TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
Precautions
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
:
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Laser Safety
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible
eye injury.
CAUTION:USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECI-
CAUTION:VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO
LOCATION:INSIDE, NEAR THE DECK MECHANISM.
FIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
BEAM.
FCC WARNING-This equipment may generate or use radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this equipment if an unauthorized change or modification
is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your
local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning
chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
For Customer Use:
Read carefully the information located at the bottom of this unit and enter below the Serial No. Retain this information for
future reference.
Model No.
Serial No. _____________________
_____________________
–2–
EN
IMPORTANT SAFEGUARDS
1) Read Instructions - All the safety and operating instructions should be read before the product is operated.
2) Retain Instructions - The safety and operating instructions should be retained for future reference.
3) Heed Warnings - All warnings on the product and in
the operating instructions should be adhered to.
4) Follow Instructions - All operating and use instructions
should be followed.
5) Cleaning - Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not recommended by the product manufacturer as they may
cause hazards.
7) Water and Moisture - Do not use this product near
water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or near
a swimming pool; and the like.
8) Accessories - Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the
product should follow the manufacturer’s instructions, and should use a
mounting accessory recommended
by the manufacturer.
9) A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to
overturn.
10) Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of
the product and to protect it from overheating, and
these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions have been
adhered to.
11) Power Sources - This product should be operated only
from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local
power company. For products intended to operate from
battery power, or other sources, refer to the operating
instructions.
12) Grounding or Polarization - This product may be
equipped with a polarized alternating-current line plug
(a plug having one blade wider than the other). This
plug will fit into the power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
13) Power-Cord Protection - Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
product.
14) Lightning - For added protection for this product during
a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet. This will prevent damage to the product due to
lightning and power-line surges.
15) Power lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.
16) Overloading - Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17) Object and Liquid Entry - Never push objects of any
kind into this product through openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid
of any kind on the product.
18) Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
19) Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into
the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by follow-
ing the operating instructions. Adjust only those con-
trols that are covered by the operating instructions
as an improper adjustment of other controls may
result in damage and will often require extensive
work by a qualified technician to restore the product
to its normal operation,
e) If the product has been dropped or damaged in any
way.
f ) When the product exhibits a distinct change in per-
formance - this indicates a need for service.
20) Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21) Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
22) Heat - The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
The following symbols appear in some headings in this manual.
: Description refers to playback of DVD-Video discs.
Precautions
•
Owner’s Manual
(1VMN20420)
• Foot
(1VM421328)
Installation Location
For safety and optimum performance of this unit:
• Do not place anything directly on top of the unit. Do
not place the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid
places. Avoid places with insufficient ventilation for
proper heat dissipation. Avoid locations subject to
strong vibration or strong magnetic fields.
• Be sure to remove the disc and unplug the AC
power cord from the output before carrying the unit.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Moisture Condensation Warning
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. Do not use this unit at least for 2 hours
until its inside gets dry.
About Copyright
Unauthorized copying, broadcasting, public performance
and lending of discs are prohibited.
This product incorporates copyright protection technology
that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
Stand
•
(1VM220356)
: Description refers to playback of Audio CDs.
: Description refers to playback of MP3 files.
: Description refers to playback of discs formated
with WMA.
Maintenance
SERVICING
¡Please refer to relevant topics on the “Troubleshooting
Guide” on page 17 before returning the product.
¡If this unit becomes inoperative, do not try to correct
the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power plug,
and please call our help line mentioned on the front
page to locate an Authorized Service Center.
CLEANING THE CABINET
¡Use a soft cloth slightly moistened with a mild deter-
gent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive.
CLEANING DISCS
¡When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe
in a circular motion.
¡Do not use solvents such as benzine, thinner, com-
mercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for analog records.
CLEANING THE DISC LENS
¡
If this unit still does not perform properly although you refer
to the relevant sections and to “Troubleshooting Guide” in
this Owner’s Manual, the laser optical pickup unit may be
dirty. Consult your dealer or an Authorized Service Center
for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
¡When you handle a disc hold it by its edge and try not
to touch the surface of the disc.
¡Always store a disc in its protective case when it is
not used.
¡
If the disc’s peripheral edge is rough, rub it with pen or
pencil stem in order to fine the rough completely. If not,
the disc may not be inserted correctly, or the plastic fragments may stick on the disc and cause skips of playback.
“WMA” (Windows Media Audio) is a new audio codec developed by Microsoft®in the United States of
America.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
–4–
EN
DVD-Video
* 1, 2, 4, 6
* 1, 3, 4,
5, 6, 8
* 1, 3, 4, 5,
6, 7, 9, 10
* 4, 6
* 4, 5, 6,
9, 10
or
DVD-RW
DVD-R
DVD+RW
DVD+R
Audio CD
CD-RW
CD-R
Digital video
(MPEG2)
-
-
-
Region code
Mark (logo)
Playable
discs
Recorded
signals
Disc size
Disc types
12 cm
Example
Title 1Title 2
Chapter 1 Chapter 2Chapter 1
Chapter 2
Chapter 3 Chapter 4
Digital audio
or
MP3/WMA
12 cm
Example
Group 1Group 2
Track 1
Track 2Track 5
Track 6
Track 3
Track 4
Example
Track 1
Track 2
Track 5
Track 6
Track 3
Track 4
Audio CD
MP3/WMA
Digital audio
-
About the Discs
is a trademark of DVD Format/Logo Licensing Corporation.
Playable Discs
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot
be played back.
Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.
*2:
*3: Discs recorded in the VR (Video Recording) format cannot be played back.
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the
recorder or special properties of discs.
*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not
play them back. Even if they are played back, the sound or video quality will be compromised.
*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD
recorder. However, depending on the recording status of a disc, the disc may not be played back at all or
normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with the
DVD recorder. Refer to the manual accompanying the DVD recorder.
*8: Only the discs recorded in the video format and finalized can be played back.
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be
played back at all or normally (the picture or sound may not be smooth, etc.).
If there is too much recording space left on a disc (the used portion is less than 55 mm across), it may not play
*9:
back properly.
*10: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it
correctly.
Precautions
•Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in
the United States and/or other countries.
• This unit is not compatible with Multiple Bit Rate (MBP: a file that contains the same content encoded at several different
bit rates).
Unplayable Discs
¡
NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM/CD-I/Photo CD/Video CD / DVD with region codes other than 1 or ALL
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers
• Never insert a disc which is broken or whose form is abnormal (other than 12 cm round disc).
¡
On the following disc, the sound MAY NOT be heard.
Super Audio CD
NOTE: Only the sound recorded on the normal CD layer can be delivered.
¡
Any other discs without compatibility indications.
The sound recorded on the high density Super Audio CD layer cannot be delivered.
–5–
EN
Setup
S-VIDEO
OUT
VIDEO
OUT
AUDIO OUT
DIGITAL
AUDIO OUT
COAXIAL
L
R
AUDIO OUT
L
R
LR
AUDIO IN
VIDEO IN
VIDEO
OUT
S-VIDEO IN
S-VIDEO
OUT
Connections
If your TV has AUDIO/VIDEO input jacks, see the following instructions.
Connection to a TV
Method 1
Good pictureBasic Audio
Method 2
Better picture
TV
(INPUT)
S-Video
cable
(commercially
available)
Setup
This unit
Audio cable
(supplied)
Video
cable
(supplied)
or
(OUTPUT)
(Analog)
VIDEO OUT
S-VIDEO OUT
Hint
Hint
AUDIO OUT
• Connect this unit directly to the TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted
due to the copy protection system.
RF Modulator Connection
If your TV has Antenna in jack only, it is still possible to
connect this unit to your TV by using a STEREO
AUDIO/VIDEO RF Modulator (commercially available).
In this case, follow the instructions below.
1) Connect the AUDIO/VIDEO output jacks of this unit to the
AUDIO/VIDEO input jacks of your RF Modulator by audio
and video cables.
2) The antenna input jack of your TV may have been already
occupied. If so, disconnect the RF cable from your TV, and
then connect the RF cable to your RF Modulator (usually
marked “ANT IN”).
3)
Connect your RF modulator to your TV by another RF cable.
4) Set your RF modulator’s channel 3/4 switch to either 3 or
4, whichever the TV channel is least used in your area. If
your RF modulator has a Modulator/Antenna switch, set it
according to your RF modulator’s manual.
5) Turn on your TV and choose the same channel as you set
the RF modulator’s channel 3/4 switch to.For more details,
follow the instructions supplied with the RF Modulator.
Antenna
Cable
Signal
Stereo Audio/Video RF Modulator
(commercially available)
ANT IN
AC 120V
TO TVCHANNELVIDEO AUDIO
RL34
2
3
Hint
Hint
• The quality of picture may become poor if the unit is con-
nected to an RF Modulator.
(Back of this unit)
1
Audio/Video
Cables
(Supplied)
RF Cable (Not supplied)
COAXIAL
AUDIO OUT
DIGITAL
AUDIO OUT
R
L
VIDEO
OUT
S-VIDEO
OUT
(Back of TV)
Antenna in jack
After you have completed connections
•
Hit the input selector button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input channel (usually
near channel 0) for viewing the picture from this unit. If the picture does not appear, also refer to the manual accompanying your TV.
INPUT MODES FOR COMMON TV BRANDS (Example)
• Listed below are inputs for common brand name TV’s.
Admiral:AUX
* To complete these settings, refer to pages 14-15.
Hint
Hint
•
Playing a DVD using incorrect settings may generate noise
distortion and may also damage the speakers.
SETUP > AUDIO menu >
DOLBY DIGITAL
PCM
Method 2
Dolby Digital decoder,
MD deck or DAT deck
Digital audio
input jack
Audio Coaxial
Digital cable
(commercially
available)
DIGITAL
AUDIO OUT
Connection
Setting
Connecting to a Dolby Digital decoder
for Dolby Digital audio output.
Connecting to the other equipment (an MD deck or
DAT deck etc.) without Dolby Digital decoder.
* To complete these settings, refer to pages 14-15.
Hint
Hint
•
The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD or
DAT deck.
•
By hooking this unit up to a Multi-channel Dolby Digital decoder,
you can enjoy high-quality Dolby Digital 5.1 channel surround
sound as heard in the movie theaters.
•
Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.
SETUP > AUDIO menu >
DOLBY DIGITAL
BITSTREAM
PCM
Setup
Rear Terminals
AUDIO OUT jacks
Connect the supplied audio cable
(red/white) here through the audio in
jacks of a TV or other audio equipment.
S-VIDEO OUT jack
Connect an optional S-Video cable here
through the S-video in jack of a TV.
R
VIDEO
OUT
OUT
COAXIAL
S-VIDEO
–7–
AUDIO OUT
DIGITAL
AUDIO OUT
L
DIGITAL AUDIO OUT COAXIAL jack
Connect an optional coaxial digital audio
cable here through the coaxial digital
audio in jack of a decoder or audio
receiver.
VIDEO OUT jack
Connect the supplied video cable (yellow) here through the TV’s video in jack.
EN
About the Remote Control
• To turn the unit on or off.• To turn the unit on or off.
• To display the current disc
mode.
• To display the current disc
mode.
• To select chapter or title
directly.
• To select track directly.
• To select camera angles on
a disc.
• To select subtitles on a disc.
• To select audio languages on
a disc.
• To select STEREO,
L-ch or R-ch. (CD)
• To repeat between your
chosen point A and B.
• To repeat between your
chosen point A and B. (CD)
• To play a chapter or title
repeatedly.
• To play a track or disc
repeatedly. (CD)
• To play a track, group or disc
repeatedly. (MP3/WMA)
• To return to the previous
operation in menu.
• To set black level on/off.
• To set virtual surround on/off.
• To arrange the playing
order or play randomly.
• To set virtual surround on/off.
• To call up the Menu
on a disc.
• To call up the Top Menu
on a disc.
• To magnify part of a picture.
(x2/x4)
• To return to the previous
operation in menu.
• To search chapter, title or time.
• To set or search the
markers.
• To search track.
• To search time. (CD)
• To set or search the
markers. (CD)
• To clear the markers.
• To cancel the point for A-B
repeat.
• To cancel the point for A-B
repeat. (CD)
• To clear the markers. (CD)
• To remove status number
in program input.
• To clear the numbers
entered incorrectly.
• To clear the numbers
entered incorrectly.
• To search forward/backward
through a disc.
• To begin slow forward
/reverse playback during
the pause mode.
• To search forward/backward
through a disc.
• To call up the file list.
(MP3/WMA)
• To advance playback
one frame at a time.
• To pause disc playback.
• To pause disc playback.
• To stop playback.• To stop playback.
•
To return to the top file of the
highest hievarcy in the program
and file list. (MP3/WMA)
• To skip chapters.• To skip tracks.
• To begin disc playback.• To begin disc playback.
• To call up the DVD setup
menu.
• To call up the DVD setup
menu.
• To move the cursor and
determine its position.
• To move the cursor and
determine its position.
POWER
DISPLAY
MENU
TOP MENU
ZOOM
SUBTITLE
MODE
ANGLE
SEARCH
MODE
REPEAT
A-B
AUDIO
CLEAR
123
456
789
0
+1 0
PAUSE
PLAY
STOP
SETUP
DVD-V
DVD-V
Button
(Alphabetical order)
Disc
ENTER
RETURN
REVFWD
SKIP
CD
CD
MP3
MP3
WMA
WMA
• Hit to remove the disc.• Hit to remove the disc.
EJECT
POWER
AUDIO
SUBTITLE
ANGLE
REPEAT
CLEAR
A-B
PAUSE
SETUP
TOP MENU
MENU
ENTER
MODE
ZOOMRETURN
SLOW
SKIP
EJECT
DISPLAY
SEARCH
MODE
123
456
789
0+10
PLAY
REVFWD
STOP
2
1
3
POWER
STOP
PLAY
EJECT
C
B
A
Remote Control
Setup
Installing the Batteries
for the Remote Control
Install two AA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote
control.
Keep in mind the following when using the
remote control:
•
Make sure that there is no
obstacle between the
remote control and the
remote sensor on the unit.
• The maximum operable
ranges from the unit are
as follows.
- Beeline: approx. 23
feet (7m)
-
Either side of the center:
- Above: approx. 16 feet
- Below: approx. 10 feet
approx. 16 feet (5m)
within 30°
(5m) within 15°
(3m) within 30°
–8–
EN
DVD-V
DVD-V
WMA
WMA
MP3
MP3
CDCDDVD-V
DVD-V
DVD-V
DVD-V
WMA
WMA
MP3
MP3
CDCDDVD-V
DVD-V
PLAY
Functions
STOP
POWER
E
1
1
WMA
WMA
MP3
MP3
CDCDDVD-V
DVD-V
WMA
WMA
MP3
MP3
CDCDDVD-V
DVD-V
Press 'PLAY' to play from here.
To play the beginning,
press 'STOP' first and then 'PLAY'.
Resume ON
DVD-V
DVD-V
x2x4
Operations described after this section are mainly based on the remote control use. Some operations can be carried out on main unit.
Playback
Before: Turn on the TV, amplifier and any
other equipments which are connected
to this unit. Make sure the TV and audio
receiver (commercially available) are set
to the correct channel.
(
1
1
⇒Page 10
2
2
)
Insert a disc with
label facing to the
left.
3
3
To start
playback
4
4
To stop
playback
1
1
3
3
4
4
Lights up when
power is on.
POWER
SEARCH
MODE
DISPLAY
AUDIO
123
SUBTITLE
456
ANGLE
789
REPEAT
CLEAR
0 +10
A-B
SKIP
PAUSE
SLOW
PLAY
REVFWD
STOP
SETUP
TOP MENU
ENTER
MODE
ZOOMRETURN
Hint
1
1
4
4
3
3
EJECT
2
2
MENU
POWER
EJECT
STOP
C
PLAY
B
A
Hint
• When you play an MP3/WMA file, details on
page 10.
• A “prohibited icon” may appear at
the top-right on the TV screen when
the operation is prohibited by the
disc or this unit.
• Some DVDs may start playback from title 2 or
3 due to specific programs.
• During the playback of a two-layered disc, pictures may stop for a moment. This happens
while the 1st layer is being switched to the
2nd layer. This is not a malfunction.
• Don't leave the disc exiting halfway from the
slot.
TIP:
You can change the On-Screen language in
“PLAYER MENU” setting. (Refer to page 14.)
DVD menu
Some discs contain menus which allow you to customize
DVD playback. Press [KK/ LL/ ss/ BB] to select an item, then
press [ENTER] (or [PLAY BB]), to select.
Calling Up a Menu Screen during Playback
• Hit [MENU] to call up the DVD menu.
• Hit [TOP MENU] to call up the title menu.
Hint
Hint
• Menu operations may vary depending on the disc. Refer to the
manual accompanying the disc for more details.
Resume
Hit [STOP CC]. Resume message will appear on the TV
screen.
Hit
[PLAY BB], playback will
resume from the point at which
playback was stopped.
<Example : DVD>
Hint
Hint
• To cancel resume, hit [STOP CC] one more time during the stop
mode.
• For MP3/WMA, playback will resume from the beginning of the
track at which playback was stopped.
•
The resume information will be kept even when the power is turned off.
Paused and Step-by-Step Playback
Fast Forward/Reverse Search
Press [FWD gg] or [REV hh] repeatedly during playback to select the required forward or
reverse speed.
To continue playback, hit [PLAY B].
Hint
Hint
•
For DVDs, fast forward or reverse search speed is different depending on
the disc. Approximate speed is 1(x2), 2(x8), 3(x20), 4(x50) and 5(x100).
• For Audio CDs, approximate speed is 1(x2), 2(x8) and 3(x30).
• For MP3/WMA, approximate speed is 1(x2), 2(x8) and 3(x30).
Slow Forward/Slow Reverse
Press [FWD gg] or [REV hh] repeatedly during the pause mode to select the required forward or reverse speed.
To continue playback, hit [PLAY B].
Hint
Hint
• Slow forward or reverse speed is different depending on the disc.
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).
• Set “STILL MODE” to “FIELD” in the Display menu if pictures in the
slow playback mode are blurred. (Refer to pages 14-15.)
Zoom
Hit [ZOOM] repeatedly during playback to select the
required zoom factor: x2, x4 or OFF.
Functions
Hit [PAUSE FF] during playback.
To continue playback, hit [PLAY B].
The disc goes forward by one frame each time [PAUSE FF]
is hit during the pause mode.
To continue playback, hit [PLAY B].
Hint
Hint
• On DVDs, set “STILL MODE” to “FIELD” in the Display menu if pic-
tures in the pause mode are blurred. (Refer to pages 14-15.)
Press [KK/ LL/ ss/ BB] to slide the zoomed picture across the
screen.
To exit zoom function, hit [ZOOM] repeatedly to select OFF.
Hint
Hint
• Zooming function does not work while the disc menu is showing up.
• x4 zoom is not available on some discs.
• The picture may be distorted when you press
[REV hh] repeatedly in the zoom mode.
• It may take several seconds to slide the zoomed picture.
[PAUSEkk] or
–9–
EN
DVD-V
DVD-VCDCD
4/12 0:03:21 - 0:02:15
T
4/12 0:13:45 - 0:45:40
T
11/16 0:00:00 - 0:03:30
1/3 0:00:00 - 1:23:45
TL1
DISPLAY
DISPLAY
DISPLAY
DISPLAY
DISPLAY
DISPLAY
DISPLAY
MP3/WMA Playback
WMA
WMA
MP3
MP3
MENU
PLAY
WMA
WMA
MP3
MP3
DISPLAY
DISPLAY
DISPLAY
DISPLAY
TRACK 01
1/36 0:01:15
T
PROGRAM
RANDOM
or
ARTIST NAME
TITLE NAME
DISPLAY
MP3/WMA is a method of compressing files. You can copy MP3/WMA files on CD-R/RWs from the computer and play the files on this unit.
2
2
Insert an MP3/WMA-format disc, then hit
[MENU] to call up the file list on the TV screen.
1
1
ENTERENTER
or
FILE LIST
DISC NAME
FOLDER
3
MP3
WMA
folder name 1
folder name 2
folder name 3
folder name 4
3
file name 1
3
file name 2
file name 3
ENTER
PLAY
folder name 1
When selecting the folder:
[BB]
• Hit
go to the next hierarchy.
• Hit
[ss] when you want
to go back to the previous hierarchy (except for
the top hierarchy).
1/ 2
when you want to
STOP
Refer to “Resume” on page 9.
Hint
Hint
• Some selections may take a while to be recognized.
[TOP MENU] to return to the first item.
• Hit
• Folders are known as Groups; files are known as Tracks.
• MP3 files are accompanied by icon.• WMA files are accompanied by icon.
• Folders are accompanied by icon.
• A maximum of 255 folders can be recognized.
• A maximum of 999 files can be recognized.
• Up to 8 hierarchies can be created.
This player recommends the files recorded under the following circumstances:
For MP3/WMA file recorded in Variable Bit Rate(VBR), the unit may not display the actual elapsed time.
•
• Copyright protected WMA files will not play on this unit.
3
On-Screen Display
You can check the information about the current disc by hitting [DISPLAY] on the remote control.
Functions
NOTE: For WMA files,and will be displayed
1-A
1-A
1-B
1-B
1
1
2
2
3
3
4
4
1
1
after .
Angle icon, appears only when available on the DVD
Current playback status
Remaining time of the current chapter
Elapsed time of the current chapter
CH(Chapter):
Current chapter number / Total chapters
Remaining time of the current title
Elapsed time of the current title
TT(Title):
Current title number / Total titles
Layer numbers, appears only when
playing a two-layered Disc
L0: Layer 0 is playing
L1: Layer 1 is playing
Current repeat setting appears only
when the repeat setting is active
C: Chapter repeat / T: Title repeat /
A B: A-B repeat
BIT RATE: The amount of audio and
video data currently being read
1-A
1-A
1-B
1-B
Title name based on tag information currently in play will be
displayed.
Artist name based on tag information currently in play will be
displayed.
Current playback status
1
1
Remaining time of the current track
Elapsed time of the current track
TR(Track):
Current track number / Total tracks
ALL:
2
2
Current track number / Total tracks
Current repeat setting appears only
when the repeat setting is active
T: Track repeat
A: All Tracks repeat
A B: A-B repeat
Remaining time of the entire disc
Elapsed time of the entire disc
3
3
Hint
Hint
• When you are playing a disc in PROGRAM or RANDOM mode,
PROGRAM (or RANDOM) will be displayed instead of .
Current playback status
1
1
The name of the file currently
in play will be displayed.
TR(Track):
2
2
Current track number / Total tracks
Current repeat setting, if active
T: Track repeat
G: Group (folder) repeat
A: Disc repeat
Elapsed playing time of the current
track
3
3
(Only when you are playing a disc in PROGRAM or RANDOM mode.)
4
4
–10–
2
2
EN
Search Function
CDCDDVD-V
DVD-V
1:29:00
TOTAL
1:29:00
TOTAL
SEARCH
MODE
PLAY
CDCDDVD-V
DVD-V
SEARCH
MODE
PLAY
WMA
WMA
MP3
MP3CDCD
/29
/29
DVD-V
DVD-V
/12
/12
123
456
789
0
+1 0
SEARCH
MODE
SEARCH
MODE
TR 1 TR 2 TR 3 TR 4
Current Track
(TR)
SKIPSKIP
SKIP
SKIP
CH 1 CH 2 CH 3 CH 4
Current Chapter
(CH)
or
SKIP
TT 1 TT2 TT3 TT4
Current Title
(TT)
SKIP
SKIP
SKIP
Track Search
Using [SEARCH
Using [SEARCH
1
1
2
2
Within 30 seconds.
• For the disc with less than 10 tracks,
hit the track number directly.
•
For discs with more than 10 but less
than 99 tracks, to play single-digit track,
hit [0] first, then the track number (e.g.
for track 3, hit [0], [3]). To play a double-digit track, hit the track number.
• For discs with more than 100 tracks, to
play a single or a double-digit track, hit
[0] first, then the track number (e.g. for
track 3, hit [0], [0], [3], and for track
26, hit [0], [2], [6]). To play a triple-digit
track, hit the track number.
Using [SKIP
Using [SKIP
1
1
PLAY
Hint
Hint
•
[+10] button can also bring the Track Search
display, except for the disc with less than 10
tracks. For such a disc, track search can be
done by just hitting the track number.
HH
HH
MODE]
MODE]
GG
,
]
GG
,
]
Title / Chapter Search
Using [SEARCH
Using [SEARCH
1
1
Hit once for the chapter search.
Hit twice for the title search.
2
123
2
456
789
0
+1 0
Within 30 seconds.
Using [SKIP
Using [SKIP
1
1
PLAY
(If the disc has no chapters)
Hint
Hint
• Depending on the disc being played, this
function can also be performed by directly
entering the desired chapter number with
the Number buttons. Refer to the manual
accompanying the disc.
• For CDs and MP3/WMA, Track Search is
not available for Programmed or Random
Playback.
HH
HH
MODE]
MODE]
GG
,
]
GG
,
Time Search
1
1
Hit repeatedly until the
Time Search display
appears.
123
2
2
456
789
0
Within 30 seconds.
]
Hint
Hint
• When there is no need to enter a number,
“0” appears automatically.
For example, “0 : 0-:--” appears in the
Time Search display if the total time of the
title or track is less than 10 minutes.
[CLEAR] to erase the incorrect input at
• Hit
step 2).
Functions
Marker Setup
This feature allows you to assign a specific
point on a disc to be called back later.
o set a marker
TTo set a marker
1
1
PLAY
SEARCH
MODE
2
2
or
3
3
ENTERENTER
Hit repeatedly until the
marker display
appears.
o return to the marker
TTo return to the marker
later
later
1
1
Hit repeatedly until
the marker display
appears.
2
2
or
3
3
ENTERENTER
at the desired marker
•Playback will restart from the specific point
which you set.
–11–
o e
xit the marker displayy
TTo e
xit the marker displa
1
1
Hint
Hint
• The Marker display will disappear in about
30 seconds when there is no output.
• To clear a marker, select the marker to be
cleared at step 2) in the section “To set a
marker” or “To return to the marker later”
and then hit
• Removing the disc or turning off the power
will erase all markers.
• Selecting “AC” at step 2) in the section “To
set a marker” or “To return to the marker
later” will also erase all markers.
Repeat function is available only during
playback.
1
1
Each time you hit [REPEAT], repeat
function changes as example below.
Functions
Hint
Hint
• Repeat setting will be cleared when moving to another title, chapter, track or group.
• Repeat playback may not function with
some discs or during repeat A-B playback.
PLAY
REPEAT
CHAPTER
TITLE
OFF
TRACK
ALL
OFF
TRACK
GROUP
ALL
OFF
(current chapter repeat)
(current title repeat)
(repeat off)
(current track repeat)
(
entire disc repeat)
(repeat off)
(current track repeat)
(current group repeat)
(
entire disc repeat)
(repeat off)
1
1
PLAY
A-B
at your desired starting point (A)
2
2
A-B
A-B
at your desired end point (B)
• Point B should be in the same title or
track as point A.
Hint
Hint
• To exit the sequence, hit [A-B] so that
OFF appears.
• To cancel Point A, hit
• This function does not work in the other
repeat modes.
[CLEAR].
Random Playback
This function shuffles the playing
order of tracks instead of playback
in the sequence.
1
1
STOP
Hit twice
2
2
PLAY
Hint
Hint
• To repeat the current track in the random
selections, hit
“TRACK” appears during playback.
• To repeat the entire random selections, hit
[REPEAT] repeatedly until “ALL”
appears during playback.
RANDOM
CD-DA TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
PLAY
<Example : CD>
.
[REPEAT] repeatedly until
–12–
You may determine the order in which
tracks will play.
1
1
STOP
MODE
Hit once.
2
2
or
ENTERENTER
3
3
PLAY
Hint
Hint
• Hit [CLEAR] at step 2) to erase the most
recently entered track.
• To erase all programmed tracks at once,
select “ALL CLEAR’’ and hit
step 2).
• While a program is being played back,
[STOP CC] works as follows;
⇒
Hit [STOPCC] and [PLAY BB] next, so
that the programmed playback restarts.
(CD playback restarts from the current
point. MP3/WMA playback restarts from
the beginning of the current track.)
⇒
Hit [STOP CC] twice and [PLAY BB] next,
so that playback restarts from the first
track in the original order. However, your
programmed playback can be restarted
when you follow the above steps. (Your
programs are still stored until either the
disc is remove or power is turned off.)
• To repeat the current track in the program,
hit
[REPEAT] repeatedly until “TRACK’’
appears during playback.
• To repeat the entire program, hit
repeatedly until “ALL’’ appears during
playback.
<Example : CD>
• Up to 99 tracks can be
ordered.
If eight or more tracks were in a
•
program, use
to see all the tracks.
• While an MP3/WMA folder
is open:
Hit [BB] when you want to
–
go to the next hierarchy.
Hit [
–
go back to the previous
hierarchy (except for the
top hierarchy).
[SKIP HH,GG]
ss
]
when you want to
[ENTER] at
[REPEAT]
EN
Special Settings
DVD-V
DVD-V
CD
CD
DVD-V
DVD-V
1.ENG/6
DVD-V
DVD-V
1 / 8
ANGLE
ON
OFF
DVD-V
DVD-V
WMA
WMA
MP3
MP3
CDCDDVD-V
DVD-V
1.ENG/6
Subtitle Language
Audio Language
2
2
ENTERENTER
OFF
This unit allows you to select a subtitle
language (if available) during DVD playback.
1
1
PLAY
SUB TITLE
Each time you hit [SUBTITLE], subtitle
language changes as example below.
ENG
FRE
(English subtitles)
(French subtitles)
...
OFF
(no subtitles)
To set subtitle ON/OFF
1
1
PLAY
SUB TITLE
2
2
Hint
Hint
• If your language is not shown after press-
[AUDIO] or [SUBTITLE] several times,
ing
the disc may not have that language.
However, some discs allow audio language
or subtitle language setting on the disc
menu. (Operation varies depending on the
disc, so refer to the manual along with the
disc.)
• When “NOT AVAILABLE” appears on the
TV screen, it means no subtitle is recorded
on the scene.
• If you choose a language that has three-letter-language code, the code will be displayed every time you change the subtitle
language setting. If you choose any other
languages, ‘---’ will be displayed instead.
(Refer to page 18.)
• Some discs will only allow you to change
the subtitle from the disc menu. Refer to the
manual accompanying the discs for details.
OFF
This unit allows you to select an audio
language (if multiple languages areavailable on disc) during DVD playback.
1
1
PLAY
AUDIO
Each time you hit [
1.ENG Dolby D 3/2.1ch 48k/ 3
AUDIO]
, audio
language changes as example below.
ENG
SPA
(English audio)
(Spanish audio)
...
FRE
Hint
Hint
• Some discs will only allow you to change
the audio setting from the disc menu. Refer
to the manual accompanying the discs for
details.
(French audio)
Camera Angles
Some DVD discs may contain scenes which have been
shot simultaneously from various angles. You can change the camera angle if the () icon appears on
the screen. If the “ANGLE ICON” set-
ting is “OFF” in the OTHERS menu, the
() icon will not appear. (Refer to
pages 14-16.)
1
1
PLAY
Black Level Setting
Adjust the Black Level Setting to make
the dark areas of the TV picture brighter.
1
1
PLAY
MODE
ON: Makes the dark areas brighter.
OFF: Shows the original picture as recorded.
3
3
RETURN
Stereo Sound Mode
This unit allows you to select a sound
mode during CD playback.
1
1
PLAY
AUDIO
Each time you hit [
STEREO
AUDIO]
, sound
mode changes as example below.
STEREO
(right and left channels
are active)
L-ch
R-ch
(left channel is active)
(right channel is active)
Virtual Surround
You can enjoy stereophonic virtual
world on your existing 2 channel stereo
system.
• Virtual Surround will not be effective if the
sound mode is set to something other than
STEREO. Refer to “Stereo Sound Mode”.
1
Functions
–13–
EN
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
4:3 LETTER BOX
DOLBY DIGITAL BITSTREAM
AUDIO
ORIGINAL
ENGLISH
FRENCH
SUBTITLE
OFF
ENGLISH
FRENCH
DISC MENU
ENGLISH
FRENCH
SPANISH
PLAYER MENU
ENGLISH
FRANÇAIS
ESPAÑOL
DVD Setup
UICK SETUP Menuu
QQUICK SETUP Men
You can select the “PLAYER MENU”, “TV ASPECT” or “DOLBY DIGITAL” from the QUICK SETUP menu quickly.
1
1
STOP
SETUP
2
2
or
<SETUP MENU>
Confirm that “QUICK” is selected.
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
DOLBY DIGITAL BITSTREAM
ENTER
CUST
CUST
4:3 LETTER BOX
OM Menuu
OM Men
You can change the settings of the unit.
QUICK
on pages 14-16 indicates DVD Setup menus also accessible from the QUICK SETUP menu.
•
1
1
STOP
SETUP
<SETUP MENU>
Functions
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
DOLBY DIGITAL BITSTREAM
LANGUAGE menu
4:3 LETTER BOX
ENTERENTER
DISPLAY menu
Select the desired item.
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
DOLBY DIGITAL BITSTREAM
•
Refer to the sections “PLAYER
MENU”, “TV ASPECT” or “DOLBY
DIGITAL” on page 14 or 15.
2
2
oror
Select “CUSTOM”.
AUDIO menu
4:3 LETTER BOX
ENTERENTER
ENTERENTER
PARENTAL menu
A
P14 Step 5)
P15 Step 5)
B
P15 Step 5)
C
3
3
Select the desired item.
ENTER
ENTERENTER
OTHERS menu
DISPLAY
TV ASPECT4:3 LETTER BOX
STILL MODEAUTO
ENTER
page 14
LANGUAGE Setting
A
A
ENTER
page 15
Follow steps 1) to 3) in the “CUSTOM Menu” section above.
Select the desired item.
4
4
LANGUAGE menu
ENTER
ENTERENTER
or
5
5
AUDIO ∗∗1 ∗∗2
(Default: ORIGINAL)
Sets the audio language.
SUBTITLE:∗∗1 ∗∗2
(Default: OFF)
Sets the subtitle language.
DISC MENU:∗∗1
(Default: ENGLISH)
Sets the language in DVD
menu.
PLAYER MENU:
(Default: ENGLISH)
Sets the language for the
On-Screen Display.
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
ENTER
B
page 15
Select the desired language.
or
QUICK
–14–
ON
ON
BITSTREAM
C
PARENTAL LEVEL ALL
ENTER
page 16
ENTERENTER
OTHERS
ANGLE ICON ON
AUTO POWER OFF
page 16
ON
E
ENTER
D
6 To exit the menu.
6
Hint
Hint
SETUP
∗1
• Language options are not available
with some discs.
• If OTHER is selected in the AUDIO,
SUBTITLE or DISC MENU screen,
press four-digit number to enter the
code for the desired language. (Refer
to the language code list on page 18.)
• Only the languages supported by the
disc can be selected.
∗2
• Language setting for Audio and
Subtitle are not available with some
discs. Then hit
[SUBTITLE]. Details are on page 13.
[AUDIO] and
EN
DISPLAY Setting
TV ASPECT
4:3 LETTERBOX
STILL MODE
AUTO
STILL MODE
AUTO
FIELD
FRAME
DRCON
DOWN SAMPLING
ON
DOLBY DIGITALBITSTREAM
ON
ON
PCM
DRCON
DOWN SAMPLING
ON
DOLBY DIGITALBITSTREAM
ON
OFF
BITSTREAM
B
You can change the display functions. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14.
4
Select the desired item.
4
or
DISPLAY menu
DISPLAY
TV ASPECT4:3 LETTER BOX
STILL MODEAUTO
ENTER
5
5
TV ASPECT:
QUICK
(Default: 4:3 LETTER BOX)
See Hint to the right.
TV ASPECT
STILL MODE
4:3 LETTERBOX
AUTO
STILL MODE:
(Default: AUTO)
See Hint to the right.
ENTERENTER
ENTERENTER
TV ASPECT
4:3
LETTER BOX
4:3
PAN & SCAN
16:9
WIDE
Select the
desired
setting.
or
Select the
desired
setting.
or
ENTERENTER
ENTERENTER
6 To exit the menu
6
SETUP
Hint
Hint
TV ASPECT:
• Select “4:3 LETTER BOX”, so
that black bars may appear on
the top and bottom of the
screen.
• Select “4:3 PAN & SCAN” for
a full height picture with both
sides adjusted.
• Select “16:9 WIDE” if a widescreen TV is connected to this
unit.
STILL MODE:
• Select “AUTO” usually.
• If you select “FIELD”, the pic-
ture in the still mode will be
stabilized.
• If you select “FRAME”, the
picture in the still mode will be
highly defined.
AUDIO Setting
C
Choose the appropriate audio settings for your equipments. It only affects during the playback of DVD discs. Follow steps 1)
to 3) in the “CUSTOM Menu” section on page 14.
4
4
Select the desired item.
or
AUDIO menu
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
ENTER
ON
ON
BITSTREAM
5
5
DRC (Dynamic Range Control):
(Default: ON)
Set to “ON” to compress the range between soft and loud sounds.
DRCON
DOWN SAMPLING
DOLBY DIGITALBITSTREAM
ON
ENTERENTER
OFF
ON
BITSTREAM
DOWN SAMPLING:
(Default: ON)
Set to “ON” when outputting in 48 kHz.
Set to “OFF” when outputting the original sound.
ENTERENTER
DOLBY DIGITAL:
QUICK
(Default: BITSTREAM)
Set to “BITSTREAM” when the unit is connected to a Dolby Digital receiver.
• BITSTREAM: Outputs a Dolby Digital Signals.
• PCM: Convert the Dolby Digital into PCM (2 channel).
ENTERENTER
6 To exit the menu
6
Hint
Hint
SETUP
DRC:
• This function is available
only on the discs which
are recorded in the Dolby
Digital format.
DOWN SAMPLING:
• When playing disc with
copyright protection, the
sound will be down sampled at 48kHz, even if
you set to OFF.
• This function is available
only on digital outputting
of a disc recorded in
96kHz.
Functions
–15–
EN
PARENTAL Setting
ENTERENTER
ENTERENTER
PASSWORD CHANGE
PARENTAL LEVEL ALL
PARENTAL LEVEL
ALL
8
7 [NC-17]
6 [R]
PASSWORD CHANGE
PARENTAL LEVEL ALL
ENTER
ANGLE ICON ON
AUTO POWER OFF
ON
ON
OFF
ANGLE ICON ON
AUTO POWER OFF
ON
OFF
ON
OTHERS
ENTER
ANGLE ICON ON
AUTO POWER OFF
ON
ENTERENTER
123
456
789
0
ENTERENTER
ENTERENTER
SETUP
SETUP
ENTERENTER
ENTERENTER
123
456
789
0
123
456
789
0
D
Parental Control limits the disc viewing that exceed your settings. (An incorrect password will not play.)
This feature prevents your children from viewing inappropriate materials.
arentalLeLe
PParental
Parental Level allows you to set the rating levels of your DVD discs. Playback will stop if the ratings exceed the levels you set.
vels
vels
Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14.
To exit
4
Enter your desired four-
4
digit password (except
for 4737).
5
Select “PARENTAL
5
LEVEL”.
6
Select the
6
desired level.
or
or
7
7
the menu
SETUP
PARENTAL menu
CONTROL LEVELS
• ALL:All parental locks are cancelled.
PASSWORD
ENTER
If you have set a password already,
or
enter the current four-digit
password.
o Chang
Functions
TTo Chang
e the P
e the P
asswworor
ass
You can change your password for parental controls. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14.
4
4
Enter your desired fourdigit password (except
for 4737).
• Level 8:DVD softwares of any grades (adult/general/children) can be played back.
• Levels 7 to 2: Only DVD softwares intended for general use and children can be played
• Level 1:Only DVD softwares intended for children can be played back, with those
TIPS FOR LEVELS
• 7 [NC-17]:No one under 17 admitted
• 6 [R]:Restricted; under 17 requires accompanying parent or adult guardian
• 4 [PG13]:Unsuitable for children under 13
• 3 [PG]:Parental Guidance suggested
• 1 [G]:General Audience
Hint
Hint
• DVD-Video discs may not respond to the parental lock settings. Make sure this function
works with your DVD-Video discs.
d f
or P
d f
5
5
arental Contr
or P
arental Contr
Select “PASSWORD
CHANGE”.
back.
intended for adult and general use prohibited.
ols
ols
6
Enter your new
6
four-digit password
(except for 4737).
or
7
7
To exit
the menu
PARENTAL menu
E
You can change the other functions. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14.
4
4
OTHERS menu
ENTER
OTHERS Setting
Select the desired item
or
5
5
ANGLE ICON:
(Default: ON)
Set to “ON” to show the angle icon when multiple camera
angles are available during DVD playback.
AUTO POWER OFF:
(Default: ON)
Set to “ON” to turn this unit off automatically after
30 minutes of no use.
–16–
Hint
Hint
•
Record the password in
case you forget it.
• I
f you forget the pass-
PASSWORD
ENTER
word, hit [4], [7], [3], [7]
at step 4), then enter your
new password.
•
Password will be cleared
and parental levels will be
set to “ALL”.
6 To exit the menu
6
EN
Reset to the Default Setting (Except for PARENTAL Setting)
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
4:3 LETTER BOX
DOLBY DIGITAL BITSTREAM
INITIALIZE
Initialize?
NO
YES
ENTER
SETUP
SETUP
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
4:3 LETTER BOX
DOLBY DIGITAL BITSTREAM
STOP
ENTERENTER
ENTERENTER
1
1
2
2
or
3
3
To exit
4
4
or
the menu
<SETUP MENU>
Select “INITIALIZE”.
Select “YES”.
Hit
twice.
Hint
Hint
•
When you cancel
to initialize at step
3), select “NO”.
Information
Troubleshooting Guide
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit consulting the following checklist.
ProblemSolution
No power–Check if the AC power cord is properly connected.
No sound or picture–Check if the TV is switched on.
Distorted picture–Sometimes a small amount of picture distortion may appear.
Completely distorted picture or –Connect the unit directly to the TV.
black/white picture with DVD–Make sure the disc is compatible with the unit.
No sound or distorted sound–Adjust the volume.
No audio at digital output–Check the digital connections.
No DTS audio is output–This unit does not support DTS audio.
Picture freezes momentarily–Check the disc for fingerprints/scratches and
during playbackclean with a soft cloth wiping from center to edge.
Disc can’t be played–Clean the disc.
No return to start-up screen when –Reset the unit by switching the unit off, then on again.
disc is removed
The unit does not respond to –
the remote control–Reduce the distance to the unit.
Buttons do not work or the unit stops–To completely reset the unit, unplug the AC
respondingcord from the AC outlet for 5-10 seconds.
The unit does not respond to some –Operations may not be permitted by the disc.
operating commands during playbackRefer to the instructions of the disc.
The unit cannot read –Use a commonly available cleaning CD/DVD to
CDs/DVDsclean the lens before sending the unit for repair.
Angle does not switch–The angle cannot be switched for DVDs which do not contain multi-
Playback does not start when the title is selected –Check the “PARENTAL” setting.
The password for rating level has been forgotten–Enter the default password “4737”, then your forgotten password
Disc cannot be inserted–Check if any disc is already in?
Disc cannot be taken out–Press and hold [EJECT A] on the unit for more than 5 seconds.
NOTES:
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual
for more details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
–
Unplug the outlet once, and wait for 5-10seconds and then plug it in again.
–Check the video connection.
–Check the VIDEO/AUDIO cable connections to the TV.
(See Connection to a TV)
This is not a malfunction.
–Connect the unit directly to the TV.
–Check that the speakers are connected correctly.
–Check if the audio format of the selected audio language matches
your receiver capabilities.
This is not a malfunction.
–Clean the disc.
–Ensure the disc label is facing up.
–Check if the disc is defective by trying another disc.
–Cancel the parental lock or change the control level.
–Insert a correct disc that plays on this unit.
–Handle a disc with special care so that it does not have fingerprints,
scratches, or dusts on its surface.
Aim the remote control directly at the sensor on the front of the unit.
–Replace the batteries in the remote control.
–Re-insert the batteries with their polarities (+/– signs) as indicated.
–
Tune your radio to an empty AM station so that you hear a lot of noises.
Then, turn the volume up. If you hear some signal sound from the radio
by pressing buttons on the remote control, the remote control is working.
ple angles. In some cases multiple angles are only recorded for
specific scenes.
will be cleared.
–17–
Information
EN
Specifications
Output signal format:
NTSC color
Power source:
120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption:
10 W (standby: 0.8 W)
Operating temperature:
41°F (5°C) to 104°F (40°C)
Dimensions:
W : 10"(255 mm)
H : 2 1/16" (59 mm)
D : 9 9/16" (243.5 mm)
Weight :
Approx 2.8 lbs (1.3 kg)
• Designs and specifications are subject
to change without notice.
• If there is a discrepancy between languages, the default language will be
English.
Cambodian5759
Catalan4947
Chinese [CHI]7254
Corsican4961
Croatian5464
Czech4965
Danish [DAN]5047
Dutch [DUT]6058
English [ENG]5160
Esperanto5161
Estonian5166
Faroese5261
Fiji5256
Finnish [FIN]5255
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language
setting on page 13. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)
Information
A-B
C-E
F-H
CodeLanguageCodeLanguageCodeLanguageCode
French [FRE]5264
Frisian5271
Galician5358
Georgian5747
German [GER]5051
Greek [GRE]5158
Greenlandic5758
Guarani5360
Gujarati5367
Hausa5447
Hebrew5569
Hindi5455
Hungarian [HUN]5467
Icelandic [ICE]5565
Indonesian5560
Interlingua5547
Interlingue5551
Inupiak5557
Irish [IRI]5347
Italian [ITA]5566
Japanese [JPN]5647
Javanese5669
Kannada5760
Kashmiri5765
Kazakh5757
Kinyarwanda6469
Kirghiz5771
Kirundi6460
Korean [KOR]5761
Kurdish5767
FUNAI CORP. will repair this Emerson product, free of charge in the
USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS:
LABOR:FUNAI CORP. will provide the labor without charge for
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required
together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the
product are altered, replaced, defaced, missing or if service was
attempted by an unauthorized service center. This Emerson Limited
warranty does not apply to any product not purchased and used in
the United States.
This product is produced for home use and this warranty only covers
failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment,
or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident,
misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or
office use of this product or damage which results from fire, flood,
lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY
ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC
PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL
FUNAI CORP. will provide parts to replace defective
parts without charge for one (1) year from the date of
original retail purchase. Certain parts are excluded
from this warranty.
a period of ninety (90) days from the date of original
retail purchase.
–18–
IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR
CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES
INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST
BE PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO
FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO
STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU
ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF
THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN
OF THIS PRODUCT WITHOUT PRIOR NOTICE.
To locate your nearest Emerson Authorized Service Center or for
general service procedure, please call or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-256-2487
http://www.EmersonAudioVideo.com
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
EN
POWER
AUDIO
SUBTITLE
ANGLE
REPEAT
CLEAR
A-B
PAUSE
SLOW
SKIP
EJECT
DISPLAY
SEARCH
MODE
123
456
789
0 +10
PLAY
REVFWD
STOP
Español
WMA
WMA
MP3
MP3
CDCDDVD-V
DVD-V
PLAYER MENU
ENGLISH
FRANÇAIS
ESPAÑOL
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
4:3 LETTER BOX
DOLBY DIGITAL BITSTREAM
ENTERENTER
ENTERENTER
ENTERENTER
• Para encender o apagar la
unidad.
• Para encender o apagar la
unidad.
• Para mostrar el modo de
disco actual.
• Para mostrar el modo de
disco actual.
• Presione para ejectar el
disco.
• Presione para ejectar el
disco.
• Para hacer una pausa en la
reproducción del disco.
• Para empezar la
reproducción del disco.
• Para empezar la
reproducción del disco.
• Para seleccionar
directamente el capítulo o
título.
• Para seleccionar
directamente la canción.
• Para seleccionar los ángulos
de cámara en un disco.
• Para seleccionar subtítulos
en un disco.
• Para seleccionar idiomas de
audio en un disco.
•
Para seleccionar ESTÉREO
L-ch o R-ch. (CD)
• Para repetir entre su punto A
y B seleccionado.
•
Para repetir entre su punto A y B
seleccionado. (CD)
• Para reproducir
repetidamente un capítulo o
título.
•
Para reproducir repetidamente
una canción o disco. (CD)
•
Para reproducir repeticlamenfe una
cancieón, grupo o disco. (MP3/WMA)
• Para activar/desactivar el
nivel del negro.
•
Para disponer el orden de reproducción
o la reproducción aleatoria.
• Para llamar el Menú en un
disco.
• Para llamar el menú inicial
en un disco.
•
Para volcer al archivo superior de
la jeraraúia más alta en el programa
y en la lista de archivo. (MP3/WMA)
• Para ampliar la imagen de
vídeo en DVD.
• Para activar/desactivar el
ambiental virtual.
• Para activar/desactivar el
ambiental virtual.
• Para volver a la operación
anterior en el menú.
• Para volver a la operación
anterior en el menú.
• Para buscar un capítulo, título
o tiempo.
• Para colocar o buscar los
marcadores.
• Para buscar una canción.
• Para buscar el tiempo. (CD)
•
Para colocar o buscar los
marcadores. (CD)
• Para borrar los marcadores.
•
Para borrar los marcadores. (CD)
• Para eliminar el Nº de estado
en la entrada de programa.
• Para borrar los números mal
entrados.
• Para borrar el punto para la
repetición A-B. (CD)
• Para borrar los números mal
entrados.
• Para borrar el punto para la
repetición A-B.
•
Para buscar en avance/
retroceso por un disco.
•
Para empezar la reproducción
en avance lento/retroceso
durante el modo de pausa.
• Para buscar en avance/
retroceso por un disco.
•
Para llamar la liseade archivo.
(MP3/WMA)
•
Para avanzar la reproducción un cuadro
cada vez.
•
Para hacer una pausa en la reproducción.
• Para parar la reproducción. • Para parar la reproducción.
• Para saltar capítulos.• Para saltar canciones.
• Para llamar el menú de
ajustes de DVD.
• Para llamar el menú de
ajustes de DVD.
• Para mover el cursor y
determinar la posición.
• Para mover el cursor y
determinar la posición.
POWER
DISPLAY
MENU
TOP MENU
ZOOM
SUBTITLE
MODE
ANGLE
SEARCH
MODE
REPEAT
A-B
AUDIO
CLEAR
123
456
789
0
+1 0
PAUSE
PLAY
STOP
SETUP
DVD-V
DVD-V
Botón
(Orden alfabético)
Disco
ENTER
RETURN
REVFWD
EJECT
SKIP
CD
CD
MP3
MP3
WMA
WMA
POWER
STOP
POWER
PLAY
✄
Conexiones
1
Si su televisor tiene entradas
de AUDIO/VIDEO vea la
sección “Connection to a TV”
en la página 6 en el Manual de
Manejo. En caso contrario, vea
la sección “RF Modulator
Connection” en la página 6 en
el Manual de Manejo.
Instalación de las pilas
2
en el control remoto
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
DOLBY DIGITAL BITSTREAM
OK
3
4:3 LETTER BOX
SETUP
1
3
1
1
2
2
Confirme que ha seleccionado
“PLAYER MENU”.
3
3
4 Para salir del menú.
4
2
Para cambiar el idioma
en la pantalla
STOP
SETUP
o
Confirme que ha
seleccionado “QUICK”.
Seleccione el idioma
deseado para las
indicaciones en la pantalla.
Reproducción
4
Antes.
¡
Encienda el televisor, amplificador y
otros equipos conectados a esta
unidad. Asegúrese que el televisor y
el sintonizador de audio (de venta en
los comercios) están en el canal
correcto.
1
1
3
3
Control remoto
5
–19–
4
4
1
1
3
Para empezar
3
la reproducción
2
2
4
4
Ponga un
disco con la
etiqueta
hacia
izquierda.
Para parar la
reproducción
Español
ES
POWER
AUDIO
SUBTITLE
ANGLE
REPEAT
CLEAR
A-B
PAUSE
SLOW
SKIP
EJECT
DISPLAY
SEARCH
MODE
123
456
789
0 +10
PLAY
REVFWD
STOP
Quick Use Guide
PLAYER MENU
ENGLISH
FRANÇAIS
ESPAÑOL
• To turn the unit on or off.•To turn the unit on or off.
• To display the current disc
mode.
• To display the current disc
mode.
• To select chapter or title
directly.
• To select track directly.
• To select camera angles on
a disc.
• To select subtitles on a disc.
• To select audio languages on
a disc.
• To select STEREO,
L-ch or R-ch. (CD)
• To repeat between your
chosen point A and B.
• To repeat between your
chosen point A and B. (CD)
• To play a chapter or title
repeatedly.
• To play a track or disc
repeatedly. (CD)
• To play a track, group or disc
repeatedly. (MP3/WMA)
• To return to the previous
operation in menu.
• To set black level on/off.
• To set virtual surround on/off.
• To arrange the playing
order or play randomly.
• To set virtual surround on/off.
• To call up the Menu
on a disc.
• To call up the Top Menu
on a disc.
• To magnify part of a picture.
(x2/x4)
• To return to the previous
operation in menu.
• To search chapter, title or time.
• To set or search the
markers.
• To search track.
• To search time. (CD)
• To set or search the
markers. (CD)
• To clear the markers.
• To cancel the point for A-B
repeat.
• To cancel the point for A-B
repeat. (CD)
• To clear the markers. (CD)
• To remove status number
in program input.
• To clear the numbers
entered incorrectly.
• To clear the numbers
entered incorrectly.
• To search forward/backward
through a disc.
• To begin slow forward
/reverse playback during
the pause mode.
• To search forward/backward
through a disc.
• To call up the file list.
(MP3/WMA)
• To advance playback
one frame at a time.
• To pause disc playback.
• To pause disc playback.
• To stop playback.• To stop playback.
•
To return to the top file of the
highest hievarcy in the program
and file list. (MP3/WMA)
• To skip chapters.• To skip tracks.
• To begin disc playback.• To begin disc playback.
• To call up the DVD setup
menu.
• To call up the DVD setup
menu.
• To move the cursor and
determine its position.
• To move the cursor and
determine its position.
POWER
DISPLAY
MENU
TOP MENU
ZOOM
SUBTITLE
MODE
ANGLE
SEARCH
MODE
REPEAT
A-B
AUDIO
CLEAR
123
456
789
0
+1 0
PAUSE
PLAY
STOP
SETUP
DVD-V
DVD-V
Button
(Alphabetical order)
Disc
ENTER
RETURN
REVFWD
SKIP
CD
CD
MP3
MP3
WMA
WMA
• Hit to remove the disc.• Hit to remove the disc.
EJECT
SETUP
ENTERENTER
ENTERENTER
ENTERENTER
SETUP
STOP
POWER
POWER
STOP
PLAY
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
4:3 LETTER BOX
DOLBY DIGITAL BITSTREAM
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT
4:3 LETTER BOX
DOLBY DIGITAL BITSTREAM
OK
If your TV has AUDIO/VIDEO
input jacks, see the section
“Connection to a TV” on page
6 of the Owner’s Manual. If not,
see the section “RF Modulator
Connection” on page 6 of the
Owner’s Manual.
1
1
2
2
3
3
4 To exit the menu.
4
Printed in China
Connections
1
Installing the Batteries
2
for the Remote Control
2
To Change the On-
3
Screen Language
1
Confirm that “PLAYER MENU” is selected.
Confirm that “QUICK” is
selected.
Select the desired language
for the On-Screen Display.
or
3
Playback
4
Before:
¡Turn on the TV, amplifier and any other
equipments which are connected to this
unit. Make sure the TV and audio receiver (commercially available) are set to the
correct channel.
1
1
3
3
Remote Control
5
4
4
1
1
3
3
DVD-V
DVD-V
To start
playback
CD
CD
2
2
4
4
MP3
MP3
To stop
playback
WMA
WMA
Insert a
disc with
label
facing to
the left.
1VMN20420 / E61S0UD ★★★★
✄
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.