

1.00 20

0 0 0

HEat

-200

Set parameters

C1.sE.

400

C2.SE.

400

A2.SE.

500

A2.s.l A2.s.H A2Hy. A2.tp a2.st. a2.Er.

Alarm2 output parameters

TC input

600

indE

Hi on

Pt100 input

-200

inp.t. Unit Fltr. C.o.SE. offs. f.k.E.C. m.sEt.

Configuration parameters

Pt100 input

TC input

FE.cn.

°C

C-A2

nonE

Pt.

a2.Er.

Self tune parameters

TC input

Pt100 input

Co.sc. A2.Sc. Cn.Sc. S.t.Sc. dEf.P.

Security

When holding key, the value of parameter flashes and using

parameters

keys the requested value can be adjusted.

Pt100 input

TC input

P.yEs P.yEs P.yEs P.yEs

If key is pressed and held 0.6 seconds, the value of the selected parameter changes rapidly. If waited enough,the value increases 100 at each

step. After 1 second following the release of the key, initial condition is returned.The same procedure is valid for the decrement key.

SET

SEcu.

S.Cod =.Security menu access

S.Cod.

yes

a.2.sc.

stco

Cn.sc.

St.Co

S.t.sc.

nonE

Modification Of Parameter Diagram

SET

code It should be 2011.

Cosc. CoN.o.

Co.sc.

menu security access level code.

nonE P.yEs P. no a.2.sc. al2.o.

menu security access level code.

nonE P.yEs P. no

Co.sc. Conf.

menu security access level code.

nonE P.yEs P. no

S.t.Sc. S.tun.

men

u security access level code.

nonE P.yEs

Co.sc. Conf.

dEF.P.

enu security access level code.

Parameter settings are not

change.

yEs

restored.

SET SET

Parameters of

Invisible.

Modification can be done.

= Only visible.

Parameters of

Invisible.

Modification can be done.

= Only visible.

Parameters of

Invisible.

Modification can be done.

= Only visible.

Parameters of

Invisible.

Modification can be done.

Parameters of

Parameter setting will be

SET

2. / 4

ET -E-050620192011

TERMS

( )5

C/A2

°F

SSR

ENDA

( 1 ) PV and SV display

Character heights ( ),( ),( )2 3 4 Keypad ( )5 State indicator

7 4 LED display segment, digits red

mm12

Mikro switch , Alarm1 SSRFor control and outputs 3 digits red LED

ALARM2 OUTPUT TYPES

Independent Alarm

A2.tp. indE=

OFF

Deviation Alarm

A2.tp dE.

°C

SET

ET2011

( 1 ) )

Measurement value and set value indicator Running mode

Paramet (Progra )

er name and value mming mode

( ) ( rogram )

2 Value increment key P ming mode

A2.St. H i=

OFF

If only this key is pressed in normal operation,software version

number is seen. parameter processing

( )

2 Value decrement and parameter selection key.

( rogram )

P ming mode

( ) ( )

4 Control ve Alarm set selection key Running mode

Paramet (Program )

er set key ming mode

(F.k.E.C. )

Band

Alarm

A2.tp. bAnd

OFF

A2.St. l o=

OFF

a2,Hy

(ASV min. = ASV ma = )

SV = ASV =Set point of CONT output Set point of alarm output

ASV

beginning of scale

x. end of scale

SV+ASV

SV-ASV

OFF

Beginning

SV = ASV = (ASV min. = 0, ASV maks. = 300 )Set point of CONT output Set point of AL2 output

-300 (ASV min. =-300, ASV ma . = +300)x

Band alarm is possible

MODIFICATION OF CONTROL AND ALARM SET POINTS

250

3 seconds later

SET

C1.SE.

399

OFF

=A1.St. L o

A2.Hy

SV+ASV

+300

300

SV = ASV =Set point of CONT output Set point of AL2 output

Band Alarm With Inhibition

A2.tp. bAn.i

SV+ASV

SV-ASV

OFF

Beginning

400

3 seconds later

A2.Hy

SV-ASV

Band alarm is possible

SV+ASV

(ASV min. = 0, ASV ma = +300)X.

OFF

A2.Hy

ERROR MESSAGES

pfa

----

____

psC

=A2.St. H i

300

Sensor is broken

Temperature value is higher than the value

Temperature value is lower than the scale

Pt100 sensor is short circuit

C2.SE.

SET

a2.SE.

399

499

SURAN Industrieelektronik

Dettinger Str. 9 / D-72160 Horb a.N

398

500

3 seconds later

Tel.: +49 (0)7451 / 625 617 Fax: +49 (0)7451 / 625 0650

parameter, is set to the parameter,this

F.kE.C. C2.S.A.

parameter is displayed.

C.O.SE.parameter is set to the output of SSR,this parameter is seen.

E-mail : info@suran-elektronik.de Internet : www.suran-elektronik.de

ET2011-E-06052019

3. / 4

8680407711246

DIMENSIONS

8 680407 7 1 1246

8 680407 7 1 1284

8 680407 7 1 1321

8 680407 7 1 1369

C/A2

°F

77mm

SSR

°C

SET

Depth

73mm 5mm

For removing the device from the panel:

- While pressing both side of

the device in direction , push it1 in direction 2.

ENDA

789

MADE IN TURKEY

SN: XXXXXXXXX

Order Code 2011-X XXX- X: ET -

CONNECTION DIAGRAM

ENDA ET2011 is intended for installation in control panels. Make sure that the device is used only for intended purpose. The shielding must be grounded on the instrument side. During an installation, all of the cables that are connected to the device must be free of energy. The device must be protected against inadmissible humidity, vibrations, severe soiling.Make sure that the operation temperature is not exceeded. All input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. These cables should not be close to the power cables or components. The installation and electrical connections must be carried on by a qualified staff and must be according to the relevant locally applicable regulations.

ET2011

1 2 3 4 5 6

RESISTIVE LOAD 250V AC 8A C/A2

PID DIGITAL THERMOSTAT ET20 1-T-230

ENDAINDUSTRIAL ELECTRONICS

Input selection

RT....PT100 input

....

T TC input

Flush

mounting

Connection cable

Panel cut-out

71mm

clamp

Note

1) Panel thickness should be maximum 7mm.

2) If there is no 60mm free space at back side of the device, it would be difficult to remove it from the panel.

Supply voltage

230 ... 230V AC

VAC ...

110VAC......110V AC

24 ........24V AC

0 VAC

SM.......9-30VDC/7-24V AC

Contact current selection

None......8A contact output

....

P 16A contact output

Flush mounting clamp

Panel

ENDAINDUSTRIAL ELECTRONICS

ET20 1-T-230

PID DIGITAL THERMOSTAT

C/A2 250V AC 8A RESISTIVE LOAD

11223344556

ENDAINDUSTRIAL ELECTRONICS

ET20 1-T-230-P

PID DIGITAL THERMOSTAT

C/A2 250V AC 16A RESISTIVE LOAD

NOTE :

SUPPLY:

Phase

184-253V AC 50/60Hz 5VA

Neutral

77889

Holding screw

0.4-0.5Nm

F 100 mA

250V AC

Fuse should be connected.

Fuse

SN: XXXXXXXXX

Switch

Cable size: 1,5mm²

ENDAINDUSTRIAL ELECTRONICS

ET20 1-RT-230

PID DIGITAL THERMOSTAT

C/A2 250V AC 8A RESISTIVE LOAD

1 2 3 4 5 6

ENDAINDUSTRIAL ELECTRONICS

ET20 1-RT-230-P

PID DIGITAL THERMOSTAT

C/A2 250V AC 16A RESISTIVE LOAD

7 8 9

1 2 3 4 5 6

Equipment is protected throughout by DOUBLE INSULATION.

Note

1) Mains supply cords shall meet the requirements of IEC 60227 or IEC 60245.

230V AC Supply

2) In accordance with the safety regulations, the power supply switch shall bring the identification of the relevant instrument and it should be easily accessible by the operator.

7 8 9

SN: XXXXXXXXX

PT100

SURAN Industrieelektronik

Dettinger Str. 9 / D-72160 Horb a.N

Tel.: +49 (0)7451 / 625 617 Fax: +49 (0)7451 / 625 0650

E-mail : info@suran-elektronik.de Internet : www.suran-elektronik.de

ET2011-E-06052019

4. / 4

Enda ET2011-RT-230, ET2011, ET2011-T-230, ET2011-RT-110, ET2011-T-110 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual